Abstract: A new chelating resin is prepared by coupling Amberlite XAD-4 with 1-amino-2-naphthole through an azo spacer. The resulting sorbent has been characterized by FT-IR, elemental analysis and thermogravimetric analysis (TGA) and studied for preconcentrating of Fe (II) using flame atomic absorption spectrometry (FAAS) for metal monitoring. The optimum pH value for sorption of the iron ions was 6.5. The resin was subjected to evaluation through batch binding of mentioned metal ion. Quantitative desorption occurs instantaneously with 0.5 M HNO3. The sorption capacity was found 4.1 mmol.g-1 of resin for Fe (II) in the aqueous solution. The chelating resin can be reused for 10 cycles of sorption-desorption without any significant change in sorption capacity. A recovery of 97% was obtained the metal ions with 0.5 M HNO3 as eluting agent. The method was applied for metal ions determination from industrial waste water sample.
Abstract: A complete spectral representation for the
electromagnetic field of planar multilayered waveguides
inhomogeneously filled with omega media is presented. The problem
of guided electromagnetic propagation is reduced to an eigenvalue
equation related to a 2 ´ 2 matrix differential operator. Using the
concept of adjoint waveguide, general bi-orthogonality relations for
the hybrid modes (either from the discrete or from the continuous
spectrum) are derived. For the special case of homogeneous layers
the linear operator formalism is reduced to a simple 2 ´ 2 coupling
matrix eigenvalue problem. Finally, as an example of application, the
surface and the radiation modes of a grounded omega slab waveguide
are analyzed.
Abstract: In this study thermodynamic performance analysis of a
combined organic Rankine cycle and ejector refrigeration cycle is
carried out for use of low-grade heat source in the form of sensible
energy. Special attention is paid to the effects of system parameters
including the turbine inlet temperature and turbine inlet pressure on the
characteristics of the system such as ratios of mass flow rate, net work
production, and refrigeration capacity as well as the coefficient of
performance and exergy efficiency of the system. Results show that
for a given source the coefficient of performance increases with
increasing of the turbine inlet pressure. However, the exergy
efficiency has an optimal condition with respect to the turbine inlet
pressure.
Abstract: Many footbridges have natural frequencies that
coincide with the dominant frequencies of the pedestrian-induced
load and therefore they have a potential to suffer excessive vibrations
under dynamic loads induced by pedestrians. Some of the design
standards introduce load models for pedestrian loads applicable for
simple structures. Load modeling for more complex structures, on the
other hand, is most often left to the designer. The main focus of this
paper is on the human induced forces transmitted to a footbridge and
on the ways these loads can be modeled to be used in the dynamic
design of footbridges. Also design criteria and load models proposed
by widely used standards were introduced and a comparison was
made. The dynamic analysis of the suspension bridge in Kolin in the
Czech Republic was performed on detailed FEM model using the
ANSYS program system. An attempt to model the load imposed by a
single person and a crowd of pedestrians resulted in displacements
and accelerations that are compared with serviceability criteria.
Abstract: Business process model describes process flow of a
business and can be seen as the requirement for developing a
software application. This paper discusses a BPM2CD guideline
which complements the Model Driven Architecture concept by
suggesting how to create a platform-independent software model in
the form of a UML class diagram from a business process model. An
important step is the identification of UML classes from the business
process model. A technique for object-oriented analysis called
domain analysis is borrowed and key concepts in the business
process model will be discovered and proposed as candidate classes
for the class diagram. The paper enhances this step by using ontology
search to help identify important classes for the business domain. As
ontology is a source of knowledge for a particular domain which
itself can link to ontologies of related domains, the search can give a
refined set of candidate classes for the resulting class diagram.
Abstract: Deep and radical social reforms of the last century-s
nineties in many Eastern European countries caused changes in
Information Technology-s (IT) field. Inefficient information
technologies were rapidly replaced with forefront IT solutions, e.g.,
in Eastern European countries there is a high level penetration of
qualitative high-speed Internet. The authors have taken part in the
introduction of those changes in Latvia-s leading IT research
institute. Grounding on their experience authors in this paper offer an
IT services based model for analysis the mentioned changes- and
development processes in the higher education and research fields,
i.e., for research e-infrastructure-s development. Compare to the
international practice such services were developed in Eastern Europe
in an untraditional way, which provided swift and positive
technological changes.
