Abstract: In this study, we consider a special situation that only a pair of hydrophone on a moving underwater vehicle is available to localize a fixed acoustic source of far distance. The trigonometry can be used in this situation by using two different DOA of different locations. Notice that the distance between the two locations should be measured. Therefore, we assume that the vehicle is sailing straightly and the moving distance for each unit time is measured continuously. However, the accuracy of the localization using the trigonometry is highly dependent to the accuracy of DOAs and measured moving distances. Therefore, we proposed another method based on the extended Kalman filter that gives more robust and accurate localization result.
Abstract: This paper presents an experimental investigation using Acoustic Emission (AE) technology to monitor sand transportation in multiphase flow. The investigations were undertaken on three-phase (air-water-sand) flow in a horizontal pipe where the superficial gas velocity (VSG) had a range of between 0.2msˉ¹ to 2.0msˉ¹ and superficial liquid velocity (VSL) had a range of between 0.2msˉ¹ to 1.0msˉ¹. The experimental findings clearly show a correlation exists between AE energy levels, sand concentration, superficial gas velocity (VSG), and superficial liquid velocity (VSL).
Abstract: Thermoacoustic instabilities in combustors have
remained a topic of investigation for over a few decades due to the
challenges it posses to the operation of low emission gas turbines.
For combustors burning liquid fuel, understanding the cause-andeffect
relationship between spray combustion dynamics and
thermoacoustic oscillations is imperative for the successful
development of any control methodology for its mitigation. The
paper presents some very unique operating characteristics of a
kerosene-fueled diffusion type combustor undergoing limit-cycle
oscillations. Combustor stability limits were mapped using three
different-sized injectors. The results show that combustor instability
depends on the characteristics of the fuel spray. A simple analytic
analysis is also reported in support of a plausible explanation for the
unique combustor behavior. The study indicates that high amplitude
acoustic pressure in the combustor may cause secondary breakdown
of fuel droplets resulting in premixed pre-vaporized type burning of
the diffusion type combustor.
Abstract: A novel robust audio watermarking scheme is
proposed in this paper. In the proposed scheme, the host audio signals
are segmented into frames. Two consecutive frames are assessed if
they are suitable to represent a watermark bit. If so, frequency
transform is performed on these two frames. The compressionexpansion
technique is adopted to generate distortion over the two
frames. The distortion is used to represent one watermark bit.
Psychoacoustic model is applied to calculate local auditory mask to
ensure that the distortion is not audible. The watermarking schemes
using mono and stereo audio signals are designed differently. The
correlation-based detection method is used to detect the distortion
and extract embedded watermark bits. The experimental results show
that the quality degradation caused by the embedded watermarks is
perceptually transparent and the proposed schemes are very robust
against different types of attacks.
Abstract: This paper presents how the real-time chatter
prevention can be realized by feedback of acoustic cutting signal, and
the efficacy of the proposed adaptive spindle speed tuning algorithm is
verified by intensive experimental simulations. A pair of
microphones, perpendicular to each other, is used to acquire the
acoustic cutting signal resulting from milling chatter. A real-time
feedback control loop is constructed for spindle speed compensation
so that the milling process can be ensured to be within the stability
zone of stability lobe diagram. Acoustic Chatter Signal Index (ACSI)
and Spindle Speed Compensation Strategy (SSCS) are proposed to
quantify the acoustic signal and actively tune the spindle speed
respectively. By converting the acoustic feedback signal into ACSI,
an appropriate Spindle Speed Compensation Rate (SSCR) can be
determined by SSCS based on real-time chatter level or ACSI.
Accordingly, the compensation command, referred to as Added-On
Voltage (AOV), is applied to increase/decrease the spindle motor
speed. By inspection on the precision and quality of the workpiece
surface after milling, the efficacy of the real-time chatter prevention
strategy via acoustic signal feedback is further assured.
Abstract: This paper investigates vortex shedding processes
occurring at the end of a stack of parallel plates, due to an oscillating
flow induced by an acoustic standing wave within an acoustic
resonator. Here, Particle Image Velocimetry (PIV) is used to quantify
the vortex shedding processes within an acoustic cycle
phase-by-phase, in particular during the “ejection" of the fluid out of
the stack. Standard hot-wire anemometry measurement is also applied
to detect the velocity fluctuations near the end of the stack.
