Abstract: Sputtered CoxCu100-x films with the different compositions of x = 57.7, 45.8, 25.5, 13.8, 8.8, 7.5 and 1.8 were deposited on Cr under-layer by RF-sputtering. SEM result reveals that the averaged thickness of Co-Cu film and Cr under-layer are 92 nm and 22nm, respectively. All Co-Cu films are composed of Co (FCC) and Cu (FCC) phases in (111) directions on BCC-Cr (110) under-layers. Magnetic properties, surface roughness and morphology of Co-Cu films are dependent on the film composition. The maximum and minimum surface roughness of 3.24 and 1.16nm are observed on the Co7.5Cu92.5 and Co45.8Cu54.2films, respectively. It can be described that the variance of surface roughness of the film because of the difference of the agglomeration rate of Co and Cu atoms on Cr under-layer. The Co57.5Cu42.3, Co45.8Cu54.2 and Co25.5Cu74.5 films shows the ferromagnetic phase whereas the rest of the film exhibits the paramagnetic phase at room temperature. The saturation magnetization, remnant magnetization and coercive field of Co-Cu films on Cr under-layer are slightly increased with increasing the Co composition. It can be concluded that the required magnetic properties and surface roughness of the Co-Cu film can be adapted by the adjustment of the film composition.
Abstract: In this study, artificial limestone brick samples are produced by using wood sawdust wastes (WSW) having different grades of sizes and limestone powder waste (LPW). The thermo-elastic properties of produced brick samples in various WSW amounts are investigated. At 30% WSW replacement with LPW in the brick sample the thermal conductivity value is effectively reduced and the reduction in the thermal conductivity value of brick sample at 30% WSW replacement with LPW is about 38.9% as compared with control sample. The energy conservation in buildings by using LPW and WSW in masonry brick material production having low thermal conductivity reduces energy requirements. A strong relationship is also found among the thermal conductivity, unit weight and ultrasonic pulse velocity values of brick samples produced. It shows a potential to be used for walls, wooden board substitute, alternative to the concrete blocks, ceiling panels, sound barrier panels, absorption materials etc.
Abstract: Signature amortization schemes have been introduced
for authenticating multicast streams, in which, a single signature is
amortized over several packets. The hash value of each packet is
computed, some hash values are appended to other packets, forming
what is known as hash chain. These schemes divide the stream into
blocks, each block is a number of packets, the signature packet in
these schemes is either the first or the last packet of the block.
Amortization schemes are efficient solutions in terms of computation
and communication overhead, specially in real-time environment.
The main effictive factor of amortization schemes is it-s hash chain
construction. Some studies show that signing the first packet of each
block reduces the receiver-s delay and prevents DoS attacks, other
studies show that signing the last packet reduces the sender-s delay.
To our knowledge, there is no studies that show which is better, to
sign the first or the last packet in terms of authentication probability
and resistance to packet loss.
In th is paper we will introduce another scheme for authenticating
multicast streams that is robust against packet loss, reduces the
overhead, and prevents the DoS attacks experienced by the receiver
in the same time. Our scheme-The Multiple Connected Chain signing
the First packet (MCF) is to append the hash values of specific
packets to other packets,then append some hashes to the signature
packet which is sent as the first packet in the block. This scheme
is aspecially efficient in terms of receiver-s delay. We discuss and
evaluate the performance of our proposed scheme against those that
sign the last packet of the block.
Abstract: In this paper, we investigated the characteristic of a
clinical dataseton the feature selection and classification
measurements which deal with missing values problem.And also
posed the appropriated techniques to achieve the aim of the activity;
in this research aims to find features that have high effect to mortality
and mortality time frame. We quantify the complexity of a clinical
dataset. According to the complexity of the dataset, we proposed the
data mining processto cope their complexity; missing values, high
dimensionality, and the prediction problem by using the methods of
missing value replacement, feature selection, and classification.The
experimental results will extend to develop the prediction model for
cardiology.
