Abstract: To reflect the influence of after-treatment system retrofit and natural gas-fueled vehicle replace on exhaust emissions emitted by urban buses, a portable emission measurement system (PEMS) was employed herein to conduct real driving emission measurements. This study investigated the differences in particle number (PN), particle mass (PM), and nitrogen oxides (NOx) emissions from a China IV diesel bus retrofitted by catalyzed diesel particulate filter (CDPF), a China IV diesel bus, and a China V natural gas bus. The results show that both tested diesel buses possess markedly advantages in NOx emission control when compared to the lean-burn natural gas bus equipped without any NOx after-treatment system. As to PN and PM, only the DOC+CDPF retrofitting diesel bus exhibits enormous benefits on emission control related to the natural gas bus, especially the normal diesel bus. Meanwhile, the differences in PM and PN emissions between retrofitted and normal diesel buses generally increase with the increase in vehicle specific power (VSP). Furthermore, the differences in PM emissions, especially those in the higher VSP ranges, are more significant than those in PN. In addition, the maximum peak PN particle size (32 nm) of the retrofitted diesel bus was significantly lower than that of the normal diesel bus (100 nm). These phenomena indicate that the CDPF retrofitting can effectively reduce diesel bus exhaust particle emissions, especially those with large particle sizes.
Abstract: Petroleum refining is a chemical process in which the raw material (crude oil) is converted to finished commercial products for end users. The fluid catalytic cracking (FCC) unit is a key asset in refineries, requiring optimised processes in the context of engineering design. Following the first stage of separation of crude oil in a distillation tower, an additional 40 per cent quantity is attainable in the gasoline pool with further conversion of the downgraded product of crude oil (residue from the distillation tower) using a catalyst in the FCC process. Effective removal of sulphur oxides, nitrogen oxides, carbon and heavy metals from FCC gasoline requires greater separation efficiency and involves an enormous environmental significance. The FCC unit is primarily a reactor and regeneration system which employs cyclone systems for separation. Catalyst losses in FCC cyclones lead to high particulate matter emission on the regenerator side and fines carryover into the product on the reactor side. This paper aims at demonstrating the importance of FCC unit design criteria in terms of technical performance and compliance with environmental legislation. A systematic review of state-of-the-art FCC technology was carried out, identifying its key technical challenges and sources of emissions. Case studies of petroleum refineries in Nigeria were assessed against selected global case studies. The review highlights the need for further modelling investigations to help improve FCC design to more effectively meet product specification requirements while complying with stricter environmental legislation.
Abstract: Selective catalytic reduction systems for nitrogen oxides reduction by ammonia has been the chosen technology by most of diesel vehicle (i.e. bus and truck) manufacturers in Brazil, as also in Europe. Furthermore, at some conditions, over-stoichiometric ammonia availability is also needed that increases the NH3 slips even more. Ammonia (NH3) by this vehicle exhaust aftertreatment system provides a maximum efficiency of NOx removal if a significant amount of NH3 is stored on its catalyst surface. In the other words, the practice shows that slightly less than 100% of the NOx conversion is usually targeted, so that the aqueous urea solution hydrolyzes to NH3 via other species formation, under relatively low temperatures. This paper presents a model based on neural networks integrated with a road vehicle simulator that allows to estimate NH3-slip emission factors for different driving conditions and patterns. The proposed model generates high NH3slips which are not also limited in Brazil, but more efforts needed to be made to elucidate the contribution of vehicle-emitted NH3 to the urban atmosphere.
