Abstract: Power system stability enhancement by simultaneous tuning of a Power System Stabilizer (PSS) and a Static Var Compensator (SVC)-based controller is thoroughly investigated in this paper. The coordination among the proposed damping stabilizers and the SVC internal voltage regulators has also been taken into consideration. The design problem is formulated as an optimization problem with a time-domain simulation-based objective function and Real-Coded Genetic Algorithm (RCGA) is employed to search for optimal controller parameters. The proposed stabilizers are tested on a weakly connected power system with different disturbances and loading conditions. The nonlinear simulation results are presented to show the effectiveness and robustness of the proposed control schemes over a wide range of loading conditions and disturbances. Further, the proposed design approach is found to be robust and improves stability effectively even under small disturbance and unbalanced fault conditions.
Abstract: Bleeding in the digestive duct is an important diagnostic parameter for patients. Blood in the endoscopic image can be determined by investigating the color tone of blood due to the degree of oxygenation, under- or over- illumination, food debris and secretions, etc. However, we found that how to pre-process raw images obtained from the capsule detectors was very important. We applied various image process methods suitable for the capsule endoscopic image in order to remove noises and unbalanced sensitivities for the image pixels. The results showed that much improvement was achieved by additional pre-processing techniques on the algorithm of determining bleeding areas.
Abstract: In this paper, we propose the Modified Synchronous Detection (MSD) Method for determining the reference compensating currents of the shunt active power filter under non sinusoidal voltages conditions. For controlling the inverter switching we used the PI regulator. The numerical simulation results, using Power System Blockset Toolbox PSB of Matlab, from a complete structure, are presented and discussed.
Abstract: In recent years the large scale use of the power electronic equipment has led to an increase of harmonics in the power system. The harmonics results into a poor power quality and have great adverse economical impact on the utilities and customers. Current harmonics are one of the most common power quality problems and are usually resolved by using shunt active filter (SHAF). The main objective of this work is to develop PI and Fuzzy logic controllers (FLC) to analyze the performance of Shunt Active Filter for mitigating current harmonics under balanced and unbalanced sinusoidal source voltage conditions for normal load and increased load. When the supply voltages are ideal (balanced), both PI and FLC are converging to the same compensation characteristics. However, the supply voltages are non-ideal (unbalanced), FLC offers outstanding results. Simulation results validate the superiority of FLC with triangular membership function over the PI controller.
Abstract: Sensory input plays an important role to human
posture control system to initiate strategy in order to counterpart any
unbalance condition and thus, prevent fall. In previous study, joint
stiffness was observed able to describe certain issues regarding to
movement performance. But, correlation between balance ability and
joint stiffness is still remains unknown. In this study, joint stiffening
strategy at ankle and hip were observed under different sensory
manipulations and its correlation with conventional clinical test
(Functional Reach Test) for balance ability was investigated. In order
to create unstable condition, two different surface perturbations (tilt
up-tilt (TT) down and forward-backward (FB)) at four different
frequencies (0.2, 0.4, 0.6 and 0.8 Hz) were introduced. Furthermore,
four different sensory manipulation conditions (include vision and
vestibular system) were applied to the subject and they were asked to
maintain their position as possible. The results suggested that joint
stiffness were high during difficult balance situation. Less balance
people generated high average joint stiffness compared to balance
people. Besides, adaptation of posture control system under repetitive
external perturbation also suggested less during sensory limited
condition. Overall, analysis of joint stiffening response possible to
predict unbalance situation faced by human
Abstract: In order to make environmental test centrifuge balance
automatically and accurately, reduce unbalance centrifugal force,
balance adjusting system of centrifuge is designed. The new balance
adjusting system comprises motor-reducer, timing belt, screw pair,
slider-guideway and four rocker force sensors. According to
information obtained by the four rocker force sensors, unbalanced
value at both ends of the big arm is computed and heavy block is
moved to achieve balance adjusting. In this paper, motor power and
torque to move the heavy block is calculated. In full load running
progress of centrifuge, the stress-strain of screw pair composed by
adjusting nut and big arm are analyzed. A successful application of the
balance adjusting system is also put forwarded. The results show that
the balance adjusting system can satisfy balance require of
environmental test centrifuge.
Abstract: In this paper the behavior of fixed series compensated
extra high voltage transmission lines during faults is simulated. Many
over-voltage protection schemes for series capacitors are limited in
terms of size and performance, and are easily affected by
environmental conditions. While the need for more compact and
environmentally robust equipment is required. use of series
capacitors for compensating part of the inductive reactance of long
transmission lines increases the power transmission capacity.
Emphasis is given on the impact of modern capacitor protection
techniques (MOV protection). The simulation study is performed
using MATLAB/SIMULINK®and results are given for a three phase
and a single phase to ground fault.
Abstract: In this paper a three dimensional thermal model of
high breaking capacity fuse with unequal fuse links is proposed for
both steady-state or transient conditions. The influence of ambient
temperature and electric current on the temperature distribution
inside the fuse, has been investigated. A thermal analysis of the
unbalanced distribution of the electric current through the fuse
elements and their influence on fuse link temperature rise, has been
performed. To validate the three dimensional thermal model, some
experimental tests have been done. There is a good correlation
between experimental and simulation results.
Abstract: Because of architectural condition and structure application, sometimes mass source and stiffness source are not coincidence, and the structure is irregular. The structure is also might be asymmetric as an asymmetric bracing in plan which leads to unbalance distribution of stiffness or because of unbalance distribution of the mass. Both condition lead to eccentricity and torsion in the structure. The deficiency of ordinary code to evaluate the performance of steel structures against earthquake has been caused designing based on performance level or capacity spectrum be used. By using the mentioned methods it is possible to design a structure that its behavior against different earthquakes be predictive. In this article 5- story buildings with different percentage of asymmetric which is because of stiffness changes have been designed. The static and dynamic nonlinear analysis under three acceleration recording has been done. Finally performance level of the structure has been evaluated.
