Abstract: This paper describes the development of a fully
automated measurement software for antenna radiation pattern
measurements in a Compact Antenna Test Range (CATR). The
CATR has a frequency range from 2-40 GHz and the measurement
hardware includes a Network Analyzer for transmitting and
Receiving the microwave signal and a Positioner controller to control
the motion of the Styrofoam column. The measurement process
includes Calibration of CATR with a Standard Gain Horn (SGH)
antenna followed by Gain versus angle measurement of the Antenna
under test (AUT). The software is designed to control a variety of
microwave transmitter / receiver and two axis Positioner controllers
through the standard General Purpose interface bus (GPIB) interface.
Addition of new Network Analyzers is supported through a slight
modification of hardware control module. Time-domain gating is
implemented to remove the unwanted signals and get the isolated
response of AUT. The gated response of the AUT is compared with
the calibration data in the frequency domain to obtain the desired
results. The data acquisition and processing is implemented in
Agilent VEE and Matlab. A variety of experimental measurements
with SGH antennas were performed to validate the accuracy of
software. A comparison of results with existing commercial
softwares is presented and the measured results are found to be
within .2 dBm.
Abstract: In this work we present a solution for DAGC (Digital
Automatic Gain Control) in WLAN receivers compatible to IEEE 802.11a/g standard. Those standards define communication in 5/2.4
GHz band using Orthogonal Frequency Division Multiplexing OFDM modulation scheme. WLAN Transceiver that we have used
enables gain control over Low Noise Amplifier (LNA) and a
Variable Gain Amplifier (VGA). The control over those signals is
performed in our digital baseband processor using dedicated hardware block DAGC. DAGC in this process is used to automatically control the VGA and LNA in order to achieve better
signal-to-noise ratio, decrease FER (Frame Error Rate) and hold the
average power of the baseband signal close to the desired set point.
DAGC function in baseband processor is done in few steps: measuring power levels of baseband samples of an RF signal,accumulating the differences between the measured power level and
actual gain setting, adjusting a gain factor of the accumulation, and
applying the adjusted gain factor the baseband values. Based on the measurement results of RSSI signal dependence to input power we have concluded that this digital AGC can be implemented applying
the simple linearization of the RSSI. This solution is very simple but also effective and reduces complexity and power consumption of the
DAGC. This DAGC is implemented and tested both in FPGA and in ASIC as a part of our WLAN baseband processor. Finally, we have integrated this circuit in a compact WLAN PCMCIA board based on MAC and baseband ASIC chips designed from us.
Abstract: Multiple-input multiple-output (MIMO) systems are
widely in use to improve quality, reliability of wireless transmission
and increase the spectral efficiency. However in MIMO systems,
multiple copies of data are received after experiencing various
channel effects. The limitations on account of complexity due to
number of antennas in case of conventional decoding techniques have
been looked into. Accordingly we propose a modified sphere decoder
(MSD-1) algorithm with lower complexity and give rise to system
with high spectral efficiency. With the aim to increase signal
diversity we apply rotated quadrature amplitude modulation (QAM)
constellation in multi dimensional space. Finally, we propose a new
architecture involving space time trellis code (STTC) concatenated
with space time block code (STBC) using MSD-1 at the receiver for
improving system performance. The system gains have been verified
with channel state information (CSI) errors.
Abstract: In this paper, an adaptive polarized Multiple-Input
Multiple-Output (MIMO) Multicarrier Spread Spectrum Code Division Multiple Access (MC-SS-CDMA) system is designed for downlink mobile communications. The proposed system will be
examined in Frequency Division Duplex (FDD) mode for both macro urban and suburban environments. For the same transmission
bandwidth, a performance comparison between both nonoverlapped and orthogonal Frequency Division Multiplexing (FDM) schemes will be presented. Also, the proposed system will be compared with
both the closed loop vertical MIMO MC-SS-CDMA system and the
synchronous vertical STBC-MIMO MC-SS-CDMA system. As will
be shown, the proposed system introduces a significant performance
gain as well as reducing the spatial dimensions of the MIMO system
and simplifying the receiver implementation. The effect of the
polarization diversity characteristics on the BER performance will be
discussed. Also, the impact of excluding the cross-polarization MCSS-
CDMA blocks in the base station will be investigated. In addition,
the system performance will be evaluated under different Feedback
Information (FBI) rates for slowly-varying channels. Finally, a
performance comparison for vehicular and pedestrian environments
will be presented
Abstract: In the context of spectrum surveillance, a method to
recover the code of spread spectrum signal is presented, whereas the
receiver has no knowledge of the transmitter-s spreading sequence.
The approach is based on a genetic algorithm (GA), which is forced to
model the received signal. Genetic algorithms (GAs) are well known
for their robustness in solving complex optimization problems.
