Abstract: s the floating offshore wind turbine industry continues to develop and grow, the capabilities of established port facilities need to be assessed as to their ability to support the expanding construction and installation requirements. This paper assesses current infrastructure requirements and projected changes to port facilities that may be required to support the floating offshore wind industry. Understanding the infrastructure needs of the floating offshore renewable industry will help to identify the port-related requirements. Floating offshore wind turbines can be installed further out to sea and in deeper waters than traditional fixed offshore wind arrays, meaning it can take advantage of stronger winds. Separate ports are required for substructure construction, fit-out of the turbines, moorings, subsea cables and maintenance. Large areas are required for the laydown of mooring equipment, inter array cables, turbine blades and nacelles. The capabilities of established port facilities to support floating wind farms are assessed by evaluation of size of substructures, height of wind turbine with regards to the cranes for fitting of blades, distance to offshore site and offshore installation vessel characteristics. The paper will discuss the advantages and disadvantages of using large land based cranes, inshore floating crane vessels or offshore crane vessels at the fit-out port for the installation of the turbine. Water depths requirements for import of materials and export of the completed structures will be considered. There are additional costs associated with any emerging technology. However, part of the popularity of Floating Offshore Wind Turbines stems from the cost savings against permanent structures like fixed wind turbines. Floating Offshore Wind Turbine developers can benefit from lighter, more cost effective equipment which can be assembled in port and towed to site rather than relying on large, expensive installation vessels to transport and erect fixed bottom turbines. The ability to assemble Floating Offshore Wind Turbines equipment on shore means minimising highly weather dependent operations like offshore heavy lifts and assembly, saving time and costs and reducing safety risks for offshore workers. Maintenance might take place in safer onshore conditions for barges and semi submersibles. Offshore renewables, such as floating wind, can take advantage of this wealth of experience, while oil and gas operators can deploy this experience at the same time as entering the renewables space. The floating offshore wind industry is in the early stages of development and port facilities are required for substructure fabrication, turbine manufacture, turbine construction and maintenance support. The paper discusses the potential floating wind substructures as this provides a snapshot of the requirements at the present time, and potential technological developments required for commercial development. Scaling effects of demonstration-scale projects will be addressed; however the primary focus will be on commercial-scale (30+ units) device floating wind energy farms.
Abstract: Turbocharger is a device that is driven by the turbine and increases efficiency and power output of the engine by forcing external air into the combustion chamber. This study focused on the distribution of stress on the turbine blades and total deformation that may occur during its working along with turbocharger to carry out its static structural analysis of turbine blades. Structural steel was selected as the material for turbocharger. Assembly of turbocharger and turbine blades was designed on PRO ENGINEER. Furthermore, the structural analysis is performed by using ANSYS. This research concluded that by using structural steel, the efficiency of engine is improved and by increasing number of turbine blades, more waste heat from combustion chamber is emitted.
Abstract: A new mathematical model for calculating the temperature field of the profile part of the cooled blades of gas turbines is developed. The theoretical substantiation of the method is based on the application of the method of potential theory (the method of boundary integral equations). The effectiveness of the implementation of the developed mathematical model is confirmed on the basis of a computational experiment.
Abstract: Present study investigates the effect of unsteady wakes on heat transfer in blade tip. Heat/mass transfer was measured in blade tip region depending on a variety of strouhal number by naphthalene sublimation technique. Naphthalene sublimation technique measures heat transfer using a heat/mass transfer analogy. Experiments are performed in linear cascade which is composed of five turbine blades and rotating rods. Strouhal number of inlet flow are changed ranging from 0 to 0.22. Reynolds number is 100,000 based on 11.4 m/s of outlet flow and axial chord length. Three different squealer tip geometries such as base squealer tip, vertical rib squealer tip, and camber line squealer tip are used to study how unsteady wakes affect heat transfer on a blade tip. Depending on squealer tip geometry, different flow patterns occur on a blade tip. Also, unsteady wakes cause reduced tip leakage flow and turbulent flow. As a result, as strouhal number increases, heat/mass transfer coefficients decrease due to the reduced leakage flow. As strouhal number increases, heat/ mass transfer coefficients on a blade tip increase in vertical rib squealer tip.
