Abstract: This paper proposes a feed-forward control in a halfbridge
resonant dc link inverter. The configuration of feed-forward
control is based on synchronous sigma-delta modulation and the halfbridge
resonant dc link inverter consists of two inductors, one
capacitor and two power switches. The simulation results show the
proposed technique can reject non-ideal dc bus improving the total
harmonic distortion.
Abstract: In this paper we present a generic approach for the problem of the blind estimation of the parameters of linear and convolutional error correcting codes. In a non-cooperative context, an adversary has only access to the noised transmission he has intercepted. The intercepter has no knowledge about the parameters used by the legal users. So, before having acess to the information he has first to blindly estimate the parameters of the error correcting code of the communication. The presented approach has the main advantage that the problem of reconstruction of such codes can be expressed in a very simple way. This allows us to evaluate theorical bounds on the complexity of the reconstruction process but also bounds on the estimation rate. We show that some classical reconstruction techniques are optimal and also explain why some of them have theorical complexities greater than these experimentally observed.
Abstract: In this paper an attempt has been made to correlate the usefulness of electrodes made through powder metallurgy (PM) in comparison with conventional copper electrode during electric discharge machining. Experimental results are presented on electric discharge machining of AISI D2 steel in kerosene with copper tungsten (30% Cu and 70% W) tool electrode made through powder metallurgy (PM) technique and Cu electrode. An L18 (21 37) orthogonal array of Taguchi methodology was used to identify the effect of process input factors (viz. current, duty cycle and flushing pressure) on the output factors {viz. material removal rate (MRR) and surface roughness (SR)}. It was found that CuW electrode (made through PM) gives high surface finish where as the Cu electrode is better for higher material removal rate.
Abstract: In the last few years, three multivariate spectral
analysis techniques namely, Principal Component Analysis (PCA),
Independent Component Analysis (ICA) and Non-negative Matrix
Factorization (NMF) have emerged as effective tools for oscillation
detection and isolation. While the first method is used in determining
the number of oscillatory sources, the latter two methods
are used to identify source signatures by formulating the detection
problem as a source identification problem in the spectral domain.
In this paper, we present a critical drawback of the underlying linear
(mixing) model which strongly limits the ability of the associated
source separation methods to determine the number of sources
and/or identify the physical source signatures. It is shown that the
assumed mixing model is only valid if each unit of the process gives
equal weighting (all-pass filter) to all oscillatory components in its
inputs. This is in contrast to the fact that each unit, in general, acts
as a filter with non-uniform frequency response. Thus, the model
can only facilitate correct identification of a source with a single
frequency component, which is again unrealistic. To overcome
this deficiency, an iterative post-processing algorithm that correctly
identifies the physical source(s) is developed. An additional issue
with the existing methods is that they lack a procedure to pre-screen
non-oscillatory/noisy measurements which obscure the identification
of oscillatory sources. In this regard, a pre-screening procedure
is prescribed based on the notion of sparseness index to eliminate
the noisy and non-oscillatory measurements from the data set used
for analysis.
Abstract: Knowing the geometrical object pose of products in manufacturing line before robot manipulation is required and less time consuming for overall shape measurement. In order to perform it, the information of shape representation and matching of objects is become required. Objects are compared with its descriptor that conceptually subtracted from each other to form scalar metric. When the metric value is smaller, the object is considered closed to each other. Rotating the object from static pose in some direction introduce the change of value in scalar metric value of boundary information after feature extraction of related object. In this paper, a proposal method for indexing technique for retrieval of 3D geometrical models based on similarity between boundaries shapes in order to measure 3D CAD object pose using object shape feature matching for Computer Aided Testing (CAT) system in production line is proposed. In experimental results shows the effectiveness of proposed method.
Abstract: In this paper, hybrid FDMA-TDMA access technique in a cooperative distributive fashion introducing and implementing a modified protocol introduced in [1] is analyzed termed as Power and Cooperation Diversity Gain Protocol (PCDGP). A wireless network consists of two users terminal , two relays and a destination terminal equipped with two antennas. The relays are operating in amplify-and-forward (AF) mode with a fixed gain. Two operating modes: cooperation-gain mode and powergain mode are exploited from source terminals to relays, as it is working in a best channel selection scheme. Vertical BLAST (Bell Laboratories Layered Space Time) or V-BLAST with minimum mean square error (MMSE) nulling is used at the relays to perfectly detect the joint signals from multiple source terminals. The performance is analyzed using binary phase shift keying (BPSK) modulation scheme and investigated over independent and identical (i.i.d) Rayleigh, Ricean-K and Nakagami-m fading environments. Subsequently, simulation results show that the proposed scheme can provide better signal quality of uplink users in a cooperative communication system using hybrid FDMATDMA technique.
