Abstract: The aim of the current work was to employ the finite
element method to model a slab, with a small hole across its width,
undergoing plastic plane strain deformation. The computational
model had, however, to be validated by comparing its results with
those obtained experimentally. Since they were in good agreement,
the finite element method can therefore be considered a reliable tool
that can help gain better understanding of the mechanism of ductile
failure in structural members having stress raisers. The finite element
software used was ANSYS, and the PLANE183 element was utilized.
It is a higher order 2-D, 8-node or 6-node element with quadratic
displacement behavior. A bilinear stress-strain relationship was used
to define the material properties, with constants similar to those of the
material used in the experimental study. The model was run for
several tensile loads in order to observe the progression of the plastic
deformation region, and the stress concentration factor was
determined in each case. The experimental study involved employing the visioplasticity
technique, where a circular mesh (each circle was 0.5 mm in
diameter, with 0.05 mm line thickness) was initially printed on the
side of an aluminum slab having a small hole across its width.
Tensile loading was then applied to produce a small increment of
plastic deformation. Circles in the plastic region became ellipses,
where the directions of the principal strains and stresses coincided
with the major and minor axes of the ellipses. Next, we were able to
determine the directions of the maximum and minimum shear
stresses at the center of each ellipse, and the slip-line field was then
constructed. We were then able to determine the stress at any point in
the plastic deformation zone, and hence the stress concentration
factor. The experimental results were found to be in good agreement
with the analytical ones.
Abstract: In this paper, analysis of an infinite beam resting on
multilayer tensionless extensible geosynthetic reinforced granular
fill-poor soil system overlying soft soil strata under moving load with
constant velocity is presented. The beam is subjected to a
concentrated load moving with constant velocity. The upper
reinforced granular bed is modeled by a rough membrane embedded
in Pasternak shear layer overlying a series of compressible nonlinear
winkler springs representing the underlying the very poor soil. The
multilayer tensionless extensible geosynthetic layer has been
assumed to deform such that at interface the geosynthetic and the soil
have some deformation. Nonlinear behaviour of granular fill and the
very poor soil has been considered in the analysis by means of
hyperbolic constitutive relationships. Governing differential
equations of the soil foundation system have been obtained and
solved with the help of appropriate boundary conditions. The solution
has been obtained by employing finite difference method by means of
Gauss-Siedal iterative scheme. Detailed parametric study has been
conducted to study the influence of various parameters on the
response of soil–foundation system under consideration by means of
deflection and bending moment in the beam and tension mobilized in
the geosynthetic layer. These parameters include magnitude of
applied load, velocity of load, damping, ultimate resistance of poor
soil and granular fill layer. Range of values of parameters has been
considered as per Indian Railway conditions. This study clearly
observed that the comparisons of multilayer tensionless extensible
geosynthetic reinforcement with poor foundation soil and magnitude
of applied load, relative compressibility of granular fill and ultimate
resistance of poor soil has significant influence on the response of
soil–foundation system.
Abstract: In recent years, fire accidents have been steadily
increased and the amount of property damage caused by the accidents
has gradually raised. Damaging building structure, fire incidents bring
about not only such property damage but also strength degradation and
member deformation. As a result, the building structure undermines its
structural ability. Examining the degradation and the deformation is
very important because reusing the building is more economical than
reconstruction. Therefore, engineers need to investigate the strength
degradation and member deformation well, and make sure that they
apply right rehabilitation methods. This study aims at evaluating
deformation characteristics of fire damaged and rehabilitated normal
strength concrete beams through both experiments and finite element
analyses. For the experiments, control beams, fire damaged beams and
rehabilitated beams are tested to examine deformation characteristics.
Ten test beam specimens with compressive strength of 21MPa are
fabricated and main test variables are selected as cover thickness of
40mm and 50mm and fire exposure time of 1 hour or 2 hours. After
heating, fire damaged beams are air-recurred for 2 months and
rehabilitated beams are repaired with polymeric cement mortar after
being removed the fire damaged concrete cover. All beam specimens
are tested under four points loading. FE analyses are executed to
investigate the effects of main parameters applied to experimental
study. Test results show that both maximum load and stiffness of the
rehabilitated beams are higher than those of the fire damaged beams.
