Abstract: Long number multiplications (n ≥ 128-bit) are a
primitive in most cryptosystems. They can be performed better by
using Karatsuba-Ofman technique. This algorithm is easy to
parallelize on workstation network and on distributed memory, and
it-s known as the practical method of choice. Multiplying long
numbers using Karatsuba-Ofman algorithm is fast but is highly
recursive. In this paper, we propose different designs of
implementing Karatsuba-Ofman multiplier. A mixture of sequential
and combinational system design techniques involving pipelining is
applied to our proposed designs. Multiplying large numbers can be
adapted flexibly to time, area and power criteria. Computationally
and occupation constrained in embedded systems such as: smart
cards, mobile phones..., multiplication of finite field elements can be
achieved more efficiently. The proposed designs are compared to
other existing techniques. Mathematical models (Area (n), Delay (n))
of our proposed designs are also elaborated and evaluated on
different FPGAs devices.
Abstract: In this paper, a fiber based Fabry-Perot interferometer
is proposed and demonstrated for a non-contact displacement
measurement. A piece of micro-prism which attached to the
mechanical vibrator is served as the target reflector. Interference
signal is generated from the superposition between the sensing beam
and the reference beam within the sensing arm of the fiber sensor.
This signal is then converted to the displacement value by using a
developed program written in visual Cµ programming with a
resolution of λ/8. A classical function generator is operated for
controlling the vibrator. By fixing an excitation frequency of 100 Hz
and varying the excitation amplitude range of 0.1 – 3 Volts, the
output displacements measured by the fiber sensor are obtained from
1.55 μm to 30.225 μm. A reference displacement sensor with a
sensitivity of ~0.4 μm is also employed for comparing the
displacement errors between both sensors. We found that over the
entire displacement range, a maximum and average measurement
error are obtained of 0.977% and 0.44% respectively.
Abstract: The development and application of wind power for
renewable energy has attracted growing interest in recent years. Renewable energy sources are attracting much alteration as they can
reduce both environmental damage and dependence on fossil fuels. With the growing need for sustainable energy supplies, a case is made
for decentralized, stand-alone power supplies (SAPS) as an alternative to power grids. In the era which traditional petroleum energy resource
decreasing and the green house affect significant increasing, the development and usage of regenerative resources is inevitable. Due to the contribution of the pioneers, the development of regenerative resources already has a remarkable achievement; however, in the view of economy and quantity, it is still a long road for regenerative energy
to replace traditional petroleum energy. In our prospective, in stead of
investigate larger regenerative energy equipment, it is much wiser to
think about the blind side and breakthrough of the current technique.
Abstract: Motion control of flexible arms is more difficult than
that of rigid arms, however utilizing its dynamics enables improved
performance such as a fast motion in short operation time. This paper
investigates a ball throwing robot with one rigid link and one flexible
link. This robot throws a ball at a set speed with a proper control torque.
A mathematical model of this ball throwing robot is derived through
Hamilton’s principle. Several patterns of torque input are designed and
tested through the proposed simulation models. The parameters of
each torque input pattern is optimized and determined by chaos
embedded vector evaluated particle swarm optimization (CEVEPSO).
Then, the residual vibration of the manipulator after throwing is
suppressed with input shaping technique. Finally, a real experiment is
set up for the model checking.
Abstract: Accurate evaluation of damping ratios involving soilstructure interaction (SSI) effects is the prerequisite for seismic design of in-situ buildings. This study proposes a combined approach to identify damping ratios of SSI systems based on ambient excitation technique. The proposed approach is illustrated with main test process, sampling principle and algorithm steps through an engineering example, as along with its feasibility and validity. The proposed approach is employed for damping ratio identification of 82 buildings in Xi-an, China. Based on the experimental data, the variation range and tendency of damping ratios of these SSI systems, along with the preliminary influence factor, are shown and discussed. In addition, a fitting curve indicates the relation between the damping ratio and fundamental natural period of SSI system.
