Abstract: In this study, an Artificial Neural Network (ANN)
analytical method has been developed for analyzing earthquake
performances of the Reinforced Concrete (RC) buildings. 66 RC
buildings with four to ten storeys were subjected to performance
analysis according to the parameters which are the existing material,
loading and geometrical characteristics of the buildings. The selected
parameters have been thought to be effective on the performance of
RC buildings. In the performance analyses stage of the study, level of
performance possible to be shown by these buildings in case of an
earthquake was determined on the basis of the 4-grade performance
levels specified in Turkish Earthquake Code-2007 (TEC-2007). After
obtaining the 4-grade performance level, selected 23 parameters of
each building have been matched with the performance level. In this
stage, ANN-based fast evaluation algorithm mentioned above made
an economic and rapid evaluation of four to ten storey RC buildings.
According to the study, the prediction accuracy of ANN has been
found about 74%.
Abstract: This paper presents the influence of the vertical
seismic component on the non-linear dynamics analysis of three
different structures. The subject structures were analyzed and
designed according to recent codes. This paper considers three types
of buildings: 5-, 10-, and 15-story buildings. The non-linear dynamics
analysis of the structures with assuming elastic-perfectly-plastic
behavior was performed using RAM PERFORM-3D software; the
horizontal component was taken into consideration with and without
the incorporation of the corresponding vertical component. Dynamic
responses obtained for the horizontal component acting alone were
compared with those obtained from the simultaneous application of
both seismic components. The results show that the effect of the
vertical component of ground motion may increase the axial load
significantly in the interior columns and, consequently, the stories.
The plastic mechanisms would be changed. The P-Delta effect is
expected to increase. The punching base plate shear of the columns
should be considered. Moreover, the vertical component increases the
input energy when the structures exhibit inelastic behavior and are
taller.
Abstract: This paper presents a novel algorithm for modeling
photovoltaic based distributed generators for the purpose of optimal
planning of distribution networks. The proposed algorithm utilizes
sequential Monte Carlo method in order to accurately consider the
stochastic nature of photovoltaic based distributed generators. The
proposed algorithm is implemented in MATLAB environment and
the results obtained are presented and discussed.
Abstract: Fiber Reinforced Polymer (FRP) is a composite material with exceptional properties that are capable to replace conventional steel reinforcement in reinforced and pre-stressed concrete structures. However, the main obstacle for their wide use in pre-stressed concrete application is the anchorage system. Due to the weakness of FRP in the transverse direction, the pre-stressing capacity of FRP bars are limited. This paper investigates the modification of the conventional wedge anchorage system to be used for stressing of FRP bars in pre-stressed applications. Epoxy adhesive material with glass FRP (GFRP) bars and conventional steel wedge were used in this paper. The GFRP bars are encased with epoxy at the anchor zone and the wedge system was used in pull-out test. The results showed a loading capacity of 47.6 kN which is 69% of the bar ultimate capacity. Additionally, nylon wedge was made with the same dimensions of the steel wedge and tested for GFRP bars without epoxy layer. The nylon wedge showed a loading capacity of 19.7 kN which is only 28.5% of the ultimate bar capacity.
Abstract: In an attempt to investigate the performance of single
basin solar still for climate conditions of Ludhiana a single basin
solar still was designed, fabricated and tested. The energy balance
equations for various parts of the still are solved by Gauss-Seidel
iteration method. Computer model was made and experimentally
validated. The validated computer model was used to estimate the
annual distillation yield and performance ratio of the still for
Ludhiana. The Theoretical and experimental distillation yield were
4318.79 ml and 3850 ml respectively for the typical day. The
predicted distillation yield was 12.5% higher than the experimental
yield. The annual distillation yield per square metre aperture area and
annual performance ratio for single basin solar still is 1095 litres and
0.43 respectively. The payback period for micro-stepped solar still is
2.5 years.
Abstract: The properties of hollow sandcrete blocks produced in
Minna, Nigeria are presented. Sandcrete block is made of cement,
water and sand binded together in certain mix proportions. For the
purpose of this work, fifty (50) commercial sandcrete block industries
were visited in Minna, Nigeria to obtain block samples and
aggregates used for the manufacture, and to take inventory of the mix
composition and the production process. Sieve analysis tests were
conduction on the soil sample from various block industries to
ascertain their quality to be used for block making. The mix ratios
were also investigated. Five (5) nine inches (9’’ or 225mm) blocks
were obtained from each block industry and tested for dimensional
compliance and compressive strength. The results of the soil test
shows that the grading fall within the limit for natural aggregate and
can easily are used to obtain workable mix. Physical examinations of
the block sizes show slight deviation from the standard requirement
in NIS 87:2000. Compressive strength of hollow sandcrete blocks in
range of 0.12 N/mm2 to 0.54 N/mm2 was obtained which is below the
recommendable value of 3.45 N/mm2 for load bearing hollow
sandcrete blocks. This indicates that these blocks are below the
standard for load-bearing sandcrete blocks and cannot be used as load
bearing walling units. The mix composition also indicated low
cement content resulting in low compressive strength. Most of the
commercial block industries visited does not take curing very serious.