In addition, predicted structural behaviors from the analyses also show
good rehabilitation effect and the predicted load-deflection curves are
similar to the experimental results. For the further, the proposed
analytical method can be used to predict deformation characteristics of
fire damaged and rehabilitated concrete beams without suffering from
time and cost consuming of experimental process.
Abstract: In present global scenario, aluminum alloys are
coining the attention of many innovators as competing structural
materials for automotive and space applications. Comparing to other
challenging alloys, especially, 7xxx series aluminum alloys have
been studied seriously because of benefits such as moderate strength;
better deforming characteristics and affordable cost. It is expected
that substitution of aluminum alloys for steels will result in great
improvements in energy economy, durability and recyclability.
However, it is necessary to improve the strength and the formability
levels at low temperatures in aluminum alloys for still better
applications. Aluminum–Zinc–Magnesium with or without other
wetting agent denoted as 7XXX series alloys are medium strength
heat treatable alloys. In addition to Zn, Mg as major alloying
additions, Cu, Mn and Si are the other solute elements which
contribute for the improvement in mechanical properties by suitable
heat treatment process. Subjecting to suitable treatments like age
hardening or cold deformation assisted heat treatments; known as low
temperature thermomechanical treatments (LTMT) the challenging
properties might be incorporated. T6 is the age hardening or
precipitation hardening process with artificial aging cycle whereas T8
comprises of LTMT treatment aged artificially with X% cold
deformation. When the cold deformation is provided after solution
treatment, there is increase in hardness related properties such as
wear resistance, yield and ultimate strength, toughness with the
expense of ductility. During precipitation hardening both hardness
and strength of the samples are increasing. The hardness value may
further improve when room temperature deformation is positively
supported with age hardening known as thermomechanical treatment.
It is intended to perform heat treatment and evaluate hardness, tensile
strength, wear resistance and distribution pattern of reinforcement in
the matrix. 2 to 2.5 and 3 to 3.5 times increase in hardness is reported
in age hardening and LTMT treatments respectively as compared to
as-cast composite. There was better distribution of reinforcements in
the matrix, nearly two fold increase in strength levels and up to 5
times increase in wear resistance are also observed in the present
study.
Abstract: This paper presents a method of evaluating the effect
of aggregate angularity on hot mix asphalt (HMA) properties and its
relationship to the Permanent Deformation resistance. The research
concluded that aggregate particle angularity had a significant effect
on the Permanent Deformation performance, and also that with an
increase in coarse aggregate angularity there was an increase in the
resistance of mixes to Permanent Deformation. A comparison
between the measured data and predictive data of permanent
deformation predictive models showed the limits of existing
prediction models. The numerical analysis described the permanent
deformation zones and concluded that angularity has an effect of the
onset of these zones. Prediction of permanent deformation help road
agencies and by extension economists and engineers determine the
best approach for maintenance, rehabilitation, and new construction
works of the road infrastructure.
Abstract: The aim of this study is to investigate formability of
Al based closed cell metallic foams at high temperature. The foam
specimens with rectangular section were produced from
AlMg1Si0.6TiH20.8 alloy preform material. Bending and free
bending tests based on gravity effect were applied to foam specimens
at high temperatures. During the tests, the time-angular deformation
relationships with various temperatures were determined.
Deformation types formed in cell walls were investigated by means
of Scanning Electron Microscopy (SEM) and optical microscopy.
Bending deformation about 90° was achieved without any defect at
high temperatures. The importance of a critical temperature and
deformation rate was emphasized in maintaining the deformation.
Significant slip lines on surface of cell walls at tensile zones of
bending specimen were observed. At high strain rates, the microcrack
formation in boundaries of elongated grains was determined.