Abstract: Current trends in the building industry are oriented towards the reduction of maintenance costs and the ecological benefits of buildings or building materials. Surface treatment of building materials with photocatalytic active titanium dioxide added into concrete can offer a good solution in this context. Architectural concrete has one disadvantage – dust and fouling keep settling on its surface, diminishing its aesthetic value and increasing maintenance e costs. Concrete surface – silicate material with open porosity – fulfils the conditions of effective photocatalysis, in particular, the self-cleaning properties of surfaces. This modern material is advantageous in particular for direct finishing and architectural concrete applications. If photoactive titanium dioxide is part of the top layers of road concrete on busy roads and the facades of the buildings surrounding these roads, exhaust fumes can be degraded with the aid of sunshine; hence, environmental load will decrease. It is clear that options for removing pollutants like nitrogen oxides (NOx) must be found. Not only do these gases present a health risk, they also cause the degradation of the surfaces of concrete structures. The photocatalytic properties of titanium dioxide can in the long term contribute to the enhanced appearance of surface layers and eliminate harmful pollutants dispersed in the air, and facilitate the conversion of pollutants into less toxic forms (e.g., NOx to HNO3). This paper describes verification of the photocatalytic properties of titanium dioxide and presents the results of mechanical and physical tests on samples of architectural lightweight self-compacting concretes (LWSCC). The very essence of the use of LWSCC is their rheological ability to seep into otherwise extremely hard accessible or inaccessible construction areas, or sections thereof where concrete compacting will be a problem, or where vibration is completely excluded. They are also able to create a solid monolithic element with a large variety of shapes; the concrete will at the same meet the requirements of both chemical aggression and the influences of the surrounding environment. Due to their viscosity, LWSCCs are able to imprint the formwork elements into their structure and thus create high quality lightweight architectural concretes.
Abstract: This study investigates experimentally the effects
of hydrogen addition in the intake manifold of a diesel generator
operating with a 7% biodiesel-diesel oil blend (B7). An experimental
apparatus setup was used to conduct performance and emissions tests
in a single cylinder, air cooled diesel engine. This setup consisted
of a generator set connected to a wirewound resistor load bank that
was used to vary engine load. In addition, a flowmeter was used to
determine hydrogen volumetric flowrate and a digital anemometer
coupled with an air box to measure air flowrate. Furthermore, a
digital precision electronic scale was used to measure engine fuel
consumption and a gas analyzer was used to determine exhaust
gas composition and exhaust gas temperature. A thermopar was
installed near the exhaust collection to measure cylinder temperature.
In-cylinder pressure was measured using an AVL Indumicro data
acquisition system with a piezoelectric pressure sensor. An AVL
optical encoder was installed in the crankshaft and synchronized
with in-cylinder pressure in real time. The experimental procedure
consisted of injecting hydrogen into the engine intake manifold
at different mass concentrations of 2,6,8 and 10% of total fuel
mass (B7 + hydrogen), which represented energy fractions of 5,15,
20 and 24% of total fuel energy respectively. Due to hydrogen
addition, the total amount of fuel energy introduced increased
and the generators fuel injection governor prevented any increases
of engine speed. Several conclusions can be stated from the test
results. A reduction in specific fuel consumption as a function
of hydrogen concentration increase was noted. Likewise, carbon
dioxide emissions (CO2), carbon monoxide (CO) and unburned
hydrocarbons (HC) decreased as hydrogen concentration increased.
On the other hand, nitrogen oxides emissions (NOx) increased due
to average temperatures inside the cylinder being higher. There
was also an increase in peak cylinder pressure and heat release
rate inside the cylinder, since the fuel ignition delay was smaller
due to hydrogen content increase. All this indicates that hydrogen
promotes faster combustion and higher heat release rates and can
be an important additive to all kind of fuels used in diesel generators.
Abstract: Biomass such as corn and cassava wastes if left to decay will release significant quantities of greenhouse gases (GHG) including carbon dioxide and methane. The biomass wastes can be converted into biochar via thermochemical process such as slow pyrolysis. This approach can reduce the biomass wastes as well as preserve its carbon content. Biochar has the potential to be used as a carbon sequester and soil amendment. The aim of this study is to investigate the characteristics of the corn cob, cassava stem, and cassava rhizome in order to identify their potential as pyrolysis feedstocks for biochar production. This was achieved by using the proximate and elemental analyses as well as calorific value and lignocellulosic determination. The second objective is to investigate the effect of pyrolysis temperature on the biochar produced. A fixed bed slow pyrolysis reactor was used to pyrolyze the corn cob, cassava stem, and cassava rhizome. The pyrolysis temperatures were varied between 400 °C and 600 °C, while the heating rate and the holding time were fixed at 5 °C/min and 1 hour, respectively. Corn cob, cassava stem, and cassava rhizome were found to be suitable feedstocks for pyrolysis process because they contained a high percentage of volatile matter more than 80 mf wt.%. All the three feedstocks contained low nitrogen and sulphur content less than 1 mf wt.%. Therefore, during the pyrolysis process, the feedstocks give off very low rate of GHG such as nitrogen oxides and sulphur oxides. Independent of the types of biomass, the percentage of biochar yield is inversely proportional to the pyrolysis temperature. The highest biochar yield for each studied temperature is from slow pyrolysis of cassava rhizome as the feedstock contained the highest percentage of ash compared to the other two feedstocks. The percentage of fixed carbon in all the biochars increased as the pyrolysis temperature increased. The increment of pyrolysis temperature from 400 °C to 600 °C increased the fixed carbon of corn cob biochar, cassava stem biochar and cassava rhizome biochar by 26.35%, 10.98%, and 6.20% respectively. Irrespective of the pyrolysis temperature, all the biochars produced were found to contain more than 60 mf wt.% fixed carbon content, much higher than its feedstocks.
