Abstract: The steady mixed convection boundary layer flow from
a vertical cone in a porous medium filled with a nanofluid is
numerically investigated using different types of nanoparticles as Cu
(copper), Al2O3 (alumina) and TiO2 (titania). The boundary value
problem is solved by using the shooting technique by reducing it
into an ordinary differential equation. Results of interest for the local
Nusselt number with various values of the constant mixed convection
parameter and nanoparticle volume fraction parameter are evaluated.
It is found that dual solutions exist for a certain range of mixed
convection parameter.
Abstract: A two-dimensional numerical simulation of crossflow
around four cylinders in an in-line rectangular configuration is
studied by using the lattice Boltzmann method (LBM). Special
attention is paid to the effect of the spacing between the cylinders.
The Reynolds number ( Re ) is chosen to be e 100 R = and the
spacing ratio L / D is set at 0.5, 1.5, 2.5, 4.0, 5.0, 6.0, 7.0, 8.0, 9.0
and 10.0. Results show that, as in the case of four cylinders in an inline
rectangular configuration , flow fields show four different
features depending on the spacing (single square cylinder, stable
shielding flow, wiggling shielding flow and a vortex shedding flow)
are observed in this study. The effects of spacing ratio on physical
quantities such as mean drag coefficient, Strouhal number and rootmean-
square value of the drag and lift coefficients are also presented.
There is more than one shedding frequency at small spacing ratios.
The mean drag coefficients for downstream cylinders are less than
that of the single cylinder for all spacing ratios. The present results
using the LBM are compared with some existing experimental data
and numerical studies. The comparison shows that the LBM can
capture the characteristics of the bluff body flow reasonably well and
is a good tool for bluff body flow studies.
Abstract: This paper deals with condition monitoring of electric switch machine for railway points. Point machine, as a complex electro-mechanical device, switch the track between two alternative routes. There has been an increasing interest in railway safety and the optimal management of railway equipments maintenance, e.g. point machine, in order to enhance railway service quality and reduce system failure. This paper explores the development of Kolmogorov- Smirnov (K-S) test to detect some point failures (external to the machine, slide chairs, fixing, stretchers, etc), while the point machine (inside the machine) is in its proper condition. Time-domain stator Current signatures of normal (healthy) and faulty points are taken by 3 Hall Effect sensors and are analyzed by K-S test. The test is simulated by creating three types of such failures, namely putting a hard stone and a soft stone between stock rail and switch blades as obstacles and also slide chairs- friction. The test has been applied for those three faults which the results show that K-S test can effectively be developed for the aim of other point failures detection, which their current signatures deviate parametrically from the healthy current signature. K-S test as an analysis technique, assuming that any defect has a specific probability distribution. Empirical cumulative distribution functions (ECDF) are used to differentiate these probability distributions. This test works based on the null hypothesis that ECDF of target distribution is statistically similar to ECDF of reference distribution. Therefore by comparing a given current signature (as target signal) from unknown switch state to a number of template signatures (as reference signal) from known switch states, it is possible to identify which is the most likely state of the point machine under analysis.
Abstract: In this paper, stabilization of an Active Magnetic Bearing (AMB) system with varying rotor speed using Sliding Mode Control (SMC) technique is considered. The gyroscopic effect inherited in the system is proportional to rotor speed in which this nonlinearity effect causes high system instability as the rotor speed increases. Also, transformation of the AMB dynamic model into a new class of uncertain system shows that this gyroscopic effect lies in the mismatched part of the system matrix. Moreover, the current gain parameter is allowed to be varied in a known bound as an uncertainty in the input matrix. SMC design method is proposed in which the sufficient condition that guarantees the global exponential stability of the reduced-order system is represented in Linear Matrix Inequality (LMI). Then, a new chattering-free control law is established such that the system states are driven to reach the switching surface and stay on it thereafter. The performance of the controller applied to the AMB model is demonstrated through simulation works under various system conditions.
Abstract: A cart-ball system is a challenging system from the
control engineering point of view. This is due to the nonlinearities,
multivariable, and non-minimum phase behavior present in this
system. This paper is concerned with the problem of modeling and
control of such system. The objective of control strategy is to place
the cart at a desired position while balancing the ball on the top of the
arc-shaped track fixed on the cart. A State-Feedback Controller
(SFC) with a pole-placement method will be designed in order to
control the system. At first, the mathematical model of a cart-ball
system in the state-space form is developed. Then, the linearization of
a model will be established in order to design a SFC. The integral
control strategy will be performed as to control the cart position of a
system. Simulation work is then performed using
MATLAB/SIMULINK software in order to study the performance of
SFC when applied to the system.