Abstract: Equal channel angular pressing (ECAP) of
commercial Al-Mg-Si alloy was conducted using two strain rates.
The ECAP processing was conducted at room temperature and at
250°C. Route A was adopted up to a total number of four passes in
the present work. Structural evolution of the aluminum alloy discs
was investigated before and after ECAP processing using optical
microscopy (OM). Following ECAP, simple compression tests and
Vicker’s hardness were performed. OM micrographs showed that, the
average grain size of the as-received Al-Mg-Si disc tends to be larger
than the size of the ECAP processed discs. Moreover, significant
difference in the grain morphologies of the as-received and processed
discs was observed. Intensity of deformation was observed via the
alignment of the Al-Mg-Si consolidated particles (grains) in the
direction of shear, which increased with increasing the number of
passes via ECAP. Increasing the number of passes up to 4 resulted in
increasing the grains aspect ratio up to ~5. It was found that the
pressing temperature has a significant influence on the
microstructure, Hv-values, and compressive strength of the processed
discs. Hardness measurements demonstrated that 1-pass resulted in
increase of Hv-value by 42% compared to that of the as-received
alloy. 4-passes of ECAP processing resulted in additional increase in
the Hv-value. A similar trend was observed for the yield and
compressive strength. Experimental data of the Hv-values
demonstrated that there is a lack of any significant dependence on the
processing strain rate.
Abstract: There are several types of metal-based devices conceived as dampers for the seismic energy absorber whereby damages to the major structural components could be minimized for both new and existing structures. This paper aimed to develop and evaluate structural performance of slit circular shear panel damper for passive seismic energy protection by inelastic deformation. Structural evaluation was done using commercially available nonlinear FE simulation program. The main parameters considered are: diameter-to-thickness (D/t) ratio and slit length-to-width ratio (l/w). Depending on these parameters three different buckling mode and hysteretic behavior was found: yielding prior to buckling without strength degradation, yielding prior to buckling with strength degradation and yielding with buckling and strength degradation which forms pinching at initial displacement. The susceptible location at which the possible crack is initiated is also identified for selected specimens using rupture index.
Abstract: The idea of adding metallic energy dissipaters to a structure to absorb a large part of the seismic energy began four decades ago. There are several types of metal-based devices conceived as dampers for the seismic energy absorber whereby damages to the major structural components could be minimized for both new and existing structures. This paper aimed to develop and evaluate structural performance of both stiffened and non stiffened circular shear panel damper for passive seismic energy protection by inelastic deformation. Structural evaluation was done using commercially available nonlinear FE simulation program. Diameter-to-thickness ratio is employed as main parameter to investigate the hysteresis performance of stiffened and unstiffened circular shear panel. Depending on these parameters three different buckling mode and hysteretic behavior was found: yielding prior to buckling without strength degradation, yielding prior to buckling with strength degradation and yielding with buckling and strength degradation which forms pinching at initial displacement. Hence, the hysteresis behavior is identified, specimens which deform without strength degradation so it will be used as passive energy dissipating device in civil engineering structures.
Abstract: The design of multi stage deep drawing processes requires the evaluation of many process parameters such as the intermediate die geometry, the blank shape, the sheet thickness, the blank holder force, friction, lubrication etc..These process parameters have to be determined for the optimum forming conditions before the process design. In general sheet metal forming may involve stretching drawing or various combinations of these basic modes of deformation. It is important to determine the influence of the process variables in the design of sheet metal working process. Especially, the punch and die corner for deep drawing will affect the formability. At the same time the prediction of sheet metals springback after deep drawing is an important issue to solve for the control of manufacturing processes. Nowadays, the importance of this problem increases because of the use of steel sheeting with high stress and also aluminum alloys.