Water were only sprinkled ones or twice before the blocks were
stacked and made readily available for sale. It is recommended that a
mix ratio of 1:4 to 1:6 should be used for the production of sandcrete
blocks and proper curing practice should be adhered. Blocks should
also be cured for 14 days before making them available for
consumers.
Abstract: It is the patient compliance and stability in
combination with controlled drug delivery and biocompatibility that
forms the core feature in present research and development of
sustained biodegradable patch formulation intended for wound
healing. The aim was to impart sustained degradation, sterile
formulation, significant folding endurance, elasticity,
biodegradability, bio-acceptability and strength. The optimized
formulation comprised of polymers including Hydroxypropyl methyl
cellulose, Ethylcellulose, and Gelatin, and Citric Acid PEG Citric
acid (CPEGC) triblock dendrimers and active Curcumin. Polymeric
mixture dissolved in geometric order in suitable medium through
continuous stirring under ambient conditions. With continued stirring
Curcumin was added with aid of DCM and Methanol in optimized
ratio to get homogenous dispersion. The dispersion was sonicated
with optimum frequency and for given time and later casted to form a
patch form. All steps were carried out under strict aseptic conditions.
The formulations obtained in the acceptable working range were
decided based on thickness, uniformity of drug content, smooth
texture and flexibility and brittleness. The patch kept on stability
using butter paper in sterile pack displayed folding endurance in
range of 20 to 23 times without any evidence of crack in an
optimized formulation at room temperature (RT) (24 ± 2°C). The
patch displayed acceptable parameters after stability study conducted
in refrigerated conditions (8±0.2°C) and at RT (24 ± 2°C) up to 90
days. Further, no significant changes were observed in critical
parameters such as elasticity, biodegradability, drug release and drug
content during stability study conducted at RT 24±2°C for 45 and 90
days. The drug content was in range 95 to 102%, moisture content
didn’t exceeded 19.2% and patch passed the content uniformity test.
Percentage cumulative drug release was found to be 80% in 12h and
matched the biodegradation rate as drug release with correlation
factor R2>0.9. The biodegradable patch based formulation developed
shows promising results in terms of stability and release profiles.
Abstract: The present study aims to investigate the performance
of Moringa oleifera seed extract as natural coagulant in clarification
of secondary wastewater treatment plant (MWWTP) located in East
of Algiers, Algeria. Coagulation flocculation performance of
Moringa oleifera was evaluated through supernatant residual
turbidity after jar test trials. Various influence parameters namely
Moringa oleifera dosage and pH have been considered. Tests on
Reghaia wastewater, having 129 NTU of initial turbidity, showed a
removal of 69.45% of residual turbidity with only 1.5 mg/l of
Moringa oleifera. This sufficient removal capability encourages the
use of this bioflocculant for treatment of turbid waters. Indeed,
Moringa oleifera which is a natural resource available locally (South
of Algeria) coupled to the non-toxicity, biocompatibility and
biodegradability, may be a very interesting alternative to the
conventional coagulants used so far.
Abstract: This study was carried out for an underground subway station at Seoul Metro, Korea. The optimal set-points of the ventilation control system are determined every 3 hours, then, the ventilation controller adjusts the ventilation fan speed according to the optimal set-point changes. Compared to manual ventilation system which is operated irrespective of the OAQ, the IDP-based ventilation control system saves 3.7% of the energy consumption. Compared to the fixed set-point controller which is operated irrespective of the IAQ diurnal variation, the IDP-based controller shows better performance with a 2% decrease in energy consumption, maintaining the comfortable IAQ range inside the station.
Abstract: Electrostatic interaction energy (ΔEEDL) is a part of the Extended Derjaguin-Landau-Verwey-Overbeek (XDLVO) theory, which, together with van der Waals (ΔEVDW) and acid base (ΔEAB) interaction energies, has been extensively used to investigate the initial adhesion of bacteria to surfaces. Electrostatic or electrical double layer interaction energy is considerably affected by surface potential; however it cannot be determined experimentally and is usually replaced by zeta (ζ) potential via electrophoretic mobility. This paper focusses on the effect of ionic concentration as a function of pH and the effect of mineral grain size on ζ potential. It was found that both ionic strength and mineral grain size play a major role in determining the value of ζ potential for the adhesion of P. putida to hematite and quartz surfaces. Higher ζ potential values lead to higher electrostatic interaction energies and eventually to higher total XDLVO interaction energy resulting in bacterial repulsion.
