Abstract: With constraints on data availability and for study of power system stability it is adequate to model the synchronous generator with field circuit and one equivalent damper on q-axis known as the model 1.1. This paper presents a systematic procedure for modelling and simulation of a single-machine infinite-bus power system installed with a thyristor controlled series compensator (TCSC) where the synchronous generator is represented by model 1.1, so that impact of TCSC on power system stability can be more reasonably evaluated. The model of the example power system is developed using MATLAB/SIMULINK which can be can be used for teaching the power system stability phenomena, and also for research works especially to develop generator controllers using advanced technologies. Further, the parameters of the TCSC controller are optimized using genetic algorithm. The non-linear simulation results are presented to validate the effectiveness of the proposed approach.
Abstract: In this paper we have proposed a novel dynamic least cost multicast routing protocol using hybrid genetic algorithm for IP networks. Our protocol finds the multicast tree with minimum cost subject to delay, degree, and bandwidth constraints. The proposed protocol has the following features: i. Heuristic local search function has been devised and embedded with normal genetic operation to increase the speed and to get the optimized tree, ii. It is efficient to handle the dynamic situation arises due to either change in the multicast group membership or node / link failure, iii. Two different crossover and mutation probabilities have been used for maintaining the diversity of solution and quick convergence. The simulation results have shown that our proposed protocol generates dynamic multicast tree with lower cost. Results have also shown that the proposed algorithm has better convergence rate, better dynamic request success rate and less execution time than other existing algorithms. Effects of degree and delay constraints have also been analyzed for the multicast tree interns of search success rate.
Abstract: High Speed PM Generators driven by micro-turbines
are widely used in Smart Grid System. So, this paper proposes
comparative study among six classical, optimized and genetic
analytical design cases for 400 kW output power at tip speed 200
m/s. These six design trials of High Speed Permanent Magnet
Synchronous Generators (HSPMSGs) are: Classical Sizing;
Unconstrained optimization for total losses and its minimization;
Constrained optimized total mass with bounded constraints are
introduced in the problem formulation. Then a genetic algorithm is
formulated for obtaining maximum efficiency and minimizing
machine size. In the second genetic problem formulation, we attempt
to obtain minimum mass, the machine sizing that is constrained by
the non-linear constraint function of machine losses. Finally, an
optimum torque per ampere genetic sizing is predicted. All results are
simulated with MATLAB, Optimization Toolbox and its Genetic
Algorithm. Finally, six analytical design examples comparisons are
introduced with study of machines waveforms, THD and rotor losses.
Abstract: This paper presents a formant-tracking linear prediction
(FTLP) model for speech processing in noise. The main focus of this
work is the detection of formant trajectory based on Hidden Markov
Models (HMM), for improved formant estimation in noise. The
approach proposed in this paper provides a systematic framework for
modelling and utilization of a time- sequence of peaks which satisfies
continuity constraints on parameter; the within peaks are modelled
by the LP parameters. The formant tracking LP model estimation
is composed of three stages: (1) a pre-cleaning multi-band spectral
subtraction stage to reduce the effect of residue noise on formants
(2) estimation stage where an initial estimate of the LP model of
speech for each frame is obtained (3) a formant classification using
probability models of formants and Viterbi-decoders. The evaluation
results for the estimation of the formant tracking LP model tested
in Gaussian white noise background, demonstrate that the proposed
combination of the initial noise reduction stage with formant tracking
and LPC variable order analysis, results in a significant reduction in
errors and distortions. The performance was evaluated with noisy
natual vowels extracted from international french and English vocabulary
speech signals at SNR value of 10dB. In each case, the
estimated formants are compared to reference formants.
Abstract: The increasing complexity of software development based on peer to peer networks makes necessary the creation of new frameworks in order to simplify the developer-s task. Additionally, some applications, e.g. fire detection or security alarms may require real-time constraints and the high level definition of these features eases the application development. In this paper, a service model based on a component model with real-time features is proposed. The high-level model will abstract developers from implementation tasks, such as discovery, communication, security or real-time requirements. The model is oriented to deploy services on small mobile devices, such as sensors, mobile phones and PDAs, where the computation is light-weight. Services can be composed among them by means of the port concept to form complex ad-hoc systems and their implementation is carried out using a component language called UM-RTCOM. In order to apply our proposals a fire detection application is described.
Abstract: With Power system movement toward restructuring along with factors such as life environment pollution, problems of transmission expansion and with advancement in construction technology of small generation units, it is expected that small units like wind turbines, fuel cells, photovoltaic, ... that most of the time connect to the distribution networks play a very essential role in electric power industry. With increase in developing usage of small generation units, management of distribution networks should be reviewed. The target of this paper is to present a new method for optimal management of active and reactive power in distribution networks with regard to costs pertaining to various types of dispersed generations, capacitors and cost of electric energy achieved from network. In other words, in this method it-s endeavored to select optimal sources of active and reactive power generation and controlling equipments such as dispersed generations, capacitors, under load tapchanger transformers and substations in a way that firstly costs in relation to them are minimized and secondly technical and physical constraints are regarded. Because the optimal management of distribution networks is an optimization problem with continuous and discrete variables, the new evolutionary method based on Ant Colony Algorithm has been applied. The simulation results of the method tested on two cases containing 23 and 34 buses exist and will be shown at later sections.