Abstract: The focal spot of a high intensity focused ultrasound
transducer is small. To heat a large target volume, multiple treatment spots are required. If the power of each treatment spot is fixed, it could
results in insufficient heating of initial spots and over-heating of later ones, which is caused by the thermal diffusion. Hence, to produce a
uniform heated volume, the delivered energy of each treatment spot
should be properly adjusted. In this study, we proposed an iterative, extrapolation technique to adjust the required ultrasound energy of
each treatment spot. Three different scanning pathways were used to evaluate the performance of this technique. Results indicate that by using the proposed technique, uniform heating volume could be obtained.
Abstract: The information revealed by derivatives can help to
better characterize digital near-end crosstalk signatures with the
ultimate goal of identifying the specific aggressor signal.
Unfortunately, derivatives tend to be very sensitive to even low
levels of noise. In this work we approximated the derivatives of both
quiet and noisy digital signals using a wavelet-based technique. The
results are presented for Gaussian digital edges, IBIS Model digital
edges, and digital edges in oscilloscope data captured from an actual
printed circuit board. Tradeoffs between accuracy and noise
immunity are presented. The results show that the wavelet technique
can produce first derivative approximations that are accurate to
within 5% or better, even under noisy conditions. The wavelet
technique can be used to calculate the derivative of a digital signal
edge when conventional methods fail.
Abstract: Recently, as the scale of construction projects has
increases, more ground excavation for foundations is carried out than ever before. Consequently, damage to underground ducts (gas, water/sewage or oil pipelines, communication cables or power cable ducts) or superannuated pipelines frequently cause serious accidents
resulting in damage to life and property. (In Korea, the total length of city water pipelines was approximately 2,000 km as of the end of 2009.) In addition, large amounts of damage caused by fractures, water
and gas leakage caused by superannuation or damage to underground
ducts in construction has been reported. Therefore, a system is required to precisely detect defects and deterioration in underground
pipelines and the locations of such defects, for timely and accurate
maintenance or replacement of the ducts. In this study, a system was
developed which can locate underground structures (gas and water
pipelines, power cable ducts, etc.) in 3D-coordinates and monitor the
degree and position of defects using an Inertial Measurement Unit
(IMU) sensing technique. The system can prevent damage to underground ducts and superannuated pipelines during construction,
and provide reliable data for maintenance. The utility of the IMU sensing technique used in aircraft and ships in civil applications was
verified.
Abstract: In this paper some results on strict stability heve beeb extended for fuzzy differential equations with impulse effect using Lyapunov functions and Razumikhin technique.
Abstract: Herein, we report the different types of surface morphology due to the interaction between the pure protein Insulin (INS) and catanionic surfactant mixture of Sodium Dodecyl Sulfate (SDS) and Cetyl Trimethyl Ammonium Bromide (CTAB) at air/water interface obtained by the Langmuir-Blodgett (LB) technique. We characterized the aggregations by Scanning Electron Microscopy (SEM), Atomic Force Microscopy (AFM) and Fourier transform infrared spectroscopy (FTIR) in LB films. We found that the INS adsorption increased in presence of catanionic surfactant at air/water interface. The presence of small amount of surfactant induces two-stage growth kinetics due to the pure protein absorption and protein-catanionic surface micelle interaction. The protein remains in native state in presence of small amount of surfactant mixture. Smaller amount of surfactant mixture with INS is producing surface micelle type structure. This may be considered for drug delivery system. On the other hand, INS becomes unfolded and fibrillated in presence of higher amount of surfactant mixture. In both the cases, the protein was successfully immobilized on a glass substrate by the LB technique. These results may find applications in the fundamental science of the physical chemistry of surfactant systems, as well as in the preparation of drug-delivery system.
Abstract: Addition of milli or micro sized particles to the heat
transfer fluid is one of the many techniques employed for improving
heat transfer rate. Though this looks simple, this method has
practical problems such as high pressure loss, clogging and erosion
of the material of construction. These problems can be overcome by
using nanofluids, which is a dispersion of nanosized particles in a
base fluid. Nanoparticles increase the thermal conductivity of the
base fluid manifold which in turn increases the heat transfer rate.