Abstract: The fuel potential of six tropical hardwood species
namely: Triplochiton scleroxylon, Ceiba pentandra, Aningeria
robusta, Terminalia superba, Celtis mildbreadii and Piptadenia
africana were studied. Properties studied included species density,
gross calorific value, volatile matter, ash content, organic carbon and
elemental composition. Fuel properties were determined using
standard laboratory methods. The result indicates that the gross
calorific value (GCV) of the species ranged from 20.16 to 22.22
MJ/kg and they slightly varied from each other. Additionally, the
GCV of the biomass materials were higher than that of other biomass
materials like; wheat straw, rice straw, maize straw and sugar cane.
The ash and volatile matter content varied from 0.6075 to 5.0407%,
and 75.23% to 83.70% respectively. The overall rating of the
properties of the six biomass materials suggested that Piptadenia
africana has the best fuel property to be used as briquettes and
Aningeria robusta the worse. This study therefore suggests that a
holistic assessment of a biomass material needs to be done before
selecting it for fuel purpose.
Abstract: The present research investigated whether gender
differences affect performance in a simple math quiz in statistics
course. Participants of this study comprised a sample of 567 statistics
students in two different universities in Lebanon. Data were collected
through a simple math quiz. Analysis of quantitative data indicated
that there wasn’t a significant difference in math performance
between males and females. The results suggest that improvements in
student performance may depend on improved mastery of basic
algebra especially for females. The implications of these findings and
further recommendations were discussed.
Abstract: This study aimed to explore the practical experience
of child welfare caseworkers and professionalism in child case
management in Malaysia. This paper discussed the specific social
work practice competency and the challenges faced by child
caseworkers in the fieldwork. This research was qualitative with
grounded theory approach. Four sessions of focused group discussion
(FGD) were conducted involving a total of 27 caseworkers (child
protector and probation officers) in the Klang Valley. The study
found that the four basic principles of knowledge in child case
management namely: 1. knowledge in child case management; 2.
professional values of caseworkers towards children; 3. skills in
managing cases; and 4. culturally competent practice in child case
management. In addition, major challenges faced by the child case
manager are the capacity and commitment of the family in children’s
rehabilitation program, the credibility of caseworkers are being
challenged, and the challenges of support system from intra and interagency.
This study is important for policy makers to take into account
the capacity and the needs of the child’s caseworker in accordance
with the national social work competency framework. It is expected
that case management services for children will improve
systematically in line with national standards.
Abstract: In this paper, to model a real life wind turbine, a
probabilistic approach is proposed to model the dynamics of the
blade elements of a small axial wind turbine under extreme stochastic
wind speeds conditions. It was found that the power and the torque
probability density functions even-dough decreases at these extreme
wind speeds but are not infinite. Moreover, we also fund that it
is possible to stabilize the power coefficient (stabilizing the output
power)above rated wind speeds by turning some control parameters.
This method helps to explain the effect of turbulence on the quality
and quantity of the harness power and aerodynamic torque.
Abstract: The research aims to study the association between
job satisfaction, motivation and the five factors of organizational
citizenship behavior (i.e. Altruism, Conscientiousness,
Sportsmanship, Courtesy and Civic virtue) among Public Sector
Employees in Pakistan. In this research Structure Equation Modeling
with confirmatory factor analysis was used to test the relationship
between two independent and five dependent variables. Data was
collected through questionnaire survey from 152 Public Servants
Working in Gujrat District-Pakistan in different capacities. Stratified
Random Sampling Technique was used to conduct this survey. The
results of the study indicate that five factors of OCB have positive
significant relation with both motivation and job satisfaction except
the relationship of Civic Virtue with Motivation. The research
findings implicate that factors other than motivation and job
satisfaction may also affect OCB. Likewise, all the five factors of
OCB may not be present in all populations. Thus, Managers must
concentrate on increasing motivation and job satisfaction to increase
OCB. Furthermore, the present research gives a direction to future
researchers to use more independent variables (e.g. Culture,
leadership, workplace environment, various job attitudes, types of
motivation, etc.) on different types of populations with larger sample
size in order to find the reasons behind insignificant relationship of
civic virtue with Motivation in the research in hand and to generalize
the tested model.