Abstract: We present a preliminary x-ray study on human-hair
microstructures for a health-state indicator, in particular a cancer
case. As an uncomplicated and low-cost method of x-ray technique,
the human-hair microstructure was analyzed by wide-angle x-ray
diffractions (XRD) and small-angle x-ray scattering (SAXS). The
XRD measurements exhibited the simply reflections at the d-spacing
of 28 Å, 9.4 Å and 4.4 Å representing to the periodic distance of the
protein matrix of the human-hair macrofibrous and the diameter and
the repeated spacing of the polypeptide alpha helixes of the
photofibrils of the human-hair microfibrous, respectively. When
compared to the normal cases, the unhealthy cases including to the
breast- and ovarian-cancer cases obtained higher normalized ratios of
the x-ray diffracting peaks of 9.4 Å and 4.4 Å. This likely resulted
from the varied distributions of microstructures by a molecular
alteration. As an elemental analysis by x-ray fluorescence (XRF), the
normalized quantitative ratios of zinc(Zn)/calcium(Ca) and
iron(Fe)/calcium(Ca) were determined. Analogously, both Zn/Ca and
Fe/Ca ratios of the unhealthy cases were obtained higher than both of
the normal cases were. Combining the structural analysis by XRD
measurements and the elemental analysis by XRF measurements
exhibited that the modified fibrous microstructures of hair samples
were in relation to their altered elemental compositions. Therefore,
these microstructural and elemental analyses of hair samples will be
benefit to associate with a diagnosis of cancer and genetic diseases.
This functional method would lower a risk of such diseases by the
early diagnosis. However, the high-intensity x-ray source, the highresolution
x-ray detector, and more hair samples are necessarily
desired to develop this x-ray technique and the efficiency would be
enhanced by including the skin and fingernail samples with the
human-hair analysis.
Abstract: This paper proposes a model of adding relations between
members of the same level in a pyramid organization structure
which is a complete K-ary tree such that the communication of
information between every member in the organization becomes the
most efficient. When edges between one node and every other node
with the same depth N in a complete K-ary tree of height H are
added, an optimal depth N* = H is obtained by minimizing the total
path length which is the sum of lengths of shortest paths between
every pair of all nodes.
Abstract: Addition of an oily waste to a co-composting process of dairy cow manure with food waste, and the influence in the final product was evaluated. Three static composting piles with different substrates concentrations were assessed. Sawdust was also added to all composting piles to attain 60%, humidity at the beginning of the process. In pile 1, the co-substrates were the solid-phase of dairy cow manure, food waste and sawdust as bulking agent. In piles 2 and 3 there was an extra input of oily waste of 7 and 11% of the total volume, respectively, corresponding to 18 and 28% in dry weight. The results showed that the co-composting process was feasible even at the highest fat content. Another positive effect due to the oily waste addition was the requirement of extra humidity, due to the hydrophobic properties of this specific waste, which may imply reduced need of a bulking agent. Moreover, this study shows that composting can be a feasible way of adding value to fatty wastes. The three final composts presented very similar and suitable properties for land application.
Abstract: Headphones and earphones have many extremely small
holes or narrow slits; they use sound-absorbing or porous material (i.e.,
dampers) to suppress vibratory system resonance. The air viscosity in
these acoustic paths greatly affects the acoustic properties. Simulation
analyses such as the finite element method (FEM) therefore require
knowledge of the material properties of sound-absorbing or porous
materials, such as the characteristic impedance and propagation
constant. The transfer function method using acoustic tubes is a widely
known measuring method, but there is no literature on taking
measurements up to the audible range. To measure the acoustic
properties at high-range frequencies, the acoustic tubes that form the
measuring device need to be narrowed, and the distance between the
two microphones needs to be reduced. However, when the tubes are
narrowed, the characteristic impedance drops below the air impedance.
In this study, we considered the effect of air viscosity in an acoustical
tube, introduced a theoretical formula for this effect in the form of
complex density and complex sonic velocity, and verified the
theoretical formula. We also conducted an experiment and observed
the effect from air viscosity in the actual measurements.