Combination of these two measurement techniques allowed a detailed
analysis of the vortex shedding phenomena. The results obtained show
that, as the Reynolds number varies (by varying the plate thickness
and drive ratio), different flow patterns of vortex shedding are
observed by the PIV measurement. On the other hand, the
time-dependent hot-wire measurements allow obtaining detailed
frequency spectra of the velocity signal, used for calculating
characteristic Strouhal numbers. The impact of the plate thickness and
the Reynolds number on the vortex shedding pattern has been
discussed. Furthermore, a detailed map of the relationship between the
Strouhal number and Reynolds number has been obtained and
discussed.
Abstract: Large full frequency band gaps of surface and bulk
acoustic waves in two-dimensional phononic band structures with
hollow cylinders are addressed in this paper. It is well-known that
absolute frequency band gaps are difficultly obtained in a band
structure consisted of low-acoustic-impedance cylinders in
high-acoustic-impedance host materials such as PMMA/Ni band
structures. Phononic band structures with hollow cylinders are
analyzed and discussed to obtain large full frequency band gaps not
only for bulk modes but also for surface modes. The tendency of
absolute frequency band gaps of surface and bulk acoustic waves is
also addressed by changing the inner radius of hollow cylinders in this
paper. The technique and this kind of band structure are useful for
tuning the frequency band gaps and the design of acoustic waveguides.
Abstract: In this paper, a new adaptive Fourier decomposition
(AFD) based time-frequency speech analysis approach is proposed.
Given the fact that the fundamental frequency of speech signals often
undergo fluctuation, the classical short-time Fourier transform (STFT)
based spectrogram analysis suffers from the difficulty of window size
selection. AFD is a newly developed signal decomposition theory. It is
designed to deal with time-varying non-stationary signals. Its
outstanding characteristic is to provide instantaneous frequency for
each decomposed component, so the time-frequency analysis becomes
easier. Experiments are conducted based on the sample sentence in
TIMIT Acoustic-Phonetic Continuous Speech Corpus. The results
show that the AFD based time-frequency distribution outperforms the
STFT based one.
Abstract: In this study acoustic emission (AE) signals obtained during deformation and fracture of two types of ferrite-martensite dual phase steels (DPS) specimens have been analyzed in frequency domain. For this reason two low carbon steels with various amounts of carbon were chosen, and intercritically heat treated. In the introduced method, identifying the mechanisms of failure in the various phases of DPS is done. For this aim, AE monitoring has been used during tensile test of several DPS with various volume fraction of the martensite (VM) and attempted to relate the AE signals and failure mechanisms in these steels. Different signals, which referred to 2-3 micro-mechanisms of failure due to amount of carbon and also VM have been seen. By Fast Fourier Transformation (FFT) of signals in distinct locations, an excellent relationship between peak frequencies in these areas and micro-mechanisms of failure were seen. The results were verified by microscopic observations (SEM).
Abstract: In this paper, an algorithm for detecting and attenuating
puff noises frequently generated under the mobile environment is
proposed. As a baseline system, puff detection system is designed
based on Gaussian Mixture Model (GMM), and 39th Mel Frequency
Cepstral Coefficient (MFCC) is extracted as feature parameters. To
improve the detection performance, effective acoustic features for puff
detection are proposed. In addition, detected puff intervals are
attenuated by high-pass filtering. The speech recognition rate was
measured for evaluation and confusion matrix and ROC curve are used
to confirm the validity of the proposed system.
Abstract: Computerized lip reading has been one of the most
actively researched areas of computer vision in recent past because
of its crime fighting potential and invariance to acoustic environment.
However, several factors like fast speech, bad pronunciation,
poor illumination, movement of face, moustaches and beards make
lip reading difficult. In present work, we propose a solution for
automatic lip contour tracking and recognizing letters of English
language spoken by speakers using the information available from
lip movements. Level set method is used for tracking lip contour
using a contour velocity model and a feature vector of lip movements
is then obtained. Character recognition is performed using modified
k nearest neighbor algorithm which assigns more weight to nearer
neighbors. The proposed system has been found to have accuracy
of 73.3% for character recognition with speaker lip movements as
the only input and without using any speech recognition system in
parallel. The approach used in this work is found to significantly
solve the purpose of lip reading when size of database is small.
