Abstract: The aim of this paper is to determine the stress levels
at the end of a long slender shaft such as a drilling assembly used in
the oil or gas industry using a mathematical model in real-time. The
torsional deflection experienced by this type of drilling shaft (about 4
KM length and 20 cm diameter hollow shaft with a thickness of 1
cm) can only be determined using a distributed modeling technique.
The main objective of this project is to calculate angular velocity and
torque at the end of the shaft by TLM method and also analyzing of
the behavior of the system by transient response. The obtained result
is compared with lumped modeling technique the importance of these
results will be evident only after the mentioned comparison. Two
systems have different transient responses and in this project because
of the length of the shaft transient response is very important.
Abstract: The article deals with the relation between rainfall in selected months and subsequent weed infestation of spring barley. The field experiment was performed at Mendel University agricultural enterprise in Žabčice, Czech Republic. Weed infestation was measured in spring barley vegetation in years 2004 to 2012. Barley was grown in three tillage variants: conventional tillage technology (CT), minimization tillage technology (MT), and no tillage (NT). Precipitation was recorded in one-day intervals. Monthly precipitation was calculated from the measured values in the months of October through to April. The technique of canonical correspondence analysis was applied for further statistical processing. 41 different species of weeds were found in the course of the 9-year monitoring period. The results clearly show that precipitation affects the incidence of most weed species in the selected months, but acts differently in the monitored variants of tillage technologies.
Abstract: This paper presents design features of a rescue robot, named CEO Mission II. Its body is designed to be the track wheel type with double front flippers for climbing over the collapse and the rough terrain. With 125 cm. long, 5-joint mechanical arm installed on the robot body, it is deployed not only for surveillance from the top view but also easier and faster access to the victims to get their vital signs. Two cameras and sensors for searching vital signs are set up at the tip of the multi-joint mechanical arm. The third camera is at the back of the robot for driving control. Hardware and software of the system, which controls and monitors the rescue robot, are explained. The control system is used for controlling the robot locomotion, the 5-joint mechanical arm, and for turning on/off devices. The monitoring system gathers all information from 7 distance sensors, IR temperature sensors, 3 CCD cameras, voice sensor, robot wheels encoders, yawn/pitch/roll angle sensors, laser range finder and 8 spare A/D inputs. All sensors and controlling data are communicated with a remote control station via IEEE 802.11b Wi-Fi. The audio and video data are compressed and sent via another IEEE 802.11g Wi-Fi transmitter for getting real-time response. At remote control station site, the robot locomotion and the mechanical arm are controlled by joystick. Moreover, the user-friendly GUI control program is developed based on the clicking and dragging method to easily control the movement of the arm. Robot traveling map is plotted from computing the information of wheel encoders and the yawn/pitch data. 2D Obstacle map is plotted from data of the laser range finder. The concept and design of this robot can be adapted to suit many other applications. As the Best Technique awardee from Thailand Rescue Robot Championship 2006, all testing results are satisfied.
Abstract: This paper proposes a novel system for monitoring the
health of underground pipelines. Some of these pipelines transport
dangerous contents and any damage incurred might have catastrophic
consequences. However, most of these damage are unintentional and
usually a result of surrounding construction activities. In order to
prevent these potential damages, monitoring systems are
indispensable. This paper focuses on acoustically recognizing road
cutters since they prelude most construction activities in modern
cities. Acoustic recognition can be easily achieved by installing a
distributed computing sensor network along the pipelines and using
smart sensors to “listen" for potential threat; if there is a real threat,
raise some form of alarm. For efficient pipeline monitoring, a novel
monitoring approach is proposed. Principal Component Analysis
(PCA) was studied and applied. Eigenvalues were regarded as the
special signature that could characterize a sound sample, and were
thus used for the feature vector for sound recognition. The denoising
ability of PCA could make it robust to noise interference. One class
SVM was used for classifier. On-site experiment results show that the
proposed PCA and SVM based acoustic recognition system will be
very effective with a low tendency for raising false alarms.