Abstract: Biodiesel is widely investigated to solve the twin
problem of depletion of fossil fuel and environmental degradation.
The main objective of the present work is to compare performance,
emissions, and combustion characteristics of biodiesel derived from
cotton seed oil in a diesel engine with the baseline results of
petrodiesel fuel. Tests have been conducted on a single cylinder, four
stroke CIDI diesel engine with a speed of 1500 rpm and a fixed
compression ratio of 17.5 at different load conditions. The
performance parameters evaluated include brake thermal efficiency,
brake specific fuel consumption, brake power, indicated mean
effective pressure, mechanical efficiency, and exhaust gas
temperature. Regarding combustion study, cylinder pressure, rate of
pressure rise, net heat release rate, cumulative heat release, mean gas
temperature, mass fraction burned, and fuel line pressure were
evaluated. The emission parameters such as carbon monoxide, carbon
dioxide, un-burnt hydrocarbon, oxides of nitrogen, and smoke
opacity were also measured by a smoke meter and an exhaust gas
analyzer and compared with baseline results. The brake thermal
efficiency of cotton seed oil methyl ester (CSOME) was lower than
that of petrodiesel and brake specific fuel consumption was found to
be higher. However, biodiesel resulted in the reduction of carbon
dioxide, un-burnt hydrocarbon, and smoke opacity at the expense of
nitrogen oxides. Carbon monoxide emissions for biodiesel was higher
at maximum output power. It has been found that the combustion
characteristics of cotton seed oil methyl ester closely followed those
of standard petrodiesel. The experimental results suggested that
biodiesel derived from cotton seed oil could be used as a good
substitute to petrodiesel fuel in a conventional diesel without any
modification.
Abstract: Computational fluid dynamics analysis of the burning
of syngas fuels derived from biomass and plastic solid waste mixture
through gasification process is presented in this paper. The syngas
fuel is burned in gas turbine can combustor. Gas turbine can
combustor with swirl is designed to burn the fuel efficiently and
reduce the emissions. The main objective is to test the impact of the
alternative syngas fuel compositions and lower heating value on the
combustion performance and emissions. The syngas fuel is produced
by blending palm kernel shell (PKS) with polyethylene (PE) waste
via catalytic steam gasification (fluidized bed reactor). High
hydrogen content syngas fuel was obtained by mixing 30% PE waste
with PKS. The syngas composition obtained through the gasification
process is 76.2% H2, 8.53% CO, 4.39% CO2 and 10.90% CH4. The
lower heating value of the syngas fuel is LHV = 15.98 MJ/m3. Three
fuels were tested in this study natural gas (100%CH4), syngas fuel
and pure hydrogen (100% H2). The power from the combustor was
kept constant for all the fuels tested in this study. The effect of syngas
fuel composition and lower heating value on the flame shape, gas
temperature, mass of carbon dioxide (CO2) and nitrogen oxides
(NOX) per unit of energy generation is presented in this paper. The
results show an increase of the peak flame temperature and NO mass
fractions for the syngas and hydrogen fuels compared to natural gas
fuel combustion. Lower average CO2 emissions at the exit of the
combustor are obtained for the syngas compared to the natural gas
fuel.
