Abstract: This paper proposes a low-cost reconfigurable
architecture for AES algorithm. The proposed architecture separates
SubBytes and MixColumns into two parallel data path, and supports
different bit-width operation for this two data path. As a result, different number of S-box can be supported in this architecture. The
throughput and power consumption can be adjusted by changing the
number of S-box running in this design. Using the TSMC 0.18μm CMOS standard cell library, a very low-cost implementation of 7K
Gates is obtained under 182MHz frequency. The maximum throughput is 360Mbps while using 4 S-Box simultaneously, and the
minimum throughput is 114Mbps while only using 1 S-Box
Abstract: Since prestressed concrete members rely on the tensile
strength of the prestressing strands to resist loads, loss of even few
them could result catastrophic. Therefore, it is important to measure
present residual prestress force. Although there are some techniques
for obtaining present prestress force, some problems still remain. One
method is to install load cell in front of anchor head but this may
increase cost. Load cell is a transducer using the elastic material
property. Anchor head is also an elastic material and this might result
in monitoring monitor present prestress force. Features of fiber optic
sensor such as small size, great sensitivity, high durability can assign
sensing function to anchor head. This paper presents the concept of
smart anchor head which acts as load cell and experiment for the
applicability of it. Test results showed the smart anchor head worked
good and strong linear relationship between load and response.
Abstract: This paper presents Cost per Equivalent Wafer Out, which we find useful in wafer fab operational cost monitoring and controlling. It removes the loading and product mix effect in the cost variance analysis. The operation heads, therefore, could immediately focus on identifying areas for cost improvement. Without this, they would have to measure the impact of the loading variance and product mix variance between actual and budgeted prior to make any decision on cost improvement. Cost per Equivalent Wafer Out, thereby, increases efficiency in wafer fab operational cost monitoring and controlling.
Abstract: According as the Architecture, Engineering and Construction (AEC) Industry projects have grown more complex and larger, the number of utilization of BIM for 3D design and simulation is increasing significantly. Therefore, typical applications of BIM such as clash detection and alternative measures based on 3-dimenstional planning are expanded to process management, cost and quantity management, structural analysis, check for regulation, and various domains for virtual design and construction. Presently, commercial BIM software is operated on single-user environment, so initial cost is so high and the investment may be wasted frequently. Cloud computing that is a next-generation internet technology enables simple internet devices (such as PC, Tablet, Smart phone etc) to use services and resources of BIM software. In this paper, we suggested developing method of the BIM software based on cloud computing environment in order to expand utilization of BIM and reduce cost of BIM software. First, for the benchmarking, we surveyed successful case of BIM and cloud computing. And we analyzed needs and opportunities of BIM and cloud computing in AEC Industry. Finally, we suggested main functions of BIM software based on cloud computing environment and developed a simple prototype of cloud computing BIM software for basic BIM model viewing.
Abstract: In today-s global and competitive market,
manufacturing companies are working hard towards improving their
production system performance. Most companies develop production
systems that can help in cost reduction. Manufacturing systems
consist of different elements including production methods,
machines, processes, control and information systems. Human issues
are an important part of manufacturing systems, yet most companies
do not pay sufficient attention to them. In this paper, a workforce
planning (WP) model is presented. A non-linear programming model
is developed in order to minimize the hiring, firing, training and
overtime costs. The purpose is to determine the number of workers
for each worker type, the number of workers trained, and the number
of overtime hours. Moreover, a decision support system (DSS) based
on the proposed model is introduced using the Excel-Lingo software
interfacing feature. This model will help to improve the interaction
between the workers, managers and the technical systems in
manufacturing.
Abstract: In today-s turbulent environment, companies are faced with two principal challenges. On the one hand, it is necessary to produce ever more cost-effectively to remain competitive. On the other hand, factories need to be transformable in order to manage unpredictable changes in the corporate environment. To deal with these different challenges, companies use the philosophy of lean production in the first case, in the second case the philosophy of transformability. To a certain extent these two approaches follow different directions. This can cause conflicts when designing factories. Therefore, the Institute of Production Systems and Logistics (IFA) of the Leibniz University of Hanover has developed a procedure to allow companies to evaluate and design their factories with respect to the requirements of both philosophies.
