Abstract: Performances analysis of remote sensing sensor is required to pursue a range of scientific research and application objectives. Laboratory analysis of any remote sensing instrument is essential, but not sufficient to establish a valid inflight one. In this study, with the aid of the in situ measurements and corresponding image of three-gray scale permanent artificial target, the in-flight radiometric performances analyses (in-flight radiometric calibration, dynamic range and response linearity, signal-noise-ratio (SNR), radiometric resolution) of self-developed short-wave infrared (SWIR) camera are performed. To acquire the inflight calibration coefficients of the SWIR camera, the at-sensor radiances (Li) for the artificial targets are firstly simulated with in situ measurements (atmosphere parameter and spectral reflectance of the target) and viewing geometries using MODTRAN model. With these radiances and the corresponding digital numbers (DN) in the image, a straight line with a formulation of L = G × DN + B is fitted by a minimization regression method, and the fitted coefficients, G and B, are inflight calibration coefficients. And then the high point (LH) and the low point (LL) of dynamic range can be described as LH= (G × DNH + B) and LL= B, respectively, where DNH is equal to 2n − 1 (n is the quantization number of the payload). Meanwhile, the sensor’s response linearity (δ) is described as the correlation coefficient of the regressed line. The results show that the calibration coefficients (G and B) are 0.0083 W·sr−1m−2µm−1 and −3.5 W·sr−1m−2µm−1; the low point of dynamic range is −3.5 W·sr−1m−2µm−1 and the high point is 30.5 W·sr−1m−2µm−1; the response linearity is approximately 99%. Furthermore, a SNR normalization method is used to assess the sensor’s SNR, and the normalized SNR is about 59.6 when the mean value of radiance is equal to 11.0 W·sr−1m−2µm−1; subsequently, the radiometric resolution is calculated about 0.1845 W•sr-1m-2μm-1. Moreover, in order to validate the result, a comparison of the measured radiance with a radiative-transfer-code-predicted over four portable artificial targets with reflectance of 20%, 30%, 40%, 50% respectively, is performed. It is noted that relative error for the calibration is within 6.6%.
Abstract: Although most digital cameras acquire images in a raw
format, based on a Color Filter Array that arranges RGB color
filters on a square grid of photosensors, most image compression
techniques do not use the raw data; instead, they use the rgb result
of an interpolation algorithm of the raw data. This approach is
inefficient and by performing a lossless compression of the raw data,
followed by pixel interpolation, digital cameras could be more power
efficient and provide images with increased resolution given that the
interpolation step could be shifted to an external processing unit. In
this paper, we conduct a survey on the use of lossless compression
algorithms with raw Bayer images. Moreover, in order to reduce the
effect of the transition between colors that increase the entropy of
the raw Bayer image, we split the image into three new images
corresponding to each channel (red, green and blue) and we study
the same compression algorithms applied to each one individually.
This simple pre-processing stage allows an improvement of more than
15% in predictive based methods.
Abstract: This paper discusses a corner detection algorithm
for camera calibration. Calibration is a necessary step in many
computer vision and image processing applications. Robust
corner detection for an image of a checkerboard is required
to determine intrinsic and extrinsic parameters. In this paper,
an algorithm for fully automatic and robust X-corner detection
is presented. Checkerboard corner points are automatically
found in each image without user interaction or any prior
information regarding the number of rows or columns. The
approach represents each X-corner with a quadratic fitting
function. Using the fact that the X-corners are saddle points,
the coefficients in the fitting function are used to identify each
corner location. The automation of this process greatly simplifies
calibration. Our method is robust against noise and different
camera orientations. Experimental analysis shows the accuracy
of our method using actual images acquired at different camera
locations and orientations.
Abstract: In this paper, a design of H.263 based wireless video
transceiver is presented for wireless camera system. It uses standard
WIFI transceiver and the covering area is up to 100m. Furthermore the
standard H.263 video encoding technique is used for video
compression since wireless video transmitter is unable to transmit high
capacity raw data in real time and the implemented system is capable
of streaming at speed of less than 1Mbps using NTSC 720x480 video.
