Abstract: One of the aspects that are usually neglected during the design phase of an engine is the effect of the spark plug on the flow field inside the combustion chamber. Because of the difficulties in the experimental investigation of the mutual interaction between flow alteration and early flame kernel convection effect inside the engine combustion chamber, CFD-3D simulation is usually exploited in such cases. Experimentally speaking, a particular type of engine has to be used in order to directly observe the flame propagation process. In this study, a double electrode spark plug was fitted into an optically accessible engine and a high-speed camera was used to capture the initial stages of the combustion process. Both the arc and the kernel phases were observed. Then, a morphologic analysis was carried out and the position of the center of mass of the flame, relative to the spark plug position, was calculated. The crossflow orientation was chosen for the spark plug and the kernel growth process was observed for different air-fuel ratios. It was observed that during a normal cycle the flow field between the electrodes tends to transport the arc deforming it. Because of that, the kernel growth phase takes place away from the electrodes and the flame propagates with a preferential direction dictated by the flow field.
Abstract: This experimental investigation aimed to determine the influence of using different types of alcohol and gasoline blends such as ethanol - butanol - propanol on the performance of spark ignition engine. The experimental work studied the effect of various fuel blends such as ethanol – butanol/gasoline and propanol/gasoline with two rates of 15% and 20%, at different operating conditions (engine speed and loads), on engine performance emission characteristics. Laboratory experiments are carried out on a four-cylinder spark ignition (SI) engine. In this practical study, all considerations and precautions are taken into account to ensure the quality and accuracy of practical experiments and different measurements. The results show that the performance of the engine improved significantly in the case of ethanol/butanol-gasoline blends. The results also indicated that the engine emitted pollutants such as CO, hydrocarbon (HC) for alcohol fuel blends compared to base gasoline NOx emission increased for different fuel blends either ethanol/butanol-gasoline or propanol-gasoline fuel blend.
Abstract: Crank shaft length, connecting rod length, crank angle, engine rpm, cylinder bore, mass of piston and compression ratio are the inputs that can control the performance of the slider crank mechanism and then its efficiency. Several combinations of these seven inputs are used and compared. The throughput engine torque predicted by the simulation is analyzed through two different regression models, with and without interaction terms, developed according to multi-linear regression using LU decomposition to solve system of algebraic equations. These models are validated. A regression model in seven inputs including their interaction terms lowered the polynomial degree from 3rd degree to 1st degree and suggested valid predictions and stable explanations.
Abstract: In this paper, the performance and emission characteristics of a Single Cylinder Spark Ignition engine have been investigated. The research is based on micro emulsion application as fuel in a gasoline engine. We have analyzed many micro emulsion compositions in various proportions, for predicting the performance of the Spark Ignition engine. This new technology of fuel modifications is emerging very rapidly as lot of research is going on in the field of micro emulsion fuels in Compression Ignition engines, but the micro emulsion fuel used in a Gasoline engine is very rare. The use of micro emulsion as fuel in a Spark Ignition engine is virtually unexplored. So, our main goal is to see the performance and emission characteristics of micro emulsions as fuel, in Spark Ignition engines, and finding which composition is more efficient. In this research, we have used various micro emulsion fuels whose composition varies for all the three blends, and their performance and emission characteristic were predicted in AVL Boost software. Conventional Gasoline fuel 90%, 80% and 85% were blended with co-surfactant Ethanol in different compositions, and water was used as an additive for making it crystal clear transparent micro emulsion fuel, which is thermodynamically stable. By comparing the performances of engines, the power has shown similarity for micro emulsion fuel and conventional Gasoline fuel. On the other hand, Torque and BMEP shows increase for all the micro emulsion fuels. Micro emulsion fuel shows higher thermal efficiency and lower Specific Fuel Consumption for all the compositions as compared to the Gasoline fuel. Carbon monoxide and Hydro carbon emissions were also measured. The result shows that emissions decrease for all the composition of micro emulsion fuels, and proved to be the most efficient fuel both in terms of performance and emission characteristics.
Abstract: The in-cylinder flow and mixture formations are
significant in view of today’s increasing concern on environmental
issues and stringent emission regulations. In this paper, the numerical
simulations of a SI engine at different engine speeds (2000-5000
rpm) at fixed intake flow pressure of 1 bar are studied using the AVL
FIRE software. The simulation results show that when the engine
speed at fixed intake flow pressure is increased, the volumetric
efficiency of the engine decreases. This is due to a richer fuel
conditions near the engine cylinder wall when engine speed is
increased. Significant effects of impingement are also noted on the
upper and side walls of the engine cylinder. These variations in
mixture formation before ignition could affect the thermodynamics
efficiency and specific fuel consumption that would lead to a reduced
engine performance.
Abstract: The intension in this work is to investigate the effect of different fuels type on engine performance for different engine speed. Brake Power, Brake Torque, and specific fuel consumption were calculated and presented to show the effect of varying fuel type on them for all cases considered. A special program used to carry out the calculations. A simulation model for one-cylinder spark ignition engine has been built and calculated.
The analysis of the results shows that for methanol the power increases about 30% at 1000 rpm and 16% at 6000 rpm comparing with methane. For the same compared fuels the increment in fuel consumption is about 100% at 1000 rpm and 115% at 6000 rpm. The increment in brake thermal efficiency for gasoline is around 11% comparing with methane at 1000 rpm and 7% for methanol comparing with methane at 4000 rpm.
Abstract: the intension in this work is to investigate the effect of
different bending manifold pipes on engine performance for different
engine speed. Power, Torque, and BSFC were calculated and
presented to show the effect of varying bending pipes angles on them
for all cases considered. A special program used to carry out the
calculations. A simulation model for 4-cylinders spark ignition
engine with turbocharger has been built and calculated. The analysis
of the results shows that for 120o angle the torque increases about
40% at 3000 rpm and 25% at 4000 rpm without changing in fuel
consumption. For 90o angle the increment in torque is about 10 %.
For the same bending angle the increment in brake power is around
40% at 3000 rpm and 25% at 4000 rpm. The increment in fuel
consumption is about 12% for 60o and 30% for 90o between (6000-
7000) rpm.
Abstract: In order to meet the limits imposed on automotive
emissions, engine control systems are required to constrain air/fuel
ratio (AFR) in a narrow band around the stoichiometric value, due to
the strong decay of catalyst efficiency in case of rich or lean mixture.
This paper presents a model of a sample spark ignition engine and
demonstrates Simulink-s capabilities to model an internal combustion
engine from the throttle to the crankshaft output. We used welldefined
physical principles supplemented, where appropriate, with
empirical relationships that describe the system-s dynamic behavior
without introducing unnecessary complexity. We also presents a PID
tuning method that uses an adaptive fuzzy system to model the
relationship between the controller gains and the target output
response, with the response specification set by desired percent
overshoot and settling time. The adaptive fuzzy based input-output
model is then used to tune on-line the PID gains for different
response specifications. Experimental results demonstrate that better
performance can be achieved with adaptive fuzzy tuning relative to
similar alternative control strategies. The actual response
specifications with adaptive fuzzy matched the desired response
specifications.