The aim of this paper is to give a better understanding of the springback and its effect in various sheet metals forming process such as expansion and restreint deep drawing in the cup drawing process, by varying radius die, lubricant for two commercially available materials e.g. galvanized steel and Aluminum sheet. To achieve these goals experiments were carried out and compared with other results. The original of our purpose consist on tests which are ensured by adapting a U-type stretching-bending device on a tensile testing machine, where we studied and quantified the variation of the springback.
Abstract: In this paper analysis of an infinite beam resting on tensionless extensible geosynthetic reinforced granular bed overlying soft soil strata under moving load with constant velocity is presented. The beam is subjected to a concentrated load moving with constant velocity. The upper reinforced granular bed is modeled by a rough elastic membrane embedded in Pasternak shear layer overlying a series of compressible nonlinear Winkler springs representing the under-lied very poor soil. The tensionless extensible geosynthetic layer has been assumed to deform such that at interface the geosynthetic and the soil have some deformation. Nonlinear behavior of granular fill and the very poor soil has been considered in the analysis by means of hyperbolic constitutive relationships. Detailed parametric study has been conducted to study the influence of various parameters on the response of soil foundation system under consideration by means of deflection and bending moment in the beam and tension mobilized in the geosynthetic layer. This study clearly observed that the comparisons of tension and tensionless foundation and magnitude of applied load, relative compressibility of granular fill and ultimate resistance of poor soil has significant influence on the response of soil foundation system.
Abstract: This article aims to investigate the performance of a magnetic fluid based squeeze film between rotating transversely rough curved porous annular plates incorporating the effect of elastic deformation. The associated stochastically averaged Reynolds type equation is solved to obtain the pressure distribution leading to the calculation of the load carrying capacity. The results suggest that the transverse roughness of the bearing surfaces affects the performance adversely although the bearing systems register a relatively improved performance due to the magnetization. The deformation causes reduced the load carrying capacity while the curvature parameters tend to nominally increase the load carrying capacity. Besides, the adverse effect of porosity, deformation and standard deviation can be minimized to some extent by the positive effect of the magnetization and the curvature parameters in the case of negatively skewed roughness by suitably choosing the rotational inertia and the aspect ratio, which becomes significant when negative variance occurs.
Abstract: The objective of this study is to present and to analyze the feasibility of using steel fibers as reinforcement in the cementations matrix to minimize the effect of free shrinkage which is a major cause of cracks that have can observe on concrete structures, also to improve the mechanical resistances of this concrete reinforced. The experimental study was performed on specimens with geometric characteristics adapted to the testing. The tests of shrinkage apply on prismatic specimens, equipped with rods fixed to the ends with different dosages of fibers, it should be noted that the fibers used are hooked end of 50mm length and 67 slenderness. The results show that the compressive strength and flexural strength increases as the degree of incorporation of fibbers increases. And the shrinkage deformations are generally less important for fibers-reinforced concrete to those appearing in the concrete without fibers.
Abstract: There is a growing interest in the use of ultrasonic speckle tracking for biomedical image formation of tissue deformation. Speckle tracking is angle independent and has an ability to differentiate soft tissue into benign and malignant regions. In this paper a simulation model for dynamic ultrasound scatterer is presented. The model composes Field-II ultrasonic scatterers and FEM (ANSYS-11) nodes as a regional tissue deformation. A performance evaluation is presented on axial displacement and strain fields estimation of a uniformly elastic model, using speckle tracking based 1D cross-correlation of optimally segmented pre and post-deformation frames. Optimum correlation window length is investigated in terms of highest signal-to-noise ratio (SNR) for a selected region of interest of a smoothed displacement field. Finally, gradient based strain field of both smoothed and non-smoothed displacement fields are compared. Simulation results from the model are shown to compare favorably with FEM results.
Abstract: The curvature space-time by the presence of material, this deformation must present a pattern of deformation, not random. Space is uniform, elastic and any modification that occurs in one part, causes a change in another.