Abstract: To maximise furnace production it-s necessary to
optimise furnace control, with the objectives of achieving maximum
power input into the melting process, minimum network distortion
and power-off time, without compromise on quality and safety. This
can be achieved with on the one hand by an appropriate electrode
control and on the other hand by a minimum of AC transformer
switching.
Electrical arc is a stochastic process; witch is the principal cause
of power quality problems, including voltages dips, harmonic
distortion, unbalance loads and flicker. So it is difficult to make an
appropriate model for an Electrical Arc Furnace (EAF). The factors
that effect EAF operation are the melting or refining materials,
melting stage, electrode position (arc length), electrode arm control
and short circuit power of the feeder. So arc voltages, current and
power are defined as a nonlinear function of the arc length. In this
article we propose our own empirical function of the EAF and model,
for the mean stages of the melting process, thanks to the
measurements in the steel factory.
Abstract: This paper attempts to identify the significance of
Information and Communications Technology (ICT) and
competitiveness to the profit efficiency of commercial banks in
Malaysia. The profit efficiency of commercial banks in Malaysia, the
dependent variable, was estimated using the Stochastic Frontier
Approach (SFA) on a sample of unbalanced panel data, covering 23
commercial banks, between 1995 to 2007. Based on the empirical
results, ICT was not found to exert a significant impact on profit
efficiency, whereas competitiveness, non ICT stock expenditure and
ownership were significant contributors. On the other hand, the size
of banks was found to have significantly reduced profit efficiency,
opening up for various interpretations of the interrelated role of ICT
and competition.
Abstract: In this paper, genetic algorithm (GA) opmization technique is applied to design Flexible AC Transmission System (FACTS)-based damping controllers. Two types of controller structures, namely a proportional-integral (PI) and a lead-lag (LL) are considered. The design problem of the proposed controllers is formulated as an optimization problem and GA is employed to search for optimal controller parameters. By minimizing the time-domain based objective function, in which the deviation in the oscillatory rotor speed of the generator is involved; stability performance of the system is improved. The proposed controllers are tested on a weakly connected power system subjected to different disturbances. The non-linear simulation results are presented to show the effectiveness of the proposed controller and their ability to provide efficient damping of low frequency oscillations. It is also observed that the proposed SSSC-based controllers improve greatly the voltage profile of the system under severe disturbances. Further, the dynamic performances of both the PI and LL structured FACTS-controller are analyzed at different loading conditions and under various disturbance condition as well as under unbalanced fault conditions..
Abstract: This paper presents modeling and optimization of two NP-hard problems in flexible manufacturing system (FMS), part type selection problem and loading problem. Due to the complexity and extent of the problems, the paper was split into two parts. The first part of the papers has discussed the modeling of the problems and showed how the real coded genetic algorithms (RCGA) can be applied to solve the problems. This second part discusses the effectiveness of the RCGA which uses an array of real numbers as chromosome representation. The novel proposed chromosome representation produces only feasible solutions which minimize a computational time needed by GA to push its population toward feasible search space or repair infeasible chromosomes. The proposed RCGA improves the FMS performance by considering two objectives, maximizing system throughput and maintaining the balance of the system (minimizing system unbalance). The resulted objective values are compared to the optimum values produced by branch-and-bound method. The experiments show that the proposed RCGA could reach near optimum solutions in a reasonable amount of time.
Abstract: In this paper, a particle swarm optimization (PSO)
algorithm is proposed to solve machine loading problem in flexible
manufacturing system (FMS), with bicriterion objectives of
minimizing system unbalance and maximizing system throughput in
the occurrence of technological constraints such as available
machining time and tool slots. A mathematical model is used to
select machines, assign operations and the required tools. The
performance of the PSO is tested by using 10 sample dataset and the
results are compared with the heuristics reported in the literature. The
results support that the proposed PSO is comparable with the
algorithms reported in the literature.
Abstract: This paper presents a fast and efficient on-line technique for estimating impedance of unbalanced loads in power systems. The proposed technique is an application of a discrete timedynamic filter based on stochastic estimation theory which is suitable for estimating parameters in noisy environment. The algorithm uses sets of digital samples of the distorted voltage and current waveforms of the non-linear load to estimate the harmonic contents of these two signal. The non-linear load impedance is then calculated from these contents. The method is tested using practical data. Results are reported and compared with those obtained using the conventional least error squares technique. In addition to the very accurate results obtained, the method can detect and reject bad measurements. This can be considered as a very important advantage over the conventional static estimation methods such as the least error square method.
Abstract: This research is a comparative study of complexity, as a multidimensional concept, in the context of streetscape composition in Algeria and Japan. 80 streetscapes visual arrays have been collected and then presented to 20 participants, with different cultural backgrounds, in order to be categorized and classified according to their degrees of complexity. Three analysis methods have been used in this research: cluster analysis, ranking method and Hayashi Quantification method (Method III). The results showed that complexity, disorder, irregularity and disorganization are often conflicting concepts in the urban context. Algerian daytime streetscapes seem to be balanced, ordered and regular, and Japanese daytime streetscapes seem to be unbalanced, regular and vivid. Variety, richness and irregularity with some aspects of order and organization seem to characterize Algerian night streetscapes. Japanese night streetscapes seem to be more related to balance, regularity, order and organization with some aspects of confusion and ambiguity. Complexity characterized mainly Algerian avenues with green infrastructure. Therefore, for Japanese participants, Japanese traditional night streetscapes were complex. And for foreigners, Algerian and Japanese avenues nightscapes were the most complex visual arrays.