Abstract: This paper presents a new function expansion method for finding traveling wave solutions of a nonlinear equations and calls it the G G -expansion method, given by Wang et al recently. As an application of this new method, we study the well-known Sawada-Kotera-Kadomtsev-Petviashivili equation and Bogoyavlensky-Konoplechenko equation. With two new expansions, general types of soliton solutions and periodic solutions for these two equations are obtained.
Abstract: In this study, the theoretical relationship between pressure and density was investigated on cylindrical hollow fuel briquettes produced of a mixture of fibrous biomass material using a screw press without any chemical binder. The fuel briquettes were made of biomass and other waste material such as spent coffee beans, mielie husks, saw dust and coal fines under pressures of 0.878-2.2 Mega Pascals (MPa). The material was densified into briquettes of outer diameter of 100mm, inner diameter of 35mm and 50mm long. It was observed that manual screw compression action produces briquettes of relatively low density as compared to the ones made using hydraulic compression action. The pressure and density relationship was obtained in the form of power law and compare well with other cylindrical solid briquettes made using hydraulic compression action. The produced briquettes have a dry density of 989 kg/m3 and contain 26.30% fixed carbon, 39.34% volatile matter, 10.9% moisture and 10.46% ash as per dry proximate analysis. The bomb calorimeter tests have shown the briquettes yielding a gross calorific value of 18.9MJ/kg.
Abstract: This paper presents a comparison of average outgoing
quality limit of the MCSP-2-C plan with MCSP-C when MCSP-2-C
has been developed from MCSP-C. The parameters used in MCSP-2-
C are: i (the clearance number), c (the acceptance number), m (the
number of conforming units to be found before allowing c nonconforming
units in the sampling inspection), f1 and f2 (the sampling
frequency at level 1 and 2, respectively). The average outgoing
quality limit (AOQL) values from two plans were compared and we
found that for all sets of i, r, and c values, MCSP-2-C gives higher
values than MCSP-C. For all sets of i, r, and c values, the average
outgoing quality values of MCSP-C and MCSP-2-C are similar when
p is low or high but is difference when p is moderate.
Abstract: A numerical method is proposed to calculate damping
properties for sound-proof structures involving elastic body,
viscoelastic body, and porous media. For elastic and viscoelastic body
displacement is modeled using conventional finite elements including
complex modulus of elasticity. Both effective density and bulk
modulus have complex quantities to represent damped sound fields in
the porous media. Particle displacement in the porous media is
discretised using finite element method. Displacement vectors as
common unknown variables are solved under coupled condition
between elastic body, viscoelastic body and porous media. Further,
explicit expressions of modal loss factor for the mixed structures are
derived using asymptotic method. Eigenvalue analysis and frequency
responded were calculated for automotive test panel laminated
viscoelastic and porous structures using this technique, the results
almost agreed with the experimental results.
Abstract: There are three possible effects of Special Theory of
Relativity (STR) on a thermodynamic system. Planck and Einstein
looked upon this process as isobaric; on the other hand Ott saw it as
an adiabatic process. However plenty of logical reasons show that the
process is isotherm. Our phenomenological consideration
demonstrates that the temperature is invariant with Lorenz
transformation. In that case process is isotherm, so volume and
pressure are Lorentz covariant. If the process is isotherm the Boyles
law is Lorentz invariant. Also equilibrium constant and Gibbs energy,
activation energy, enthalpy entropy and extent of the reaction became
Lorentz invariant.
Abstract: We present a dual-band (Cellular & PCS) dual-path
zero-IF receiver for CDMA2000 diversity, monitoring and
simultaneous-GPS. The secondary path is a SAW-less diversity
CDMA receiver which can be also used for advanced features like
monitoring when supported with an additional external VCO. A GPS
receiver is integrated with its dedicated VCO allowing simultaneous
positioning during a cellular call. The circuit is implemented in a
0.25μm 40GHz-fT BiCMOS process and uses a HVQFN 56-pin
package. It consumes a maximum 300mW from a 2.8V supply in
dual-modes. The chip area is 12.8mm2.
