Abstract: This paper presents results of compressive strength,
capillary water absorption, and density tests conducted on concrete
containing recycled aggregate (RCA) which is obtained from
structural waste generated by the construction industry in Turkey. In
the experiments, 0%, 15%, 30%, 45% and 60% of the normal
(natural) coarse aggregate was replaced by the recycled aggregate.
Maximum aggregate particle sizes were selected as 16 mm, 22,4 mm
and 31,5 mm; and 0,06%, 0,13% and 0,20% of air-entraining agent
(AEA) were used in mixtures. Fly ash and superplasticizer were used
as a mineral and chemical admixture, respectively. The same type
(CEM I 42.5) and constant dosage of cement were used in the study.
Water/cement ratio was kept constant as 0.53 for all mixture. It was
concluded that capillary water absorption, compressive strength, and
density of concrete decreased with increasing RCA ratio. Increasing
in maximum aggregate particle size and amount of AEA also affect
the properties of concrete significantly.
Abstract: It is the worldwide problem that the recycled PVB is
not recycled and it is wildly stored in landfills. However, PVB has
similar chemical properties such as PVC. Moreover, both of these
polymers are plasticized. Therefore, the study of thermal properties
of plasticized PVC and the recycled PVB obtained by recycling of
windshields is carried out. This work has done in order to find nondegradable
processing conditions applicable for both polymers.
Tested PVC contained 38% of plasticizer diisononyl phthalate
(DINP) and PVB was plasticized with 28% of triethylene glycol,
bis(2-ethylhexanoate) (3GO). The thermal and thermo-oxidative
decomposition of both vinyl polymers are compared by calorimetric
analysis and by tensile strength analysis.
Abstract: The secondary alloy A226 is used for many
automotive casting produced by mould casting and high pressure die
casting. This alloy has excellent castability, good mechanical
properties and cost-effectiveness. Production of primary aluminium
alloys belong to heavy source fouling of life environs. The European
Union calls for the emission reduction and reduction in energy
consumption therefore increase production of recycled (secondary)
aluminium cast alloys. The contribution is deal with influence of
recycling on the quality of the casting made from A226 in automotive
industry. The properties of the casting made from secondary
aluminium alloys were compared with the required properties of
primary aluminium alloys. The effect of recycling on microstructure
was observed using combination different analytical techniques (light
microscopy upon black-white etching, scanning electron microscopy
- SEM upon deep etching and energy dispersive X-ray analysis -
EDX). These techniques were used for the identification of the
various structure parameters, which was used to compare secondary
alloy microstructure with primary alloy microstructure.
Abstract: This paper is aimed to the use of different types of
industrial wastes in concrete production. From examined waste
(crushed concrete waste) our tested concrete samples with dimension
150 mm were prepared. In these samples, fractions 4/8 mm and 8/16
mm by recycled concrete aggregate with a range of variation from 0
to 100% were replaced. Experiment samples were tested for
compressive strength after 2, 7, 14 and 28 days of hardening.
From obtained results it is evident that all samples prepared with
washed recycled concrete aggregates met the requirement of standard
for compressive strength of 20 MPa already after 14 days of
hardening. Sample prepared with recycled concrete aggregates (4/8
mm: 100% and 8/16 mm: 60%) reached 101% of compressive
strength value (34.7 MPa) after 28 days of hardening in comparison
with the reference sample (34.4 MPa). The lowest strength after 28
days of hardening (27.42 MPa) was obtained for sample consisting of
recycled concrete in proportion of 40% for 4/8 fraction and 100% for
8/16 fraction of recycled concrete.