Abstract: A novel Active Flap System (AFS) has been developed
at DTU Wind Energy, as a result of a 3-year R&D project following
almost 10 years of innovative research in this field. The full scale AFS
comprises an active deformable trailing edge has been tested at the
unique rotating test facility at the Risø Campus of DTU Wind Energy
in Denmark. The design and instrumentation of the wing section and
the AFS are described. The general description and objectives of the
rotating test rig at the Risø campus of DTU are presented, along
with an overview of sensors on the setup and the test cases. The
post-processing of data is discussed and results of steady, flap step
and azimuth control flap cases are presented.
Abstract: In this article, a method is presented to effectively
estimate the deformed shape of a thick plate due to line heating. The
method uses a fifth order spline interpolation, with up to C3
continuity at specific points to compute the shape of the deformed
geometry. First and second order derivatives over a surface are the
resulting parameters of a given heating line on a plate. These
parameters are determined through experiments and/or finite element
simulations. Very accurate kriging models are fitted to real or virtual
surfaces to build-up a database of maps. Maps of first and second
order derivatives are then applied on numerical plate models to
evaluate their evolving shapes through a sequence of heating lines.
Adding an optimization process to this approach would allow
determining the trajectories of heating lines needed to shape complex
geometries, such as Francis turbine blades.
Abstract: Transportation of long turbine blades from one place
to another is a difficult process. Hence a feasibility study of
modularization of wind turbine blade was taken from structural
standpoint through finite element analysis. Initially, a non-segmented
blade is modeled and its structural behavior is evaluated to serve as
reference. The resonant, static bending and fatigue tests are simulated
in accordance with IEC61400-23 standard for comparison purpose.
The non-segmented test blade is separated at suitable location based
on trade off studies and the segments are joined with an innovative
double strap bonded joint configuration. The adhesive joint is
modeled by adopting cohesive zone modeling approach in ANSYS.
The developed blade model is analyzed for its structural response
through simulation. Performances of both the blades are found to be
similar, which indicates that, efficient segmentation of the long blade
is possible which facilitates easy transportation of the blades and on
site reassembling. The location selected for segmentation and
adopted joint configuration has resulted in an efficient segmented
blade model which proves the methodology adopted for segmentation
was quite effective. The developed segmented blade appears to be the
viable alternative considering its structural response specifically in
fatigue within considered assumptions.
Abstract: Wind energy is one of the clean renewable energy. However, the low frequency (20-200HZ) noise generated from the wind turbine blades, which bothers the residents, becomes the major problem to be developed. It is useful for predicting the aerodynamic noise by flow field and pressure distribution analysis on the wind turbine blades. Therefore, the main objective of this study is to use different turbulence models to analyze the flow field and pressure distributions of the wing blades.
Three-dimensional Computation Fluid Dynamics (CFD) simulation of the flow field was used to calculate the flow phenomena for the National Renewable Energy Laboratory (NREL) Phase VI horizontal axis wind turbine rotor. Two different flow cases with different wind speeds were investigated: 7m/s with 72rpm and 15m/s with 72rpm.
Four kinds of RANS-based turbulence models, Standard k-ε, Realizable k-ε, SST k-ω, and v2f, were used to predict and analyze the results in the present work. The results show that the predictions on pressure distributions with SST k-ω and v2f turbulence models have good agreements with experimental data.
Abstract: Developments in turbine cooling technology play an important role in increasing the thermal efficiency and the power output of recent gas turbines, in particular the turbojets.
Advanced turbojets operate at high temperatures to improve thermal efficiency and power output. These temperatures are far above the permissible metal temperatures. Therefore, there is a critical need to cool the blades in order to give theirs a maximum life period for safe operation.
The focused objective of this work is to calculate the turbojet performances, as well as the calculation of turbine blades cooling.
The developed application able the calculation of turbojet performances to different altitudes in order to find a point of optimal use making possible to maintain the turbine blades at an acceptable maximum temperature and to limit the local variations in temperatures in order to guarantee their integrity during all the lifespan of the engine.
Abstract: Among the various cooling processes in industrial
applications such as: electronic devices, heat exchangers, gas
turbines, etc. Gas turbine blades cooling is the most challenging one.
One of the most common practices is using ribbed wall because of
the boundary layer excitation and therefore making the ultimate
cooling. Vortex formation between rib and channel wall will result in
a complicated behavior of flow regime. At the other hand, selecting
the most efficient method for capturing the best results comparing to
experimental works would be a fascinating issue. In this paper 4
common methods in turbulence modeling: standard k-e, rationalized
k-e with enhanced wall boundary layer treatment, k-w and RSM
(Reynolds stress model) are employed to a square ribbed channel to
investigate the separation and thermal behavior of the flow in the
channel. Finally all results from different methods which are used in
this paper will be compared with experimental data available in
literature to ensure the numerical method accuracy.
