Abstract: We present the development of a new underwater laser
cutting process in which a water-jet has been used along with the
laser beam to remove the molten material through kerf. The
conventional underwater laser cutting usually utilizes a high pressure
gas jet along with laser beam to create a dry condition in the cutting
zone and also to eject out the molten material. This causes a lot of gas
bubbles and turbulence in water, and produces aerosols and waste
gas. This may cause contamination in the surrounding atmosphere
while cutting radioactive components like burnt nuclear fuel. The
water-jet assisted underwater laser cutting process produces much
less turbulence and aerosols in the atmosphere. Some amount of
water vapor bubbles is formed at the laser-metal-water interface;
however, they tend to condense as they rise up through the
surrounding water. We present the design and development of a
water-jet assisted underwater laser cutting head and the parametric
study of the cutting of AISI 304 stainless steel sheets with a 2 kW
CW fiber laser. The cutting performance is similar to that of the gas
assist laser cutting; however, the process efficiency is reduced due to
heat convection by water-jet and laser beam scattering by vapor. This
process may be attractive for underwater cutting of nuclear reactor
components.
Abstract: A general stochastic spatial MIMO channel model is
proposed for evaluating various MIMO techniques in this paper. It can
generate MIMO channels complying with various MIMO
configurations such as smart antenna, spatial diversity and spatial
multiplexing. The modeling method produces the stochastic fading
involving delay spread, Doppler spread, DOA (direction of arrival),
AS (angle spread), PAS (power azimuth Spectrum) of the scatterers,
antenna spacing and the wavelength. It can be applied in various
MIMO technique researches flexibly with low computing complexity.
Abstract: The spiral angle of the elementary cellulose fibril in
the wood cell wall, often called microfibril angle, (MFA). Microfibril
angle in hardwood is one of the key determinants of solid timber
performance due to its strong influence on the stiffness, strength,
shrinkage, swelling, thermal-dynamics mechanical properties and
dimensional stability of wood. Variation of MFA (degree) in the S2
layer of the cell walls among Acacia mangium trees was determined
using small-angle X-ray scattering (SAXS). The length and
orientation of the microfibrils of the cell walls in the irradiated
volume of the thin samples are measured using SAXS and optical
microscope for 3D surface measurement. The undetermined
parameters in the analysis are the MFA, (M) and the standard
deviation (σФ) of the intensity distribution arising from the wandering
of the fibril orientation about the mean value. Nine separate pairs of
values are determined for nine different values of the angle of the
incidence of the X-ray beam relative to the normal to the radial
direction in the sample. The results show good agreement. The
curve distribution of scattered intensity for the real cell wall structure
is compared with that calculated with that assembly of rectangular
cells with the same ratio of transverse to radial cell wall length. It is
demonstrated that for β = 45°, the peaks in the curve intensity
distribution for the real and the rectangular cells coincide. If this
peak position is Ф45, then the MFA can be determined from the
relation M = tan-1 (tan Ф45 / cos 45°), which is precise for rectangular
cells. It was found that 92.93% of the variation of MFA can be
attributed to the distance from pith to bark. Here we shall present our
results of the MFA in the cell wall with respect to its shape, structure
and the distance from pith to park as an important fast check and yet
accurate towards the quality of wood, its uses and application.
Abstract: Managing knowledge of research is one way to ensure
just in time information and knowledge to support research strategist
and activities. Unfortunately researcher found the vital research
knowledge in IHL (Institutions of Higher Learning) are scattered,
unstructured and unorganized. Aiming on lay aside conceptual
foundations for understanding and developing OMS (Organizational
Memory System) to facilitate research in IHL, this research revealed
ten factors contributed to the needs of research in the IHL and seven
internal challenges of IHL in promoting research to their academic
members. This study then suggested a comprehensive support of
managing research knowledge using Organizational Memory System
(OMS). Eight OMS characteristics to support research were
identified. Finally the initial work in designing OMS was projected
using knowledge taxonomy. All analysis is derived from pertinent
research paper related to research in IHL and OMS. Further study can
be conducted to validate and verify results presented.
Abstract: In the context of global climate change, flooding and sea level rise is increasingly threatening coastal urban areas, in which large population is continuously concentrated. Dutch experiences in urban water system management provide high reference value for sustainable coastal urban development projects. Preliminary studies shows the urban water system in Almere, a typical Dutch polder city, have three kinds of operational modes, achieving functions as: (1) coastline control – strong multiple damming system prevents from storm surges and maintains sufficient capacity upon risks; (2) high flexibility – large area and widely scattered open water system greatly reduce local runoff and water level fluctuation; (3) internal water maintenance – weir and sluice system maintains relatively stable water level, providing excellent boating and landscaping service, coupling with water circulating model maintaining better water quality. Almere has provided plenty of hints and experiences for ongoing development of coastal cities in emerging economies.
Abstract: In this study spatial-temporal speckle correlation techniques have been applied for the quality evaluation of three different Indian fruits namely apple, pear and tomato for the first time. The method is based on the analysis of variations of laser light scattered from biological samples. The results showed that crosscorrelation coefficients of biospeckle patterns change subject to their freshness and the storage conditions. The biospeckle activity was determined by means of the cross-correlation functions of the intensity fluctuations. Significant changes in biospeckle activity were observed during their shelf lives. From the study, it is found that the biospeckle activity decreases with the shelf-life storage time. Further it has been shown that biospeckle activity changes according to their respiration rates.
Abstract: The morphological parameter of a thin film surface
can be characterized by power spectral density (PSD) functions
which provides a better description to the topography than the RMS
roughness and imparts several useful information of the surface
including fractal and superstructure contributions. Through the
present study Nanoparticle copper/carbon composite films were
prepared by co-deposition of RF-Sputtering and RF-PECVD method
from acetylene gas and copper target. Surface morphology of thin
films is characterized by using atomic force microscopy (AFM). The
Carbon content of our films was obtained by Rutherford Back
Scattering (RBS) and it varied from .4% to 78%. The power values of
power spectral density (PSD) for the AFM data were determined by
the fast Fourier transform (FFT) algorithms. We investigate the effect
of carbon on the roughness of thin films surface. Using such
information, roughness contributions of the surface have been
successfully extracted.