This deformation exists, must be a constant value and is independent of the observer, and relates the amount of matter, the force caused by the curvature of space and surface space. This unit of space is defined in this study as PIL and represents a constant area of space, deformable in the direction and sense of the center of mass of the body. The PIL is curved and connected to the center of mass of the Earth, to get to that point, through all matter, thus forming part of any place between particles at atomic and subatomic levels. At these levels the space between each particle is flat, unlike the macro where the space curves.
Abstract: Polypropylene blended with natural oil and pigment additives has been studied. Different formulations for each compound were made into polybag used for cultivation of oil palm seedlings for strength and mechanical properties studies. One group of sample was exposed under normal sunlight to initiate degradation and another group of sample was placed under shaded area for five months. All samples were tested for tensile strength to determine the degradation effects. The tensile strength of directly exposed sunlight samples and shaded area showed up to 50% and 25% degradation respectively. However, similar reduction of Young’s modulus for all samples was found for both exposures. Structural investigations were done using FTIR to detect deformation. The natural additives that were used in the studies were all natural and environmental friendly
Abstract: Use of a sliding joint is an effective method to
decrease the stress in foundation structure where there is a horizontal
deformation of subsoil (areas afflicted with underground mining) or
horizontal deformation of a foundation structure (pre-stressed
foundations, creep, shrinkage, temperature deformation). A
convenient material for a sliding joint is a bitumen asphalt belt.
Experiments for different types of bitumen belts were undertaken at
the Faculty of Civil Engineering - VSB Technical University of
Ostrava in 2008. This year an extension of the 2008 experiments is in
progress and the shear resistance of a slide joint is being tested as a
function of temperature in a temperature controlled room. In this
paper experimental results of temperature dependant shear resistance
are presented. The result of the experiments should be the sliding
joint shear resistance as a function of deformation velocity and
temperature. This relationship is used for numerical analysis of
stress/strain relation between foundation structure and subsoil. Using
a rheological slide joint could lead to a decrease of the reinforcement
amount, and contribute to higher reliability of foundation structure
and thus enable design of more durable and sustainable building
structures.
Abstract: Circular knitting machine makes the fabric with more than two knitting tools. Variation of yarn tension between different knitting tools causes different loop length of stitches duration knitting process. In this research, a new intelligent method is applied to control loop length of stitches in various tools based on ideal shape of stitches and real angle of stitches direction while different loop length of stitches causes stitches deformation and deviation those of angle. To measure deviation of stitch direction against variation of tensions, image processing technique was applied to pictures of different fabrics with constant front light. After that, the rate of deformation is translated to needed compensation of loop length cam degree to cure stitches deformation. A fuzzy control algorithm was applied to loop length modification in knitting tools. The presented method was experienced for different knitted fabrics of various structures and yarns. The results show that presented method is useable for control of loop length variation between different knitting tools based on stitch deformation for various knitted fabrics with different fabric structures, densities and yarn types.
Abstract: The results from experimental research of deformation
by upsetting and die forging of lead specimens wit controlled impact
are presented. Laboratory setup for conducting the investigations,
which uses cold rocket engine operated with compressed air, is
described. The results show that when using controlled impact is
achieving greater plastic deformation and consumes less impact
energy than at ordinary impact deformation process.
Abstract: This paper presents the results of thermo-mechanical
characterization of Glass/Epoxy composite specimens using Infrared
Thermography technique. The specimens used for the study were
fabricated in-house with three different lay-up sequences and tested
on a servo hydraulic machine under uni-axial loading. Infrared
Camera was used for on-line monitoring surface temperature changes
of composite specimens during tensile deformation.
Experimental results showed that thermomechanical
characteristics of each type of specimens were distinct. Temperature
was found to be decreasing linearly with increasing tensile stress in
the elastic region due to thermo-elastic effect. Yield point could be
observed by monitoring the change in temperature profile during
tensile testing and this value could be correlated with the results
obtained from stress-strain response. The extent of prior plastic
deformation in the post-yield region influenced the slopes of
temperature response during tensile loading. Partial unloading and
reloading of specimens post-yield results in change in slope in elastic
and plastic regions of composite specimens.