Experimental results show that the method provides a good
estimation, even when the signal power is below the noise power.
Abstract: In this work, we study the problem of determining
the minimum scheduling length that can satisfy end-to-end (ETE)
traffic demand in scheduling-based multihop WSNs with cooperative
multiple-input multiple-output (MIMO) transmission scheme. Specifically,
we present a cross-layer formulation for the joint routing,
scheduling and stream control problem by incorporating various
power and rate adaptation schemes, and taking into account an
antenna beam pattern model and the signal-to-interference-and-noise
(SINR) constraint at the receiver. In the context, we also propose
column generation (CG) solutions to get rid of the complexity
requiring the enumeration of all possible sets of scheduling links.
Abstract: This paper investigates the problem of spreading
sequence and receiver code synchronization techniques for satellite
based CDMA communications systems. The performance of CDMA
system depends on the autocorrelation and cross-correlation
properties of the used spreading sequences. In this paper we propose
the uses of chaotic Lu system to generate binary sequences for
spreading codes in a direct sequence spread CDMA system. To
minimize multiple access interference (MAI) we propose the use of
genetic algorithm for optimum selection of chaotic spreading
sequences. To solve the problem of transmitter-receiver
synchronization, we use the passivity controls. The concept of
semipassivity is defined to find simple conditions which ensure
boundedness of the solutions of coupled Lu systems. Numerical
results are presented to show the effectiveness of the proposed
approach.
Abstract: It is well known that the channel capacity of Multiple-
Input-Multiple-Output (MIMO) system increases as the number of
antenna pairs between transmitter and receiver increases but it suffers
from multiple expensive RF chains. To reduce the cost of RF chains,
Antenna Selection (AS) method can offer a good tradeoff between
expense and performance. In a transmitting AS system, Channel
State Information (CSI) feedback is necessarily required to choose
the best subset of antennas in which the effects of delays and errors
occurred in feedback channels are the most dominant factors
degrading the performance of the AS method. This paper presents the
concept of AS method using CSI from channel reciprocity instead of
feedback method. Reciprocity technique can easily archive CSI by
utilizing a reverse channel where the forward and reverse channels
are symmetrically considered in time, frequency and location. In this
work, the capacity performance of MIMO system when using AS
method at transmitter with reciprocity channels is investigated by
own developing Testbed. The obtained results show that reciprocity
technique offers capacity close to a system with a perfect CSI and
gains a higher capacity than a system without AS method from 0.9 to
2.2 bps/Hz at SNR 10 dB.
Abstract: Spam mails are unwanted mails sent to large number
of users. Spam mails not only consume the network resources, but
cause security threats as well. This paper proposes an efficient
technique to detect, and to prevent spam mail in the sender side rather
than the receiver side. This technique is based on a counter set on the
sender server. When a mail is transmitted to the server, the mail server
checks the number of the recipients based on its counter policy. The
counter policy performed by the mail server is based on some
pre-defined criteria. When the number of recipients exceeds the
counter policy, the mail server discontinues the rest of the process, and
sends a failure mail to sender of the mail; otherwise the mail is
transmitted through the network. By using this technique, the usage of
network resources such as bandwidth, and memory is preserved. The
simulation results in real network show that when the counter is set on
the sender side, the time required for spam mail detection is 100 times
faster than the time the counter is set on the receiver side, and the
network resources are preserved largely compared with other
anti-spam mail techniques in the receiver side.
Abstract: Overloading is a technique to accommodate more
number of users than the spreading factor N. This is a bandwidth
efficient scheme to increase the number users in a fixed bandwidth.
One of the efficient schemes to overload a CDMA system is to use
two sets of orthogonal signal waveforms (O/O). The first set is
assigned to the N users and the second set is assigned to the
additional M users. An iterative interference cancellation technique is
used to cancel interference between the two sets of users. In this
paper, the performance of an overloading scheme in which the first N
users are assigned Walsh-Hadamard orthogonal codes and extra users
are assigned the same WH codes but overlaid by a fixed (quasi) bent
sequence [11] is evaluated. This particular scheme is called Quasi-
Orthogonal Sequence (QOS) O/O scheme, which is a part of
cdma2000 standard [12] to provide overloading in the downlink
using single user detector. QOS scheme are balance O/O scheme,
where the correlation between any set-1 and set-2 users are
equalized. The allowable overload of this scheme is investigated in
the uplink on an AWGN and Rayleigh fading channels, so that the
uncoded performance with iterative multistage interference
cancellation detector remains close to the single user bound. It is
shown that this scheme provides 19% and 11% overloading with
SDIC technique for N= 16 and 64 respectively, with an SNR
degradation of less than 0.35 dB as compared to single user bound at
a BER of 0.00001. But on a Rayleigh fading channel, the channel
overloading is 45% (29 extra users) at a BER of 0.0005, with an SNR
degradation of about 1 dB as compared to single user performance
for N=64. This is a significant amount of channel overloading on a
Rayleigh fading channel.
