Abstract: Geosynthetics have proved to be suitable for
reinforced soil retaining walls. Based on the increasing uses of
geosynthetic reinforced soil systems in the regions, which bear
frequent earthquakes, the study of dynamic behavior of structures
seems necessary. Determining the reinforcement forces is; therefore,
one of the most important and main points of discussions in
designing retaining walls, by which we prevent from conservative
planning. Thus, this paper intended to investigate the effects of such
parameters as wall height, acceleration type, vertical spacing of
reinforcement, type of reinforcement and soil type on forces and
deformation through numerical modeling of the geosynthetic
reinforced soil retaining walls (GRSRW) under dynamic loading with
finite difference method by using FLAC. The findings indicate rather
positive results with each parameter.
Abstract: The paper investigates downtrend algorithm and
trading strategy based on chart pattern recognition and technical
analysis in futures market. The proposed chart formation is a pattern
with the lowest low in the middle and one higher low on each side.
The contribution of this paper lies in the reinforcement of statements
about the profitability of momentum trend trading strategies.
Practical benefit of the research is a trading algorithm in falling
markets and back-test analysis in futures markets. When based on
daily data, the algorithm has generated positive results, especially
when the market had downtrend period. Downtrend algorithm can be
applied as a hedge strategy against possible sudden market crashes.
The proposed strategy can be interesting for futures traders, hedge
funds or scientific researchers performing technical or algorithmic
market analysis based on momentum trend trading.
Abstract: Investigating language acquisition is one of the most
challenging problems in the area of studying language. Syllable
learning as a level of language acquisition has a considerable
significance since it plays an important role in language acquisition.
Because of impossibility of studying language acquisition directly
with children, especially in its developmental phases, computer
models will be useful in examining language acquisition. In this
paper a computer model of early language learning for syllable
learning is proposed. It is guided by a conceptual model of syllable
learning which is named Directions Into Velocities of Articulators
model (DIVA). The computer model uses simple associational and
reinforcement learning rules within neural network architecture
which are inspired by neuroscience. Our simulation results verify the
ability of the proposed computer model in producing phonemes
during babbling and early speech. Also, it provides a framework for
examining the neural basis of language learning and communication
disorders.
Abstract: Bead-on-plate welds were carried out on AISI 316L
(N) austenitic stainless steel (ASS) using flux cored arc welding
(FCAW) process. The bead on plates weld was conducted as per L25
orthogonal array. In this paper, the weld bead geometry such as depth
of penetration (DOP), bead width (BW) and weld reinforcement (R)
of AISI 316L (N) ASS are investigated. Taguchi approach is used as
statistical design of experiment (DOE) technique for optimizing the
selected welding input parameters. Grey relational analysis and
desirability approach are applied to optimize the input parameters
considering multiple output variables simultaneously. Confirmation
experiment has also been conducted to validate the optimized
parameters.
Abstract: Ambiguities in effects of earthquake on various
structures in all earthquake codes would necessitate more study and
research concerning influential factors on dynamic behavior.
Previous studies which were done on different features in different
buildings play a major role in the type of response a structure makes
to lateral vibrations. Diagnosing each of these irregularities can help
structure designers in choosing appropriate setbacks for decreasing
possible damages. Therefore vertical setback is one of the irregularity
factors in the height of the building where can be seen in skyscrapers
and hotels. Previous researches reveal notable changes in the place of
these setbacks showing dynamic response of the structure.
Consequently analyzing 48 models of concrete frames for 3, 6 and 9
stories heights with three different bays in general shape of a surface
decline by height have been constructed in ETABS2000 software,
and then the shape effect of each and every one of these frames in
period scale has been discussed. The result of this study reveals that
not only mass, stiffness and height but also shape of the frame is
influential.
Abstract: Emphasis on the advancement of new materials and technology has been there for the past few decades. The global development towards using cheap and durable materials from renewable resources contributes to sustainable development. An experimental investigation of mechanical behaviour of sisal fibre-reinforced concrete is reported for making a suitable building material in terms of reinforcement. Fibre reinforced Composite is one such material, which has reformed the concept of high strength. Sisal fibres are abundantly available in the hot areas. Sisal fibre has emerged as a reinforcing material for concretes, used in civil structures. In this work, properties such as hardness and tensile strength of sisal fibre reinforced cement composites with 6, 12, 18 and 24% by weight of sisal fibres were assessed. Sisal fibre reinforced cement composite slabs with long sisal fibres were manufactured using a cast hand lay up technique. Mechanical response was measured under tension. The high energy absorption capacity of the developed composite system was reflected in high toughness values under tension respectively.