Abstract: The use of biodiesel in conventional diesel engines results in substantial reduction of unburned hydrocarbon, carbon monoxide and particulate matters. The performance, emission and combustion characteristics of a single cylinder four stroke variable compression ratio engine when fueled with Karanja (Pongamia) methyl ester and its 10-50 % blends with diesel (on a volume basis) are investigated and compared with standard diesel. The suitability of karanja methyl ester as a biofuel has been established in this study. The useful brake power obtained is similar to diesel fuel for all loads. Experiment has been conducted at a fixed engine speed of 1500 rpm, variable load and at compression ratios of 17.5:1 and 18.5:1. The impact of compression ratio on fuel consumption, combustion pressures and exhaust gas emissions has been investigated and presented. Optimum compression ratio which gives best performance has been identified. The results indicate longer ignition delay, maximum rate of pressure rise, lower heat release rate and higher mass fraction burnt at higher compression ratio for pongamia oil methyl ester when compared to that of diesel. The brake thermal efficiency for pongamia oil methyl ester blends and diesel has been calculated and the blend B20 is found to give maximum thermal efficiency. The blends when used as fuel results in reduction of carbon monoxide, hydrocarbon and increase in nitrogen oxides emissions. PME as an oxygenated fuel generated more complete combustion, which means increased torque and power. This is also supported with higher thermal efficiencies of the PME blends. NOx is slightly increased due to the higher combustion temperature and the presence of fuel oxygen with the blend at full load. PME as a new Biodiesel and its blends can be used in diesel engines without any engine modification.
Abstract: The performance, emission and combustion characteristics of a single cylinder four stroke variable compression ratio multi fuel engine when fueled with different blends of rice bran oil methyl ester and ethanol are investigated and compared with the results of standard diesel. Bio diesel produced from Rice bran oil by transesterification process has been used in this study. Experiment has been conducted at a fixed engine speed of 1500 rpm, 50% load and at compression ratios of 16.5:1, 17:1, 17.5:1 and 18:1. The impact of compression ratio on fuel consumption, brake thermal efficiency and exhaust gas emissions has been investigated and presented. Optimum compression ratio which gives best performance has been identified. The results indicate longer ignition delay, maximum rate of pressure rise, lower heat release rate and higher mass fraction burnt at higher compression ratio for waste cooking oil methyl ester when compared to that of diesel. The brake thermal efficiency at 50% load for Rice bran oil methyl ester blends and diesel has been calculated and the blend B40 is found to give maximum thermal efficiency. The blends when used as fuel results in reduction of carbon monoxide, hydrocarbon and increase in nitrogen oxides emissions.
Abstract: The aim of this study is to develop mathematical
relationships for the performance parameter brake thermal efficiency
(BTE) and emission parameter nitrogen oxides (NOx) for the various
esters of vegetable oils used as CI engine fuel. The BTE is an
important performance parameter defining the ability of engine to
utilize the energy supplied and power developed similarly it is
indication of efficiency of fuels used. The esters of cottonseed oil,
soybean oil, jatropha oil and hingan oil are prepared using
transesterification process and characterized for their physical and
main fuel properties including viscosity, density, flash point and
higher heating value using standard test methods. These esters are
tried as CI engine fuel to analyze the performance and emission
parameters in comparison to diesel. The results of the study indicate
that esters as a fuel does not differ greatly with that of diesel in
properties. The CI engine performance with esters as fuel is in line
with the diesel where as the emission parameters are reduced with the
use of esters.
The correlation developed between BTE and brake power(BP),
gross calorific value(CV), air-fuel ratio(A/F), heat carried away by
cooling water(HCW). Another equation is developed between the
NOx emission and CO, HC, smoke density (SD), exhaust gas
temperature (EGT). The equations are verified by comparing the
observed and calculated values which gives the coefficient of
correlation of 0.99 and 0.96 for the BTE and NOx equations
respectively.
Abstract: The value of emission factor was calculated in the
older type of Diesel engine operating on an engine testing bench and
then compared with the parameters monitored under similar
conditions when the EnviroxTM additive was applied. It has been
found out that the additive based on CeO2 nanoparticles reduces
emission of NOx. The dependencies of NOx emissions on reduced
torque, engine power and revolutions have been observed as well.