Abstract: In this paper, propose method that can user’s position
that based on database is built from single camera. Previous
positioning calculate distance by arrival-time of signal like GPS
(Global Positioning System), RF(Radio Frequency). However, these
previous method have weakness because these have large error range
according to signal interference. Method for solution estimate position
by camera sensor. But, signal camera is difficult to obtain relative
position data and stereo camera is difficult to provide real-time
position data because of a lot of image data, too. First of all, in this
research we build image database at space that able to provide
positioning service with single camera. Next, we judge similarity
through image matching of database image and transmission image
from user. Finally, we decide position of user through position of most
similar database image. For verification of propose method, we
experiment at real-environment like indoor and outdoor. Propose
method is wide positioning range and this method can verify not only
position of user but also direction.
Abstract: Introduction: Student nurses must develop skills in observation, communication and reflection as well as public health knowledge from their first year of training. This paper will explain a method developed for students to collect their own findings about public health in urban areas. These areas are both rich in the history of old public health that informs the content of many traditional public health walks, but are also locations where new public health concerns about chronic disease are concentrated. The learning method explained in this paper enables students to collect their own data and write original work as first year students. Examples of their findings will be given. Methodology: In small groups, health care students are instructed to walk in neighbourhoods near to the hospitals they will soon attend as apprentice nurses. On their walks, they wander slowly, engage in conversations, and enter places open to the public. As they drift, they observe with all five senses in the real three dimensional world to collect data for their reflective accounts of old and new public health. They are encouraged to stop for refreshments and taste, as well as look, hear, smell, and touch while on their walk. They reflect as a group and later develop an individual reflective account in which they write up their deep reflections about what they observed on their walk. In preparation for their walk, they are encouraged to look at studies of quality of Life and other neighbourhood statistics as well as undertaking a risk assessment for their walk. Findings: Reflecting on their walks, students apply theoretical concepts around social determinants of health and health inequalities to develop their understanding of communities in the neighbourhoods visited. They write about the treasured historical architecture made of stone, bronze and marble which have outlived those who built them; but also how the streets are used now. The students develop their observations into thematic analyses such as: what we drink as illustrated by the empty coke can tossed into a now disused drinking fountain; the shift in home-life balance illustrated by streets where families once lived over the shop which are now walked by commuters weaving around each other as they talk on their mobile phones; and security on the street, with CCTV cameras placed at regular intervals, signs warning trespasses and barbed wire; but little evidence of local people watching the street. Conclusion: In evaluations of their first year, students have reported the health walk as one of their best experiences. The innovative approach was commended by the UK governing body of nurse education and it received a quality award from the nurse education funding body. This approach to education allows students to develop skills in the real world and write original work.
Abstract: Due to the higher power loss levels in electronic components, the thermal design of PCBs (Printed Circuit Boards) of an assembled device becomes one of the most important quality factors in electronics. Nonetheless, some of leading causes of the microelectronic component failures are due to higher temperatures, the leakages or thermal-mechanical stress, which is a concern, is the reliability of microelectronic packages. This article presents an experimental approach to measure the junction temperature of exposed pad packages. The implemented solution is in a prototype phase, using a temperature-sensitive parameter (TSP) to measure temperature directly on the die, validating the numeric results provided by the Mechanical APDL (Ansys Parametric Design Language) under same conditions. The physical device-under-test is composed by a Thermal Test Chip (TTC-1002) and assembly in a QFN cavity, soldered to a test-board according to JEDEC Standards. Monitoring the voltage drop across a forward-biased diode, is an indirectly method but accurate to obtain the junction temperature of QFN component with an applied power range between 0,3W to 1.5W. The temperature distributions on the PCB test-board and QFN cavity surface were monitored by an infra-red thermal camera (Goby-384) controlled and images processed by the Xeneth software. The article provides a set-up to monitorize in real-time the junction temperature of ICs, namely devices with the exposed pad package (i.e. QFN). Presenting the PCB layout parameters that the designer should use to improve thermal performance, and evaluate the impact of voids in solder interface in the device junction temperature.
