Abstract: This paper describes three lumped parameters models
for the study of the dynamic behavior of a boom crane. The models
here proposed allows to evaluate the fluctuations of the load arising
from the rope and structure elasticity and from the type of the
motion command imposed by the winch. A calculation software
was developed in order to determine the actual acceleration of the
lifted mass and the dynamic overload during the lifting phase. Some
application examples are presented, with the aim of showing the
correlation between the magnitude of the stress and the type of the
employed motion command.
Abstract: Si-Ge solid solutions (bulk poly- and mono-crystalline
samples, thin films) are characterized by high perspectives for
application in semiconductor devices, in particular, optoelectronics
and microelectronics. From this point of view, complex studying of
structural state of the defects and structural-sensitive physical
properties of Si-Ge solid solutions depending on the contents of Si
and Ge components is very important. Present work deals with the
investigations of microstructure, microhardness, internal friction and
shear modulus of Si1-xGex(x≤0,02) bulk monocrystals conducted at
room temperature. Si-Ge bulk crystals were obtained by Czochralski
method in [111] crystallographic direction. Investigated
monocrystalline Si-Ge samples are characterized by p-type
conductivity and carriers’ concentration 5.1014-1.1015cm-3.
Microhardness was studied on Dynamic Ultra Micro hardness Tester
DUH-201S with Berkovich indenter. Investigate samples are characterized with 0,5x0,5x(10-15)mm3
sizes, oriented along [111] direction at torsion oscillations ≈1Hz,
multistage changing of internal friction and shear modulus has been
revealed in an interval of strain amplitude of 10-5-5.10-3. Critical
values of strain amplitude have been determined at which hysteretic
changes of inelastic characteristics and microplasticity are observed. The critical strain amplitude and elasticity limit values are also
determined. Dynamic mechanical characteristics decreasing trend is
shown with increasing Ge content in Si-Ge solid solutions. Observed
changes are discussed from the point of view of interaction of various
dislocations with point defects and their complexes in a real structure
of Si-Ge solid solutions.
Abstract: The purpose of the present work was to develop an innovative food product with good textural and sensorial characteristics. The product, a new type of bread, was prepared with wheat (90%) and lupin (10%) flours, without the addition of any conservatives. Several experiences were also done to find the most appropriate proportion of lupin flour. The optimized product was characterized considering the rheological, physical-chemical and sensorial properties. The water absorption of wheat flour with 10% of lupin was higher than that of the normal wheat flours, and Wheat Ceres flour presented the lower value, with lower dough development time and high stability time. The breads presented low moisture but a considerable water activity. The density of bread decreased with the introduction of lupin flour. The breads were quite white, and during storage the colour parameters decreased. The lupin flour clearly increased the number of alveolus, but the total area increased significantly just for the Wheat Cerealis bread. The addition of lupin flour increased the hardness and chewiness of breads, but the elasticity did not vary significantly. Lupin bread was sensorially similar to wheat bread produced with WCerealis flour, and the main differences are the crust rugosity, colour and alveolus characteristics.
Abstract: It is the patient compliance and stability in
combination with controlled drug delivery and biocompatibility that
forms the core feature in present research and development of
sustained biodegradable patch formulation intended for wound
healing. The aim was to impart sustained degradation, sterile
formulation, significant folding endurance, elasticity,
biodegradability, bio-acceptability and strength. The optimized
formulation comprised of polymers including Hydroxypropyl methyl
cellulose, Ethylcellulose, and Gelatin, and Citric Acid PEG Citric
acid (CPEGC) triblock dendrimers and active Curcumin. Polymeric
mixture dissolved in geometric order in suitable medium through
continuous stirring under ambient conditions. With continued stirring
Curcumin was added with aid of DCM and Methanol in optimized
ratio to get homogenous dispersion. The dispersion was sonicated
with optimum frequency and for given time and later casted to form a
patch form. All steps were carried out under strict aseptic conditions.
