Abstract: Analytical investigation of the sedimentation
processes in the river engineering and hydraulic structures is of vital
importance as this can affect water supply for the cultivating lands in
the command area. The reason being that gradual sediment formation
behind the reservoir can reduce the nominal capacity of these dams.
The aim of the present paper is to analytically investigate
sedimentation process along the river course and behind the storage
reservoirs in general and the Eastern Intake of the Dez Diversion weir
in particular using the SHARC software. Results of the model
indicated the water level at 115.97m whereas the real time
measurement from the river cross section was 115.98 m which
suggests a significantly close relation between them. The average
transported sediment load in the river was measured at 0.25mm ,
from which it can be concluded that nearly 100% of the suspended
loads in river are moving which suggests no sediment settling but
indicates that almost all sediment loads enters into the intake. It was
further showed the average sediment diameter entering the intake to
be 0.293 mm which in turn suggests that about 85% of suspended
sediments in the river entre the intake. Comparison of the results
from the SHARC model with those obtained form the SSIIM
software suggests quite similar outputs but distinguishing the
SHARC model as more appropriate for the analysis of simpler
problems than other model.
Abstract: This work develops a novel intelligent “model of dynamic decision-making" usingcell assemblies network architecture in robot's movement. The “model of dynamic decision-making" simulates human decision-making, and follows commands to make the correct decisions. The cell assemblies approach consisting of fLIF neurons was used to implement tasks for finding targets and avoiding obstacles. Experimental results show that the cell assemblies approach of can be employed to efficiently complete finding targets and avoiding obstacles tasks and can simulate the human thinking and the mode of information transactions.
Abstract: The great challenge of the agricultural sector is to
produce more crop from less water, which can be achieved by
increasing crop water productivity. The modernization of the
irrigation systems offers a number of possibilities to expand the
economic productivity of water and improve the virtual water status.
The objective of the present study is to assess the global water
productivity (GWP) within the major irrigation command areas of
I.R. Iran. For this purpose, fourteen irrigation command areas where
located in different areas of Iran were selected. In order to calculate
the global water productivity of irrigation command areas, all data on
the delivered water to cropping pattern, cultivated area, crops water
requirement, and yield production rate during 2002-2006 were
gathered. In each of the command areas it seems that the cultivated
crops have a higher amount of virtual water and thus can be replaced
by crops with less virtual water. This is merely suggested due to crop
water consumption and at the time of replacing crops, economic
value as well as cultural and political factors must be considered. The
results indicated that the lowest GWP belongs to Mahyar and
Borkhar irrigation areas, 0.24 kg m-3, and the highest is that of the
Dez irrigation area, 0.81 kg m-3. The findings demonstrated that
water management in the two irrigation areas is just efficient. The
difference in the GWP of irrigation areas is due to variations in the
cropping pattern, amount of crop productions, in addition to the
effective factors in the water use efficiency in the irrigation areas.
Abstract: A glider is in essence an unpowered vehicle and in this project we designed and built an oceanic glider, designed to operate underwater. This Glider was designed to collect ocean data such as temperature, pressure and (in future measures physical dimensions of the operating environment) and output this data to an external source. Development of the Oceanic Glider required research into various actuation systems that control buoyancy, pitch and yaw and the dynamics of these systems. It also involved the design and manufacture of the Glider and the design and implementation of a controller that enabled the Glider to navigate and move in an appropriate manner.
Abstract: Design and modeling of nonlinear systems require the
knowledge of all inside acting parameters and effects. An empirical
alternative is to identify the system-s transfer function from input and
output data as a black box model. This paper presents a procedure
using least squares algorithm for the identification of a feed drive
system coefficients in time domain using a reduced model based on
windowed input and output data. The command and response of the
axis are first measured in the first 4 ms, and then least squares are
applied to predict the transfer function coefficients for this
displacement segment. From the identified coefficients, the next
command response segments are estimated. The obtained results
reveal a considerable potential of least squares method to identify the
system-s time-based coefficients and predict accurately the command
response as compared to measurements.
Abstract: This paper explores the opportunity of using tri-axial
wireless accelerometers for supervised monitoring of sports
movements. A motion analysis system for the upper extremities of
lawn bowlers in particular is developed. Accelerometers are placed
on parts of human body such as the chest to represent the shoulder
movements, the back to capture the trunk motion, back of the hand,
the wrist and one above the elbow, to capture arm movements. These
sensors placement are carefully designed in order to avoid restricting
bowler-s movements. Data is acquired from these sensors in soft-real
time using virtual instrumentation; the acquired data is then
conditioned and converted into required parameters for motion
regeneration. A user interface was also created to facilitate in the
acquisition of data, and broadcasting of commands to the wireless
accelerometers. All motion regeneration in this paper deals with the
motion of the human body segment in the X and Y direction, looking
into the motion of the anterior/ posterior and lateral directions
respectively.