Abstract: In the recent years, a fundamental revolution in the Mobile Phone technology from just being able to provide voice and short message services to becoming the most essential part of our lives by connecting to network and various app stores for downloading software apps of almost every activity related to our life from finding location to banking from getting news updates to downloading HD videos and so on. This progress in Smart Phone industry has modernized and transformed our way of living into a trouble-free world. The smart phone has become our personal computers with the addition of significant features such as multi core processors, multi-tasking, large storage space, bluetooth, WiFi, including large screen and cameras. With this evolution, the rise in the security threats have also been amplified. In Literature, different threats related to smart phones have been highlighted and various precautions and solutions have been proposed to keep the smart phone safe which carries all the private data of a user. In this paper, a survey has been carried out to find out the most secure and the most unsecure smart phone operating system among the most popular smart phones in use today.
Abstract: Younger and younger children are now using a smartphone, a device which has become ‘a must have’ and the life of children would be almost ‘unthinkable’ without one. Devices are becoming lighter and lighter but offering an array of options and applications as well as the unavoidable access to the Internet, without which it would be almost unusable. Numerous features such as taking of photographs, listening to music, information search on the Internet, access to social networks, usage of some of the chatting and messaging services, are only some of the numerous features offered by ‘smart’ devices. They have replaced the alarm clock, home phone, camera, tablet and other devices. Their use and possession have become a part of the everyday image of young people. Apart from the positive aspects, the use of smartphones has also some downsides. For instance, free time was usually spent in nature, playing, doing sports or other activities enabling children an adequate psychophysiological growth and development. The greater usage of smartphones during classes to check statuses on social networks, message your friends, play online games, are just some of the possible negative aspects of their application. Considering that the age of the population using smartphones is decreasing and that smartphones are no longer ‘foreign’ to children of pre-school age (smartphones are used at home or in coffee shops or shopping centers while waiting for their parents, playing video games often inappropriate to their age), particular attention must be paid to a very sensitive group, the teenagers who almost never separate from their ‘pets’. This paper is divided into two sections, theoretical and empirical ones. The theoretical section gives an overview of the pros and cons of the usage of smartphones, while the empirical section presents the results of a research conducted in three elementary schools regarding the usage of smartphones and, specifically, their usage during classes, during breaks and to search information on the Internet, check status updates and 'likes’ on the Facebook social network.
Abstract: In this paper we presented a new method for tracking
flying targets in color video sequences based on contour and kernel.
The aim of this work is to overcome the problem of losing target in
changing light, large displacement, changing speed, and occlusion.
The proposed method is made in three steps, estimate the target
location by particle filter, segmentation target region using neural
network and find the exact contours by greedy snake algorithm. In
the proposed method we have used both region and contour
information to create target candidate model and this model is
dynamically updated during tracking. To avoid the accumulation of
errors when updating, target region given to a perceptron neural
network to separate the target from background. Then its output used
for exact calculation of size and center of the target. Also it is used as
the initial contour for the greedy snake algorithm to find the exact
target's edge. The proposed algorithm has been tested on a database
which contains a lot of challenges such as high speed and agility of
aircrafts, background clutter, occlusions, camera movement, and so
on. The experimental results show that the use of neural network
increases the accuracy of tracking and segmentation.
