Abstract: The load frequency control problem of power systems has attracted a lot of attention from engineers and researchers over the years. Increasing and quickly changing load demand, coupled with the inclusion of more generators with high variability (solar and wind power generators) on the network are making power systems more difficult to regulate. Frequency changes are unavoidable but regulatory authorities require that these changes remain within a certain bound. Engineers are required to perform the tricky task of adjusting the control system to maintain the frequency within tolerated bounds. It is well known that to minimize frequency variations, a large proportional feedback gain (speed regulation constant) is desirable. However, this improvement in performance using proportional feedback comes about at the expense of a reduced stability margin and also allows some steady-state error. A conventional PI controller is then included as a secondary control loop to drive the steadystate error to zero. In this paper, we propose a robust controller to replace the conventional PI controller which guarantees performance and stability of the power system over the range of variation of the speed regulation constant. Simulation results are shown to validate the superiority of the proposed approach on a simple single-area power system model.
Abstract: Green house effect has becomes a serious concern in
many countries due to the increase consumption of the fossil fuel.
There have been many studies to find an alternative power source.
Wind energy found to be one of the most useful solutions to help in
overcoming the air pollution and global. There is no agreed solution
to conversion of wind energy to electrical energy. In this paper, the
advantages of using a Switched Reluctance Generator (SRG) for
wind energy applications. The theoretical study of the self excitation
of a SRG and the determination of the variable parameters in a SRG
design are discussed. The design parameters for the maximum power
output of the SRG are computed using Matlab simulation. The
designs of the circuit to control the variable parameters in a SRG to
provide the maximum power output are also discussed.
Abstract: Wind power is among the most actively developing distributed generation (DG) technology. Majority of the wind power based DG technologies employ wind turbine induction generators (WTIG) instead of synchronous generators, for the technical advantages like: reduced size, increased robustness, lower cost, and increased electromechanical damping. However, dynamic changes of wind speed make the amount of active/reactive power injected/drawn to a WTIG embedded distribution network highly variable. This paper analyzes the effect of wind speed changes on the active and reactive power penetration to the wind energy embedded distribution network. Four types of wind speed changes namely; constant, linear change, gust change and random change of wind speed are considered in the analysis. The study is carried out by three-phase, non-linear, dynamic simulation of distribution system component models. Results obtained from the investigation are presented and discussed.
Abstract: This paper focuses on PSS/E modeling of wind farms
of Doubly-fed Induction Generator (DFIG) type and their impact on
issues of power system operation. Since Wind Turbine Generators
(WTG) don-t have the same characteristics as synchronous
generators, the appropriate modeling of wind farms is essential for
transmission system operators to analyze the best options of
transmission grid reinforcements as well as to evaluate the wind
power impact on reliability and security of supply. With the high
excepted penetration of wind power into the power system a
simultaneous loss of Wind Farm generation will put at risk power
system security and reliability. Therefore, the main wind grid code
requirements concern the fault ride through capability and frequency
operation range of wind turbines. In case of grid faults wind turbines
have to supply a definite reactive power depending on the
instantaneous voltage and to return quickly to normal operation.
Abstract: In this paper is study the possibility of successfully
implementing of hollow roller concept in order to minimize inertial
mass of the large bearings, with major results in diminution of the
material consumption, increasing of power efficiency (in wind power
station area), increasing of the durability and life duration of the large
bearings systems, noise reduction in working, resistance to
vibrations, an important diminution of losses by abrasion and
reduction of the working temperature. In this purpose was developed
an original solution through which are reduced mass, inertial forces
and moments of large bearings by using of hollow rollers. The
research was made by using the method of finite element analysis
applied on software type Solidworks - Nastran. Also, is study the
possibility of rapidly changing the manufacturing system of solid and
hollow cylindrical rollers.