Abstract: In this article, various models of surface tension force (CSF, CSS and PCIL) for interfacial flows have been applied to dynamic case and the results were compared. We studied the Kelvin- Helmholtz instabilities, which are produced by shear at the interface between two fluids with different physical properties. The velocity inlet is defined as a sinusoidal perturbation. When gravity and surface tension are taking into account, we observe the development of the Instability for a critic value of the difference of velocity of the both fluids. The VOF Model enables to simulate Kelvin-Helmholtz Instability as dynamic case.
Abstract: The objective of this manuscript is to find area under the plasma concentration- time curve (AUC) for multiple doses of salbutamol sulphate sustained release tablets (Ventolin® oral tablets SR 8 mg, GSK, Pakistan) in the group of 18 healthy adults by using computational mathematics techniques. Following the administration of 4 doses of Ventolin® tablets 12 hourly to 24 healthy human subjects and bioanalysis of obtained plasma samples, plasma drug concentration-time profile was constructed. AUC, an important pharmacokinetic parameter, was measured using integrated equation of multiple oral dose regimens. The approximated AUC was also calculated by using computational mathematics techniques such as repeated rectangular, repeated trapezium and repeated Simpson's rule and compared with exact value of AUC calculated by using integrated equation of multiple oral dose regimens to find best computational mathematics method that gives AUC values closest to exact. The exact values of AUC for four consecutive doses of Ventolin® oral tablets were 150.5819473, 157.8131756, 164.4178231 and 162.78 ng.h/ml while the closest values approximated AUC values were 149.245962, 157.336171, 164.2585768 and 162.289224 ng.h/ml, respectively as found by repeated rectangular rule. The errors in the approximated values of AUC were negligible. It is concluded that all computational tools approximated values of AUC accurately but the repeated rectangular rule gives slightly better approximated values of AUC as compared to repeated trapezium and repeated Simpson's rules.
Abstract: High voltage generators are being subject to higher
voltage rating and are being designed to operate in harsh conditions.
Stator windings are the main component of generators in which
Electrical, magnetical and thermal stresses remain major failures for
insulation degradation accelerated aging. A large number of
generators failed due to stator winding problems, mainly insulation
deterioration. Insulation degradation assessment plays vital role in the
asset life management. Mostly the stator failure is catastrophic
causing significant damage to the plant. Other than generation loss,
stator failure involves heavy repair or replacement cost. Electro
thermal analysis is the main characteristic for improvement design of
stator slot-s insulation. Dielectric parameters such as insulation
thickness, spacing, material types, geometry of winding and slot are
major design consideration. A very powerful method available to
analyze electro thermal performance is Finite Element Method
(FEM) which is used in this paper. The analysis of various stator coil
and slot configurations are used to design the better dielectric system
to reduce electrical and thermal stresses in order to increase the
power of generator in the same volume of core. This paper describes
the process used to perform classical design and improvement
analysis of stator slot-s insulation.
Abstract: Several numerical schemes utilizing central difference
approximations have been developed to solve the Goursat problem.
However, in a recent years compact discretization methods which
leads to high-order finite difference schemes have been used since it
is capable of achieving better accuracy as well as preserving certain
features of the equation e.g. linearity. The basic idea of the new
scheme is to find the compact approximations to the derivative terms
by differentiating centrally the governing equations. Our primary
interest is to study the performance of the new scheme when applied
to two Goursat partial differential equations against the traditional
finite difference scheme.
Abstract: Nowaday-s, many organizations use systems that
support business process as a whole or partially. However, in some
application domains, like software development and health care
processes, a normative Process Aware System (PAS) is not suitable,
because a flexible support is needed to respond rapidly to new
process models. On the other hand, a flexible Process Aware System
may be vulnerable to undesirable and fraudulent executions, which
imposes a tradeoff between flexibility and security. In order to make
this tradeoff available, a genetic-based anomaly detection model for
logs of Process Aware Systems is presented in this paper. The
detection of an anomalous trace is based on discovering an
appropriate process model by using genetic process mining and
detecting traces that do not fit the appropriate model as anomalous
trace; therefore, when used in PAS, this model is an automated
solution that can support coexistence of flexibility and security.