Abstract: Reciprocating compressors are flexible to handle wide capacity and condition swings, offer a very efficient method of compressing almost any gas mixture in wide range of pressure, can generate high head independent of density, and have numerous applications and wide power ratings. These make them vital component in various units of industrial plants. In this paper optimum reciprocating compressor configuration regarding interstage pressures, low suction pressure, non-lubricated cylinder, speed of machine, capacity control system, compressor valve, lubrication system, piston rod coating, cylinder liner material, barring device, pressure drops, rod load, pin reversal, discharge temperature, cylinder coolant system, performance, flow, coupling, special tools, condition monitoring (including vibration, thermal and rod drop monitoring), commercial points, delivery and acoustic conditions are presented.
Abstract: This study aims to propose three evaluation methods to
evaluate the Tokyo Cap and Trade Program when emissions trading is
performed virtually among enterprises, focusing on carbon dioxide
(CO2), which is the only emitted greenhouse gas that tends to increase.
The first method clarifies the optimum reduction rate for the highest
cost benefit, the second discusses emissions trading among enterprises
through market trading, and the third verifies long-term emissions
trading during the term of the plan (2010-2019), checking the validity
of emissions trading partly using Geographic Information Systems
(GIS). The findings of this study can be summarized in the following
three points.
1. Since the total cost benefit is the greatest at a 44% reduction rate, it
is possible to set it more highly than that of the Tokyo Cap and
Trade Program to get more total cost benefit.
2. At a 44% reduction rate, among 320 enterprises, 8 purchasing
enterprises and 245 sales enterprises gain profits from emissions
trading, and 67 enterprises perform voluntary reduction without
conducting emissions trading. Therefore, to further promote
emissions trading, it is necessary to increase the sales volumes of
emissions trading in addition to sales enterprises by increasing the
number of purchasing enterprises.
3. Compared to short-term emissions trading, there are few enterprises
which benefit in each year through the long-term emissions trading
of the Tokyo Cap and Trade Program. Only 81 enterprises at the
most can gain profits from emissions trading in FY 2019. Therefore,
by setting the reduction rate more highly, it is necessary to increase
the number of enterprises that participate in emissions trading and
benefit from the restraint of CO2 emissions.
Abstract: Information on weed distribution within the field is necessary to implement spatially variable herbicide application. Since hand labor is costly, an automated weed control system could be feasible. This paper deals with the development of an algorithm for real time specific weed recognition system based on Histogram Maxima with threshold of an image that is used for the weed classification. This algorithm is specifically developed to classify images into broad and narrow class for real-time selective herbicide application. The developed system has been tested on weeds in the lab, which have shown that the system to be very effectiveness in weed identification. Further the results show a very reliable performance on images of weeds taken under varying field conditions. The analysis of the results shows over 95 percent classification accuracy over 140 sample images (broad and narrow) with 70 samples from each category of weeds.
Abstract: In this article, by using fuzzy AHP and TOPSIS
technique we propose a new method for project selection problem.
After reviewing four common methods of comparing alternatives
investment (net present value, rate of return, benefit cost analysis
and payback period) we use them as criteria in AHP tree. In this
methodology by utilizing improved Analytical Hierarchy Process
by Fuzzy set theory, first we try to calculate weight of each
criterion. Then by implementing TOPSIS algorithm, assessment of
projects has been done. Obtained results have been tested in a
numerical example.
Abstract: The present study has been carried out with a view to calculate the coastal vulnerability index (CVI) to know the high and low sensitive areas and area of inundation due to future SLR. Both conventional and remotely sensed data were used and analyzed through the modelling technique. Out of the total study area, 8.26% is very high risk, 14.21% high, 9.36% medium, 22.46% low and 7.35% in the very low vulnerable category, due to costal components. Results of the inundation analysis indicate that 225.2 km² and 397 km² of the land area will be submerged by flooding at 1m and 10m inundation levels. The most severely affected sectors are expected to be the residential, industrial and recreational areas. As this coast is planned for future coastal developmental activities, measures such as industrializations, building regulation, urban growth planning and agriculture, development of an integrated coastal zone management, strict enforcement of the Coastal Regulation Zone (CRZ) Act, monitoring of impacts and further research in this regard are recommended for the study area.