Nanoparticles also increase the viscosity of the basefluid resulting in
higher pressure drop for the nanofluid compared to the base fluid. So
it is imperative that the Reynolds number (Re) and the volume
fraction have to be optimum for better thermal hydraulic
effectiveness. In this work, the heat transfer enhancement using
aluminium oxide nanofluid using low and high volume fraction
nanofluids in turbulent pipe flow with constant wall temperature has
been studied by computational fluid dynamic modeling of the
nanofluid flow adopting the single phase approach. Nanofluid, up till
a volume fraction of 1% is found to be an effective heat transfer
enhancement technique. The Nusselt number (Nu) and friction factor
predictions for the low volume fractions (i.e. 0.02%, 0.1 and 0.5%)
agree very well with the experimental values of Sundar and Sharma
(2010). While, predictions for the high volume fraction nanofluids
(i.e. 1%, 4% and 6%) are found to have reasonable agreement with
both experimental and numerical results available in the literature.
So the computationally inexpensive single phase approach can be
used for heat transfer and pressure drop prediction of new nanofluids.
Abstract: In this paper, we start by first characterizing the most
important and distinguishing features of wavelet-based watermarking
schemes. We studied the overwhelming amount of algorithms
proposed in the literature. Application scenario, copyright protection
is considered and building on the experience that was gained,
implemented two distinguishing watermarking schemes. Detailed
comparison and obtained results are presented and discussed. We
concluded that Joo-s [1] technique is more robust for standard noise
attacks than Dote-s [2] technique.
Abstract: The operation performance of a valveless micro-pump
is strongly dependent on the shape of connected nozzle/diffuser and
Reynolds number. The aims of present work are to compare the
performance curves of micropump with the original straight
nozzle/diffuser and contoured nozzle/diffuser under different back
pressure conditions. The tested valveless micropumps are assembled
of five pieces of patterned PMMA plates with hot-embracing
technique. The structures of central chamber, the inlet/outlet
reservoirs and the connected nozzle/diffuser are fabricated with laser
cutting machine. The micropump is actuated with circular-type PZT
film embraced on the bottom of central chamber. The deformation of
PZT membrane with various input voltages is measured with a
displacement laser probe. A simple testing facility is also constructed
to evaluate the performance curves for comparison.
In order to observe the evaluation of low Reynolds number
multiple vortex flow patterns within the micropump during suction
and pumping modes, the unsteady, incompressible laminar
three-dimensional Reynolds-averaged Navier-Stokes equations are
solved. The working fluid is DI water with constant thermo-physical
properties. The oscillating behavior of PZT film is modeled with the
moving boundary wall in way of UDF program. With the dynamic
mesh method, the instants pressure and velocity fields are obtained
and discussed.Results indicated that the volume flow rate is not
monotony increased with the oscillating frequency of PZT film,
regardless of the shapes of nozzle/diffuser. The present micropump
can generate the maximum volume flow rate of 13.53 ml/min when
the operation frequency is 64Hz and the input voltage is 140 volts.
The micropump with contoured nozzle/diffuser can provide 7ml/min
flow rate even when the back pressure is up to 400 mm-H2O. CFD
results revealed that the flow central chamber was occupied with
multiple pairs of counter-rotating vortices during suction and
pumping modes. The net volume flow rate over a complete
oscillating periodic of PZT
Abstract: The flash memory has many advantages such as low power consumption, strong shock resistance, fast I/O and non-volatility. And it is increasingly used in the mobile storage device. The YAFFS, one of the NAND flash file system, is widely used in the embedded device. However, the existing YAFFS takes long time to mount the file system because it scans whole spare areas in all pages of NAND flash memory. In order to solve this problem, we propose a new content-based flash file system using a mounting time reduction technique. The proposed method only scans partial spare areas of some special pages by using content-based block management. The experimental results show that the proposed method reduces the average mounting time by 87.2% comparing with JFFS2 and 69.9% comparing with YAFFS.