Abstract: The model tests were conducted in the laboratory
without and with Plastic recycled polymer in fly ash steep slopes
overlaying soft foundation soils like fly ash and powai soil in order to
check the stability of steep slope. In this experiment, fly ash is used
as a filling material and Plastic Recycled Polymers of diameter =
3mm and length = 4mm were made from waste plastic product (lower
grade plastic product). The properties of fly ash and Plastic recycled
polymers are determined. From the experiments, load and settlement
have measured. From these data, load –settlement curves have
reported. It has been observed from test results that load carrying
capacity of mixture fly ash with Plastic Recycled Polymers slope is
more than that of fly ash slope. The deformation of Plastic Recycled
Polymers slope is slightly more than that of fly ash slope. A Finite
Element Method (F.E.M.) was also evaluated using PLAXIS 3D
version. The failure pattern, deformations and factor of safety are
reported based on analytical programme. The results from
experimental data and analytical programme are compared and
reported.
Abstract: The thermal performance of a solar water heating with
1.00 m2 flat plate collectors in Cascavel - PR, is which presented in
this article, paper presents the solution to leverage the marketing of
solar heating systems through detailed constituent materials of the
solar collector studies, these abundant materials in construction, such
as expanded polyethylene, PVC, aluminum and glass tubes, mixing
them with new materials to minimize loss of efficiency while
decreasing its cost. The system was tested during months and the
collector obtained maximum recorded temperature of outlet fluid of
55°C, while the maximum temperature of the water at the bottom of
the hot water tank was 35°C. The average daily energy collected was
19.6 MJ/d; the energy supplied by the solar plate was 16.2 MJ/d; the
loss in the feed pipe was 3.2 MJ/d; the solar fraction was 32.2%, the
efficiency of the collector was 45.6% and the efficiency of the system
was 37.8%.
Abstract: Sustainability and eco-friendly requirement of
engineering materials are sort for in recent times, thus giving rise to
the development of bio-composites. However, the natural fibres to
matrix interface interactions remain a key issue in getting the desired
mechanical properties from such composites. Treatment of natural
fibres is essential in improving matrix to filler adhesion, hence
improving its mechanical properties. In this study, investigations
were carried out to determine the effect of sodium hydroxide
treatment on the tensile, flexural, impact and hardness properties of
crushed and uncrushed Luffa cylindrica fibre reinforced recycled low
density polyethylene composites. The LC (Luffa cylindrica) fibres
were treated with 0%, 2%, 4%, 6%, 8% and 10% wt. sodium
hydroxide (NaOH) concentrations for a period of 24 hours under
room temperature conditions. A formulation ratio of 80/20 g (matrix
to reinforcement) was maintained for all developed samples. Analysis
of the results showed that the uncrushed luffa fibre samples gave
better mechanical properties compared with the crushed luffa fibre
samples. The uncrushed luffa fibre composites had a maximum
tensile and flexural strength of 7.65 MPa and 17.08 Mpa respectively
corresponding to a young modulus and flexural modulus of 21.08
MPa and 232.22 MPa for the 8% and 4% wt. NaOH concentration
respectively. Results obtained in the research showed that NaOH
treatment with the 8% NaOH concentration improved the mechanical
properties of the LC fibre reinforced composites when compared with
other NaOH treatment concentration values.
Abstract: This work is focused on the study of valuation of
recycled concrete aggregates, by measuring certain properties of
concrete in the fresh and hardened state. In this study, rheological
tests and physic-mechanical characterization on concretes and
mortars were conducted with recycled concrete whose geometric
properties were identified aggregates. Mortars were elaborated with
recycled fine aggregate (0/5mm) and concretes were manufactured
using recycled coarse aggregates (5/12.5 mm and 12.5/20 mm). First,
a study of the mortars was conducted to determine the effectiveness
of polycarboxylate superplasticizer on the workability of these and
their action deflocculating of the recycled sand. The rheological
behavior of mortars based on fine aggregate recycled was
characterized. The results confirm that the mortars composed of
different fractions of recycled sand (0 /5) have a better mechanical
properties (compressive and flexural strength) compared to normal
mortar. Also, the mechanical strengths of concretes made with
recycled aggregates (5/12.5 mm and 12.5/20 mm), are comparable to
those of conventional concrete with conventional aggregates,
provided that the implementation can be improved by the addition of
a superplasticizer.