Abstract: The oil and gas industry has moved towards Load and
Resistance Factor Design through API RP2A - LRFD and the
recently published international standard, ISO-19902, for design of
fixed steel offshore structures. The ISO 19902 is intended to provide
a harmonized design practice that offers a balanced structural fitness
for the purpose, economy and safety. As part of an ongoing work, the
reliability analysis of tubular joints of the jacket structure has been
carried out to calibrate the load and resistance factors for the design
of offshore platforms in Malaysia, as proposed in the ISO.
Probabilistic models have been established for the load effects (wave,
wind and current) and the tubular joints strengths. In this study the
First Order Reliability Method (FORM), coded in MATLAB
Software has been employed to evaluate the reliability index of the
typical joints, designed using API RP2A - WSD and ISO 19902.
Abstract: Artificial Neural Network (ANN) has been
extensively used for classification of heart sounds for its
discriminative training ability and easy implementation. However, it
suffers from overparameterization if the number of nodes is not
chosen properly. In such cases, when the dataset has redundancy
within it, ANN is trained along with this redundant information that
results in poor validation. Also a larger network means more
computational expense resulting more hardware and time related
cost. Therefore, an optimum design of neural network is needed
towards real-time detection of pathological patterns, if any from heart
sound signal. The aims of this work are to (i) select a set of input
features that are effective for identification of heart sound signals and
(ii) make certain optimum selection of nodes in the hidden layer for a
more effective ANN structure. Here, we present an optimization
technique that involves Singular Value Decomposition (SVD) and
QR factorization with column pivoting (QRcp) methodology to
optimize empirically chosen over-parameterized ANN structure.
Input nodes present in ANN structure is optimized by SVD followed
by QRcp while only SVD is required to prune undesirable hidden
nodes. The result is presented for classifying 12 common
pathological cases and normal heart sound.
Abstract: The conceptually construction of axially chiral indolostilbenesi.eN-(2-{(E)-2-[2'-(1-Acetyl-1H-indol-2-yl)-3'chloro-4,4',6,6'-tetramethoxy[1,1'-biphenyl]-2yl]ethenyl}phenyl)acetamide and N-(2-{(E)-2-[2'-(1-Acetyl-1H-indol-2-yl)-3'-chloro-2,4',6,6'-tetramethoxy[1,1'-biphenyl]-4-yl]ethenyl}phenyl) acetamide are described in this paper. These structure, were obtained by the tactical combination of palladium-catalyzed coupling which produced 10-acetamido-3,5-dimethoxystilbene, follow by FeCl3-induced oxidative cyclization/dimerisation. All structures were unambiguously confirmed by 1D (1H, 13C) and 2D NMR experiment, (COSY, HMQC, HMBC) and mass spectrometry.
Abstract: Selection of a project among a set of possible
alternatives is a difficult task that the decision maker (DM) has to
face. In this paper, by using a fuzzy TOPSIS technique we propose a
new method for a project selection problem. After reviewing four
common methods of comparing investment alternatives (net present
value, rate of return, benefit cost analysis and payback period) we
use them as criteria in a TOPSIS technique. First we calculate the
weight of each criterion by a pairwise comparison and then we utilize
the improved TOPSIS assessment for the project selection.
Abstract: In the past decade, because of wide applications of
hybrid systems, many researchers have considered modeling and
control of these systems. Since switching systems constitute an
important class of hybrid systems, in this paper a method for optimal
control of linear switching systems is described. The method is also
applied on the two-tank system which is a much appropriate system
to analyze different modeling and control techniques of hybrid
systems. Simulation results show that, in this method, the goals of
control and also problem constraints can be satisfied by an
appropriate selection of cost function.