Abstract: Reciprocating compressors are flexible to handle wide capacity and condition swings, offer a very efficient method of compressing almost any gas mixture in wide range of pressure, can generate high head independent of density, and have numerous applications and wide power ratings. These make them vital component in various units of industrial plants. In this paper optimum reciprocating compressor configuration regarding interstage pressures, low suction pressure, non-lubricated cylinder, speed of machine, capacity control system, compressor valve, lubrication system, piston rod coating, cylinder liner material, barring device, pressure drops, rod load, pin reversal, discharge temperature, cylinder coolant system, performance, flow, coupling, special tools, condition monitoring (including vibration, thermal and rod drop monitoring), commercial points, delivery and acoustic conditions are presented.
Abstract: This study aims to propose three evaluation methods to
evaluate the Tokyo Cap and Trade Program when emissions trading is
performed virtually among enterprises, focusing on carbon dioxide
(CO2), which is the only emitted greenhouse gas that tends to increase.
The first method clarifies the optimum reduction rate for the highest
cost benefit, the second discusses emissions trading among enterprises
through market trading, and the third verifies long-term emissions
trading during the term of the plan (2010-2019), checking the validity
of emissions trading partly using Geographic Information Systems
(GIS). The findings of this study can be summarized in the following
three points.
1. Since the total cost benefit is the greatest at a 44% reduction rate, it
is possible to set it more highly than that of the Tokyo Cap and
Trade Program to get more total cost benefit.
2. At a 44% reduction rate, among 320 enterprises, 8 purchasing
enterprises and 245 sales enterprises gain profits from emissions
trading, and 67 enterprises perform voluntary reduction without
conducting emissions trading. Therefore, to further promote
emissions trading, it is necessary to increase the sales volumes of
emissions trading in addition to sales enterprises by increasing the
number of purchasing enterprises.
3. Compared to short-term emissions trading, there are few enterprises
which benefit in each year through the long-term emissions trading
of the Tokyo Cap and Trade Program. Only 81 enterprises at the
most can gain profits from emissions trading in FY 2019. Therefore,
by setting the reduction rate more highly, it is necessary to increase
the number of enterprises that participate in emissions trading and
benefit from the restraint of CO2 emissions.
Abstract: Since the world printing industry has to confront
globalization with a constant change, the Thai printing industry, as a
small but increasingly significant part of the world printing industry,
cannot inevitably escape but has to encounter with the similar change
and also the need to revamp its production processes, designs and
technology to make them more appealing to both international and
domestic market. The essential question is what is the Thai
competitive edge in the printing industry in changing environment?
This research is aimed to study the Thai level of competitive edge in
terms of marketing, technology, environment friendly, and the level
of satisfaction of the process of using printing machines. To access
the extent to which is the trends in competitiveness of Thai printing
industry, both quantitative and qualitative study were conducted. The
quantitative analysis was restricted to 100 respondents. The
qualitative analysis was restricted to a focus group of 10 individuals
from various backgrounds in the Thai printing industry. The findings
from the quantitative analysis revealed that the overall mean scores
are 4.53, 4.10, and 3.50 for the competitiveness of marketing, the
competitiveness of technology, and the competitiveness of being
environment friendly respectively. However, the level of satisfaction
for the process of using machines has a mean score only 3.20. The
findings from the qualitative analysis have revealed that target
customers have increasingly reordered due to their contentment in
both low prices and the acceptable quality of the products. Moreover,
the Thai printing industry has a tendency to convert to ambient green
technology which is friendly to the environment. The Thai printing
industry is choosing to produce or substitute with products that are
less damaging to the environment. It is also found that the Thai
printing industry has been transformed into a very competitive
industry which bargaining power rests on consumers who have a
variety of choices.