Abstract: In many practical situations, bubbles are dispersed in a
liquid phase. Understanding these complex bubbly flows is therefore
a key issue for applications such as shell and tube heat exchangers,
mineral flotation and oxidation in water treatment. Although a large
body of work exists for bubbles rising in an unbounded medium,
that of bubbles rising in constricted geometries has received less
attention. The particular case of a bubble sliding underneath an
inclined surface is common to two-phase flow systems. The current
study intends to expand this knowledge by performing experiments
to quantify the streamwise flow structures associated with a single
sliding air bubble under an inclined surface in quiescent water. This
is achieved by means of two-dimensional, two-component particle
image velocimetry (PIV), performed with a continuous wave laser
and high-speed camera. PIV vorticity fields obtained in a plane
perpendicular to the sliding surface show that there is significant bulk
fluid motion away from the surface. The associated momentum of the
bubble means that this wake motion persists for a significant time
before viscous dissipation. The magnitude and direction of the flow
structures in the streamwise measurement plane are found to depend
on the point on its path through which the bubble enters the plane.
This entry point, represented by a phase angle, affects the nature and
strength of the vortical structures. This study reconstructs the vorticity
field in the wake of the bubble, converting the field at different
instances in time to slices of a large-scale wake structure. This is, in
essence, Taylor’s ”frozen turbulence” hypothesis. Applying this to the
vorticity fields provides a pseudo three-dimensional representation
from 2-D data, allowing for a more intuitive understanding of the
bubble wake. This study provides insights into the complex dynamics
of a situation common to many engineering applications, particularly
shell and tube heat exchangers in the nucleate boiling regime.
Abstract: To increase the temperature contrast in thermal
images, the characteristics of the electrical conductivity and thermal
imaging modalities can be combined. In this experimental study, it is
objected to observe whether the temperature contrast created by the
tumor tissue can be improved just due to the current application
within medical safety limits. Various thermal breast phantoms are
developed to simulate the female breast tissue. In vitro experiments
are implemented using a thermal infrared camera in a controlled
manner. Since experiments are implemented in vitro, there is no
metabolic heat generation and blood perfusion. Only the effects and
results of the electrical stimulation are investigated. Experimental
study is implemented with two-dimensional models. Temperature
contrasts due to the tumor tissues are obtained. Cancerous tissue is
determined using the difference and ratio of healthy and tumor
images. 1 cm diameter single tumor tissue causes almost 40 °mC
temperature contrast on the thermal-breast phantom. Electrode
artifacts are reduced by taking the difference and ratio of background
(healthy) and tumor images. Ratio of healthy and tumor images show
that temperature contrast is increased by the current application.
Abstract: This paper outlines the development of an
experimental technique in quantifying supersonic jet flows, in an
attempt to avoid seeding particle problems frequently associated with
particle-image velocimetry (PIV) techniques at high Mach numbers.
Based on optical flow algorithms, the idea behind the technique
involves using high speed cameras to capture Schlieren images of the
supersonic jet shear layers, before they are subjected to an adapted
optical flow algorithm based on the Horn-Schnuck method to
determine the associated flow fields. The proposed method is capable
of offering full-field unsteady flow information with potentially
higher accuracy and resolution than existing point-measurements or
PIV techniques. Preliminary study via numerical simulations of a
circular de Laval jet nozzle successfully reveals flow and shock
structures typically associated with supersonic jet flows, which serve
as useful data for subsequent validation of the optical flow based
experimental results. For experimental technique, a Z-type Schlieren
setup is proposed with supersonic jet operated in cold mode,
stagnation pressure of 4 bar and exit Mach of 1.5. High-speed singleframe
or double-frame cameras are used to capture successive
Schlieren images. As implementation of optical flow technique to
supersonic flows remains rare, the current focus revolves around
methodology validation through synthetic images. The results of
validation test offers valuable insight into how the optical flow
algorithm can be further improved to improve robustness and
accuracy. Despite these challenges however, this supersonic flow
measurement technique may potentially offer a simpler way to
identify and quantify the fine spatial structures within the shock shear
layer.
