Abstract: An experiment of vented gas explosions involving two
different cylinder vessel volumes (0.2 and 0.0065 m3) was reported,
with equivalence ratio (Φ) ranged from 0.3 to 1.6. Both vessels were
closed at the rear end and fitted at the other side with a circular
orifice plate that gives a constant vent coefficient (K =Av/V2/3) of
16.4. It was shown that end ignition gives higher overpressures than
central ignition, even though most of the published work on venting
uses central ignition. For propane and ethylene, it is found that rich
mixtures gave the highest overpressures and these mixtures are not
considered in current vent design guidance; which the guideline is
based on mixtures giving the maximum flame temperature. A strong
influence of the vessel volume at constant K was found for methane,
propane, ethylene and hydrogen-air explosions. It can be concluded
that self- acceleration of the flame, which is dependent on the
distance of a flame from the ignition and the ‘suction’ at the vent
opening are significant factors affecting the vent flow during
explosion development in vented gas explosion. This additional
volume influence on vented explosions is not taken into account in
the current vent design guidance.
Abstract: In order to investigate a PROX microreactor
performance, two-dimensional modeling of the reacting flow
between two parallel plates is performed through a finite volume
method using an improved SIMPLE algorithm. A three-step surface
kinetics including hydrogen oxidation, carbon monoxide oxidation
and water-gas shift reaction is applied for a Pt-Fe/γ-Al2O3 catalyst
and operating temperatures of about 100ºC. Flow pattern, pressure
field, temperature distribution, and mole fractions of species are
found in the whole domain for all cases. Also, the required reactive
length for removing carbon monoxide from about 2% to less than 10
ppm is found. Furthermore, effects of hydraulic diameter, wall
temperature, and inlet mole fraction of air and water are investigated
by considering carbon monoxide selectivity and conversion. It is
found that air and water addition may improve the performance of
the microreactor in carbon monoxide removal in such operating
conditions; this is in agreement with the pervious published results.
Abstract: The aim of this work is to investigate on the internalflow
patterns in a plate heat exchanger channel, which affect the
rate of sedimentation fouling on the heat transfer surface of the
plate heat exchanger. The research methodologies were the
computer simulation using Computational Fluid Dynamics (CFD)
and the experimental works. COMSOL MULTIPHYSICS™
Version 3.3 was used to simulate the velocity flow fields to verify
the low and high flow regions. The results from the CFD technique
were then compared with the images obtained from the
experiments in which the fouling test rig was set up with a singlechannel
plate heat exchanger to monitor the fouling of calcium
carbonate. Two parameters were varied i.e., the crossing angle of
the two plate: 55/55, 10/10, and 55/10 degree, and the fluid flow
rate at the inlet: 0.0566, 0.1132 and 0.1698 m/s. The type of plate
“GX-12" (the surface area 0.12 m2, the depth 2.9 mm, the width of
fluid flow 215 mm and the thickness of stainless plate of 0.5 mm)
was used in this study. The results indicated that the velocity
distribution for the case of 55/55 degree seems to be very well
organized when compared with the others. Also, an increase in the
inlet velocity resulted in the reduction of fouling rate on the surface
of plate heat exchangers.
Abstract: A real time image-guided electroplating system is
proposed in this paper. Unlike previous electroplating systems, instead
of using the intermittent mode to electroplate 500um long copper
specimen, a CCD camera and a motion controller are used to adjust
anode-cathode distance to obtain better results. Since the image of the
gap distance is highly deteriorated due to complex chemical-electrical
operation inside the electrolyte, to determine the gap distance, an
image processing algorithm is developed and mainly based on the
entropy and energy values. In addition, the color and incidence
direction of light source are also discussed to help the image process in
this paper. From the experiment results, the specimens created by the
proposed system show better structure, better uniformity and better
finishing surface compared to those by previous intermittent
electroplating setup.
Abstract: The aim of this paper is to study the oblique
stagnation point flow on vertical plate with uniform surface heat flux
in presence of magnetic field. Using Stream function, partial
differential equations corresponding to the momentum and energy
equations are converted into non-linear ordinary differential
equations. Numerical solutions of these equations are obtained using
Runge-Kutta Fehlberg method with the help of shooting technique.