Abstract: Simulation accuracy by recent dynamic vehicle
simulation multidimensional expression significantly has progressed
and acceptable results not only for passive vehicles but also for
active vehicles normally equipped with advanced electronic
components is also provided. Recently, one of the subjects that has it
been considered, is increasing the safety car in design. Therefore,
many efforts have been done to increase vehicle stability especially
in the turn. One of the most important efforts is adjusting the camber
angle in the car suspension system. Optimum control camber angle in
addition to the vehicle stability is effective in the wheel adhesion on
road, reducing rubber abrasion and acceleration and braking. Since
the increase or decrease in the camber angle impacts on the stability
of vehicles, in this paper, a car suspension system mechanism is
introduced that could be adjust camber angle and the mechanism is
application and also inexpensive. In order to reach this purpose, in
this paper, a passive double wishbone suspension system with
variable camber angle is introduced and then variable camber
mechanism designed and analyzed for study the designed system
performance, this mechanism is modeled in Visual Nastran software
and kinematic analysis is revealed.
Abstract: Mobile Learning (M-Learning) is a new technology
which is to enhance current learning practices and activities for all
people especially students and academic practitioners UTP is
currently, implemented two types of learning styles which are
conventional and electronic learning. In order to improve current
learning approaches, it is necessary for UTP to implement m-learning
in UTP. This paper presents a study on the students- perceptions on
mobile utilization in the learning practices in UTP. Besides, this
paper also presents a survey that was conducted among 82 students
from System Analysis and Design (SAD) course in UTP. The survey
includes basic information of mobile devices that have been used by
the students, opinions on current learning practices and also the
opinions regarding the m-learning implementation in the current
learning practices especially in SAD course. Based on the results of
the survey, majority of the students are using the mobile devices that
can support m-learning environment. Other than that, students also
agreed that current learning practices are ineffective and they believe
that m-learning utilization can improve the effectiveness of current
learning practices.
Abstract: One of the major causes of voltage instability is the reactive power limit of the system. Improving the system's reactive power handling capacity via Flexible AC transmission System (FACTS) devices is a remedy for prevention of voltage instability and hence voltage collapse. In this paper, the effects of SVC and STATCOM in Static Voltage Stability Margin Enhancement will be studied. AC and DC representations of SVC and STATCOM are used in the continuation power flow process in static voltage stability study. The IEEE-14 bus system is simulated to test the increasing loadability. It is found that these controllers significantly increase the loadability margin of power systems.
Abstract: In this research, a systematic investigation was carried out to determine the optimum conditions of HDS reactor. Moreover, a suitable model was developed for a rigorous RTO (real time optimization) loop of HDS (Hydro desulfurization) process. A systematic experimental series was designed based on CCD (Central Composite design) and carried out in the related pilot plant to tune the develop model. The designed variables in the experiments were Temperature, LHSV and pressure. However, the hydrogen over fresh feed ratio was remained constant. The ranges of these variables were respectively equal to 320-380ºC, 1- 21/hr and 50-55 bar. a power law kinetic model was also developed for our further research in the future .The rate order and activation energy , power of reactant concentration and frequency factor of this model was respectively equal to 1.4, 92.66 kJ/mol and k0=2.7*109 .
Abstract: Estimation of stature is an important step in developing a biological profile for human identification. It may provide a valuable indicator for unknown individual in a population. The aim of this study was to analyses the relationship between stature and lower limb dimensions in the Malaysian population. The sample comprised 100 corpses, which included 69 males and 31 females between age ranges of 20 to 90 years old. The parameters measured were stature, thigh length, lower leg length, leg length, foot length, foot height and foot breadth. Results showed that mean values in males were significantly higher than those in females (P < 0.05). There were significant correlations between lower limb dimensions and stature. Cross-validation of the equation on 100 individuals showed close approximation between known stature and estimated stature. It was concluded that lower limb dimensions were useful for estimation of stature, which should be validated in future studies.
Abstract: The distribution of macrobenthic polychaetes along
the coastal waters of Penang National Park was surveyed to estimate
the effect of various environmental parameters at three stations
(200m, 600m and 1200m) from the shoreline, during six sampling
months, from June 2010 to April 2011.The use of polychaetes in
descriptive ecology is surveyed in the light of a recent investigation
particularly concerning the soft bottom biota environments.