Abstract: Sputum smear conversion after one month of antituberculosis
therapy in new smear positive pulmonary tuberculosis
patients (PTB+) is a vital indicator towards treatment success. The
objective of this study is to determine the rate of sputum smear
conversion in new PTB+ patients after one month under treatment of
National Institute of Diseases of the Chest and Hospital (NIDCH).
Analysis of sputum smear conversion was done by re-clinical
examination with sputum smear microscopic test after one month.
Socio-demographic and hematological parameters were evaluated to
perceive the correlation with the disease status. Among all enrolled
patients only 33.33% were available for follow up diagnosis and of
them only 42.86% patients turned to smear negative. Probably this
consequence is due to non-coherence to the proper disease
management. 66.67% and 78.78% patients reported low haemoglobin
and packed cell volume level respectively whereas 80% and 93.33%
patients accounted accelerated platelet count and erythrocyte
sedimentation rate correspondingly.
Abstract: This conference paper discusses a risk allocation problem for subprime investing banks involving investment in subprime structured mortgage products (SMPs) and Treasuries. In order to solve this problem, we develop a L'evy process-based model of jump diffusion-type for investment choice in subprime SMPs and Treasuries. This model incorporates subprime SMP losses for which credit default insurance in the form of credit default swaps (CDSs) can be purchased. In essence, we solve a mean swap-at-risk (SaR) optimization problem for investment which determines optimal allocation between SMPs and Treasuries subject to credit risk protection via CDSs. In this regard, SaR is indicative of how much protection investors must purchase from swap protection sellers in order to cover possible losses from SMP default. Here, SaR is defined in terms of value-at-risk (VaR). Finally, we provide an analysis of the aforementioned optimization problem and its connections with the subprime mortgage crisis (SMC).
Abstract: This paper presents the buckling analysis of short and
long functionally graded cylindrical shells under thermal and
mechanical loads. The shell properties are assumed to vary
continuously from the inner surface to the outer surface of the shell.
The equilibrium and stability equations are derived using the total
potential energy equations, Euler equations and first order shear
deformation theory assumptions. The resulting equations are solved
for simply supported boundary conditions. The critical temperature
and pressure loads are calculated for both short and long cylindrical
shells. Comparison studies show the effects of functionally graded
index, loading type and shell geometry on critical buckling loads of
short and long functionally graded cylindrical shells.
Abstract: Studies in neuroscience suggest that both global and
local feature information are crucial for perception and recognition of
faces. It is widely believed that local feature is less sensitive to
variations caused by illumination, expression and illumination. In
this paper, we target at designing and learning local features for face
recognition. We designed three types of local features. They are
semi-global feature, local patch feature and tangent shape feature.
The designing of semi-global feature aims at taking advantage of
global-like feature and meanwhile avoiding suppressing AdaBoost
algorithm in boosting weak classifies established from small local
patches. The designing of local patch feature targets at automatically
selecting discriminative features, and is thus different with traditional
ways, in which local patches are usually selected manually to cover
the salient facial components. Also, shape feature is considered in
this paper for frontal view face recognition. These features are
selected and combined under the framework of boosting algorithm
and cascade structure. The experimental results demonstrate that the
proposed approach outperforms the standard eigenface method and
Bayesian method. Moreover, the selected local features and
observations in the experiments are enlightening to researches in
local feature design in face recognition.
Abstract: Fuel and oxidant gas delivery plate, or fuel cell
plate, is a key component of a Proton Exchange Membrane (PEM)
fuel cell. To manufacture low-cost and high performance fuel cell
plates, advanced computer modeling and finite element structure
analysis are used as virtual prototyping tools for the optimization
of the plates at the early design stage. The present study examines
thermal stress analysis of the fuel cell plates that are produced
using a patented, low-cost fuel cell plate production technique
based on screen-printing. Design optimization is applied to
minimize the maximum stress within the plate, subject to strain
constraint with both geometry and material parameters as design
variables. The study reveals the characteristics of the printed
plates, and provides guidelines for the structure and material design
of the fuel cell plate.
