Abstract: In mechanical and environmental engineering, mixed
convection is a frequently encountered thermal fluid phenomenon
which exists in atmospheric environment, urban canopy flows, ocean
currents, gas turbines, heat exchangers, and computer chip cooling
systems etc... . This paper deals with a numerical investigation of
mixed convection in a vertical heated channel. This flow results from
the mixing of the up-going fluid along walls of the channel with the
one issued from a flat nozzle located in its entry section. The fluiddynamic
and heat-transfer characteristics of vented vertical channels
are investigated for constant heat-flux boundary conditions, a
Rayleigh number equal to 2.57 1010, for two jet Reynolds number
Re=3 103 and 2104 and the aspect ratio in the 8-20 range. The system
of governing equations is solved with a finite volumes method and an
implicit scheme. The obtained results show that the turbulence and
the jet-wall interaction activate the heat transfer, as does the drive of
ambient air by the jet. For low Reynolds number Re=3 103, the
increase of the aspect Ratio enhances the heat transfer of about 3%,
however; for Re=2 104, the heat transfer enhancement is of about
12%. The numerical velocity, pressure and temperature fields are
post-processed to compute the quantities of engineering interest such
as the induced mass flow rate, and average Nusselt number, in terms
of Rayleigh, Reynolds numbers and dimensionless geometric
parameters are presented.
Abstract: Turbulent heat transfer to fluid flow through channel with triangular ribs of different angles are presented in this paper. Ansys 14 ICEM and Ansys 14 Fluent are used for meshing process and solving Navier stokes equations respectively. In this investigation three angles of triangular ribs with the range of Reynolds number varied from 20000 to 60000 at constant surface temperature are considered. The results show that the Nusselt number increases with the increase of Reynolds number for all cases at constant surface temperature. According to the profile of local Nusselt number on ribs walled of channel, the peak is at the midpoint between the two ribs. The maximum value of average Nusselt number is obtained for triangular ribs of angel 60°and at Reynolds number of 60000 compared to the Nusselt number for the ribs of angel 90° and 45° and at same Reynolds number. The recirculation regions generated by the ribs corresponding to the velocity streamline show the largest recirculation region at triangular ribs of angle 60° which also provides the highest enhancement of heat transfer.
Abstract: The objective of the present work is to conduct
investigations leading to a more complete explanation of single phase
natural convective heat transfer in an enclosure with fin utilizing
nano fluids. The nano fluid used, which is composed of Aluminum
oxide nano particles in suspension of Ethylene glycol, is provided at
various volume fractions. The study is carried out numerically for a
range of Rayleigh numbers, fin heights and aspect ratio. The flow and
temperature distributions are taken to be two-dimensional. Regions
with the same velocity and temperature distributions are identified as
symmetry of sections. One half of such a rectangular region is chosen
as the computational domain taking into account the symmetry about
the fin. Transport equations are modeled by a stream functionvorticity
formulation and are solved numerically by finite-difference
schemes. Comparisons with previously published works on the basis
of special cases are done. Results are presented in the form of
streamline, vector and isotherm plots as well as the variation of local
Nusselt number along the fin under different conditions.
Abstract: This paper presents a numerical study on surface heat
transfer characteristics of laminar air flows in parallel-plate dimpled
channels. The two-dimensional numerical model is provided by
commercial code FLUENT and the results are obtained for channels
with symmetrically opposing hemi-cylindrical cavities onto both
walls for Reynolds number ranging from 1000 to 2500. The influence
of variations in relative depth of dimples (the ratio of cavity depth to
the cavity curvature diameter), the number of them and the thermophysical
properties of channel walls on heat transfer enhancement is
studied. The results are evident for existence of an optimum value for
the relative depth of dimples in which the largest wall heat flux and
average Nusselt number can be achieved. In addition, the results of
conjugation simulation indicate that the overall influence of the ratio
of wall thermal conductivity to the one of the fluid on heat transfer
rate is not much significant and can be ignored.
Abstract: Fluids are used for heat transfer in many engineering
equipments. Water, ethylene glycol and propylene glycol are some
of the common heat transfer fluids. Over the years, in an attempt to
reduce the size of the equipment and/or efficiency of the process,
various techniques have been employed to improve the heat transfer
rate of these fluids. Surface modification, use of inserts and
increased fluid velocity are some examples of heat transfer
enhancement techniques. Addition of milli or micro sized particles
to the heat transfer fluid is another way of improving heat transfer
rate. Though this looks simple, this method has practical problems
such as high pressure loss, clogging and erosion of the material of
construction. These problems can be overcome by using nanofluids,
which is a dispersion of nanosized particles in a base fluid.
Nanoparticles increase the thermal conductivity of the base fluid
manifold which in turn increases the heat transfer rate. In this work,
the heat transfer enhancement using aluminium oxide nanofluid has
been studied by computational fluid dynamic modeling of the
nanofluid flow adopting the single phase approach.