The formulations obtained in the acceptable working range were
decided based on thickness, uniformity of drug content, smooth
texture and flexibility and brittleness. The patch kept on stability
using butter paper in sterile pack displayed folding endurance in
range of 20 to 23 times without any evidence of crack in an
optimized formulation at room temperature (RT) (24 ± 2°C). The
patch displayed acceptable parameters after stability study conducted
in refrigerated conditions (8±0.2°C) and at RT (24 ± 2°C) up to 90
days. Further, no significant changes were observed in critical
parameters such as elasticity, biodegradability, drug release and drug
content during stability study conducted at RT 24±2°C for 45 and 90
days. The drug content was in range 95 to 102%, moisture content
didn’t exceeded 19.2% and patch passed the content uniformity test.
Percentage cumulative drug release was found to be 80% in 12h and
matched the biodegradation rate as drug release with correlation
factor R2>0.9. The biodegradable patch based formulation developed
shows promising results in terms of stability and release profiles.
Abstract: In this paper, relationship between different properties
of IC concrete and water cement ratio, obtained from a
comprehensive experiment conducted on IC using local materials
(Burnt clay chips- BC) is presented. In addition, saturated SAP was
used as an IC material in some cases. Relationships have been
developed through regression analysis. The focus of this analysis is
on developing relationship between a dependent variable and an
independent variable. Different percent replacements of BC and
water cement ratios were used. Compressive strength, modulus of
elasticity, water permeability and chloride permeability were tested
and variations of these parameters were analyzed with respect to
water cement ratio.
Abstract: The paper presents an advanced control system for
tennis ball throwing machines to improve their accuracy according to
the ball impact points. A further advantage of the system is the much
easier calibration process involving the intelligent solution of the
automatic adjustment of the stroking parameters according to the ball
elasticity, the self-calibration, the use of the safety margin at very flat
strokes and the possibility to placing the machine to any position of
the half court. The system applies mathematical methods to
determine the exact ball trajectories and special approximating
processes to access all points on the aimed half court.
Abstract: This paper presents a fully Lagrangian coupled
Fluid-Structure Interaction (FSI) solver for simulations of
fluid-structure interactions, which is based on the Moving Particle
Semi-implicit (MPS) method to solve the governing equations
corresponding to incompressible flows as well as elastic structures.
The developed solver is verified by reproducing the high velocity
impact loads of deformable thin wedges with three different materials
such as mild steel, aluminium and tin during water entry. The present
simulation results for aluminium are compared with analytical solution
derived from the hydrodynamic Wagner model and linear Wan’s
theory. And also, the impact pressure and strain on the water entry
wedge with three different materials, such as mild steel, aluminium
and tin, are simulated and the effects of hydro-elasticity are discussed.
Abstract: This paper deals with nonlinear vibration analysis
using finite element method for frame structures consisting of elastic
and viscoelastic damping layers supported by multiple nonlinear
concentrated springs with hysteresis damping. The frame is supported
by four nonlinear concentrated springs near the four corners. The
restoring forces of the springs have cubic non-linearity and linear
component of the nonlinear springs has complex quantity to represent
linear hysteresis damping. The damping layer of the frame structures
has complex modulus of elasticity. Further, the discretized equations in
physical coordinate are transformed into the nonlinear ordinary
coupled differential equations using normal coordinate corresponding
to linear natural modes. Comparing shares of strain energy of the
elastic frame, the damping layer and the springs, we evaluate the
influences of the damping couplings on the linear and nonlinear impact
responses. We also investigate influences of damping changed by
stiffness of the elastic frame on the nonlinear coupling in the damped
impact responses.
Abstract: This study aims to evaluate the effective size, section
and structural characteristics of circular hollow steel (CHS) damper.
CHS damper is among steel dampers which are used widely for
seismic energy dissipation because they are easy to install, maintain
and are inexpensive. CHS damper dissipates seismic energy through
metallic deformation due to the geometrical elasticity of circular shape
and fatigue resistance around connection part. After calculating the
effective size, which is found to be height to diameter ratio of √3,
nonlinear FE analyses were carried out to evaluate the structural
characteristics and effective section (diameter-to-ratio).
Abstract: The paper is focused on monitoring of dependencies
of different composition concretes on elastic modulus values.