Abstract: This paper presents the development of analysis tools
for Home Agriculture project. The tools are required for monitoring
the condition of greenhouse which involves two components:
measurement hardware and data analysis engine. Measurement
hardware is functioned to measure environment parameters such as
temperature, humidity, air quality, dust and etc while analysis tool is
used to analyse and interpret the integrated data against the condition
of weather, quality of health, irradiance, quality of soil and etc. The
current development of the tools is completed for off-line data
recorded technique. The data is saved in MMC and transferred via
ZigBee to Environment Data Manager (EDM) for data analysis.
EDM converts the raw data and plot three combination graphs. It has
been applied in monitoring three months data measurement for
irradiance, temperature and humidity of the greenhouse..
Abstract: TELMES project aims to develop a securized
multimedia system devoted to medical consultation teleservices. It
will be finalized with a pilot system for a regional telecenters
network that connects local telecenters, having as support
multimedia platforms. This network will enable the implementation
of complex medical teleservices (teleconsulations, telemonitoring,
homecare, urgency medicine, etc.) for a broader range of patients
and medical professionals, mainly for family doctors and those
people living in rural or isolated regions. Thus, a multimedia,
scalable network, based on modern IT&C paradigms, will result. It
will gather two inter-connected regional telecenters, in Iaşi and
Piteşti, Romania, each of them also permitting local connections of
hospitals, diagnostic and treatment centers, as well as local networks
of family doctors, patients, even educational entities. As
communications infrastructure, we aim to develop a combined fixmobile-
internet (broadband) links. Other possible communication
environments will be GSM/GPRS/3G and radio waves. The
electrocardiogram (ECG) acquisition, internet transmission and
local analysis, using embedded technologies, was already
successfully done for patients- telemonitoring.
Abstract: This paper presented a new approach for centralized
monitoring and self-protected against fiber fault in fiber-to-the-home
(FTTH) access network by using Smart Access Network Testing,
Analyzing and Database (SANTAD). SANTAD will be installed
with optical line terminal (OLT) at central office (CO) for in-service
transmission surveillance and fiber fault localization within FTTH
with point-to-multipoint (P2MP) configuration downwardly from CO
towards customer residential locations based on the graphical user
interface (GUI) processing capabilities of MATLAB software.
SANTAD is able to detect any fiber fault as well as identify the
failure location in the network system. SANTAD enable the status of
each optical network unit (ONU) connected line is displayed onto
one screen with capability to configure the attenuation and detect the
failure simultaneously. The analysis results and information will be
delivered to the field engineer for promptly actions, meanwhile the
failure line will be diverted to protection line to ensure the traffic
flow continuously. This approach has a bright prospect to improve
the survivability and reliability as well as increase the efficiency and
monitoring capabilities in FTTH.
Abstract: Wavelet transform has been extensively used in
machine fault diagnosis and prognosis owing to its strength to deal
with non-stationary signals. The existing Wavelet transform based
schemes for fault diagnosis employ wavelet decomposition of the
entire vibration frequency which not only involve huge
computational overhead in extracting the features but also increases
the dimensionality of the feature vector. This increase in the
dimensionality has the tendency to 'over-fit' the training data and
could mislead the fault diagnostic model. In this paper a novel
technique, envelope wavelet packet transform (EWPT) is proposed in
which features are extracted based on wavelet packet transform of the
filtered envelope signal rather than the overall vibration signal. It not
only reduces the computational overhead in terms of reduced number
of wavelet decomposition levels and features but also improves the
fault detection accuracy. Analytical expressions are provided for the
optimal frequency resolution and decomposition level selection in
EWPT. Experimental results with both actual and simulated machine
fault data demonstrate significant gain in fault detection ability by
EWPT at reduced complexity compared to existing techniques.
Abstract: The aged are faced with increasing risk for falls. The
aged have the easily fragile bones than others. When falls have
occurred, it is important to detect this emergency state because such
events often lead to more serious illness or even death. A
implementation of PDA system, for detection of emergency situation,
was developed using 3-axis accelerometer in this paper as follows.
The signals were acquired from the 3-axis accelerometer, and then
transmitted to the PDA through Bluetooth module. This system can
classify the human activity, and also detect the emergency state like
falls. When the fall occurs, the system generates the alarm on the
PDA. If a subject does not respond to the alarm, the system determines
whether the current situation is an emergency state or not, and then
sends some information to the emergency center in the case of urgent
situation. Three different studies were conducted on 12 experimental
subjects, with results indicating a good accuracy. The first study was
performed to detect the posture change of human daily activity. The
second study was performed to detect the correct direction of fall. The
third study was conducted to check the classification of the daily
physical activity. Each test was lasted at least 1 min. in third study.