Abstract: We describe an effective method for image encryption
which employs magnitude and phase manipulation using carrier
images. Although it involves traditional methods like magnitude and
phase encryptions, the novelty of this work lies in deploying the
concept of carrier images for encryption purpose. To this end, a
carrier image is randomly chosen from a set of stored images. One
dimensional (1-D) discrete Fourier transform (DFT) is then carried
out on the original image to be encrypted along with the carrier
image. Row wise spectral addition and scaling is performed between
the magnitude spectra of the original and carrier images by randomly
selecting the rows. Similarly, row wise phase addition and scaling is
performed between the original and carrier images phase spectra by
randomly selecting the rows. The encrypted image obtained by these
two operations is further subjected to one more level of magnitude
and phase manipulation using another randomly chosen carrier image
by 1-D DFT along the columns. The resulting encrypted image is
found to be fully distorted, resulting in increasing the robustness
of the proposed work. Further, applying the reverse process at the
receiver, the decrypted image is found to be distortionless.
Abstract: The number of users supported in a DS-CDMA
cellular system is typically less than spreading factor (N), and the
system is said to be underloaded. Overloading is a technique to
accommodate more number of users than the spreading factor N. In
O/O overloading scheme, the first set is assigned to the N
synchronous users and the second set is assigned to the additional
synchronous users. An iterative multistage soft decision interference
cancellation (SDIC) receiver is used to remove high level of
interference between the two sets. Performance is evaluated in terms
of the maximum number acceptable users so that the system
performance is degraded slightly compared to the single user
performance at a specified BER. In this paper, the capacity of CDMA
based O/O overloading scheme is evaluated with SDIC receiver. It is
observed that O/O scheme using orthogonal Gold codes provides
25% channel overloading (N=64) for synchronous DS-CDMA
system on an AWGN channel in the uplink at a BER of 1e-5.For a
Rayleigh faded channel, the critical capacity is 40% at a BER of 5e-5
assuming synchronous users. But in practical systems, perfect chip
timing is very difficult to maintain in the uplink.. We have shown that
the overloading performance reduces to 11% for a timing
synchronization error of 0.02Tc for a BER of 1e-5.
Abstract: In this paper, a joint source-channel coding (JSCC) scheme for time-varying channels is presented. The proposed scheme uses hierarchical framework for both source encoder and transmission via QAM modulation. Hierarchical joint source channel codes with hierarchical QAM constellations are designed to track the channel variations which yields to a higher throughput by adapting certain parameters of the receiver to the channel variation. We consider the problem of still image transmission over time-varying channels with channel state information (CSI) available at 1) receiver only and 2) both transmitter and receiver being informed about the state of the channel. We describe an algorithm that optimizes hierarchical source codebooks by minimizing the distortion due to source quantizer and channel impairments. Simulation results, based on image representation, show that, the proposed hierarchical system outperforms the conventional schemes based on a single-modulator and channel optimized source coding.
Abstract: In this paper, a target signal detection method using
multiple signal classification (MUSIC) algorithm is proposed. The
MUSIC algorithm is a subspace-based direction of arrival (DOA)
estimation method. The algorithm detects the DOAs of multiple
sources using the inverse of the eigenvalue-weighted eigen spectra. To
apply the algorithm to target signal detection for GSC-based
beamforming, we utilize its spectral response for the target DOA in
noisy conditions. For evaluation of the algorithm, the performance of
the proposed target signal detection method is compared with that of
the normalized cross-correlation (NCC), the fixed beamforming, and
the power ratio method. Experimental results show that the proposed
algorithm significantly outperforms the conventional ones in receiver
operating characteristics(ROC) curves.
Abstract: This paper presents an analysis on the capacity and performance of MIMO-OFDM systems. The work is focused on the capacity of MIMO-OFDM systems over rician fading channel, in the case of the channel being known at the receiver only, which is more practical case of the channel. Simple expression for capacity is derived for the case of correlated rician fading. The performance of some MIMO-OFDM implementations with rician fading model is presented using an Alamouti coding scheme and Simulation results are obtained for both capacity and performance analysis.