Abstract: The paper a summary of the results of concretes with
partial substitution of natural aggregates with recycled concrete is
solved. Design formulas of the concretes were characterised with 20,
40 and 60% substitution of natural 8-16mm fraction aggregates with
a selected recycled concrete of analogous coarse fractions. With the
product samples an evaluation of coarse fraction aggregates influence
on fresh concrete consistency and concrete strength in time was
carried out. The results of concretes with aggregates substitution will
be compared to reference formula containing only the fractions of
natural aggregates.
Abstract: In the near future, companies will be increasingly forced to shift their activities along a new road in order to decrease the harmful effects of their design, production and after-life on our environment. Products must meet environmental standards to not only prevent penalties but to consider the sustainability for future generations. However, the most important factor that companies will face is selecting a reasonable strategy to maximize their profit. Thus, companies need to have precise forecast from their profit after design stage through Trade-off analysis. This paper is an attempt to introduce a mathematical model that considers effective factors that impact the total profit when products are designed for resource and energy efficiency or recyclability. The modification is according to different strategies based on a Cost-Volume-Profit model. Here, the cost structure consists of Recycling cost, Development cost, Ramp-up cost, Production cost, and Pollution cost. Also, the model shows the effect of implementation of design for recyclable on revenue structure through revenue of used parts and revenue of recycled materials. A numerical example is used to evaluate the proposed model. Results show that fulfillment of Green Product Development not only can reduce the environmental impact of products but also it will increase profit of company in long term.
Abstract: The paper is focused on testing of the poly(vinyl butyral) (PVB) layer which had the function of a CO2 insulating protection against concrete and mortar carbonation. The barrier efficiency of PVB was verified by the measurement of diffusion characteristics. Two different types of PVB were tested; original extruded PVB sheet and PVB sheet made from PVB dispersion which was obtained from recycled windshields. The work deals with the testing CO2 diffusion when polymer sheets were exposed to a CO2 atmosphere (10% v/v CO2) with 0% RH. The excellent barrier capability against CO2 permeability of original and also recycled types of PVB layers was observed. This application of PVB waste can bring advantageous use in civil engineering and significant environmental contribution.
Abstract: The aim of this work is to use an environmental, cheap; organic non-traditional admixture to improve the structural behavior of sustainable reinforced concrete beams contains different ratios of recycled concrete aggregate. The used admixture prepared by using wastes from vegetable oil industry. Under and over reinforced concrete beams made from natural aggregate and different ratios of recycled concrete aggregate were tested under static load until failure. Eight beams were tested to investigate the performance and mechanism effect of admixture on improving deformation characteristics, modulus of elasticity and toughness of tested beams. Test results show efficiency of organic admixture on improving flexural behavior of beams contains 20% recycled concrete aggregate more over the other ratios.
Abstract: Construction industry in Greece consumes annually
more than 25 million tons of natural aggregates originating mainly
from quarries. At the same time, more than 2 million tons of
construction and demolition waste are deposited every year, usually
without control, therefore increasing the environmental impact of this
sector. A potential alternative for saving natural resources and
minimize landfilling, could be the recycling and re-use of Concrete
and Demolition Waste (CDW) in concrete production. Moreover, in
order to conform to the European legislation, Greece is obliged to
recycle non-hazardous construction and demolition waste to a
minimum of 70% by 2020. In this paper characterization of recycled
materials - commercially and laboratory produced, coarse and fine,
Recycled Concrete Aggregates (RCA) - has been performed. Namely,
X-Ray Fluorescence and X-ray diffraction (XRD) analysis were used
for chemical and mineralogical analysis respectively. Physical
properties such as particle density, water absorption, sand equivalent
and resistance to fragmentation were also determined. This study,
first time made in Greece, aims at outlining the differences between
RCA and natural aggregates and evaluating their possible influence
in concrete performance. Results indicate that RCA’s chemical
composition is enriched in Si, Al, and alkali oxides compared to
natural aggregates. X-ray diffraction (XRD) analyses results
indicated the presence of calcite, quartz and minor peaks of mica and
feldspars. From all the evaluated physical properties of coarse RCA,
only water absorption and resistance to fragmentation seem to have a
direct influence on the properties of concrete. Low Sand Equivalent
and significantly high water absorption values indicate that fine
fractions of RCA cannot be used for concrete production unless
further processed. Chemical properties of RCA in terms of water
soluble ions are similar to those of natural aggregates. Four different
concrete mixtures were produced and examined, replacing natural
coarse aggregates with RCA by a ratio of 0%, 25%, 50% and 75%
respectively. Results indicate that concrete mixtures containing
recycled concrete aggregates have a minor deterioration of their
properties (3-9% lower compression strength at 28 days) compared to
conventional concrete containing the same cement quantity.