To obtain a summary of elastic modulus development in dependence
of concrete composition design variability was the objective
of the experiment. Essential part of this work was initiated
as a reaction to building practice when questions of elastic moduli
arose at the same time and which mostly did not obtain the required
and expected values from concrete constructions.
Abstract: The modeling lung respiratory system that has complex anatomy and biophysics presents several challenges including tissue-driven flow patterns and wall motion. Also, the pulmonary lung system because of that they stretch and recoil with each breath, has not static walls and structures. The direct relationship between air flow and tissue motion in the lung structures naturally prefers an FSI simulation technique. Therefore, in order to toward the realistic simulation of pulmonary breathing mechanics the development of a coupled FSI computational model is an important step. A simple but physiologically relevant three-dimensional deep long geometry is designed and fluid-structure interaction (FSI) coupling technique is utilized for simulating the deformation of the lung parenchyma tissue that produces airflow fields. The real understanding of respiratory tissue system as a complex phenomenon have been investigated with respect to respiratory patterns, fluid dynamics and tissue viscoelasticity and tidal breathing period.
Abstract: Knowledge of bone mechanical properties is important
for bone substitutes design and fabrication, and more efficient
prostheses development. The aim of this study is to characterize the
viscoelastic behavior of bone specimens, through stress relaxation
and fatigue tests performed to trabecular bone samples from bovine
femoral heads. Relaxation tests consisted on preloading the samples
at five different magnitudes and evaluate them for 1020 seconds,
adjusting the results to a KWW mathematical model. Fatigue tests
consisted of 700 load cycles and analyze their status at the end of the
tests. As a conclusion we have that between relaxation stress and
each preload there is linear relation and for samples with initial
Young´s modulus greater than 1.5 GPa showed no effects due fatigue
test loading cycles.
Abstract: On the basis of the theory of nonlinear elasticity, the
effect of homogeneous stress on the propagation of Lamb waves in
an initially isotropic hyperelastic plate is analysed. The equations
governing the propagation of small amplitude waves in the prestressed
plate are derived using the theory of small deformations
superimposed on large deformations. By enforcing traction free
boundary conditions at the upper and lower surfaces of the plate,
acoustoelastic dispersion equations for Lamb wave propagation are
obtained, which are solved numerically. Results are given for an
aluminum plate subjected to a range of applied stresses.
Abstract: An innovative flooring underlayment was produced
and tested. The composite system is made of common OSB boards
and a layer of eco-friendly non-cement gypsum based material
(GeoGypTM). It was found that the shear bond between the two
materials is sufficient to secure the composite interaction between the
two. The very high compressive strength and relatively high tensile
strength of the non-cement based component together with its high
modulus of elasticity provides enough strength and stiffness for the
composite product to cover wider spacing between the joists. The
initial findings of this study indicate that with joist spacing as wide as
800 mm, the flooring system provides enough strength without
compromising the serviceability requirements of the building codes.
Abstract: There are several possibilities of reducing the required
amount of cement in concrete production. Natural zeolite is one of
the raw materials which can partly substitute Portland cement. The
effort to reduce the amount of Portland cement used in concrete
production is brings both economical as well as ecological benefits.
The paper presents the properties of concrete containing natural
zeolite as an active admixture in the concrete which partly substitutes
Portland cement. The properties discussed here bring information
about the basic mechanical properties and frost resistance of concrete
containing zeolite. The properties of concretes with the admixture of
zeolite are compared with a reference concrete with no content of
zeolite. The properties of the individual concretes are observed for
360 days.
Abstract: The problem of toughening in brittle materials
reinforced by fibers is complex, involving all of the mechanical
properties of fibers, matrix and the fiber/matrix interface, as well as
the geometry of the fiber. Development of new numerical methods
appropriate to toughening simulation and analysis is necessary. In
this work, we have performed simulations and analysis of toughening
in brittle matrix reinforced by randomly distributed fibers by means
of the discrete elements method. At first, we put forward a
mechanical model of toughening contributed by random fibers. Then
with a numerical program, we investigated the stress, damage and
bridging force in the composite material when a crack appeared in the
brittle matrix. From the results obtained, we conclude that: (i) fibers
of high strength and low elasticity modulus are beneficial to
toughening; (ii) fibers of relatively high elastic modulus compared to
the matrix may result in substantial matrix damage due to spalling
effect; (iii) employment of high-strength synthetic fibers is a good
option for toughening. We expect that the combination of the discrete
element method (DEM) with the finite element method (FEM) can
increase the versatility and efficiency of the software developed. The
present work can guide the design of ceramic composites of high
performance through the optimization of the parameters.