Abstract: Passive control methods can be utilized to build
earthquake resistant structures, and also to strengthen the vulnerable
ones. In this paper, we studied the effect of this system in increasing
the ductility and energy dissipation and also modeled the behavior of
this type of eccentric bracing, and compared the hysteresis diagram
of the modeled samples with the laboratory samples. We studied
several samples of frames with vertical shear-links in order to assess
the behavior of this type of eccentric bracing. Each of these samples
was modeled in finite element software ANSYS 9.0, and was
analyzed under the static cyclic loading. It was found that vertical
shear-links have a more stable hysteresis loops. Another analysis
showed that using honeycomb beams as the horizontal beam along
with steel reinforcement has no negative effect on the hysteresis
behavior of the sample.
Abstract: In this paper, the notion of rank−k numerical range
of rectangular complex matrix polynomials are introduced. Some
algebraic and geometrical properties are investigated. Moreover, for
Є > 0, the notion of Birkhoff-James approximate orthogonality
sets for Є−higher rank numerical ranges of rectangular matrix
polynomials is also introduced and studied. The proposed definitions
yield a natural generalization of the standard higher rank numerical
ranges.
Abstract: This paper describes the collection and analysis of
data obtained from face-to-face interviews conducted in selected
Libyan industrial companies. The objectives of the interviews are to
enhance understanding, and generate explanations of current issues in
culture and quality management systems in Libyan companies. The
method used in analyzing the questions, as well as the main finding
of each question are explained. The interviews probed areas identify
national and organizational culture, quality management systems,
current methods, effects, barriers and other factors affecting the
success of quality management implementation. Eleven questions are
prepared and been discussed with the interviewees.
Abstract: The current paper presents the results of a conducted
case study. During the past few years the number of children
diagnosed with Learning Difficulties has drastically augmented and
especially the cases of ADHD (Attention Deficit Hyperactivity
Disorder). One of the core characteristics of ADHD is a deficit in
working memory functions. The review of the literature indicates a
plethora of educational software that aim at training and enhancing
the working memory. Nevertheless, in the current paper, the
possibility of using for the same purpose free, online games will be
explored. Another issue of interest is the potential effect of the
working memory training to the core symptoms of ADHD. In order
to explore the abovementioned research questions, three digital tests
are employed, all of which are developed on the E-slate platform by
the author, in order to check the levels of ADHD’s symptoms and to
be used as diagnostic tools, both in the beginning and in the end of
the case study. The tools used during the main intervention of the
research are free online games for the training of working memory.
The research and the data analysis focus on the following axes: a) the
presence and the possible change in two of the core symptoms of
ADHD, attention and impulsivity and b) a possible change in the
general cognitive abilities of the individual. The case study was
conducted with the participation of a thirteen year-old, female
student, diagnosed with ADHD, during after-school hours. The
results of the study indicate positive changes both in the levels of
attention and impulsivity. Therefore, we conclude that the training of
working memory through the use of free, online games has a positive
impact on the characteristics of ADHD. Finally, concerning the
second research question, the change in general cognitive abilities, no
significant changes were noted.
Abstract: Numerous investigations suggest that Mesenchymal
Stem Cells (MSCs) in general represent a valuable tool for therapy of
symptoms related to chronic inflammatory diseases. Blue Horizon
Stem Cell Therapy Program is a leading provider of adult and
children’s stem cell therapies. Uniquely we have safely and
efficiently treated more than 600 patients with documenting each
procedure. The purpose of our study is primarily to monitor the
immune response in order to validate the safety of intravenous
infusion of human umbilical cord blood derived MSCs (UC-MSCs),
and secondly, to evaluate effects on biomarkers associated with
chronic inflammation. Nine patients were treated for conditions
associated with chronic inflammation and for the purpose of antiaging.
They have been given one intravenous infusion of UCMSCs.
Our study of blood test markers of 9 patients with chronic
inflammation before and within three months after MSCs treatment
demonstrates that there is no significant changes and MSCs treatment
was safe for the patients. Analysis of different indicators of chronic
inflammation and aging included in initial, 24-hours, two weeks and
three months protocols showed that stem cell treatment was safe for
the patients; there were no adverse reactions. Moreover data from
follow up protocols demonstrates significant improvement in energy
level, hair, nails growth and skin conditions. Intravenously
administered UC-MSCs were safe and effective in the improvement
of symptoms related to chronic inflammation. Further close
monitoring and inclusion of more patients are necessary to fully
characterize the advantages of UC-MSCs application in treatment of
symptoms related to chronic inflammation.