Abstract: Combustion, emission and performance
characterization of a single cylinder diesel engine using methanol
diesel blends was carried out. The blends were 5% (v/v) methanol in
diesel (MD05) and 10% (v/v) methanol in diesel (MD10). The
problem of solubility of methanol and diesel was addressed by an
agitator placed inside the fuel tank to prevent phase separation. The
results indicated that total combustion duration was reduced by15.8%
for MD05 and 31.27% for MD10compared to the baseline data.
Ignition delay was increased with increasing methanol volume
fraction in the test fuel. Total cyclic heat release was reduced by
1.5% for MD05 and 6.7% for MD10 as compared to diesel baseline.
Emissions of carbon monoxide, hydrocarbons along with smoke were
reduced and that of nitrogen oxides were increased with rising
methanol contents in the test fuel. Full load brake thermal efficiency
was marginally reduced with increased methanol composition in the
blend.
Abstract: Ground-level tropospheric ozone is one of the air
pollutants of most concern. It is mainly produced by photochemical
processes involving nitrogen oxides and volatile organic compounds
in the lower parts of the atmosphere. Ozone levels become
particularly high in regions close to high ozone precursor emissions
and during summer, when stagnant meteorological conditions with
high insolation and high temperatures are common.
In this work, some results of a study about urban ozone
distribution patterns in the city of Badajoz, which is the largest and
most industrialized city in Extremadura region (southwest Spain) are
shown. Fourteen sampling campaigns, at least one per month, were
carried out to measure ambient air ozone concentrations, during
periods that were selected according to favourable conditions to
ozone production, using an automatic portable analyzer.
Later, to evaluate the ozone distribution at the city, the measured
ozone data were analyzed using geostatistical techniques. Thus, first,
during the exploratory analysis of data, it was revealed that they were
distributed normally, which is a desirable property for the subsequent
stages of the geostatistical study. Secondly, during the structural
analysis of data, theoretical spherical models provided the best fit for
all monthly experimental variograms. The parameters of these
variograms (sill, range and nugget) revealed that the maximum
distance of spatial dependence is between 302-790 m and the
variable, air ozone concentration, is not evenly distributed in reduced
distances. Finally, predictive ozone maps were derived for all points
of the experimental study area, by use of geostatistical algorithms
(kriging). High prediction accuracy was obtained in all cases as
cross-validation showed. Useful information for hazard assessment
was also provided when probability maps, based on kriging
interpolation and kriging standard deviation, were produced.
Abstract: Nowadays, the focus on renewable energy and alternative fuels has increased due to increasing oil prices, environment pollution, and also concern on preserving the nature. Biodiesel has been known as an attractive alternative fuel although biodiesel produced from edible oil is very expensive than conventional diesel. Therefore, the uses of biodiesel produced from non-edible oils are much better option. Currently Jatropha biodiesel (JBD) is receiving attention as an alternative fuel for diesel engine. Biodiesel is non-toxic, biodegradable, high lubricant ability, highly renewable, and its use therefore produces real reduction in petroleum consumption and carbon dioxide (CO2) emissions. Although biodiesel has many advantages, but it still has several properties need to improve, such as lower calorific value, lower effective engine power, higher emission of nitrogen oxides (NOX) and greater sensitivity to low temperature. Exhaust gas recirculation (EGR) is effective technique to reduce NOX emission from diesel engines because it enables lower flame temperature and oxygen concentration in the combustion chamber. Some studies succeeded to reduce the NOX emission from biodiesel by EGR but they observed increasing soot emission. The aim of this study was to investigate the engine performance and soot emission by using blended Jatropha biodiesel with different EGR rates. A CI engine that is water-cooled, turbocharged, using indirect injection system was used for the investigation. Soot emission, NOX, CO2, carbon monoxide (CO) were recorded and various engine performance parameters were also evaluated.