Abstract: This paper presents a study of laminar to turbulent transition on a profile specifically designed for wind turbine blades, the DU91-W2-250, which belongs to a class of wind turbine dedicated airfoils, developed by Delft University of Technology. A comparison between the experimental behavior of the airfoil studied at Delft wind tunnel and the numerical predictions of the commercial CFD solver ANSYS FLUENT® has been performed. The prediction capabilities of the Spalart-Allmaras turbulence model and of the γ-θ Transitional model have been tested. A sensitivity analysis of the numerical results to the spatial domain discretization has also been performed using four different computational grids, which have been created using the mesher GAMBIT®. The comparison between experimental measurements and CFD results have allowed to determine the importance of the numerical prediction of the laminar to turbulent transition, in order not to overestimate airfoil friction drag due to a fully turbulent-regime flow computation.
Abstract: The present work deals with the structural analysis of
turbine blades and modeling of turbine blades. A common failure
mode for turbine machines is high cycle of fatigue of compressor and
turbine blades due to high dynamic stresses caused by blade vibration
and resonance within the operation range of the machinery. In this
work, proper damping system will be analyzed to reduce the
vibrating blade. The main focus of the work is the modeling of under
platform damper to evaluate the dynamic analysis of turbine-blade
vibrations. The system is analyzed using Bond graph technique. Bond
graph is one of the most convenient ways to represent a system from
the physical aspect in foreground. It has advantage of putting together
multi-energy domains of a system in a single representation in a
unified manner. The bond graph model of dry friction damper is
simulated on SYMBOLS-shakti® software. In this work, the blades
are modeled as Timoshenko beam. Blade Vibrations under different
working conditions are being analyzed numerically.
Abstract: A new mechanism responsible for structural life
consumption due to resonant fatigue in turbine blades, or vanes, is
presented and explained. A rotating blade or vane in a gas turbine can
change its contour due to erosion and/or material build up, in any of
these instances, the surface pressure distribution occurring on the
suction and pressure sides of blades-vanes can suffer substantial
modification of their pressure and temperatures envelopes and flow
characteristics. Meanwhile, the relative rotation between the blade
and duct vane while the pressurized gas flows and the consequent
wake crossings, will induce a fluctuating thrust force or lift that will
excite the blade.
An actual totally used up set of vane-blade components in a HP
turbine power stage in a gas turbine is analyzed. The blade suffered
some material erosion mostly at the trailing edge provoking a
peculiar surface pressure envelope which evolved as the relative
position between the vane and the blade passed in front of each other.
Interestingly preliminary modal analysis for this eroded blade
indicates several natural frequencies within the aeromechanic power
spectrum, moreover, the highest frequency component is 94% of one
natural frequency indicating near resonant condition.
Independently of other simultaneously occurring fatigue cycles
(such as thermal, centrifugal stresses).
Abstract: A series of experiments were carried out to study
unsteady behavior of the flow field as well as the boundary layer of
an airfoil oscillating in plunging motion in a subsonic wind tunnel.
The measurements involved surface pressure distribution
complimented with surface-mounted hot-films. The effect of leadingedge
roughness that simulates surface irregularities on the wind
turbine blades was also studied on variations of aerodynamic loads
and boundary layer behavior.
Abstract: The present study is concerned with the effect of
exciting boundary layer on cooling process in a gas-turbine blades.
The cooling process is numerically investigated. Observations show
cooling the first row of moving or stable blades leads to increase
their life-time. Results show that minimum temperature in cooling
line with exciting boundary layer is lower than without exciting.
Using block in cooling line of turbines' blade causes flow pattern and
stability in boundary layer changed that causes increase in heat
transfer coefficient. Results show at the location of block,
temperature of turbines' blade is significantly decreased. The k-ε
turbulence model is used.
Abstract: In contrast to existing of calculation of temperature field of a profile part a blade with convective cooling which are not taking into account multi connective in a broad sense of this term, we develop mathematical models and highly effective combination (BIEM AND FDM) numerical methods from the point of view of a realization on the PC. The theoretical substantiation of these methods is proved by the appropriate theorems.