Abstract: This paper studies the mean square exponential synchronization problem of a class of stochastic neutral type chaotic neural networks with mixed delay. On the Basis of Lyapunov stability theory, some sufficient conditions ensuring the mean square exponential synchronization of two identical chaotic neural networks are obtained by using stochastic analysis and inequality technique. These conditions are expressed in the form of linear matrix inequalities (LMIs), whose feasibility can be easily checked by using Matlab LMI Toolbox. The feedback controller used in this paper is more general than those used in previous literatures. One simulation example is presented to demonstrate the effectiveness of the derived results.
Abstract: This study assessed the effects of climate change on
Thai soybeans under simulation situations. Our study is focused on
temperature variability and effects on growth, yield, and genetic
changes in 2 generations of Chiang Mai 60 cultivars. In the
experiment, soybeans were exposed to 3 levels of air temperature for
8 h day-1 in an open top chamber for 2 cropping periods. Air
temperature levels in each treatment were controlled at 30-33°C (±
2.3) for LT-treatment, 33-36°C ( ± 2.4) for AT-treatment, and 36-40
°C ( ± 3.2) for HT-treatment, respectively. Positive effects of high
temperature became obvious at the maturing stage when yield
significantly increased in both cropping periods. Results in growth
indicated that shoot length at the pre-maturing stage
(V3-R3) was more positively affected by high temperature than at the
maturing stage. However, the positive effect on growth under high
temperature was not found in the 2nd cropping period. Finally, genetic
changes were examined in phenotype characteristics by the AFLPs
technique. The results showed that the high temperature factor clearly
caused genetic change in the soybeans and showed more alteration in
the 2nd cropping period.
Abstract: ZnO-SnO2 i.e. Zinc-Tin-Oxide (ZTO) thin films were
deposited on glass substrate with varying concentrations (ZnO:SnO2
- 100:0, 90:10, 70:30 and 50:50 wt.%) at room temperature by flash
evaporation technique. These deposited ZTO film were annealed at
450 0C in vacuum. These films were characterized to study the effect
of annealing on the structural, electrical, and optical properties.
Atomic force microscopy (AFM) and Scanning electron microscopy
(SEM) images manifest the surface morphology of these ZTO thin
films. The apparent growth of surface features revealed the formation
of nanostructure ZTO thin films. The small value of surface
roughness (root mean square RRMS) ensures the usefulness in
optical coatings. The sheet resistance was also found to be decreased
for both types of films with increasing concentration of SnO2. The
optical transmittance found to be decreased however blue shift has
been observed after annealing.
Abstract: Titanium gels doped with water-soluble cationic porphyrin were synthesized by the sol–gel polymerization of Ti (OC4H9)4. In this work we investigate the spectroscopic properties along with SEM images of tetra carboxyl phenyl porphyrin when incorporated into porous matrix produced by the sol–gel technique.
Abstract: In this paper, we propose ablock-wise watermarking scheme for color image authentication to resist malicious tampering of digital media. The thresholding technique is incorporated into the scheme such that the tampered region of the color image can be recovered with high quality while the proofing result is obtained. The watermark for each block consists of its dual authentication data and the corresponding feature information. The feature information for recovery iscomputed bythe thresholding technique. In the proofing process, we propose a dual-option parity check method to proof the validity of image blocks. In the recovery process, the feature information of each block embedded into the color image is rebuilt for high quality recovery. The simulation results show that the proposed watermarking scheme can effectively proof the tempered region with high detection rate and can recover the tempered region with high quality.
Abstract: The aim of the current study is to develop a numerical
tool that is capable of achieving an optimum shape and design of
hyperbolic cooling towers based on coupling a non-linear finite
element model developed in-house and a genetic algorithm
optimization technique. The objective function is set to be the
minimum weight of the tower. The geometric modeling of the tower
is represented by means of B-spline curves. The finite element
method is applied to model the elastic buckling behaviour of a tower
subjected to wind pressure and dead load. The study is divided into
two main parts. The first part investigates the optimum shape of the
tower corresponding to minimum weight assuming constant
thickness. The study is extended in the second part by introducing the
shell thickness as one of the design variables in order to achieve an
optimum shape and design. Design, functionality and practicality
constraints are applied.