Abstract: Emission regulations for diesel engines are being strengthened and it is impossible to meet the standards without exhaust after-treatment systems. Lack of the space in many diesel vehicles, however, make it difficult to design and install stand-alone catalytic converters such as DOC, DPF, and SCR in the vehicle exhaust systems. Accordingly, those have been installed inside the muffler to save the space, and referred to the catalytic muffler. However, that has complex internal structure with perforated plate and pipe for noise and monolithic catalyst for emission reduction. For this reason, flow uniformity and pressure drop, which affect efficiency of catalyst and engine performance, respectively, should be examined when the catalytic muffler is designed. In this work, therefore, the flow uniformity and pressure drop to improve the performance of the catalytic converter and the engine have been numerically investigated by changing various design parameters such as inlet shape, porosity, and outlet shape of the muffler using the three-dimensional turbulent flow of the incompressible, non-reacting, and steady state inside the catalytic muffler. Finally, it can be found that the shape, in which the muffler has perforated pipe inside the inlet part, has higher uniformity index and lower pressure drop than others considered in this work.
Abstract: An innovative design for intelligent Chemical Mechanical Polishing (CMP) system is proposed and verified by experiments in this report. On-line measurement and real-time feedback are integrated to eliminate the shortcomings of traditional approaches, e.g., the batch-to-batch discrepancy of required polishing time, over consumption of chemical slurry, and non-uniformity across the wafer. The major advantage of the proposed method is that the finish of local surface roughness can be consistent, no matter where the inner-ring region or outer-ring region is concerned. Secondly, it is able to eliminate the Edge effect. Conventionally, the interfacial induced stress near the wafer edge is generally much higher than that near the wafer center. At last, by using the proposed intelligent chemical mechanical polishing strategy, the cost of the entire machining cycle can be much reduced while the quality of the finished goods certainly upgraded.
Abstract: Charge Simulation Method (CSM) is one of the very widely used numerical field computation technique in High Voltage (HV) engineering. The high voltage fields of varying non uniformities are encountered in practice. CSM programs being case specific, the simulation accuracies heavily depend on the user (programmers) experience. Here is an effort to understand CSM errors and evolve some guidelines to setup accurate CSM models, relating non uniformities with assignment factors. The results are for the six-point-charge model of sphere-plane gap geometry. Using genetic algorithm (GA) as tool, optimum assignment factors at different non uniformity factors for this model have been evaluated and analyzed. It is shown that the symmetrically placed six-point-charge models can be good enough to set up CSM programs with potential errors less than 0.1% when the field non uniformity factor is greater than 2.64 (field utilization factor less than 52.76%).
Abstract: Preparation of size controlled nano-particles of silver catalyst on carbon substrate from e-waste has been investigated. Chemical route was developed by extraction of the metals available in nitric acid followed by treatment with hydrofluoric acid. Silver metal particles deposited with an average size 4-10 nm. A stabilizer concentration of 10- 40 g/l was used. The average size of the prepared silver decreased with increase of the anode current density. Size uniformity of the silver nano-particles was improved distinctly at higher current density no more than 20mA... Grain size increased with EK time whereby aggregation of particles was observed after 6 h of reaction.. The chemical method involves adsorption of silver nitrate on the carbon substrate. Adsorbed silver ions were directly reduced to metal particles using hydrazine hydrate. Another alternative method is by treatment with ammonia followed by heating the carbon loaded-silver hydroxide at 980°C. The product was characterized with the help of XRD, XRF, ICP, SEM and TEM techniques.
Abstract: Banyan networks are really attractive for serving as
the optical switching architectures due to their unique properties of
small depth and absolute signal loss uniformity. The fact has been
established that the limitations of blocking nature and the nonavailability
of proper connections due to non-rearrangeable property
can be easily ruled out using electro-optic MZI switches as basic
switching elements. Combination of the horizontal expansion and
vertical stacking of optical banyan networks is an appropriate scheme
for constructing non-blocking banyan-based optical switching
networks. The interconnected banyan switching fabrics (IBSF) have
been considered and analyzed to best serve the purpose of optical
switching with electro-optic MZI basic elements. The cross/bar state
interchange for the switches has been facilitated by appropriate
voltage switching or the by the switching of operating wavelength.
The paper is dedicated to the modification of the basic switching
element being used as well as the architecture of the switching
network.
Abstract: The paper presents an optimization study based on
genetic algorithms (GA-s) for a radio-frequency applicator used in
heating dielectric band products. The weakly coupled electro-thermal
problem is analyzed using 2D-FEM. The design variables in the
optimization process are: the voltage of a supplementary “guard"
electrode and six geometric parameters of the applicator. Two
objective functions are used: temperature uniformity and total active
power absorbed by the dielectric. Both mono-objective and multiobjective
formulations are implemented in GA optimization.