Abstract: Two finite element (FEM) models are presented in
this paper to address the random nature of the response of glued
timber structures made of wood segments with variable elastic
moduli evaluated from 3600 indentation measurements. This total
database served to create the same number of ensembles as was the
number of segments in the tested beam. Statistics of these ensembles
were then assigned to given segments of beams and the Latin
Hypercube Sampling (LHS) method was called to perform 100
simulations resulting into the ensemble of 100 deflections subjected
to statistical evaluation. Here, a detailed geometrical arrangement of
individual segments in the laminated beam was considered in the
construction of two-dimensional FEM model subjected to in fourpoint
bending to comply with the laboratory tests. Since laboratory
measurements of local elastic moduli may in general suffer from a
significant experimental error, it appears advantageous to exploit the
full scale measurements of timber beams, i.e. deflections, to improve
their prior distributions with the help of the Bayesian statistical
method. This, however, requires an efficient computational model
when simulating the laboratory tests numerically. To this end, a
simplified model based on Mindlin’s beam theory was established.
The improved posterior distributions show that the most significant
change of the Young’s modulus distribution takes place in laminae in
the most strained zones, i.e. in the top and bottom layers within the
beam center region. Posterior distributions of moduli of elasticity
were subsequently utilized in the 2D FEM model and compared with
the original simulations.
Abstract: Starting from nonlocal continuum mechanics, a
thermodynamically new nonlocal model of Euler-Bernoulli
nanobeams is provided. The nonlocal variational formulation is
consistently provided and the governing differential equation for
transverse displacement is presented. Higher-order boundary
conditions are then consistently derived. An example is contributed in
order to show the effectiveness of the proposed model.
Abstract: The Cone Penetration Test (CPT) is a common in-situ
test which generally investigates a much greater volume of soil more
quickly than possible from sampling and laboratory tests. Therefore,
it has the potential to realize both cost savings and assessment of soil
properties rapidly and continuously. The principle objective of this
paper is to demonstrate the feasibility and efficiency of using
artificial neural networks (ANNs) to predict the soil angle of internal
friction (Φ) and the soil modulus of elasticity (E) from CPT results
considering the uncertainties and non-linearities of the soil. In
addition, ANNs are used to study the influence of different
parameters and recommend which parameters should be included as
input parameters to improve the prediction. Neural networks discover
relationships in the input data sets through the iterative presentation
of the data and intrinsic mapping characteristics of neural topologies.
General Regression Neural Network (GRNN) is one of the powerful
neural network architectures which is utilized in this study. A large
amount of field and experimental data including CPT results, plate
load tests, direct shear box, grain size distribution and calculated data
of overburden pressure was obtained from a large project in the
United Arab Emirates. This data was used for the training and the
validation of the neural network. A comparison was made between
the obtained results from the ANN's approach, and some common
traditional correlations that predict Φ and E from CPT results with
respect to the actual results of the collected data. The results show
that the ANN is a very powerful tool. Very good agreement was
obtained between estimated results from ANN and actual measured
results with comparison to other correlations available in the
literature. The study recommends some easily available parameters
that should be included in the estimation of the soil properties to
improve the prediction models. It is shown that the use of friction
ration in the estimation of Φ and the use of fines content in the
estimation of E considerable improve the prediction models.
Abstract: In this paper a novel design of aerostatic thrust bearing
is proposed and is analyzed numerically. The capillary restrictor and
bearing disk are made of elastomer like silicone and PU. The
viscoelasticity of elastomer helps the capillary expand for more air
flux and at the same time, allows conicity of the bearing surface to
form when the air pressure is enhanced. Therefore the bearing has the
better ability of passive compensation. In the present example, as
compared with the typical model, the new designs can nearly double
the load capability and offer four times static stiffness.