Abstract: Acid rain occurs when sulphur dioxide (SO2) and
nitrogen oxides (Nox) gases react in the atmosphere with water,
oxygen, and other chemicals to form various acidic compounds. The
result is a mild solution of sulfuric acid and nitric acid. Soil has a
greater buffering capacity than aquatic systems. However excessive
amount of acids introduced by acid rains may disturb the entire soil
chemistry. Acidity and harmful action of toxic elements damage
vegetation while susceptible microbial species are eliminated. In
present study, the effects of simulated sulphuric acid and nitric acid
rains were investigated on crop Glycine max. The effect of acid rain
on change in soil fertility was detected in which pH of control sample
was 6.5 and pH of 1%H2SO4 and 1%HNO3 were 3.5. Nitrogen nitrate
in soil was high in 1% HNO3 treated soil & Control sample.
Ammonium nitrogen in soil was low in 1% HNO3 & H2SO4 treated
soil. Ammonium nitrogen was medium in control and other samples.
The effect of acid rain on seed germination on 3rd day of germination
control sample growth was 7 cm, 0.1% HNO3 was 8cm, and 0.001%
HNO3 & 0.001% H2SO4 was 6cm each. On 10th day fungal growth
was observed in 1% and 0.1%H2SO4 concentrations, when all plants
were dead. The effect of acid rain on crop productivity was
investigated on 3rd day roots were developed in plants. On12th day
Glycine max showed more growth in 0.1% HNO3, 0.001% HNO3 and
0.001% H2SO4 treated plants growth were same as compare to control
plants. On 20th day development of discoloration of plant pigments
were observed on acid treated plants leaves. On 38th day, 0.1, 0.001%
HNO3 and 0.1, 0.001% H2SO4 treated plants and control plants were
showing flower growth. On 42th day, acid treated Glycine max variety
and control plants were showed seeds on plants. In Glycine max
variety 0.1, 0.001% H2SO4, 0.1, 0.001% HNO3 treated plants were
dead on 46th day and fungal growth was observed. The toxicological
study was carried out on Glycine max plants exposed to 1% HNO3
cells were damaged more than 1% H2SO4. Leaf sections exposed to
0.001% HNO3 & H2SO4 showed less damaged of cells and
pigmentation observed in entire slide when compare with control
plant. The soil analysis was done to find microorganisms in HNO3 &
H2SO4 treated Glycine max and control plants. No microorganism
growth was observed in 1% HNO3 & H2SO4 but control plant showed
microbial growth.
Abstract: The present paper develops and validates a numerical procedure for the calculation of turbulent combustive flow in converging and diverging ducts and throuh simulation of the heat transfer processes, the amount of production and spread of Nox pollutant has been measured. A marching integration solution procedure employing the TDMA is used to solve the discretized equations. The turbulence model is the Prandtl Mixing Length method. Modeling the combustion process is done by the use of Arrhenius and Eddy Dissipation method. Thermal mechanism has been utilized for modeling the process of forming the nitrogen oxides. Finite difference method and Genmix numerical code are used for numerical solution of equations. Our results indicate the important influence of the limiting diverging angle of diffuser on the coefficient of recovering of pressure. Moreover, due to the intense dependence of Nox pollutant to the maximum temperature in the domain with this feature, the Nox pollutant amount is also in maximum level.
Abstract: In this study, a 3D combustion chamber was simulated
using FLUENT 6.32. Aim to obtain detailed information on
combustion characteristics and _ nitrogen oxides in the furnace and
the effect of oxygen enrichment in a combustion process. Oxygenenriched
combustion is an effective way to reduce emissions. This
paper analyzes NO emission, including thermal NO and prompt NO.
Flow rate ratio of air to fuel is varied as 1.3, 3.2 and 5.1 and the
oxygen enriched flow rates are 28, 54 and 68 lit/min. The 3D
Reynolds Averaged Navier Stokes (RANS) equations with standard
k-ε turbulence model are solved together by Fluent 6.32 software.
First order upwind scheme is used to model governing equations and
the SIMPLE algorithm is used as pressure velocity coupling. Results
show that for AF=1.3, increase the oxygen flow rate of oxygen
reduction in NO emissions is Lance. Moreover, in a fixed oxygen
enrichment condition, increasing the air to fuel ratio will increase the
temperature peak, but not the NO emission rate. As a result, oxygen
enrichment can reduce the NO emission at this kind of furnace in low
air to fuel rates.