Abstract: Selection of a project among a set of possible
alternatives is a difficult task that the decision maker (DM) has to
face. In this paper, by using a fuzzy TOPSIS technique we propose a
new method for a project selection problem. After reviewing four
common methods of comparing investment alternatives (net present
value, rate of return, benefit cost analysis and payback period) we
use them as criteria in a TOPSIS technique. First we calculate the
weight of each criterion by a pairwise comparison and then we utilize
the improved TOPSIS assessment for the project selection.
Abstract: Fast delay estimation methods, as opposed to
simulation techniques, are needed for incremental performance
driven layout synthesis. On-chip inductive effects are becoming
predominant in deep submicron interconnects due to increasing clock
speed and circuit complexity. Inductance causes noise in signal
waveforms, which can adversely affect the performance of the circuit
and signal integrity. Several approaches have been put forward which
consider the inductance for on-chip interconnect modelling. But for
even much higher frequency, of the order of few GHz, the shunt
dielectric lossy component has become comparable to that of other
electrical parameters for high speed VLSI design. In order to cope up
with this effect, on-chip interconnect has to be modelled as
distributed RLCG line. Elmore delay based methods, although
efficient, cannot accurately estimate the delay for RLCG interconnect
line. In this paper, an accurate analytical delay model has been
derived, based on first and second moments of RLCG
interconnection lines. The proposed model considers both the effect
of inductance and conductance matrices. We have performed the
simulation in 0.18μm technology node and an error of as low as less
as 5% has been achieved with the proposed model when compared to
SPICE. The importance of the conductance matrices in interconnect
modelling has also been discussed and it is shown that if G is
neglected for interconnect line modelling, then it will result an delay
error of as high as 6% when compared to SPICE.
Abstract: In the past decade, because of wide applications of
hybrid systems, many researchers have considered modeling and
control of these systems. Since switching systems constitute an
important class of hybrid systems, in this paper a method for optimal
control of linear switching systems is described. The method is also
applied on the two-tank system which is a much appropriate system
to analyze different modeling and control techniques of hybrid
systems. Simulation results show that, in this method, the goals of
control and also problem constraints can be satisfied by an
appropriate selection of cost function.
Abstract: The complexity of teaching English in higher
institutions by non-native speakers within a second/foreign language
setting has created continuous discussions and research about
teaching approaches and teaching practises, professional identities
and challenges. In addition, there is a growing awareness that
teaching English within discipline-specific contexts adds up to the
existing complexity. This awareness leads to reassessments,
discussions and suggestions on course design and content and
teaching approaches and techniques. In meeting expectations
teaching at a university specified in a particular discipline such as
engineering, English language educators are not only required to
teach students to be able to communicate in English effectively but
also to teach soft skills such as problem solving skills. This paper is
part of a research conducted to investigate how English language
educators negotiate with the complexities of teaching problem
solving skills through English language teaching at a technical
university. This paper reports the way an English language educator
identified himself and the way he approached his teaching in this
institutional context.
Abstract: This paper investigates the inverse problem of determining
the unknown time-dependent leading coefficient in the parabolic
equation using the usual conditions of the direct problem and an additional
condition. An algorithm is developed for solving numerically
the inverse problem using the technique of space decomposition in a
reproducing kernel space. The leading coefficients can be solved by a
lower triangular linear system. Numerical experiments are presented
to show the efficiency of the proposed methods.
Abstract: In this study a clustering technique has been implemented which is K-Means like with hierarchical initial set (HKM). The goal of this study is to prove that clustering document sets do enhancement precision on information retrieval systems, since it was proved by Bellot & El-Beze on French language. A comparison is made between the traditional information retrieval system and the clustered one. Also the effect of increasing number of clusters on precision is studied. The indexing technique is Term Frequency * Inverse Document Frequency (TF * IDF). It has been found that the effect of Hierarchical K-Means Like clustering (HKM) with 3 clusters over 242 Arabic abstract documents from the Saudi Arabian National Computer Conference has significant results compared with traditional information retrieval system without clustering. Additionally it has been found that it is not necessary to increase the number of clusters to improve precision more.