Abstract: This paper proposes a new optimization techniques
for the optimization a gas processing plant uncertain feed and
product flows. The problem is first formulated using a continuous
linear deterministic approach. Subsequently, the single and joint
chance constraint models for steady state process with timedependent
uncertainties have been developed. The solution approach
is based on converting the probabilistic problems into their
equivalent deterministic form and solved at different confidence
levels Case study for a real plant operation has been used to
effectively implement the proposed model. The optimization results
indicate that prior decision has to be made for in-operating plant
under uncertain feed and product flows by satisfying all the
constraints at 95% confidence level for single chance constrained and
85% confidence level for joint chance constrained optimizations
cases.
Abstract: This paper describes the shape optimization of impeller
blades for a anti-heeling bidirectional axial flow pump used in ships.
In general, a bidirectional axial pump has an efficiency much lower
than the classical unidirectional pump because of the symmetry of the
blade type. In this paper, by focusing on a pump impeller, the shape of
blades is redesigned to reach a higher efficiency in a bidirectional axial
pump. The commercial code employed in this simulation is CFX v.13.
CFD result of pump torque, head, and hydraulic efficiency was
compared. The orthogonal array (OA) and analysis of variance
(ANOVA) techniques and surrogate model based optimization using
orthogonal polynomial, are employed to determine the main effects
and their optimal design variables. According to the optimal design,
we confirm an effective design variable in impeller blades and explain
the optimal solution, the usefulness for satisfying the constraints of
pump torque and head.
Abstract: This paper presents an optimization technique to economic load dispatch (ELD) problems with considering the daily load patterns and generator constraints using a particle swarm optimization (PSO). The objective is to minimize the fuel cost. The optimization problem is subject to system constraints consisting of power balance and generation output of each units. The application of a constriction factor into PSO is a useful strategy to ensure convergence of the particle swarm algorithm. The proposed method is able to determine, the output power generation for all of the power generation units, so that the total constraint cost function is minimized. The performance of the developed methodology is demonstrated by case studies in test system of fifteen-generation units. The results show that the proposed algorithm scan give the minimum total cost of generation while satisfying all the constraints and benefiting greatly from saving in power loss reduction
Abstract: This paper proposed a nonlinear model predictive
control (MPC) method for the control of gantry crane. One of the main
motivations to apply MPC to control gantry crane is based on its
ability to handle control constraints for multivariable systems. A
pre-compensator is constructed to compensate the input nonlinearity
(nonsymmetric dead zone with saturation) by using its inverse
function. By well tuning the weighting function matrices, the control
system can properly compromise the control between crane position
and swing angle. The proposed control algorithm was implemented for
the control of gantry crane system in System Control Lab of University
of Technology, Sydney (UTS), and achieved desired experimental
results.
Abstract: Data stream analysis is the process of computing
various summaries and derived values from large amounts of data
which are continuously generated at a rapid rate. The nature of a
stream does not allow a revisit on each data element. Furthermore,
data processing must be fast to produce timely analysis results. These
requirements impose constraints on the design of the algorithms to
balance correctness against timely responses. Several techniques
have been proposed over the past few years to address these
challenges. These techniques can be categorized as either dataoriented
or task-oriented. The data-oriented approach analyzes a
subset of data or a smaller transformed representation, whereas taskoriented
scheme solves the problem directly via approximation
techniques. We propose a hybrid approach to tackle the data stream
analysis problem. The data stream has been both statistically
transformed to a smaller size and computationally approximated its
characteristics. We adopt a Monte Carlo method in the approximation
step. The data reduction has been performed horizontally and
vertically through our EMR sampling method. The proposed method
is analyzed by a series of experiments. We apply our algorithm on
clustering and classification tasks to evaluate the utility of our
approach.
Abstract: In the current research, we present an operation framework and protection mechanism to facilitate secure environment to protect mobile agents against tampering. The system depends on the presence of an authentication authority. The advantage of the proposed system is that security measures is an integral part of the design, thus common security retrofitting problems do not arise. This is due to the presence of AlGamal encryption mechanism to protect its confidential content and any collected data by the agent from the visited host . So that eavesdropping on information from the agent is no longer possible to reveal any confidential information. Also the inherent security constraints within the framework allow the system to operate as an intrusion detection system for any mobile agent environment. The mechanism is tested for most of the well known severe attacks against agents and networked systems. The scheme proved a promising performance that makes it very much recommended for the types of transactions that needs highly secure environments, e. g., business to business.
Abstract: The inability to implement the principles of good
corporate governance (GCG) as demonstrated in the surveys is due to
a number of constraints which can be classified into three; namely internal constraints, external constraints, and constraints coming
from the structure of ownership. The issues in the internal constraints
mentioned are related to the function of several elements of the company. As a business organization, corporation is unable to
achieve its goal to successfully implement GCG principles since it is
not support by its internal elements- functions. Two of several numbers of internal elements of a company are ethical work climate
and leadership style of the top management.