Abstract: Electro Discharge Sawing is a hybrid process
combining the features of SEDM and ECM. Its major characteristic is
extremely fast erosion rate compare to either of the above processes.
This paper brings out its relative feature of SEDM and EDS about
their erosion rates, surface roughness, and morphology of machined
surfaces.
Abstract: Nowaday-s, many organizations use systems that
support business process as a whole or partially. However, in some
application domains, like software development and health care
processes, a normative Process Aware System (PAS) is not suitable,
because a flexible support is needed to respond rapidly to new
process models. On the other hand, a flexible Process Aware System
may be vulnerable to undesirable and fraudulent executions, which
imposes a tradeoff between flexibility and security. In order to make
this tradeoff available, a genetic-based anomaly detection model for
logs of Process Aware Systems is presented in this paper. The
detection of an anomalous trace is based on discovering an
appropriate process model by using genetic process mining and
detecting traces that do not fit the appropriate model as anomalous
trace; therefore, when used in PAS, this model is an automated
solution that can support coexistence of flexibility and security.
Abstract: This paper examines the problem of designing a robust H∞ filter for a class of uncertain fuzzy descriptor systems described by a Takagi-Sugeno (TS) fuzzy model. Based on a linear matrix inequality (LMI) approach, LMI-based sufficient conditions for the uncertain nonlinear descriptor systems to have an H∞ performance are derived. To alleviate the ill-conditioning resulting from the interaction of slow and fast dynamic modes, solutions to the problem are given in terms of linear matrix inequalities which are independent of the singular perturbation ε, when ε is sufficiently small. The proposed approach does not involve the separation of states into slow and fast ones and it can be applied not only to standard, but also to nonstandard uncertain nonlinear descriptor systems. A numerical example is provided to illustrate the design developed in this paper.
Abstract: Genetically modified (GM) technology in food
production continued to generate controversies. Consumers were
concerned with the GM foods about the healthy and environmental
risks. While consumers- acceptance was a critical factor affecting how
widely this technology be used. According to the research review,
consumers- lack of information was one of the reasons to explain
consumers- low acceptance toward GM foods. The objective for this
study wanted to find out would informative product package affect
consumers- behavior toward GM foods. An experiment was designed
to investigate consumer behavior toward different product package
information. The results indicated that the product package
information influenced consumer product trust toward GM foods.
Compared with the traceability production system information, the
information about the GM rice was approved by authorized
organizations could increase consumers product trust in GM foods.
Consumers in Taiwan saw the information provided by authorized
organizations more credible than other information.
Abstract: This paper developed the c-Chart based on a Zero- Inflated Poisson (ZIP) processes that approximated by a geometric distribution with parameter p. The p estimated that fit for ZIP distribution used in calculated the mean, median, and variance of geometric distribution for constructed the c-Chart by three difference methods. For cg-Chart, developed c-Chart by used the mean and variance of the geometric distribution constructed control limits. For cmg-Chart, the mean used for constructed the control limits. The cme- Chart, developed control limits of c-Chart from median and variance values of geometric distribution. The performance of charts considered from the Average Run Length and Average Coverage Probability. We found that for an in-control process, the cg-Chart is superior for low level of mean at all level of proportion zero. For an out-of-control process, the cmg-Chart and cme-Chart are the best for mean = 2, 3 and 4 at all level of parameter.
Abstract: Due to the limited lifetime of the nodes in ad hoc and sensor networks, energy efficiency needs to be an important design consideration in any routing algorithm. It is known that by employing a virtual backbone in a wireless network, the efficiency of any routing scheme for the network can be improved. One common design for routing protocols in mobile ad hoc networks is to use positioning information; we use the node-s geometric locations to introduce an algorithm that can construct the virtual backbone structure locally in 3D environment. The algorithm construction has a constant time.