Abstract: Riprap is mostly used to prevent erosion by flows
down the steep slopes in river engineering. A total of 53 stability tests
performed on angular riprap with a median stone size ranging from
15 to 278 mm and slope ranging from 1 to 40% are used in this study.
The existing equations for the prediction of medium size of angular
stones are checked for their accuracy using the available data.
Predictions of median size using these equations are not satisfactory
and results show deviation by more than ±20% from the observed
values. A multivariable power regression analysis is performed to
propose a new equation relating the median size with unit discharge,
bed slope, riprap thickness and coefficient of uniformity. The
proposed relationship satisfactorily predicts the median angular stone
size with ±20% error. Further, the required size of the rounded stone
is more than the angular stone for the same unit discharge and the
ratio increases with unit discharge and also with embankment slope
of the riprap.
Abstract: Nowadays, fluidized bed plays an important part in industry. The design of this kind of reactor requires knowing the interfacial area between two phases and this interfacial area leads to calculate the solid holdup in the bed. Consequently achieving interfacial area between gas and solid in the bed experimentally is so significant. On interfacial area measurement in fluidized bed with gas has been worked, but light transmission technique has been used less. Therefore, in the current research the possibility of using of this technique and its accuracy are investigated. Measuring, a fluidized bed was designed and the problems were averted as far as possible. By using fine solid with equal shape and diameter and installing an optical system, the absorption of light during the time of fluidization has been measured. Results indicate that this method that its validity has been proved in the gas-liquid system, by different reasons have less application in gas-solid system. One important reason could be non-uniformity in such systems.
Abstract: Aircraft propulsion systems often use Y-shaped
subsonic diffusing ducts as twin air-intakes to supply the ambient air
into the engine compressor for thrust generation. Due to space
constraint, the diffusers need to be curved, which causes severe flow
non-uniformity at the engine face. The present study attempt to
control flow in a mild-curved Y-duct diffuser using trapezoidalshaped
vortex generators (VG) attached on either both the sidewalls
or top and bottom walls of the diffuser at the inflexion plane. A
commercial computational fluid dynamics (CFD) code is modified
and is used to simulate the effects of SVG in flow of a Y-duct
diffuser. A few experiments are conducted for CFD code validation,
while the rest are done computationally. The best combination of Yduct
diffuser is found with VG-2 arranged in co-rotating sequence
and attached to both the sidewalls, which ensures highest static
pressure recovery, lowest total pressure loss, minimum flow
distortion and less flow separation in Y-duct diffuser. The decrease in
VG height while attached to top and bottom walls further improves
axial flow uniformity at the diffuser outlet by a great margin as
compared to the bare duct.
Abstract: Quaternary InxAlyGa1-x-yN semiconductors have
attracted much research interest because the use of this quaternary
offer the great flexibility in tailoring their band gap profile while
maintaining their lattice-matching and structural integrity. The
structural and optical properties of InxAlyGa1-x-yN alloys grown by
molecular beam epitaxy (MBE) is presented. The structural quality of
InxAlyGa1-x-yN layers was characterized using high-resolution X-ray
diffraction (HRXRD). The results confirm that the InxAlyGa1-x-yN
films had wurtzite structure and without phase separation. As the In
composition increases, the Bragg angle of the (0002) InxAlyGa1-x-yN
peak gradually decreases, indicating the increase in the lattice constant
c of the alloys. FWHM of (0002) InxAlyGa1-x-yN decreases with
increasing In composition from 0 to 0.04, that could indicate the
decrease of quality of the samples due to point defects leading to
non-uniformity of the epilayers. UV-VIS spectroscopy have been used
to study the energy band gap of InxAlyGa1-x-yN. As the indium (In)
compositions increases, the energy band gap decreases. However, for
InxAlyGa1-x-yN with In composition of 0.1, the band gap shows a
sudden increase in energy. This is probably due to local alloy
compositional fluctuations in the epilayer. The bowing parameter
which appears also to be very sensitive on In content is investigated
and obtained b = 50.08 for quaternary InxAlyGa1-x-yN alloys. From
photoluminescence (PL) measurement, green luminescence (GL)
appears at PL spectrum of InxAlyGa1-x-yN, emitted for all x at ~530 nm
and it become more pronounced as the In composition (x) increased,
which is believed cause by gallium vacancies and related to isolated
native defects.
Abstract: This paper presents an experimental investigation of
transformer dielectric response and solid insulation water content.