In the present work the effects of striking angle, magnetic field
parameter, Grashoff number, the Prandtl number on velocity and heat
transfer characteristics have been discussed. Effect of above
mentioned parameter on the position of stagnation point are also
studied.
Abstract: A specially designed flat plate was mounted vertically
over the axial line in the wind tunnel of the Aerospace Department of
the Pusan National University. The plate is 2 m long, 0.8 m high and 8
cm thick. The measurements were performed in velocity range from
15 to 60 m/s. A sand paper turbulizer was placed close to the plate nose
to provide fully developed turbulent boundary layer over the most part
of the plate. Strain balances were mounted in the trailing part of the
plate to measure the skin friction drag over removable insertions of
0.55×0.25m2 size. A set of the insertions was designed and
manufactured: 3mm thick polished metal surface and three compliant
surfaces. The compliant surfaces were manufactured of a silicone
rubber Silastic® S2 (Dow Corning company). To modify the
viscoelastic properties of the rubber, its composition was varied: 90%
of the rubber + 10% catalyst (standard), 92.5% + 7.5% (weak), 85% +
15% (strong). Modulus of elasticity and the loss tangent were
measured accurately for these materials in the frequency range from
40 Hz to 3 KHz using the unique proposed technique.
Abstract: Deoxygenation of beef fat for the production of hydrogenated biodiesel is investigated in a high pressure continuous flow fixed bed reactor over palladium-supported mesoporous titania catalyst synthesized via a combined single-step sol-gel process with surfactant-assisted templating method (SATM). The catalyst possessed a mesoporous charactheristic with high surface area and narrow pore size distribution. The main products of all Pd/TiO2 catalysts are n-heptadecane (n-C17) and n-pentadecane (n-C15) resulting from decarbonylation reaction. Pd/TiO2 catalyst synthesized via a combined single-step sol-gel process with SATM (SSSG) gave higher activity and selectivity to the desired products when compared to IWI/SG-TiO2 and IWI/P25-TiO2, respectively. SSSG catalyst gave the average conversion up to 80-90 % and 80 % for the selectivity in diesel range hydrocarbons. This result may cause by the higher surface area and the ability in dispersion of palladium ion in mesoporous of TiO2 during sol-gel process.
Abstract: Multi-site damage (MSD) has been a challenge to
aircraft, civil and power plant structures. In real life components are subjected to cracking at many vulnerable locations such as the bolt
holes. However, we do not consider for the presence of multiple cracks. Unlike components with a single crack, these components are
difficult to predict. When two cracks approach one another, their
stress fields influence each other and produce enhancing or shielding effect depending on the position of the cracks. In the present study,
numerical studies on fracture analysis have been conducted by using
the developed code based on the modified virtual crack closure integral (MVCCI) technique and finite element analysis (FEA) software ABAQUS for computing SIF of plates with multiple cracks.
Various parametric studies have been carried out and the results have
been compared with literature where ever available and also with the solution, obtained by using ABAQUS. By conducting extensive
numerical studies expressions for SIF have been obtained for collinear cracks and non-aligned cracks.
Abstract: Retrieval image by shape similarity, given a template
shape is particularly challenging, owning to the difficulty to derive a
similarity measurement that closely conforms to the common
perception of similarity by humans. In this paper, a new method for the
representation and comparison of shapes is present which is based on
the shape matrix and snake model. It is scaling, rotation, translation
invariant. And it can retrieve the shape images with some missing or
occluded parts. In the method, the deformation spent by the template
to match the shape images and the matching degree is used to evaluate
the similarity between them.
Abstract: A model of vortex wake is suggested to determine the
induced power during animal hovering flight. The wake is modeled
by a series of equi-spaced rigid rectangular vortex plates, positioned
horizontally and moving vertically downwards with identical speeds;
each plate is generated during powering of the functionally wing
stroke. The vortex representation of the wake considered in the
current theory allows a considerable loss of momentum to occur. The
current approach accords well with the nature of the wingbeat since it
considers the unsteadiness in the wake as an important fluid
dynamical characteristic. Induced power in hovering is calculated as
the aerodynamic power required to generate the vortex wake system.