Polychaetes, often connected in the former to the notion of
opportunistic species able to proliferate after an enhancement in
organic matter, had performed a momentous role particularly with
regard to effected soft-bottom habitats. The objective of this survey
was to investigate different environment stress over soft bottom
polychaete community along Teluk Ketapang and Pantai Acheh
(Penang National Park) over a year period. Variations in the
polychaete community were evaluated using univariate and
multivariate methods. The results of PCA analysis displayed a
positive relation between macrobenthic community structures and
environmental parameters such as sediment particle size and organic
matter in the coastal water. A total of 604 individuals were examined
which was grouped into 23 families. Family Nereidae was the most
abundant (22.68%), followed by Spionidae (22.02%), Hesionidae
(12.58%), Nephtylidae (9.27%) and Orbiniidae (8.61%). It is
noticeable that good results can only be obtained on the basis of good
taxonomic resolution. We proposed that, in monitoring surveys,
operative time could be optimized not only by working at a highertaxonomic
level on the entire macrobenthic data set, but by also
choosing an especially indicative group and working at lower
taxonomic and good level.
Abstract: A cross-sectional study was carried out to determine the prevalence, species characterization and associated risk factors with Eimeria (E.) in sheep of district Toba Tek Singh from April, 2009 to March, 2010. Of the total 486 faecal samples examined for Eimeria, 209 (43%) were found infected with five species of Eimeria. Amongst the identified species of Eimeria, E. ovinoidalis was the commonest one (48.32%), followed in order by E. ahsata, E. intricata, E. parva and E. faurei with prevalence of 45.45, 28.71, 24.40 and 19.14 percent respectively. Peak prevalence was observed in August. Wet season (rainy and post-rainy) was found to be favourable for Eimeria infection. Lambs had significantly higher prevalence (P < 0.05) of Eimeria than adults. Similarly higher prevalence of Eimeria was observed in female as compared to male. Among management and husbandry practices; watering system, housing system, floor type and herd size strongly influenced the prevalence of Eimeria. Coccidiosis was more prevalent in closed housing system, non-cemented floor type, pond watered animals and larger herds (P < 0.05) as compared to open housing system, partially cemented floor type, tap watered animals and smaller herds respectively. Feeding system, breed and body condition of animals were not found as risk factors (P>0.05) influencing prevalence of Eimeria.
Abstract: A biosensor based on glucose oxidase (GOx) immobilized onto nanoparticles zirconium oxide with polyethylene nanocomposite for glucose monitoring has been designed. The CTAB/PEG/ZrO2/GOx nanocomposite was deposited onto screen printed carbon paste (SPCE) electrode via spin coating technique. The properties of CTAB/PEG/ZrO2/GOx were study using scanning electron microscopy (SEM). The SPE modified with the CTAB/PEG/ZrO2/GOx showed electrocatalytical response to the oxidation of glucose when ferrocene carboxaldehyde was used as an artificial redox mediator, which was studied by cyclic voltammetry (CV). Several parameters such as working potential, effect of pH and effect of ZrO2/PEG layers that governed the analytical performance of the biosensor, have been studied. The biosensor was applied to detect glucose with a linear range of 0.4 to 2.0 mmol L−1 with good repetability and reproducibility.
Abstract: This paper presents an analytical framework for an
effective online personal knowledge management (PKM) of
knowledge workers. The development of this framework is prompted
by our qualitative research on the PKM processes and cognitive
enablers of knowledge workers in eight organisations selected from
three main industries in Malaysia. This multiple-case research
identifies the relationships between the effectiveness of four online
PKM processes: get/retrieve, understand/analyse, share, and connect.
It also establishes the importance of cognitive enablers that mediate
this relationship, namely, method, identify, decide and drive.
Qualitative analysis is presented as the findings, supported by the
preceded quantitative analysis on an exploratory questionnaire
survey.
Abstract: This work presents a study on the abrasive water jet
(AWJ) machining. An explicit finite element analysis (FEA) of
single abrasive particle impact on stainless steel 1.4304 (AISI 304) is
conducted. The abrasive water jet machining is modeled by FEA
software ABAQUS/CAE. Shapes of craters in FEM simulation
results were used and compared with the previous experimental and
FEM works by means of crater sphericity. The influence of impact
angle and particle velocity was observed. Adaptive mesh domain is
used to model the impact zone. Results are in good agreement with
those obtained from the experimental and FEM simulation. The
crater-s depth is also obtained for different impact angle and abrasive
particle velocities.