The dielectric response was carried out on the base of Hybrid
Frequency Dielectric Spectroscopy and Polarization Current
measurements method (FDS &PC). The calculation of the water
content in paper is based on the water content in oil and the obtained
equilibrium curves. A reference measurements were performed at
equilibrium conditions for water content in oil and paper of
transformer at different stable temperatures (25, 50, 60 and 70°C) to
prepare references to evaluate the insulation behavior at the not
equilibrium conditions. Some measurements performed at the
different simulated normal working modes of transformer operation
at the same temperature where the equilibrium conditions. The
obtained results show that when transformer temperature is mach
more than the its ambient temperature, the transformer temperature
decreases immediately after disconnecting the transformer from the
network and this temperature reduction influences the transformer
insulation condition in the measuring process. In addition to the oil
temperature at the near places to the sensors, the temperature
uniformity in transformer which can be changed by a big change in
the load of transformer before the measuring time will influence the
result. The investigations have shown that the extremely influence of
the time between disconnecting the transformer and beginning the
measurements on the results. And the online monitoring for water
content in paper measurements, on the basis of the oil water content
on line monitoring and the obtained equilibrium curves. The
measurements where performed continuously and for about 50 days
without any disconnection in the prepared the adiabatic room.
Abstract: The electrolyte stirring method of anodization etching
process for manufacturing porous silicon (PS) is reported in this work.
Two experimental setups of nature air stirring (PS-ASM) and
electrolyte stirring (PS-ESM) are employed to clarify the influence of
stirring mechanisms on electrochemical etching process. Compared to
traditional fabrication without any stirring apparatus (PS-TM), a large
plateau region of PS surface structure is obtained from samples with
both stirring methods by the 3D-profiler measurement. Moreover, the
light emission response is also improved by both proposed electrolyte
stirring methods due to the cycling force in electrolyte could
effectively enhance etch-carrier distribution while the electrochemical
etching process is made. According to the analysis of statistical
calculation of photoluminescence (PL) intensity, lower standard
deviations are obtained from PS-samples with studied stirring methods,
i.e. the uniformity of PL-intensity is effectively improved. The
calculated deviations of PL-intensity are 93.2, 74.5 and 64,
respectively, for PS-TM, PS-ASM and PS-ESM.
Abstract: Technology of thin film deposition is of interest in
many engineering fields, from electronic manufacturing to corrosion
protective coating. A typical deposition process, like that developed
at the University of Eindhoven, considers the deposition of a thin,
amorphous film of C:H or of Si:H on the substrate, using the
Expanding Thermal arc Plasma technique. In this paper a computing
procedure is proposed to simulate the flow field in a deposition
chamber similar to that at the University of Eindhoven and a
sensitivity analysis is carried out in terms of: precursor mass flow
rate, electrical power, supplied to the torch and fluid-dynamic
characteristics of the plasma jet, using different nozzles. To this
purpose a deposition chamber similar in shape, dimensions and
operating parameters to the above mentioned chamber is considered.
Furthermore, a method is proposed for a very preliminary evaluation
of the film thickness distribution on the substrate. The computing
procedure relies on two codes working in tandem; the output from
the first code is the input to the second one. The first code simulates
the flow field in the torch, where Argon is ionized according to the
Saha-s equation, and in the nozzle. The second code simulates the
flow field in the chamber. Due to high rarefaction level, this is a
(commercial) Direct Simulation Monte Carlo code. Gas is a mixture
of 21 chemical species and 24 chemical reactions from Argon plasma
and Acetylene are implemented in both codes. The effects of the
above mentioned operating parameters are evaluated and discussed
by 2-D maps and profiles of some important thermo-fluid-dynamic
parameters, as per Mach number, velocity and temperature. Intensity,
position and extension of the shock wave are evaluated and the
influence of the above mentioned test conditions on the film
thickness and uniformity of distribution are also evaluated.
Abstract: This article provides partial evaluation index and its
standard of sports aerobics, including the following 12 indexes: health
vitality, coordination, flexibility, accuracy, pace, endurance, elasticity,
self-confidence, form, control, uniformity and musicality. The
three-layer BP artificial neural network model including input layer,
hidden layer and output layer is established. The result shows that the
model can well reflect the non-linear relationship between the
performance of 12 indexes and the overall performance. The predicted
value of each sample is very close to the true value, with a relative
error fluctuating around of 5%, and the network training is successful.
It shows that BP network has high prediction accuracy and good
generalization capacity if being applied in sports aerobics performance
evaluation after effective training.
Abstract: This paper describes the development of a 16-ports optical code division multiple access (OCDMA) encoder prototype based on Arrayed Waveguide Grating (AWG) and optical switches. It is potentially to provide a high security for data transmission due to all data will be transmitted in binary code form. The output signals from AWG are coded with a binary code that given to an optical switch before it signal modulate with the carrier and transmitted to the receiver. The 16-ports encoder used 16 double pole double throw (DPDT) toggle switches to control the polarization of voltage source from +5 V to -5 V for 16 optical switches. When +5 V is given, the optical switch will give code '1' and vice versa. The experimental results showed the insertion loss, crosstalk, uniformity, and optical signal-noise-ratio (OSNR) for the developed prototype are
Abstract: In conventional seedling production, the seedlings are
being grown in the open field under natural conditions. Here they are
susceptible to sudden changes in climate were their quality and yield
is affected. Quality seedlings are essential for good growth and
performance of crops in main field; they serve as a foundation for the
economic returns to the farmer. Producing quality seedling demands
usage of hybrid seeds as they have the ability to result in better yield,
greater uniformity, improved color, disease resistance, and so forth.