The output of acceleration signal was compared and evaluated by
changing a various posture after attaching a 3-axis accelerometer
module on the chest. The newly developed system has some important
features such as portability, convenience and low cost. One of the
main advantages of this system is that it is available at home
healthcare environment. Another important feature lies in low cost to
manufacture device. The implemented system can detect the fall
accurately, so will be widely used in emergency situation.
Abstract: Analysis of reciprocating equipment piston rod leads
to nonlinear elastic-plastic deformation analysis of rod with initial
imperfection under axial dynamic load. In this paper a new and
effective model and analytical formulations are presented to evaluate
dynamic deformation and elastic-plastic stresses of reciprocating
machine piston rod. This new method has capability to account for
geometric nonlinearity, elastic-plastic deformation and dynamic
effects. Proposed method can be used for evaluation of piston rod
performance for various reciprocating machines under different
operation situations. Rod load curves and maximum allowable rod
load are calculated with presented method for a refinery type
reciprocating compressor. Useful recommendations and guidelines
for rod load, rod load reversal and rod drop monitoring are also
addressed.
Abstract: In order to implement flexibility as well as survivable
capacities over passive optical network (PON), a new automatic
random fault-recovery mechanism with array-waveguide-grating
based (AWG-based) optical switch (OSW) is presented. Firstly,
wavelength-division-multiplexing and optical code-division
multiple-access (WDM/OCDMA) scheme are configured to meet the
various geographical locations requirement between optical network
unit (ONU) and optical line terminal (OLT). The AWG-base optical
switch is designed and viewed as central star-mesh topology to
prohibit/decrease the duplicated redundant elements such as fiber and
transceiver as well. Hence, by simple monitoring and routing switch
algorithm, random fault-recovery capacity is achieved over
bi-directional (up/downstream) WDM/OCDMA scheme. When error
of distribution fiber (DF) takes place or bit-error-rate (BER) is higher
than 10-9 requirement, the primary/slave AWG-based OSW are
adjusted and controlled dynamically to restore the affected ONU
groups via the other working DFs immediately.
Abstract: This paper describes studies carried out to investigate
the viability of using wireless cameras as a tool in monitoring
changes in air quality. A camera is used to monitor the change in
colour of a chemically responsive polymer within view of the camera
as it is exposed to varying chemical species concentration levels. The
camera captures this image and the colour change is analyzed by
averaging the RGB values present. This novel chemical sensing
approach is compared with an established chemical sensing method
using the same chemically responsive polymer coated onto LEDs. In
this way, the concentration levels of acetic acid in the air can be
tracked using both approaches. These approaches to chemical plume
tracking have many applications for air quality monitoring.
Abstract: Variable speed drives are growing and varying. Drives expanse depend on progress in different part of science like power system, microelectronic, control methods, and so on. Artificial intelligent contains hard computation and soft computation. Artificial intelligent has found high application in most nonlinear systems same as motors drive. Because it has intelligence like human but there are no sentimental against human like angriness and.... Artificial intelligent is used for various points like approximation, control, and monitoring. Because artificial intelligent techniques can use as controller for any system without requirement to system mathematical model, it has been used in electrical drive control. With this manner, efficiency and reliability of drives increase and volume, weight and cost of them decrease.
Abstract: As current business environment is demanding a
constant adaptation of companies, the planning and strategic
management should be an ongoing and natural process in all kind of
organizations. The use of management and monitoring strategic
performance tools such as the Balanced Scorecard (BSC) have been
popular; even to Small and Medium-sized Enterprises. This paper
aims to investigate whether the BSC is being used in monitoring the
performance of small businesses, particularly in small fuel retailers
companies, which are competing in co-branding; and if not, it aims to
identify its strategic orientation in order to recommend a possible
strategy map for those managers that are willing to adopt this model
as an alternative to traditional ones for organizational performance
evaluation, which often focus only on evaluation of the
organizational financial performance.