Specific mean induced power to mean wing tip velocity ratio is
determined by solely the normal spacing parameter (f) for a given
wing stroke amplitude. The current theory gives much higher specific
induced power estimate than anticipated by classical methods.
Abstract: Numerical analysis for the aerodynamic characteristics
of the WIG (wing-in ground effect) craft with highly cambered and
aspect ratio of one is performed to predict the ground effect for the
case of with- and without- lower-extension endplate. The analysis is
included varying angles of attack from 0 to10 deg. and ground
clearances from 5% of chord to 50%. Due to the ground effect, the lift
by rising in pressure on the lower surface is increased and the
influence of wing-tip vortices is decreased. These two significant
effects improve the lift-drag ratio. On the other hand, the endplate
prevents the high-pressure air escaping from the air cushion at the
wing tip and causes to increase the lift and lift-drag ratio further. It is
found from the visualization of computation results that two wing-tip
vortices are generated from each surface of the wing tip and their
strength are weak and diminished rapidly. Irodov-s criteria are also
evaluated to investigate the static height stability. The comparison of
Irodov-s criteria shows that the endplate improves the deviation of the
static height stability with respect to pitch angles and heights. As the
results, the endplate can improve the aerodynamic characteristics and
static height stability of wings in ground effect, simultaneously.
Abstract: This study aimed to detect and to identify the main
strains of airborne microorganisms present in the Shanghai Metro
system. Samples were collected using agar plates exposed to the air
and microorganisms were identified using catalase, plasma coagulase
and hymolytic analysis. The results show that the concentration of
mildew present within a newly opened metro line was significantly
higher than for other lines. Differences among underground and
elevated stations can be attributed to differences in passenger flow and
the environment surrounding the stations. Additionally, the
investigation indicated that bacteria reached maximum levels at
different times on weekdays and weekends. The bacteria in the Metro
stations were identified as primarily Gram positive, consisting mainly
of coagulase-negative staphylococcus strains (CNS).
Abstract: In this investigation Salicylic acid, Sulfosalicylic acid
and Acetyl salicylic acid were chosen as a sample for thin layer
chromatography (TLC) on silica gel plates. Bicarbonate buffer at
different pH containing different amounts of boric acid was applied
as mobile phase. Specific interaction of these substances with boric
acid has effect on Rf in thin layer chromatography. Regular and
similar trend was observed in variations of Rf for mentioned
compounds in TLC by altering of percentages of boric acid in mobile
phase in pH range of 8-10. Also effect of organic solvent, mixture of
water/ organic solvent and organic solvent containing boric acid as
mobile phase was studied.
Abstract: As nanotechnology advances, the use of nanotechnology for medical purposes in the field of nanomedicine seems more promising; the rise of nanorobots for medical diagnostics and treatments could be arriving in the near future. This study proposes a swarm intelligence based control mechanism for swarm nanorobots that operate as artificial platelets to search for wounds. The canonical particle swarm optimization algorithm is employed in this study. A simulation in the circulatory system is constructed and used for demonstrating the movement of nanorobots with essential characteristics to examine the performance of proposed control mechanism. The effects of three nanorobot capabilities including their perception range, maximum velocity and respond time are investigated. The results show that canonical particle swarm optimization can be used to control the early version nanorobots with simple behaviors and actions.
Abstract: Sputum smear conversion after one month of antituberculosis
therapy in new smear positive pulmonary tuberculosis
patients (PTB+) is a vital indicator towards treatment success. The
objective of this study is to determine the rate of sputum smear
conversion in new PTB+ patients after one month under treatment of
National Institute of Diseases of the Chest and Hospital (NIDCH).
Analysis of sputum smear conversion was done by re-clinical
examination with sputum smear microscopic test after one month.
Socio-demographic and hematological parameters were evaluated to
perceive the correlation with the disease status. Among all enrolled
patients only 33.33% were available for follow up diagnosis and of
them only 42.86% patients turned to smear negative. Probably this
consequence is due to non-coherence to the proper disease
management. 66.67% and 78.78% patients reported low haemoglobin
and packed cell volume level respectively whereas 80% and 93.33%
patients accounted accelerated platelet count and erythrocyte
sedimentation rate correspondingly.