Abstract: The modeling of sound radiation is of fundamental importance for understanding the propagation of acoustic waves and, consequently, develop mechanisms for reducing acoustic noise. The propagation of acoustic waves, are involved in various phenomena such as radiation, absorption, transmission and reflection. The radiation is studied through the linear equation of the acoustic wave that is obtained through the equation for the Conservation of Momentum, equation of State and Continuity. From these equations, is the Helmholtz differential equation that describes the problem of acoustic radiation. In this paper we obtained the solution of the Helmholtz differential equation for an infinite cylinder in a pulsating through free and homogeneous. The analytical solution is implemented and the results are compared with the literature. A numerical formulation for this problem is obtained using the Boundary Element Method (BEM). This method has great power for solving certain acoustical problems in open field, compared to differential methods. BEM reduces the size of the problem, thereby simplifying the input data to be worked and reducing the computational time used.
Abstract: This article is devoted to the numerical solution of
large-scale quadratic eigenvalue problems. Such problems arise in
a wide variety of applications, such as the dynamic analysis of
structural mechanical systems, acoustic systems, fluid mechanics,
and signal processing. We first introduce a generalized second-order
Krylov subspace based on a pair of square matrices and two initial
vectors and present a generalized second-order Arnoldi process for
constructing an orthonormal basis of the generalized second-order
Krylov subspace. Then, by using the projection technique and the
refined projection technique, we propose a restarted generalized
second-order Arnoldi method and a restarted refined generalized
second-order Arnoldi method for computing some eigenpairs of largescale
quadratic eigenvalue problems. Some theoretical results are also
presented. Some numerical examples are presented to illustrate the
effectiveness of the proposed methods.
Abstract: A state of the art Speaker Identification (SI) system
requires a robust feature extraction unit followed by a speaker
modeling scheme for generalized representation of these features.
Over the years, Mel-Frequency Cepstral Coefficients (MFCC)
modeled on the human auditory system has been used as a standard
acoustic feature set for speech related applications. On a recent
contribution by authors, it has been shown that the Inverted Mel-
Frequency Cepstral Coefficients (IMFCC) is useful feature set for
SI, which contains complementary information present in high
frequency region. This paper introduces the Gaussian shaped filter
(GF) while calculating MFCC and IMFCC in place of typical
triangular shaped bins. The objective is to introduce a higher
amount of correlation between subband outputs. The performances
of both MFCC & IMFCC improve with GF over conventional
triangular filter (TF) based implementation, individually as well as
in combination. With GMM as speaker modeling paradigm, the
performances of proposed GF based MFCC and IMFCC in
individual and fused mode have been verified in two standard
databases YOHO, (Microphone Speech) and POLYCOST
(Telephone Speech) each of which has more than 130 speakers.
Abstract: Ultrasound is useful in demonstrating bone mineral
density of regenerating osseous tissue as well as structural alterations.
A proposed ultrasound method, which included ultrasonography and
acoustic parameters measurement, was employed to evaluate its
efficacy in monitoring the bone callus changes in a rabbit tibial
distraction osteogenesis (DO) model.
The findings demonstrated that ultrasonographic images depicted
characteristic changes of the bone callus, typical of histology findings,
during the distraction phase. Follow-up acoustic parameters
measurement of the bone callus, including speed of sound, reflection
and attenuation, showed significant linear changes over time during
the distraction phase. The acoustic parameters obtained during the
distraction phase also showed moderate to strong correlation with
consolidated bone callus density and micro-architecture measured by
micro-computed tomography at the end of the consolidation phase.
The results support the preferred use of ultrasound imaging in the
early monitoring of bone callus changes during DO treatment.
