Abstract: As a technique that reduces variation in a product by lessening the sensitivity of the design to sources of variation, rather than by controlling their sources, Taguchi Robust Design entails the designing of ideal goods, by developing a product that has minimal variance in its characteristics and also meets the desired exact performance. This paper examined the concept of the manufacturing approach and its application to brake pad product of an automotive parts manufacturing company. Although the firm claimed that only defects, excess inventory, and over-production were the few wastes that grossly affect their productivity and profitability, a careful study and analysis of their manufacturing processes with the application of Single Minute Exchange of Dies (SMED) tool showed that the waste of waiting is the fourth waste that bedevils the firm. The selection of the Taguchi L9 orthogonal array which is based on the four parameters and the three levels of variation for each parameter revealed that with a range of 2.17, that waiting is the major waste that the company must reduce in order to continue to be viable. Also, to enhance the company’s throughput and profitability, the wastes of over-production, excess inventory, and defects with ranges of 2.01, 1.46, and 0.82, ranking second, third, and fourth respectively must also be reduced to the barest minimum. After proposing -33.84 as the highest optimum Signal-to-Noise ratio to be maintained for the waste of waiting, the paper advocated for the adoption of all the tools and techniques of Lean Production System (LPS), and Continuous Improvement (CI), and concluded by recommending SMED in order to drastically reduce set up time which leads to unnecessary waiting.
Abstract: Ball joints support and guide certain automotive parts that move relative to the frame of the vehicle. Such ball joints are covered and protected from dust, mud, and other interfering materials by ball-joint boots made of rubber—a flexible and near-incompressible material. The boots may experience twisting and bending deformations because of the motion of the joint arm. Thus, environmental and endurance tests of ball-joint boots apply both bending and twisting deformations. In this study, environmental and endurance testing was simulated via the finite element method performed by using a commercial software package. The ranges of principal stress and principal strain values that are known to directly affect the fatigue lives of the parts were sought. By defining these ranges, the number of iterative tests and modifications of the materials and dimensions of the boot can be decreased. Therefore, instead of performing actual part tests, manufacturers can perform standard fatigue tests in trials of different materials by applying only the defined range of stress or strain values.
Abstract: In this paper, a method is proposed for solving Fuzzy Multi-Objective Linear Programming problems (FMOLPP) with fuzzy right hand side and fuzzy decision variables. To illustrate the proposed method, it is applied to the problem of selecting suppliers for an automotive parts producer company in Iran in order to find the number of optimal orders allocated to each supplier considering the conflicting objectives. Finally, the obtained results are discussed.
Abstract: The purpose of this study is to develop a forging process of automotive parts that satisfies the deformation characteristics. The analyses of temperature variation and deformation behavior of the material are important to obtain the optimal forging products. The hot compression test was carried out to know formability at high temperature. In order to define the optimum forging conditions including material temperature, strain and forging load, the commercial finite element analysis code was used to simulate the forging procedure of engine mounting parts. Experimental results were compared with the simulation results by finite element analysis. Test results were in good agreement with the simulations.
Abstract: The purposes of this study were to: 1) investigate
operation conditions of SME automotive part industry in Bangkok
and vicinity and 2) to compare operation problem levels of SME
automotive part industry in Bangkok and vicinity according to the
sizes of the enterprises. Samples in this study included 196
entrepreneurs of SME automotive part industry in Bangkok and
vicinity derived from simple random sampling and calculation from
R. V. Krejcie and D. W. Morgan’s tables. Research statistics included
frequency, percentage, mean, standard deviation, and T-test. The
results revealed that in general the problem levels of SME automotive
part industry in Bangkok and vicinity were high. When considering
in details, it was found that the problem levels were high at every
aspect, i.e. personal, production, export, finance, and marketing
respectively. The comparison of the problem levels according to the
sizes of the enterprises revealed statistically significant differences at
.05. When considering on each aspect, it was found that the aspect
with the statistical difference at .05 included 5 aspects, i.e.
production, marketing, finance, personal, and export. The findings
also showed that small enterprises faced more severe problems than
those of medium enterprises.
Abstract: Machining parameters are very important in
determining the surface quality of any material. In the past decade,
some new engineering materials were developed for the
manufacturing industry which created a need to conduct an
investigation on the impact of the said parameters on their surface
roughness. Polyurethane (PU) block is widely used in the automotive
industry to manufacture parts such as checking fixtures that are used
to verify the dimensional accuracy of automotive parts. In this paper,
the design of experiment (DOE) was used to investigate on the effect
of the milling parameters on the PU block. Furthermore, an analysis
of the machined surface chemical composition was done using
scanning electron microscope (SEM). It was found that the surface
roughness of the PU block is severely affected when PU undergoes a
flood machining process instead of a dry condition. In addition the
stepover and the silicon content were found to be the most significant
parameters that influence the surface quality of the PU block.
Abstract: In recent years, global warming has become a
worldwide problem. The reduction of carbon dioxide emissions is a
top priority for many companies in the manufacturing industry. In the
automobile industry as well, the reduction of carbon dioxide emissions
is one of the most important issues. Technology to reduce the weight
of automotive parts improves the fuel economy of automobiles, and is
an important technology for reducing carbon dioxide. Also, even if
this weight reduction technology is applied to electric automobiles
rather than gasoline automobiles, reducing energy consumption
remains an important issue. Plastic processing of hollow pipes is one
important technology for realizing the weight reduction of automotive
parts. Ohashi et al. [1],[2] present an example of research on pipe
formation in which a process was carried out to enlarge a pipe
diameter using a lost core, achieving the suppression of wall thickness
reduction and greater pipe expansion than hydroforming.
In this study, we investigated a method to increase the wall
thickness of a pipe through pipe compression using planetary rolls.
The establishment of a technology whereby the wall thickness of a
pipe can be controlled without buckling the pipe is an important
technology for the weight reduction of products. Using the finite
element analysis method, we predicted that it would be possible to
increase the compression of an aluminum pipe with a 3mm wall
thickness by approximately 20%, and wall thickness by approximately
20% by pressing the hollow pipe with planetary rolls.
Abstract: In order to develop any strategy, it is essential to first
identify opportunities, threats, weak and strong points. Assessment of
technology level provides the possibility of concentrating on weak
and strong points. The results of technology assessment have a direct
effect on decision making process in the field of technology transfer
or expansion of internal research capabilities so it has a critical role
in technology management. This paper presents a conceptual model
to analyze the technology capability of a company as a whole and in
four main aspects of technology. This model was tested on 10
automotive parts manufacturers in IRAN. Using this model,
capability level of manufacturers was investigated in four fields of
managing aspects, hard aspects, human aspects, and information and
knowledge aspects. Results show that these firms concentrate on hard
aspect of technology while others aspects are poor and need to be
supported more. So this industry should develop other aspects of
technology as well as hard aspect to have effective and efficient use
of its technology. These paper findings are useful for the technology
planning and management in automotive part manufactures in IRAN
and other Industries which are technology followers and transport
their needed technologies.