Abstract: The purposes of hydraulic gate are to maintain the
functions of storing and draining water. It bears long-term hydraulic
pressure and earthquake force and is very important for reservoir and
waterpower plant. The high tensile strength of steel plate is used as
constructional material of hydraulic gate. The cracks and rusts,
induced by the defects of material, bad construction and seismic
excitation and under water respectively, thus, the mechanics
phenomena of gate with crack are probing into the cause of stress
concentration, induced high crack increase rate, affect the safety and
usage of hydroelectric power plant. Stress distribution analysis is a
very important and essential surveying technique to analyze
bi-material and singular point problems. The finite difference
infinitely small element method has been demonstrated, suitable for
analyzing the buckling phenomena of welding seam and steel plate
with crack. Especially, this method can easily analyze the singularity
of kink crack. Nevertheless, the construction form and deformation
shape of some gates are three-dimensional system. Therefore, the
three-dimensional Digital Image Correlation (DIC) has been
developed and applied to analyze the strain variation of steel plate with
crack at weld joint. The proposed Digital image correlation (DIC)
technique is an only non-contact method for measuring the variation of
test object. According to rapid development of digital camera, the cost
of this digital image correlation technique has been reduced.
Otherwise, this DIC method provides with the advantages of widely
practical application of indoor test and field test without the restriction
on the size of test object. Thus, the research purpose of this research is
to develop and apply this technique to monitor mechanics crack
variations of weld steel hydraulic gate and its conformation under
action of loading. The imagines can be picked from real time
monitoring process to analyze the strain change of each loading stage.
The proposed 3-Dimensional digital image correlation method,
developed in the study, is applied to analyze the post-buckling
phenomenon and buckling tendency of welded steel plate with crack.
Then, the stress intensity of 3-dimensional analysis of different
materials and enhanced materials in steel plate has been analyzed in
this paper. The test results show that this proposed three-dimensional
DIC method can precisely detect the crack variation of welded steel
plate under different loading stages. Especially, this proposed DIC
method can detect and identify the crack position and the other flaws
of the welded steel plate that the traditional test methods hardly detect
these kind phenomena. Therefore, this proposed three-dimensional
DIC method can apply to observe the mechanics phenomena of
composite materials subjected to loading and operating.
Abstract: This paper focuses on the orbit avoidance strategy of
the optical remote sensing satellite. The optical remote sensing
satellite, moving along the Sun-synchronous orbit, is equipped with
laser warning equipment to alert CCD camera from laser attacks. This
paper explores the strategy of satellite avoidance to protect the CCD
camera and also the satellite. The satellite could evasive to several
target points in the orbital coordinates of virtual satellite. The so-called
virtual satellite is a passive vehicle which superposes the satellite at the
initial stage of avoidance. The target points share the consistent cycle
time and the same semi-major axis with the virtual satellite, which
ensures the properties of the satellite’s Sun-synchronous orbit remain
unchanged. Moreover, to further strengthen the avoidance capability
of satellite, it can perform multi-target-points avoid maneuvers. On
occasions of fulfilling the satellite orbit tasks, the orbit can be restored
back to virtual satellite through orbit maneuvers. There into, the avoid
maneuvers adopts pulse guidance. In addition, the fuel consumption is
optimized. The avoidance strategy discussed in this article is
applicable to optical remote sensing satellite when it is encountered
with hostile attack of space-based laser anti-satellite.
Abstract: This paper presents the design and implementation
details of a complete unmanned aerial system (UAS) based
on commercial-off-the-shelf (COTS) components, focusing on
safety, security, search and rescue scenarios in GPS-denied
environments. In particular, The aerial platform is capable
of semi-autonomously navigating through extremely low-light,
GPS-denied indoor environments based on onboard sensors only,
including a downward-facing optical flow camera. Besides, an
additional low-cost payload camera system is developed to stream
both infra-red video and visible light video to a ground station in
real-time, for the purpose of detecting sign of life and hidden humans.
The total cost of the complete system is estimated to be $1150,
and the effectiveness of the system has been tested and validated
in practical scenarios.