Abstract: All practical real-time scheduling algorithms in multiprocessor systems present a trade-off between their computational complexity and performance. In real-time systems, tasks have to be performed correctly and timely. Finding minimal schedule in multiprocessor systems with real-time constraints is shown to be NP-hard. Although some optimal algorithms have been employed in uni-processor systems, they fail when they are applied in multiprocessor systems. The practical scheduling algorithms in real-time systems have not deterministic response time. Deterministic timing behavior is an important parameter for system robustness analysis. The intrinsic uncertainty in dynamic real-time systems increases the difficulties of scheduling problem. To alleviate these difficulties, we have proposed a fuzzy scheduling approach to arrange real-time periodic and non-periodic tasks in multiprocessor systems. Static and dynamic optimal scheduling algorithms fail with non-critical overload. In contrast, our approach balances task loads of the processors successfully while consider starvation prevention and fairness which cause higher priority tasks have higher running probability. A simulation is conducted to evaluate the performance of the proposed approach. Experimental results have shown that the proposed fuzzy scheduler creates feasible schedules for homogeneous and heterogeneous tasks. It also and considers tasks priorities which cause higher system utilization and lowers deadline miss time. According to the results, it performs very close to optimal schedule of uni-processor systems.
Abstract: This paper deals with a numerical analysis of the
transient response of composite beams with strain rate dependent
mechanical properties by use of a finite difference method. The
equations of motion based on Timoshenko beam theory are derived.
The geometric nonlinearity effects are taken into account with von
Kármán large deflection theory. The finite difference method in
conjunction with Newmark average acceleration method is applied to
solve the differential equations. A modified progressive damage
model which accounts for strain rate effects is developed based on
the material property degradation rules and modified Hashin-type
failure criteria and added to the finite difference model. The
components of the model are implemented into a computer code in
Mathematica 6. Glass/epoxy laminated composite beams with
constant and strain rate dependent mechanical properties under
dynamic load are analyzed. Effects of strain rate on dynamic
response of the beam for various stacking sequences, load and
boundary conditions are investigated.
Abstract: This paper presents a novel two-phase hybrid optimization algorithm with hybrid genetic operators to solve the optimal control problem of a single stage hybrid manufacturing system. The proposed hybrid real coded genetic algorithm (HRCGA) is developed in such a way that a simple real coded GA acts as a base level search, which makes a quick decision to direct the search towards the optimal region, and a local search method is next employed to do fine tuning. The hybrid genetic operators involved in the proposed algorithm improve both the quality of the solution and convergence speed. The phase–1 uses conventional real coded genetic algorithm (RCGA), while optimisation by direct search and systematic reduction of the size of search region is employed in the phase – 2. A typical numerical example of an optimal control problem with the number of jobs varying from 10 to 50 is included to illustrate the efficacy of the proposed algorithm. Several statistical analyses are done to compare the validity of the proposed algorithm with the conventional RCGA and PSO techniques. Hypothesis t – test and analysis of variance (ANOVA) test are also carried out to validate the effectiveness of the proposed algorithm. The results clearly demonstrate that the proposed algorithm not only improves the quality but also is more efficient in converging to the optimal value faster. They can outperform the conventional real coded GA (RCGA) and the efficient particle swarm optimisation (PSO) algorithm in quality of the optimal solution and also in terms of convergence to the actual optimum value.
Abstract: Biometric techniques are gaining importance for
personal authentication and identification as compared to the
traditional authentication methods. Biometric templates are
vulnerable to variety of attacks due to their inherent nature. When a
person-s biometric is compromised his identity is lost. In contrast to
password, biometric is not revocable. Therefore, providing security
to the stored biometric template is very crucial. Crypto biometric
systems are authentication systems, which blends the idea of
cryptography and biometrics. Fuzzy vault is a proven crypto
biometric construct which is used to secure the biometric templates.
However fuzzy vault suffer from certain limitations like nonrevocability,
cross matching. Security of the fuzzy vault is affected
by the non-uniform nature of the biometric data. Fuzzy vault when
hardened with password overcomes these limitations. Password
provides an additional layer of security and enhances user privacy.
Retina has certain advantages over other biometric traits. Retinal
scans are used in high-end security applications like access control to
areas or rooms in military installations, power plants, and other high
risk security areas. This work applies the idea of fuzzy vault for
retinal biometric template. Multimodal biometric system
performance is well compared to single modal biometric systems.
The proposed multi modal biometric fuzzy vault includes combined
feature points from retina and fingerprint. The combined vault is
hardened with user password for achieving high level of security.
The security of the combined vault is measured using min-entropy.
The proposed password hardened multi biometric fuzzy vault is
robust towards stored biometric template attacks.