Abstract: Complex sensitivity analysis of stresses in a concrete slab of the real type of rigid pavement made from recycled materials is performed. The computational model of the pavement is designed as a spatial (3D) model, is based on a nonlinear variant of the finite element method that respects the structural nonlinearity, enables to model different arrangements of joints, and the entire model can be loaded by the thermal load. Interaction of adjacent slabs in joints and contact of the slab and the subsequent layer are modeled with the help of special contact elements. Four concrete slabs separated by transverse and longitudinal joints and the additional structural layers and soil to the depth of about 3m are modeled. The thickness of individual layers, physical and mechanical properties of materials, characteristics of joints, and the temperature of the upper and lower surface of slabs are supposed to be random variables. The modern simulation technique Updated Latin Hypercube Sampling with 20 simulations is used. For sensitivity analysis the sensitivity coefficient based on the Spearman rank correlation coefficient is utilized. As a result, the estimates of influence of random variability of individual input variables on the random variability of principal stresses s1 and s3 in 53 points on the upper and lower surface of the concrete slabs are obtained.
Abstract: Recycling steel building components is key to the sustainability of a structure’s end-of-life, as it is the most economical solution. In this paper the effects of usage of recycled steel material in tall buildings aspects are investigated.
Abstract: Australia is a country of some 7,700 million square kilometers with a population of about 22.6 million. At present water security is a major challenge for Australia. In some areas the use of water resources is approaching and in some parts it is exceeding the limits of sustainability. A focal point of proposed national water conservation programs is the recycling of both urban stormwater and treated wastewater. But till now it is not widely practiced in Australia, and particularly stormwater is neglected. In Australia, only 4% of stormwater and rainwater is recycled, whereas less than 1% of reclaimed wastewater is reused within urban areas. Therefore, accurately monitoring, assessing and predicting the availability, quality and use of this precious resource are required for better management. As stormwater is usually of better quality than untreated sewage or industrial discharge, it has better public acceptance for recycling and reuse, particularly for non-potable use such as irrigation, watering lawns, gardens, etc. Existing stormwater recycling practice is far behind of research and no robust technologies developed for this purpose. Therefore, there is a clear need for using modern technologies for assessing feasibility of stormwater harvesting and reuse. Numerical modeling has, in recent times, become a popular tool for doing this job. It includes complex hydrological and hydraulic processes of the study area. The hydrologic model computes stormwater quantity to design the system components, and the hydraulic model helps to route the flow through stormwater infrastructures. Nowadays water quality module is incorporated with these models. Integration of Geographic Information System (GIS) with these models provides extra advantage of managing spatial information. However for the overall management of a stormwater harvesting project, Decision Support System (DSS) plays an important role incorporating database with model and GIS for the proper management of temporal information. Additionally DSS includes evaluation tools and Graphical user interface. This research aims to critically review and discuss all the aspects of stormwater harvesting and reuse such as available guidelines of stormwater harvesting and reuse, public acceptance of water reuse, the scopes and recommendation for future studies. In addition to these, this paper identifies, understand and address the importance of modern technologies capable of proper management of stormwater harvesting and reuse.
