Abstract: Increasing demands of contemporary applications for high strength and lightweight materials prompted the development of metal-matrix composites (MMCs). After the discovery of carbon nanotubes (CNTs) in 1991 (revealing an excellent set of mechanical properties) became one of the most promising strengthening materials for MMC applications. Additionally, the relatively low density of the nanotubes imparted high specific strengths, making them perfect strengthening material to reinforce MMCs. In the present study, aluminum-multiwalled carbon nanotubes (Al-MWCNTs) composite was prepared in an air induction furnace. The dispersion of the nanotubes in molten aluminum was assisted by inherent string action of induction heating at 790°C. During the fabrication process, multifunctional fluxes were used to avoid oxidation of the nanotubes and molten aluminum. Subsequently, the melt was cast in to a copper mold and cold rolled to 0.5 mm thickness. During metallographic examination using a scanning electron microscope, it was observed that the nanotubes were effectively dispersed in the matrix. The mechanical properties of the composite were significantly increased as compared to pure aluminum specimen i.e. the yield strength from 65 to 115 MPa, the tensile strength from 82 to 125 MPa and hardness from 27 to 30 HV for pure aluminum and Al-CNTs composite, respectively. To recognize the associated strengthening mechanisms in the nanocomposites, three foremost strengthening models i.e. shear lag model, Orowan looping and Hall-Petch have been critically analyzed; experimental data were found to be closely satisfying the shear lag model.
Abstract: High temperature deformation behavior of cast
Fe-20Cr-5Al alloy has been investigated in this study by performing
tensile and compression tests at temperatures from 1100 to 1200oC.
Rectangular ingots of which the dimensions were 300×300×100 in
millimeter were cast using vacuum induction melting. Phase
equilibrium was calculated using the FactSage®, thermodynamic
software and database. Tensile strength of cast Fe-20Cr-5Al alloy was
4 MPa at 1200oC. With temperature decreased, tensile strength
increased rapidly and reached up to 13 MPa at 1100oC. Elongation
also increased from 18 to 80% with temperature decreased from
1200oC to 1100oC. Microstructure observation revealed that M23C6
carbide was precipitated along the grain boundary and within the
matrix.
Abstract: High temperature deformation behavior of cast 310S stainless steel has been investigated in this study by performing tensile and compression tests at temperatures from 900 to 1200oC. Rectangular ingots of which the dimensions were 350×350×100 in millimeter were cast using vacuum induction melting. Phase equilibrium was calculated using the FactSage®, thermodynamic software and database. Thermal expansion coefficient was also measured on the ingot in the temperature range from room temperature to 1200oC. Tensile strength of cast 310S stainless steel was 9 MPa at 1200oC, which is a little higher than that of a wrought 310S. With temperature decreased, tensile strength increased rapidly and reached up to 72 MPa at 900oC. Elongation also increased with temperature decreased. Microstructure observation revealed that s phase was precipitated along the grain boundary and within the matrix over 1200oC, which is detrimental to high temperature elongation.
Abstract: In the present study, the effect of Si, Al, Ti, Zr, and Nb addition on the microstructure and hot workability of cast M42 tool steels, basically consisting of 1.0C, 0.2Mn, 3.8Cr, 1.5W, 8.5Co, 9.2Mo, and 1.0V in weight percent has been investigated. Tool steels containing Si of 0.25 and 0.5wt.%, Al of 0.06 and 0.12wt.%, Ti of 0.3wt.%, Zr of 0.3wt.%, and Nb of 0.3wt.% were cast into ingots of 140mm ´ 140mm ´ 330mm by vacuum induction melting. After solution treatment at 1150oC for 1.5hr followed by furnace cooling, hot rolling at 1180oC was conducted on the ingots. Addition of titanium, zirconium and niobium was found to retard the decomposition of the eutectic carbides and result in the deterioration of hot workability of the tool steels, while addition of aluminum and silicon showed relatively well decomposed carbide structure and resulted in sound hot rolled plates.
Abstract: Most buildings have been using anchor bolts
commonly for installing outdoor advertising structures. Anchor bolts
of common carbon steel are widely used and often installed
indiscriminately by inadequate installation standards. In the area
where strong winds frequently blow, falling accidents of outdoor
advertising structures can occur and cause a serious disaster, which is
very dangerous and to be prevented. In this regard, the development of
high-performance anchor bolts is urgently required. In the present
study, 25Cr-8Ni-1.5Si-1Mn-0.4C alloy was produced by traditional
vacuum induction melting (VIM) for the application of anchor bolt.
The alloy composition is revealed as a duplex microstructure from
thermodynamic phase analysis by FactSage® and confirmed by
metallographic experiment. Addition of Nitrogen to the alloy was
found to reduce the ferritic phase domain and significantly increase the
hardness and the tensile strength. Microstructure observation revealed
mixed structure of austenite and ferrite with fine carbide distributed
along the grain and phase boundaries.