Hybrid seed production poses major operational challenge and its
seed use efficiency plays an important role. Thus in order to
overcome the difficulties currently present in conventional seedling
production and to efficiently use hybrid seeds, ITC Limited Agri
Business Divisions - Sustainability Cell as conceptualized a novel
method of seedling production unit for farmers in West Godavari
District of Andhra Pradesh. The “Green House based Float Seedling"
methodology aims at a protected cultivation technique wherein the
micro climate surrounding the plant/seedling body is controlled
partially or fully as per the requirement of the species. This paper
reports on the techno economic evaluation of green house for
cultivation of float based seedling production with experimental
results that was attained from the pilot implementation in West
Godavari District, Rajahmundry region of India.
Abstract: High Strength Concrete (HSC) is defined as concrete
that meets special combination of performance and uniformity
requirements that cannot be achieved routinely using conventional
constituents and normal mixing, placing, and curing procedures. It is
a highly complex material, which makes modeling its behavior a very
difficult task. This paper aimed to show possible applicability of
Neural Networks (NN) to predict the slump in High Strength
Concrete (HSC). Neural Network models is constructed, trained and
tested using the available test data of 349 different concrete mix
designs of High Strength Concrete (HSC) gathered from a particular
Ready Mix Concrete (RMC) batching plant. The most versatile
Neural Network model is selected to predict the slump in concrete.
The data used in the Neural Network models are arranged in a format
of eight input parameters that cover the Cement, Fly Ash, Sand,
Coarse Aggregate (10 mm), Coarse Aggregate (20 mm), Water,
Super-Plasticizer and Water/Binder ratio. Furthermore, to test the
accuracy for predicting slump in concrete, the final selected model is
further used to test the data of 40 different concrete mix designs of
High Strength Concrete (HSC) taken from the other batching plant.
The results are compared on the basis of error function (or
performance function).
Abstract: Professions are concerned about the public image they
have, and this public image is represented by stereotypes. Research is
needed to understand how accountants are perceived by different
actors in the society in different contexts, which would allow
universities, professional bodies and employers to adjust their
strategies to attract the right people to the profession and their
organizations. We aim to develop in this paper a framework to be
used in empirical testing in different environments to determine and
analyze the accountant-s stereotype. This framework will be useful in
analyzing the nuances associated to the accountant-s image and in
understanding the factors that may lead to uniformity in the
profession and of those leading to diversity from one context
(country, type of countries, region) to another.
Abstract: The purpose of this work is measurement of the
system presampling MTF of a variable resolution x-ray (VRX) CT
scanner. In this paper, we used the parameters of an actual VRX CT
scanner for simulation and study of effect of different focal spot sizes
on system presampling MTF by Monte Carlo method (GATE
simulation software). Focal spot size of 0.6 mm limited the spatial
resolution of the system to 5.5 cy/mm at incident angles of below 17º
for cell#1. By focal spot size of 0.3 mm the spatial resolution
increased up to 11 cy/mm and the limiting effect of focal spot size
appeared at incident angles of below 9º. The focal spot size of 0.3
mm could improve the spatial resolution to some extent but because
of magnification non-uniformity, there is a 10 cy/mm difference
between spatial resolution of cell#1 and cell#256. The focal spot size
of 0.1 mm acted as an ideal point source for this system. The spatial
resolution increased to more than 35 cy/mm and at all incident angles
the spatial resolution was a function of incident angle. By the way
focal spot size of 0.1 mm minimized the effect of magnification nonuniformity.
Abstract: Infrared focal plane arrays (IRFPA) sensors, due to
their high sensitivity, high frame frequency and simple structure, have
become the most prominently used detectors in military applications.
However, they suffer from a common problem called the fixed pattern
noise (FPN), which severely degrades image quality and limits the
infrared imaging applications. Therefore, it is necessary to perform
non-uniformity correction (NUC) on IR image. The algorithms of
non-uniformity correction are classified into two main categories, the
calibration-based and scene-based algorithms. There exist some
shortcomings in both algorithms, hence a novel non-uniformity
correction algorithm based on non-linear fit is proposed, which
combines the advantages of the two algorithms. Experimental results
show that the proposed algorithm acquires a good effect of NUC with
a lower non-uniformity ratio.