Abstract: Functional gastrointestinal disorders affect millions of people spread all age regardless of race and sex. There are, however, rare diagnostic methods for the functional gastrointestinal disorders because functional disorders show no evidence of organic and physical causes. Our research group identified recently that the gastrointestinal tract well in the patients with the functional gastrointestinal disorders becomes more rigid than healthy people when palpating the abdominal regions overlaying the gastrointestinal tract. Aim of this study is, therefore, to develop a diagnostic system for the functional gastrointestinal disorders based on ultrasound technique, which can quantify the characteristic above related to the rigidity of the gastrointestinal tract well. Ultrasound system was designed. The system consisted of transmitter, ultrasonic transducer, receiver, TGC, and CPLD, and verified via a phantom test. For the phantom test, ten soft-tissue specimens were harvested from porcine. Five of them were then treated chemically to mimic a rigid condition of gastrointestinal tract well, which was induced by functional gastrointestinal disorders. Additionally, the specimens were tested mechanically to identify if the mimic was reasonable. The customized ultrasound system was finally verified through application to human subjects with/without functional gastrointestinal disorders (Normal and Patient Groups). It was identified from the mechanical test that the chemically treated specimens were more rigid than normal specimen. This finding was favorably compared with the result obtained from the phantom test. The phantom test also showed that ultrasound system well described the specimen geometric characteristics and detected an alteration in the specimens. The maximum amplitude of the ultrasonic reflective signal in the rigid specimens (0.2±0.1Vp-p) at the interface between the fat and muscle layers was explicitly higher than that in the normal specimens (0.1±0.0Vp-p). Clinical tests using our customized ultrasound system for human subject showed that the maximum amplitudes of the ultrasonic reflective signals near to the gastrointestinal tract well for the patient group (2.6±0.3Vp-p) were generally higher than those in normal group (0.1±0.2Vp-p). Here, maximum reflective signals was appeared at 20mm depth approximately from abdominal skin for all human subjects, corresponding to the location of the boundary layer close to gastrointestinal tract well. These results suggest that newly designed diagnostic system based on ultrasound technique may diagnose enough the functional gastrointestinal disorders.
Abstract: The design of chaos-based secure communication
via synchronized modified Chua-s systems is investigated in
this paper. A continuous control law is proposed to ensure
synchronization of the master and slave modified Chua-s
systems by using the variable structure control technique.
Particularly, the concept of extended systems is introduced
such that a continuous control input is obtained to avoid
chattering phenomenon. Then, it becomes possible to ensure
that the message signal embedded in the transmitter can be
recovered in the receiver.
Abstract: Study on suppression of interference in time domain equalizers is attempted for high data rate impulse radio (IR) ultra wideband communication system. The narrow band systems may cause interference with UWB devices as it is having very low transmission power and the large bandwidth. SRAKE receiver improves system performance by equalizing signals from different paths. This enables the use of SRAKE receiver techniques in IRUWB systems. But Rake receiver alone fails to suppress narrowband interference (NBI). A hybrid SRake-MMSE time domain equalizer is proposed to overcome this by taking into account both the effect of the number of rake fingers and equalizer taps. It also combats intersymbol interference. A semi analytical approach and Monte-Carlo simulation are used to investigate the BER performance of SRAKEMMSE receiver on IEEE 802.15.3a UWB channel models. Study on non-line of sight indoor channel models (both CM3 and CM4) illustrates that bit error rate performance of SRake-MMSE receiver with NBI performs better than that of Rake receiver without NBI. We show that for a MMSE equalizer operating at high SNR-s the number of equalizer taps plays a more significant role in suppressing interference.
Abstract: This paper presents an approach for early breast
cancer diagnostic by employing combination of artificial neural
networks (ANN) and multiwaveletpacket based subband image
decomposition. The microcalcifications correspond to high-frequency
components of the image spectrum, detection of microcalcifications
is achieved by decomposing the mammograms into different
frequency subbands,, reconstructing the mammograms from the
subbands containing only high frequencies. For this approach we
employed different types of multiwaveletpacket. We used the result
as an input of neural network for classification. The proposed
methodology is tested using the Nijmegen and the Mammographic
Image Analysis Society (MIAS) mammographic databases and
images collected from local hospitals. Results are presented as the
receiver operating characteristic (ROC) performance and are
quantified by the area under the ROC curve.
Abstract: This paper presents a remote on-line diagnostic system
for vehicles via the use of On-Board Diagnostic (OBD), GPS, and 3G
techniques. The main parts of the proposed system are on-board
computer, vehicle monitor server, and vehicle status browser. First,
the on-board computer can obtain the location of deriver and vehicle
status from GPS receiver and OBD interface, respectively. Then
on-board computer will connect with the vehicle monitor server
through 3G network to transmit the real time vehicle system status.
Finally, vehicle status browser could show the remote vehicle status
including vehicle speed, engine rpm, battery voltage, engine coolant
temperature, and diagnostic trouble codes. According to the
experimental results, the proposed system can help fleet managers and
car knockers to understand the remote vehicle status. Therefore this
system can decrease the time of fleet management and vehicle repair
due to the fleet managers and car knockers who find the diagnostic
trouble messages in time.