Abstract: Modeling the behavior of the dialogue management in
the design of a spoken dialogue system using statistical methodologies
is currently a growing research area. This paper presents a work
on developing an adaptive learning approach to optimize dialogue
strategy. At the core of our system is a method formalizing dialogue
management as a sequential decision making under uncertainty whose
underlying probabilistic structure has a Markov Chain. Researchers
have mostly focused on model-free algorithms for automating the
design of dialogue management using machine learning techniques
such as reinforcement learning. But in model-free algorithms there
exist a dilemma in engaging the type of exploration versus exploitation.
Hence we present a model-based online policy learning
algorithm using interconnected learning automata for optimizing
dialogue strategy. The proposed algorithm is capable of deriving
an optimal policy that prescribes what action should be taken in
various states of conversation so as to maximize the expected total
reward to attain the goal and incorporates good exploration and
exploitation in its updates to improve the naturalness of humancomputer
interaction. We test the proposed approach using the most
sophisticated evaluation framework PARADISE for accessing to the
railway information system.
Abstract: Reinforced concrete crash barriers used in road traffic
must meet a number of criteria. Crash barriers are laid lengthwise,
one behind another, and joined using specially designed steel locks.
While developing BSV reinforced concrete crash barriers (type
ŽPSV), experiments and calculations aimed to optimize the shape of
a newly designed lock and the reinforcement quantity and
distribution in a crash barrier were carried out. The tension carrying
capacity of two parallelly joined locks was solved experimentally.
Based on the performed experiments, adjustments of nonlinear
properties of steel were performed in the calculations. The obtained
results served as a basis to optimize the lock design using a
computational model that takes into account the plastic behaviour of
steel and the influence of the surrounding concrete [6]. The response
to the vehicle impact has been analyzed using a specially elaborated
complex computational model, comprising both the nonlinear model
of the damping wall or crash barrier and the detailed model of the
vehicle [7].
Abstract: A different concept for designing and detailing of
reinforced concrete precast frame structures is analyzed in this paper.
The new detailing of the joints derives from the special hybrid
moment frame joints. The special reinforcements of this alternative
detailing, named modified special hybrid joint, are bondless with
respect to both column and beams. Full scale tests were performed on
a plan model, which represents a part of 5 story structure, cropped in
the middle of the beams and columns spans. Theoretical approach
was developed, based on testing results on twice repaired model,
subjected to lateral seismic type loading. Discussion regarding the
modified special hybrid joint behavior and further on widening
research needed concludes the presentation.
Abstract: Conceptualization strengthens intelligent systems in generalization skill, effective knowledge representation, real-time inference, and managing uncertain and indefinite situations in addition to facilitating knowledge communication for learning agents situated in real world. Concept learning introduces a way of abstraction by which the continuous state is formed as entities called concepts which are connected to the action space and thus, they illustrate somehow the complex action space. Of computational concept learning approaches, action-based conceptualization is favored because of its simplicity and mirror neuron foundations in neuroscience. In this paper, a new biologically inspired concept learning approach based on the probabilistic framework is proposed. This approach exploits and extends the mirror neuron-s role in conceptualization for a reinforcement learning agent in nondeterministic environments. In the proposed method, instead of building a huge numerical knowledge, the concepts are learnt gradually from rewards through interaction with the environment. Moreover the probabilistic formation of the concepts is employed to deal with uncertain and dynamic nature of real problems in addition to the ability of generalization. These characteristics as a whole distinguish the proposed learning algorithm from both a pure classification algorithm and typical reinforcement learning. Simulation results show advantages of the proposed framework in terms of convergence speed as well as generalization and asymptotic behavior because of utilizing both success and failures attempts through received rewards. Experimental results, on the other hand, show the applicability and effectiveness of the proposed method in continuous and noisy environments for a real robotic task such as maze as well as the benefits of implementing an incremental learning scenario in artificial agents.
Abstract: Ten simply supported grossly underreinforced
tapered concrete beams of full size were tested upto complete
collapse under flexural effect .Out of 10 beams, 5 beams were
nonfibrous and the remaining beams contained fibres. The beams
had a variation in the tapered angle as 2°, 4°, 6°, 8° and 10°. The
concrete mix, conventional steel and the type of fibre used were
held constant. Flat corrugated steel fibres were utilized as
secondary reinforcement. The strength and stability parameters
were measured. It is established that the fibrous tapered beams can
be used economically in earthquake prone areas.