Abstract: Addition of milli or micro sized particles to the heat
transfer fluid is one of the many techniques employed for improving
heat transfer rate. Though this looks simple, this method has
practical problems such as high pressure loss, clogging and erosion
of the material of construction. These problems can be overcome by
using nanofluids, which is a dispersion of nanosized particles in a
base fluid. Nanoparticles increase the thermal conductivity of the
base fluid manifold which in turn increases the heat transfer rate.
Nanoparticles also increase the viscosity of the basefluid resulting in
higher pressure drop for the nanofluid compared to the base fluid. So
it is imperative that the Reynolds number (Re) and the volume
fraction have to be optimum for better thermal hydraulic
effectiveness. In this work, the heat transfer enhancement using
aluminium oxide nanofluid using low and high volume fraction
nanofluids in turbulent pipe flow with constant wall temperature has
been studied by computational fluid dynamic modeling of the
nanofluid flow adopting the single phase approach. Nanofluid, up till
a volume fraction of 1% is found to be an effective heat transfer
enhancement technique. The Nusselt number (Nu) and friction factor
predictions for the low volume fractions (i.e. 0.02%, 0.1 and 0.5%)
agree very well with the experimental values of Sundar and Sharma
(2010). While, predictions for the high volume fraction nanofluids
(i.e. 1%, 4% and 6%) are found to have reasonable agreement with
both experimental and numerical results available in the literature.
So the computationally inexpensive single phase approach can be
used for heat transfer and pressure drop prediction of new nanofluids.
Abstract: This study numerically investigates the effects of Electrohydrodynamic on flow patterns and heat transfer enhancement within a cavity which is on the lower wall of channel. In this simulation, effects of using ground wire and ground plate on the flow patterns are compared. Moreover, the positions of electrode wire respecting with ground are tested in the range of angles θ = 0 - 180o. High electrical voltage exposes to air is 20 kV. Bulk mean velocity and temperature of inlet air are controlled at 0.1 m/s and 60 OC, respectively. The result shows when electric field is applied, swirling flow is appeared in the channel. In addition, swirling flow patterns in the main flow of using ground plate are widely spreader than that of using ground wire. Moreover, direction of swirling flow also affects the flow pattern and heat transfer in a cavity. These cause the using ground wire to give the maximum temperature and heat transfer higher than using ground plate. Furthermore, when the angle is at θ = 60o, high shear flow effect is obtained. This results show high strength of swirling flow and effective heat transfer enhancement.
Abstract: Numerical simulations are performed for laminar
continuous and pulsed jets impinging on a surface in order to
investigate the effects of pulsing frequency on the heat transfer
characteristics. The time-averaged Nusselt number of pulsed jets is
larger in the impinging jet region as compared to the continuous jet,
while it is smaller in the outer wall jet region. At the stagnation point,
the mean and RMS Nusselt numbers become larger and smaller,
respectively, as the pulsing frequency increases. Unsteady behaviors
of vortical fluid motions and temperature field are also investigated to
understand the underlying mechanisms of heat transfer enhancement.
Abstract: In the present study, the pressure drop and laminar convection heat transfer characteristics of nanofluids in microchannel heat sink with square duct are numerically investigated. The water based nanofluids created with Al2O3 and CuO particles in four different volume fractions of 0%, 0.5%, 1%, 1.5% and 2% are used to analyze their effects on heat transfer and the pressure drop. Under the laminar, steady-state flow conditions, the finite volume method is used to solve the governing equations of heat transfer. Mixture Model is considered to simulate the nanofluid flow. For verification of used numerical method, the results obtained from numerical calculations were compared with the results in literature for both pure water and the nanofluids in different volume fractions. The distributions of the particles in base fluid are assumed to be uniform. The results are evaluated in terms of Nusselt number, the pressure drop and heat transfer enhancement. Analysis shows that the nanofluids enhance heat transfer while the Reynolds number and the volume fractions are increasing. The best overall enhancement was obtained at φ=%2 and Re=100 for CuO-water nanofluid.
Abstract: Periodic vortex shedding in pulsating flow inside wavy
channel and the effect it has on heat transfer are studied using the
finite volume method. A sinusoidally-varying component is superimposed
on a uniform flow inside a sinusoidal wavy channel and
the effects on the Nusselt number is analyzed. It was found that a
unique optimum value of the pulsation frequency, represented by the
Strouhal number, exists for Reynolds numbers ranging from 125 to
1000. Results suggest that the gain in heat transfer is related to the
process of vortex formation, movement about the troughs of the wavy
channel, and subsequent ejection/destruction through the converging
section. Heat transfer is the highest when the frequencies of the
pulsation and vortex formation approach being in-phase. Analysis of
Strouhal number effect on Nu over a period of pulsation substantiates
the proposed physical mechanism for enhancement. The effect of
changing the amplitude of pulsation is also presented over a period
of pulsation, showing a monotonic increase in heat transfer with
increasing amplitude. The 60% increase in Nusselt number suggests
that sinusoidal fluid pulsation can an effective method for enhancing
heat transfer in laminar, wavy-channel flows.