Abstract: Fuel and oxidant gas delivery plate, or fuel cell
plate, is a key component of a Proton Exchange Membrane (PEM)
fuel cell. To manufacture low-cost and high performance fuel cell
plates, advanced computer modeling and finite element structure
analysis are used as virtual prototyping tools for the optimization
of the plates at the early design stage. The present study examines
thermal stress analysis of the fuel cell plates that are produced
using a patented, low-cost fuel cell plate production technique
based on screen-printing. Design optimization is applied to
minimize the maximum stress within the plate, subject to strain
constraint with both geometry and material parameters as design
variables. The study reveals the characteristics of the printed
plates, and provides guidelines for the structure and material design
of the fuel cell plate.
Abstract: Biometric techniques are gaining importance for
personal authentication and identification as compared to the
traditional authentication methods. Biometric templates are
vulnerable to variety of attacks due to their inherent nature. When a
person-s biometric is compromised his identity is lost. In contrast to
password, biometric is not revocable. Therefore, providing security
to the stored biometric template is very crucial. Crypto biometric
systems are authentication systems, which blends the idea of
cryptography and biometrics. Fuzzy vault is a proven crypto
biometric construct which is used to secure the biometric templates.
However fuzzy vault suffer from certain limitations like nonrevocability,
cross matching. Security of the fuzzy vault is affected
by the non-uniform nature of the biometric data. Fuzzy vault when
hardened with password overcomes these limitations. Password
provides an additional layer of security and enhances user privacy.
Retina has certain advantages over other biometric traits. Retinal
scans are used in high-end security applications like access control to
areas or rooms in military installations, power plants, and other high
risk security areas. This work applies the idea of fuzzy vault for
retinal biometric template. Multimodal biometric system
performance is well compared to single modal biometric systems.
The proposed multi modal biometric fuzzy vault includes combined
feature points from retina and fingerprint. The combined vault is
hardened with user password for achieving high level of security.
The security of the combined vault is measured using min-entropy.
The proposed password hardened multi biometric fuzzy vault is
robust towards stored biometric template attacks.
Abstract: This paper proposed a stiffness analysis method for a
3-PRS mechanism for welding thick aluminum plate using FSW
technology. In the molding process, elastic deformation of lead-screws
and links are taken into account. This method is based on the virtual
work principle. Through a survey of the commonly used stiffness
performance indices, the minimum and maximum eigenvalues of the
stiffness matrix are used to evaluate the stiffness of the 3-PRS
mechanism. Furthermore, A FEA model has been constructed to verify
the method. Finally, we redefined the workspace using the stiffness
analysis method.
Abstract: An alarming emergence of multidrug-resistant strains
of the tuberculosis pathogen Mycobacterium tuberculosis and
continuing high worldwide incidence of tuberculosis has invigorated
the search for novel drug targets. The enzyme glutamate racemase
(MurI) in bacteria catalyzes the stereoconversion of L-glutamate to
D-glutamate which is a component of the peptidoglycan cell wall of
the bacterium. The inhibitors targeted against MurI from several
bacterial species have been patented and are advocated as promising
antibacterial agents. However there are none available against MurI
from Mycobacterium tuberculosis, due to the lack of its threedimensional
structure. This work accomplished two major objectives.
First, the tertiary structure of MtMurI was deduced computationally
through homology modeling using the templates from bacterial
homologues. It is speculated that like in other Gram-positive bacteria,
MtMurI exists as a dimer and many of the protein interactions at the
dimer interface are also conserved. Second, potent candidate
inhibitors against MtMurI were identified through docking against
already known inhibitors in other organisms.
Abstract: In this work, the plate bending formulation of the boundary element method - BEM, based on the Reissner?s hypothesis, is extended to the analysis of plates reinforced by beams taking into account the membrane effects. The formulation is derived by assuming a zoned body where each sub-region defines a beam or a slab and all of them are represented by a chosen reference surface. Equilibrium and compatibility conditions are automatically imposed by the integral equations, which treat this composed structure as a single body. In order to reduce the number of degrees of freedom, the problem values defined on the interfaces are written in terms of their values on the beam axis. Initially are derived separated equations for the bending and stretching problems, but in the final system of equations the two problems are coupled and can not be treated separately. Finally are presented some numerical examples whose analytical results are known to show the accuracy of the proposed model.