To prove the correlation between internal function of organization
(in this case ethical work climate and transformational leadership)
and the successful implementation of GCG principles, this study
proposes two hypotheses to be empirically tested on thirty surveyed organizations; eleven of which are state-owned companies and
nineteen are private companies. These thirty corporations are listed in
the Jakarta Stock Exchange. All state-owned companies in the
samples are those which have been privatized.
The research showed that internal function of organization give
support to the successful implementation of GCG principle. In this
research we can prove that : (i) ethical work climate has positive
significance of correlation with the successful implementation of
social awareness principle (one of principles on GCG) and, (ii) only
at the state-owned companies, transformational leadership have
positive significance effect to forming the ethical work climate.
Abstract: This study considers the problem of determining
operation and maintenance schedules for a containership equipped
with components during its sailing according to a pre-determined
navigation schedule. The operation schedule, which specifies work
time of each component, determines the due-date of each maintenance
activity, and the maintenance schedule specifies the actual start
time of each maintenance activity. The main constraints are component
requirements, workforce availability, working time limitation,
and inter-maintenance time. To represent the problem mathematically,
a mixed integer programming model is developed. Then,
due to the problem complexity, we suggest a heuristic for the objective
of minimizing the sum of earliness and tardiness between the
due-date and the starting time of each maintenance activity. Computational
experiments were done on various test instances and the
results are reported.
Abstract: Along with forward supply chain organization needs
to consider the impact of reverse logistics due to its economic
advantage, social awareness and strict legislations. In this paper, we
develop a system dynamics framework for a closed-loop supply
chain with fuzzy demand and fuzzy collection rate by incorporating
product exchange policy in forward channel and various recovery
options in reverse channel. The uncertainty issues associated with
acquisition and collection of used product have been quantified using
possibility measures. In the simulation study, we analyze order
variation at both retailer and distributor level and compare bullwhip
effects of different logistics participants over time between the
traditional forward supply chain and the closed-loop supply chain.
Our results suggest that the integration of reverse logistics can reduce
order variation and bullwhip effect of a closed-loop system. Finally,
sensitivity analysis is performed to examine the impact of various
parameters on recovery process and bullwhip effect.
Abstract: A new stochastic algorithm called Probabilistic Global Search Johor (PGSJ) has recently been established for global optimization of nonconvex real valued problems on finite dimensional Euclidean space. In this paper we present convergence guarantee for this algorithm in probabilistic sense without imposing any more condition. Then, we jointly utilize this algorithm along with control
parameterization technique for the solution of constrained optimal control problem. The numerical simulations are also included to illustrate the efficiency and effectiveness of the PGSJ algorithm in the solution of control problems.
Abstract: Sustainability in rural production system can only be achieved if it can suitably satisfy the local requirement as well as the outside demand with the changing time. With the increased pressure from the food sector in a globalised world, the agrarian economy
needs to re-organise its cultivable land system to be compatible with new management practices as well as the multiple needs of various stakeholders and the changing resource scenario. An attempt has been made to transform this problem into a multi-objective decisionmaking problem considering various objectives, resource constraints and conditional constraints. An interactive fuzzy multi-objective
programming approach has been used for such a purpose taking a
case study in Indian context to demonstrate the validity of the method.
Abstract: In molecular biology, microarray technology is widely and successfully utilized to efficiently measure gene activity. If working with less studied organisms, methods to design custom-made microarray probes are available. One design criterion is to select probes with minimal melting temperature variances thus ensuring similar hybridization properties. If the microarray application focuses on the investigation of metabolic pathways, it is not necessary to cover the whole genome. It is more efficient to cover each metabolic pathway with a limited number of genes. Firstly, an approach is presented which minimizes the overall melting temperature variance of selected probes for all genes of interest. Secondly, the approach is extended to include the additional constraints of covering all pathways with a limited number of genes while minimizing the overall variance. The new optimization problem is solved by a bottom-up programming approach which reduces the complexity to make it computationally feasible. The new method is exemplary applied for the selection of microarray probes in order to cover all fungal secondary metabolite gene clusters for Aspergillus terreus.
Abstract: The problem of mapping tasks onto a computational grid with the aim to minimize the power consumption and the makespan subject to the constraints of deadlines and architectural requirements is considered in this paper. To solve this problem, we propose a solution from cooperative game theory based on the concept of Nash Bargaining Solution. The proposed game theoretical technique is compared against several traditional techniques. The experimental results show that when the deadline constraints are tight, the proposed technique achieves superior performance and reports competitive performance relative to the optimal solution.
Abstract: In this paper, all variables are supposed to be integer
and positive. In this modern method, objective function is assumed to
be maximized or minimized but constraints are always explained like
less or equal to. In this method, choosing a dual combination of ideal
nonequivalent and omitting one of variables. With continuing this
act, finally, having one nonequivalent with (n-m+1) unknown
quantities in which final nonequivalent, m is counter for constraints,
n is counter for variables of decision.