Abstract: This paper presents a low cost design of heart beat monitoring device using reflectance mode PhotoPlethysmography (PPG). PPG is known for its simple construction, ease of use and cost effectiveness and can provide information about the changes in cardiac activity as well as aid in earlier non-invasive diagnostics. The proposed device is divided into three phases. First is the detection of pulses through the fingertip. The signal is then passed to the signal processing unit for the purpose of amplification, filtering and digitizing. Finally the heart rate is calculated and displayed on the computer using parallel port interface. The paper is concluded with prototyping of the device followed by verification procedure of the heartbeat signal obtained in laboratory setting.
Abstract: Recently there has been a growing interest in the field
of bio-mimetic robots that resemble the behaviors of an insect or an
aquatic animal, among many others. One of various bio-mimetic robot
applications is to explore pipelines, spotting any troubled areas or
malfunctions and reporting its data. Moreover, the robot is able to
prepare for and react to any abnormal routes in the pipeline. Special
types of mobile robots are necessary for the pipeline monitoring tasks.
In order to move effectively along a pipeline, the robot-s movement
will resemble that of insects or crawling animals. When situated in
massive pipelines with complex routes, the robot places fixed sensors
in several important spots in order to complete its monitoring. This
monitoring task is to prevent a major system failure by preemptively
recognizing any minor or partial malfunctions. Areas uncovered by
fixed sensors are usually impossible to provide real-time observation
and examination, and thus are dependent on periodical offline
monitoring. This paper proposes a monitoring system that is able to
monitor the entire area of pipelines–with and without fixed
sensors–by using the bio-mimetic robot.
Abstract: In this paper is presented a Geographic Information System (GIS) approach in order to qualify and monitor the broadband lines in efficient way. The methodology used for interpolation is the Delaunay Triangular Irregular Network (TIN). This method is applied for a case study in ISP Greece monitoring 120,000 broadband lines.
Abstract: Time varying network induced delays in networked
control systems (NCS) are known for degrading control system-s
quality of performance (QoP) and causing stability problems. In
literature, a control method employing modeling of communication
delays as probability distribution, proves to be a better method. This
paper focuses on modeling of network induced delays as probability
distribution.
CAN and MIL-STD-1553B are extensively used to carry periodic
control and monitoring data in networked control systems.
In literature, methods to estimate only the worst-case delays for
these networks are available. In this paper probabilistic network
delay model for CAN and MIL-STD-1553B networks are given.
A systematic method to estimate values to model parameters from
network parameters is given. A method to predict network delay in
next cycle based on the present network delay is presented. Effect of
active network redundancy and redundancy at node level on network
delay and system response-time is also analyzed.
Abstract: The world-s largest Pre-stressed Concrete Cylinder
Pipe (PCCP) water supply project had a series of pipe failures which
occurred between 1999 and 2001. This has led the Man-Made River
Authority (MMRA), the authority in charge of the implementation
and operation of the project, to setup a rehabilitation plan for the
conveyance system while maintaining the uninterrupted flow of
water to consumers. At the same time, MMRA recognized the need
for a long term management tool that would facilitate repair and
maintenance decisions and enable taking the appropriate preventive
measures through continuous monitoring and estimation of the
remaining life of each pipe. This management tool is known as the
Pipe Risk Management System (PRMS) and now in operation at
MMRA. Both the rehabilitation plan and the PRMS require the
availability of complete and accurate pipe construction and
manufacturing data
This paper describes a systematic approach of data collection,
analysis, evaluation and correction for the construction and
manufacturing data files of phase I pipes which are the platform for
the PRMS database and any other related decision support system.
Abstract: Power cables are vulnerable to failure due to aging or
defects that occur with the passage of time under continuous
operation and loading stresses. PD detection and characterization
provide information on the location, nature, form and extent of the
degradation. As a result, PD monitoring has become an important
part of condition based maintenance (CBM) program among power
utilities. Online partial discharge (PD) localization of defect sources
in power cable system is possible using the time of flight method.
The information regarding the time difference between the main and
reflected pulses and cable length can help in locating the partial
discharge source along the cable length. However, if the length of
the cable is not known and the defect source is located at the extreme
ends of the cable or in the middle of the cable, then double ended
measurement is required to indicate the location of PD source. Use of
multiple sensors can also help in discriminating the cable PD or local/
external PD. This paper presents the experience and results from
online partial discharge measurements conducted in the laboratory
and the challenges in partial discharge source localization.