Abstract: Digital cameras to reduce cost, use an image sensor to
capture color images. Color Filter Array (CFA) in digital cameras
permits only one of the three primary (red-green-blue) colors to be
sensed in a pixel and interpolates the two missing components
through a method named demosaicking. Captured data is interpolated
into a full color image and compressed in applications. Color
interpolation before compression leads to data redundancy. This
paper proposes a new Vector Quantization (VQ) technique to
construct a VQ codebook with Differential Evolution (DE)
Algorithm. The new technique is compared to conventional Linde-
Buzo-Gray (LBG) method.
Abstract: One of the tasks of optical surveillance is to detect
anomalies in large amounts of image data. However, if the size of the
anomaly is very small, limited information is available to distinguish
it from the surrounding environment. Spectral detection provides a
useful source of additional information and may help to detect
anomalies with a size of a few pixels or less. Unfortunately, spectral
cameras are expensive because of the difficulty of separating two
spatial in addition to one spectral dimension. We investigate the
possibility of modifying a simple spectral line detector for outdoor
detection. This may be especially useful if the area of interest forms a
line, such as the horizon. We use a monochrome CCD that also
enables detection into the near infrared. A simple camera is attached
to the setup to determine which part of the environment is spectrally
imaged. Our preliminary results indicate that sensitive detection of
very small targets is indeed possible. Spectra could be taken from the
various targets by averaging columns in the line image. By imaging a
set of lines of various widths we found narrow lines that could not be
seen in the color image but remained visible in the spectral line
image. A simultaneous analysis of the entire spectra can produce
better results than visual inspection of the line spectral image. We are
presently developing calibration targets for spatial and spectral
focusing and alignment with the spatial camera. This will present
improved results and more use in outdoor application.
Abstract: This paper presents the influences on the entrainment
of serpentines by grinding and reagents during copper–nickel sulfide
flotation. The previous bench flotation tests were performed to extract
the metallic values from the ore in Yunnan Mine, China and the
relatively satisfied results with recoveries of 86.92% Cu, 54.92% Ni,
and 74.73% Pt+Pd in the concentrate were harvested at their grades of
4.02%, 3.24% and 76.61 g/t, respectively. However, the content of
MgO in the concentrate was still more than 19%. Micro-flotation tests
were conducted with the objective of figuring out the influences on the
entrainment of serpentines into the concentrate by particle size,
flocculants or depressants and collectors, as well as visual
observations in suspension by OLYMPUS camera. All the tests results
pointed to the presences of both “entrapped-in” serpentines and its
coating on the hydrophobic flocs resulted from strong collectors
(combination of butyl xanthate, butyl ammonium dithophosphate,
even after adding carboxymethyl cellulose as effective depressant.
And fine grinding may escalate the entrainment of serpentines in the
concentrate.
Abstract: In this paper, we present a four-step ortho-rectification
procedure for real-time geo-referencing of video data from a low-cost
UAV equipped with a multi-sensor system. The basic procedures for
the real-time ortho-rectification are: (1) decompilation of the video
stream into individual frames; (2) establishing the interior camera
orientation parameters; (3) determining the relative orientation
parameters for each video frame with respect to each other; (4)
finding the absolute orientation parameters, using a self-calibration
bundle and adjustment with the aid of a mathematical model. Each
ortho-rectified video frame is then mosaicked together to produce a
mosaic image of the test area, which is then merged with a well
referenced existing digital map for the purpose of geo-referencing
and aerial surveillance. A test field located in Abuja, Nigeria was
used to evaluate our method. Video and telemetry data were collected
for about fifteen minutes, and they were processed using the four-step
ortho-rectification procedure. The results demonstrated that the
geometric measurement of the control field from ortho-images is
more accurate when compared with those from original perspective
images when used to pin point the exact location of targets on the
video imagery acquired by the UAV. The 2-D planimetric accuracy
when compared with the 6 control points measured by a GPS receiver
is between 3 to 5 metres.