Abstract: An array of piezoelectric micro actuators can be used
for radiation of an ultrasonic carrier signal modulated in amplitude
with an acoustic signal, which yields audio frequency applications as
the air acts as a self-demodulating medium. This application is
known as the parametric array. We propose a parametric array with
array elements based on existing piezoelectric micro ultrasonic
transducer (pMUT) design techniques. In order to reach enough
acoustic output power at a desired operating frequency, a proper ratio
between number of array elements and array size needs to be used,
with an array total area of the order of one cm square. The
transducers presented are characterized via impedance, admittance,
noise figure, transducer gain and frequency responses.
Abstract: This paper attempts to explain response components of Electrovestibulography (EVestG) using a computer simulation of a three-canal model of the vestibular system. EVestG is a potentially new diagnostic method for Meniere's disease. EVestG is a variant of Electrocochleography (ECOG), which has been used as a standard method for diagnosing Meniere's disease - it can be used to measure the SP/AP ratio, where an SP/AP ratio greater than 0.4-0.5 is indicative of Meniere-s Disease. In EVestG, an applied head tilt replaces the acoustic stimulus of ECOG. The EVestG output is also an SP/AP type plot, where SP is the summing potential, and AP is the action potential amplitude. AP is thought of as being proportional to the size of a population of afferents in an excitatory neural firing state. A simulation of the fluid volume displacement in the vestibular labyrinth in response to various types of head tilts (ipsilateral, backwards and horizontal rotation) was performed, and a simple neural model based on these simulations developed. The simple neural model shows that the change in firing rate of the utricle is much larger in magnitude than the change in firing rates of all three semi-circular canals following a head tilt (except in a horizontal rotation). The data suggests that the change in utricular firing rate is a minimum 2-3 orders of magnitude larger than changes in firing rates of the canals during ipsilateral/backward tilts. Based on these results, the neural response recorded by the electrode in our EVestG recordings is expected to be dominated by the utricle in ipsilateral/backward tilts (It is important to note that the effect of the saccule and efferent signals were not taken into account in this model). If the utricle response dominates the EVestG recordings as the modeling results suggest, then EVestG has the potential to diagnose utricular hair cell damage due to a viral infection (which has been cited as one possible cause of Meniere's Disease).
Abstract: The paper reports on the results of experimental and
numerical study of nonstationary swirling flow in an isothermal
model of vortex burner. It has been identified that main source of the
instability is related to a precessing vortex core (PVC) phenomenon.
The PVC induced flow pulsation characteristics such as precession
frequency and its variation as a function of flowrate and swirl number
have been explored making use of acoustic probes. Additionally
pressure transducers were used to measure the pressure drops on the
working chamber and across the vortex flow. The experiments have
been included also the mean velocity measurements making use of a
laser-Doppler anemometry. The features of instantaneous flowfield
generated by the PVC were analyzed employing a commercial CFD
code (Star-CCM+) based on Detached Eddy Simulation (DES)
approach. Validity of the numerical code has been checked by
comparison calculated flowfield data with the obtained experimental
results. It has been confirmed particularly that the CFD code applied
correctly reproduces the flow features.
Abstract: We have considered an unmagnetized dusty plasma system consisting of ions obeying superthermal distribution and strongly coupled negatively charged dust. We have used reductive perturbation method and derived the Kordeweg-de Vries-Burgers (KdV-Burgers) equation. The behavior of the shock waves in the plasma has been investigated.
Abstract: An emotional speech recognition system for the
applications on smart phones was proposed in this study to combine
with 3G mobile communications and social networks to provide users
and their groups with more interaction and care. This study developed
a mechanism using the support vector machines (SVM) to recognize
the emotions of speech such as happiness, anger, sadness and normal.
The mechanism uses a hierarchical classifier to adjust the weights of
acoustic features and divides various parameters into the categories of
energy and frequency for training. In this study, 28 commonly used
acoustic features including pitch and volume were proposed for
training. In addition, a time-frequency parameter obtained by
continuous wavelet transforms was also used to identify the accent and
intonation in a sentence during the recognition process. The Berlin
Database of Emotional Speech was used by dividing the speech into
male and female data sets for training. According to the experimental
results, the accuracies of male and female test sets were increased by
4.6% and 5.2% respectively after using the time-frequency parameter
for classifying happy and angry emotions. For the classification of all
emotions, the average accuracy, including male and female data, was
63.5% for the test set and 90.9% for the whole data set.