Abstract: Waste of certain process can be the input source of
other sectors in order to reduce environmental pollution. Today there
are more and more solid wastes are generated, but only very small
amount of those are recycled. So, the threatening of environmental
pressure to public health is very serious. The methods considered for
the treatment of solid waste are biogas tanks or processing to make
animal feed and fertilizer, however, they did not perform well. An
alternative approach is growing mushrooms on waste residues. This
is regarded as an environmental friendly solution with potential
economical benefit. The substrate producers do their best to produce
quality substrate at low cost. Apart from other methods, this can be
achieved by employing biologically degradable wastes used as the
resource material component of the substrate. Mushroom growing is
a significant tool for the restoration, replenishment and remediation
of Earth’s overburdened ecosphere. One of the rational methods of
waste utilization involves locally available wastes. The present study
aims to find out the yield of mushroom grown on locally available
waste for free and to conserve our environment by recycling wastes.
Abstract: This study examined the properties of fresh and hardened concretes as influenced by the moisture state of the coarse recycled concrete aggregates (RCA) after surface treatment. Surface treatment was performed by immersing the coarse RCA in a calcium metasilicate (CM) solution. The treated coarse RCA was maintained in three controlled moisture states, namely, air-dried, oven-dried, and saturated surface-dried (SSD), prior to its use in a concrete mix. The physical properties of coarse RCA were evaluated after surface treatment during the first phase of the experiment to determine the density and the water absorption characteristics of the RCA. The second phase involved the evaluation of the slump, slump loss, density, and compressive strength of the concretes that were prepared with different proportions of natural and treated coarse RCA. Controlling the moisture state of the coarse RCA after surface treatment was found to significantly influence the properties of the fresh and hardened concretes.
Abstract: The development of new construction materials using
recycled plastic is important to both the construction and the plastic
recycling industries. Manufacturing of fibers from industrial or
postconsumer plastic waste is an attractive approach with such
benefits as concrete performance enhancement, and reduced needs
for land filling. The main objective of this study is to investigate the
effect of Plastic fibers obtained locally from recycled waste on plastic
shrinkage cracking of ordinary cement based mortar. Parameters
investigated include: fiber length ranging from 20 to 50mm, and fiber
volume fraction ranging from 0% to 1.5% by volume. The test results
showed significant improvement in crack arresting mechanism and
substantial reduction in the surface area of cracks for the mortar
reinforced with recycled plastic fibers compared to plain mortar.
Furthermore, test results indicated that there was a slight decrease in
compressive strength of mortar reinforced with different lengths and
contents of recycled fibers compared to plain mortar. This study
suggests that adding more than 1% of RP fibers to mortar, can be
used effectively for controlling plastic shrinkage cracking of cement
based mortar, and thus results in waste reduction and resources
conservation.
Abstract: The suitability of Newsprint and Kraft papers for the production of cement bonded ceiling board was investigated. Sample boards were produced from newsprint paper (100%), mixture of newsprint and Kraft paper (50:50) and Kraft paper (100%) at 1:1, 2:1 and 3:1 cement/paper mixing ratio respectively with 3% additive concentration of calcium chloride (CaCl2). Density, flexural and thickness swelling properties of the boards were investigated. The effects of paper type and mixing ratio on the physical and mechanical properties were also examined. The bending properties of the board which include Modulus of Elasticity (MOE) and Modulus of Rupture (MOR) increased linearly with increase in density. Modulus of rupture of boards increased as the density and mixing ratio increased. The thickness swelling property for the two paper types decreased as the board density and mixing ratio increased. Boards made from Kraft paper recorded higher strength values than the ones made from recycled newsprint paper while the mixture of kraft and newsprint papers had the best surface finish. The result of the study will help in managing the large quality of waste from paper converting/carton industry and that the ceiling boards produced could be installed with clout nails or used with suspended ceiling fittings.