Abstract: This paper proposed a stiffness analysis method for a
3-PRS mechanism for welding thick aluminum plate using FSW
technology. In the molding process, elastic deformation of lead-screws
and links are taken into account. This method is based on the virtual
work principle. Through a survey of the commonly used stiffness
performance indices, the minimum and maximum eigenvalues of the
stiffness matrix are used to evaluate the stiffness of the 3-PRS
mechanism. Furthermore, A FEA model has been constructed to verify
the method. Finally, we redefined the workspace using the stiffness
analysis method.
Abstract: Heat powered solid sorption is a feasible alternative to
electrical vapor compression refrigeration systems. In this paper,
activated carbon (powder type Maxsorb and fiber type ACF-A10)-
CO2 based adsorption cooling cycles are studied using the pressuretemperature-
concentration (P-T-W) diagram. The specific cooling
effect (SCE) and the coefficient of performance (COP) of these two
cooling systems are simulated for the driving heat source
temperatures ranging from 30 ºC to 90 ºC in terms of different
cooling load temperatures with a cooling source temperature of 25
ºC. It is found from the present analysis that Maxsorb-CO2 couple
shows higher cooling capacity and COP. The maximum COPs of
Maxsorb-CO2 and ACF(A10)-CO2 based cooling systems are found
to be 0.15 and 0.083, respectively. The main innovative feature of
this cooling cycle is the ability to utilize low temperature waste heat
or solar energy using CO2 as the refrigerant, which is one of the best
alternative for applications where flammability and toxicity are not
allowed.
Abstract: Control chart pattern recognition is one of the most important tools to identify the process state in statistical process control. The abnormal process state could be classified by the recognition of unnatural patterns that arise from assignable causes. In this study, a wavelet based neural network approach is proposed for the recognition of control chart patterns that have various characteristics. The procedure of proposed control chart pattern recognizer comprises three stages. First, multi-resolution wavelet analysis is used to generate time-shape and time-frequency coefficients that have detail information about the patterns. Second, distance based features are extracted by a bi-directional Kohonen network to make reduced and robust information. Third, a back-propagation network classifier is trained by these features. The accuracy of the proposed method is shown by the performance evaluation with numerical results.
Abstract: This paper introduces new algorithms (Fuzzy relative
of the CLARANS algorithm FCLARANS and Fuzzy c Medoids
based on randomized search FCMRANS) for fuzzy clustering of
relational data. Unlike existing fuzzy c-medoids algorithm (FCMdd)
in which the within cluster dissimilarity of each cluster is minimized
in each iteration by recomputing new medoids given current
memberships, FCLARANS minimizes the same objective function
minimized by FCMdd by changing current medoids in such away
that that the sum of the within cluster dissimilarities is minimized.
Computing new medoids may be effected by noise because outliers
may join the computation of medoids while the choice of medoids in
FCLARANS is dictated by the location of a predominant fraction of
points inside a cluster and, therefore, it is less sensitive to the
presence of outliers. In FCMRANS the step of computing new
medoids in FCMdd is modified to be based on randomized search.
Furthermore, a new initialization procedure is developed that add
randomness to the initialization procedure used with FCMdd. Both
FCLARANS and FCMRANS are compared with the robust and
linearized version of fuzzy c-medoids (RFCMdd). Experimental
results with different samples of the Reuter-21578, Newsgroups
(20NG) and generated datasets with noise show that FCLARANS is
more robust than both RFCMdd and FCMRANS. Finally, both
FCMRANS and FCLARANS are more efficient and their outputs
are almost the same as that of RFCMdd in terms of classification
rate.
Abstract: Dengue fever is an important human arboviral disease. Outbreaks are now reported quite often from many parts of the world. The number of cases involving pregnant women and infant cases are increasing every year. The illness is often severe and complications may occur. Deaths often occur because of the difficulties in early diagnosis and in the improper management of the diseases. Dengue antibodies from pregnant women are passed on to infants and this protects the infants from dengue infections. Antibodies from the mother are transferred to the fetus when it is still in the womb. In this study, we formulate a mathematical model to describe the transmission of this disease in pregnant women. The model is formulated by dividing the human population into pregnant women and non-pregnant human (men and non-pregnant women). Each class is subdivided into susceptible (S), infectious (I) and recovered (R) subclasses. We apply standard dynamical analysis to our model. Conditions for the local stability of the equilibrium points are given. The numerical simulations are shown. The bifurcation diagrams of our model are discussed. The control of this disease in pregnant women is discussed in terms of the threshold conditions.