Abstract: The large and small-scale shaking table tests, which
was conducted for investigating damage evolution of piles inside
liquefied soil, are numerically simulated and experimental verified by the3D nonlinear finite element analysis. Damage evolution of
elasto-plastic circular steel piles and reinforced concrete (RC) one with cracking and yield of reinforcement are focused on, and the failure patterns and residual damages are captured by the proposed constitutive models. The superstructure excitation behind quay wall is
reproduced as well.
Abstract: In this paper, the torsion capacity of ultimate point on rectangular beams with spiral reinforcements in the torsion direction and its anti-direction are investigated. Therefore, models of above-mentioned beams have been numerically analyzed under various loads using ANSYS software. It was observed that, spirallyreinforced prismatic beam and beam with spiral links, show lower torsion capacity than beam with normal links also in anti-direction. The result is that the concrete regulations are violated in this case.
Abstract: Particulate reinforced metal matrix composites
(MMCs) are potential materials for various applications due to their
advantageous of physical and mechanical properties. This paper
presents a study on the performance of stir cast Al2O3 SiC reinforced
metal matrix composite materials. The results indicate that the
composite materials exhibit improved physical and mechanical
properties, such as, low coefficient of thermal expansion, high
ultimate tensile strength, high impact strength, and hardness. It has
been found that with the increase of weight percentage of
reinforcement particles in the aluminium metal matrix, the new
material exhibits lower wear rate against abrasive wearing. Being
extremely lighter than the conventional gray cast iron material, the
Al-Al2O3 and Al-SiC composites could be potential green materials
for applications in the automobile industry, for instance, in making
car disc brake rotors.
Abstract: In this work a visual and reactive contour following
behaviour is learned by reinforcement. With artificial vision the
environment is perceived in 3D, and it is possible to avoid obstacles
that are invisible to other sensors that are more common in mobile
robotics. Reinforcement learning reduces the need for intervention in
behaviour design, and simplifies its adjustment to the environment,
the robot and the task. In order to facilitate its generalisation to other
behaviours and to reduce the role of the designer, we propose a
regular image-based codification of states. Even though this is much
more difficult, our implementation converges and is robust. Results
are presented with a Pioneer 2 AT on a Gazebo 3D simulator.
Abstract: Australia, while being a large and eager consumer of
innovative and cutting edge Information and Communication
Technologies (ICT), continues to struggle to remain a leader in
Technological Innovation. This paper has two main contributions to
address certain aspects of this complex issue. The first being the
current findings of an ongoing research project on Information and
Innovation Management in the Australian Information and
Communication Technologies (ICT) sector. The major issues being
considered by the project include: investigation of the possible
inherent entrepreneurial nature of ICT; how to foster ICT innovation;
and examination of the inherent difficulties currently found within
the ICT industry of Australia in regards to supporting the
development of innovative and creative ideas. The second major
contribution is details of the I.-C.A.N. (Innovation by Collaborative
Anonymous Networking) software application information
management tool created and evolving in our research group. I-CAN,
besides having a positive reinforcement acronym, is aimed at
facilitating productive collaborative innovation in an Australian
workplace. Such a work environment is frequently subjected to
cultural influences such as the 'tall poppy syndrome' and 'negative'
or 'unconstructive' peer-pressure. There influences are frequently
seen as inhibitors to employee participation, entrepreneurship and
innovation.
Abstract: Nanostructured materials have attracted many
researchers due to their outstanding mechanical and physical
properties. For example, carbon nanotubes (CNTs) or carbon
nanofibres (CNFs) are considered to be attractive reinforcement
materials for light weight and high strength metal matrix composites.
These composites are being projected for use in structural
applications for their high specific strength as well as functional
materials for their exciting thermal and electrical characteristics. The
critical issues of CNT-reinforced MMCs include processing
techniques, nanotube dispersion, interface, strengthening mechanisms
and mechanical properties. One of the major obstacles to the effective
use of carbon nanotubes as reinforcements in metal matrix
composites is their agglomeration and poor distribution/dispersion
within the metallic matrix. In order to tap into the advantages of the
properties of CNTs (or CNFs) in composites, the high dispersion of
CNTs (or CNFs) and strong interfacial bonding are the key issues
which are still challenging. Processing techniques used for synthesis
of the composites have been studied with an objective to achieve
homogeneous distribution of carbon nanotubes in the matrix.
Modified mechanical alloying (ball milling) techniques have emerged
as promising routes for the fabrication of carbon nanotube (CNT)
reinforced metal matrix composites. In order to obtain a
homogeneous product, good control of the milling process, in
particular control of the ball movement, is essential. The control of
the ball motion during the milling leads to a reduction in grinding
energy and a more homogeneous product. Also, the critical inner
diameter of the milling container at a particular rotational speed can
be calculated. In the present work, we use conventional and modified
mechanical alloying to generate a homogenous distribution of 2 wt.
% CNT within Al powders. 99% purity Aluminium powder (Acros,
200mesh) was used along with two different types of multiwall
carbon nanotube (MWCNTs) having different aspect ratios to
produce Al-CNT composites. The composite powders were processed
into bulk material by compaction, and sintering using a cylindrical
compaction and tube furnace. Field Emission Scanning electron
microscopy (FESEM), X-Ray diffraction (XRD), Raman
spectroscopy and Vickers macro hardness tester were used to
evaluate CNT dispersion, powder morphology, CNT damage, phase
analysis, mechanical properties and crystal size determination.
Despite the success of ball milling in dispersing CNTs in Al powder,
it is often accompanied with considerable strain hardening of the Al
powder, which may have implications on the final properties of the
composite. The results show that particle size and morphology vary
with milling time. Also, by using the mixing process and sonication
before mechanical alloying and modified ball mill, dispersion of the
CNTs in Al matrix improves.
Abstract: Reinforced concrete has good durability and excellent structural performance. But there are cases of early deterioration due to a number of factors, one prominent factor being corrosion of steel reinforcement. The process of corrosion sets in due to ingress of moisture, oxygen and other ingredients into the body of concrete, which is unsound, permeable and absorbent. Cracks due to structural and other causes such as creep, shrinkage, etc also allow ingress of moisture and other harmful ingredients and thus accelerate the rate of corrosion. There are several interactive factors both external and internal, which lead to corrosion of reinforcement and ultimately failure of structures. Suitable addition of mineral admixture like silica fume (SF) in concrete improves the strength and durability of concrete due to considerable improvement in the microstructure of concrete composites, especially at the transition zone. Secondary reinforcement in the form of fibre is added to concrete, which provides three dimensional random reinforcement in the entire mass of concrete. Reinforced concrete beams of size 0.1 m X 0.15 m and length 1m have been cast using M 35 grade of concrete. The beams after curing process were subjected to corrosion process by impressing an external Direct Current (Galvanostatic Method) for a period of 15 days under stressed and unstressed conditions. The corroded beams were tested by applying two point loads to determine the ultimate load carrying capacity and cracking pattern and the results of specimens were compared with that of the companion specimens. Gravimetric method is used to quantify corrosion that has occurred.
Abstract: RoboCup Rescue simulation as a large-scale Multi
agent system (MAS) is one of the challenging environments for
keeping coordination between agents to achieve the objectives
despite sensing and communication limitations. The dynamicity of
the environment and intensive dependency between actions of
different kinds of agents make the problem more complex. This point
encouraged us to use learning-based methods to adapt our decision
making to different situations. Our approach is utilizing
reinforcement leaning. Using learning in rescue simulation is one of
the current ways which has been the subject of several researches in
recent years. In this paper we present an innovative learning method
implemented for Police Force (PF) Agent. This method can cope
with the main difficulties that exist in other learning approaches.
Different methods used in the literature have been examined. Their
drawbacks and possible improvements have led us to the method
proposed in this paper which is fast and accurate. The Brain
Emotional Learning Based Intelligent Controller (BELBIC) is our
solution for learning in this environment. BELBIC is a
physiologically motivated approach based on a computational model
of amygdale and limbic system. The paper presents the results
obtained by the proposed approach, showing the power of BELBIC
as a decision making tool in complex and dynamic situation.
Abstract: The nearly 21-year-old Jiujiang Bridge, which is suffering from uneven line shape, constant great downwarping of the main beam and cracking of the box girder, needs reinforcement and cable adjustment. It has undergone cable adjustment for twice with incomplete data. Therefore, the initial internal force state of the Jiujiang Bridge is identified as the key for the cable adjustment project. Based on parameter identification by means of static force test data, this paper suggests determining the initial internal force state of the cable-stayed bridge according to the cable force-displacement relationship parameter identification method. That is, upon measuring the displacement and the change in cable forces for twice, one can identify the parameters concerned by means of optimization. This method is applied to the cable adjustment, replacement and reinforcement project for the Jiujiang Bridge as a guidance for the cable adjustment and reinforcement project of the bridge.