Abstract: This research is a comparative study of complexity, as a multidimensional concept, in the context of streetscape composition in Algeria and Japan. 80 streetscapes visual arrays have been collected and then presented to 20 participants, with different cultural backgrounds, in order to be categorized and classified according to their degrees of complexity. Three analysis methods have been used in this research: cluster analysis, ranking method and Hayashi Quantification method (Method III). The results showed that complexity, disorder, irregularity and disorganization are often conflicting concepts in the urban context. Algerian daytime streetscapes seem to be balanced, ordered and regular, and Japanese daytime streetscapes seem to be unbalanced, regular and vivid. Variety, richness and irregularity with some aspects of order and organization seem to characterize Algerian night streetscapes. Japanese night streetscapes seem to be more related to balance, regularity, order and organization with some aspects of confusion and ambiguity. Complexity characterized mainly Algerian avenues with green infrastructure. Therefore, for Japanese participants, Japanese traditional night streetscapes were complex. And for foreigners, Algerian and Japanese avenues nightscapes were the most complex visual arrays.
Abstract: A new digital transceiver circuit for asynchronous frame detection is proposed where both the transmitter and receiver contain all digital components, thereby avoiding possible use of conventional devices like monostable multivibrators with unstable external components such as resistances and capacitances. The proposed receiver circuit, in particular, uses a combinational logic block yielding an output which changes its state as soon as the start bit of a new frame is detected. This, in turn, helps in generating an efficient receiver sampling clock. A data latching circuit is also used in the receiver to latch the recovered data bits in any new frame. The proposed receiver structure is also extended from 4- bit information to any general n data bits within a frame with a common expression for the output of the combinational logic block. Performance of the proposed hardware design is evaluated in terms of time delay, reliability and robustness in comparison with the standard schemes using monostable multivibrators. It is observed from hardware implementation that the proposed circuit achieves almost 33 percent speed up over any conventional circuit.
Abstract: Glaucoma diagnosis involves extracting three features
of the fundus image; optic cup, optic disc and vernacular. Present
manual diagnosis is expensive, tedious and time consuming. A
number of researches have been conducted to automate this process.
However, the variability between the diagnostic capability of an
automated system and ophthalmologist has yet to be established. This
paper discusses the efficiency and variability between
ophthalmologist opinion and digital technique; threshold. The
efficiency and variability measures are based on image quality
grading; poor, satisfactory or good. The images are separated into
four channels; gray, red, green and blue. A scientific investigation
was conducted on three ophthalmologists who graded the images
based on the image quality. The images are threshold using multithresholding
and graded as done by the ophthalmologist. A
comparison of grade from the ophthalmologist and threshold is made.
The results show there is a small variability between result of
ophthalmologists and digital threshold.
Abstract: This paper proposes a feed-forward control in a halfbridge
resonant dc link inverter. The configuration of feed-forward
control is based on synchronous sigma-delta modulation and the halfbridge
resonant dc link inverter consists of two inductors, one
capacitor and two power switches. The simulation results show the
proposed technique can reject non-ideal dc bus improving the total
harmonic distortion.
Abstract: The development of competences and practical
capacities of students is getting an important incidence into the
guidelines of the European Higher Education Area (EHEA). The
methodology applied in this work is based on the education through
directed resolution of practical cases. All cases are related to
professional tasks that the students will have to develop in their
future career. The method is intended to form the necessary
competences of students of the Marine Engineering and Maritime
Transport Degree in the matter of “Physics".
The experience was applied in the course of 2011/2012. Students
were grouped, and a practical task was assigned to them, that should
be developed and solved within the team. The aim was to realize
students learning by three ways: their own knowledge, the
contribution of their teammates and the teacher's direction. The
results of the evaluation were compared with those obtained
previously by the traditional teaching method.
Abstract: Cloud Computing (CC) has become one of the most
talked about emerging technologies that provides powerful
computing and large storage environments through the use of the
Internet. Cloud computing provides different dynamically scalable
computing resources as a service. It brings economic benefits to
individuals and businesses that adopt the technology. In theory
adoption of cloud computing reduces capital and operational
expenditure on information technology. For this to be a reality there
is need to solve some challenges and at the same time addressing
concerns that consumers have about cloud computing. This paper
looks at Cloud Computing in general then highlights the challenges
of Cloud Computing and finally suggests solutions to some of the
challenges.
Abstract: Capacity and efficiency of any refrigerating system
diminish rapidly as the difference between the evaporating and
condensing temperature is increased by a reduction in the evaporator
temperature. The single stage vapour compression refrigeration
system using various refrigerants are limited to an evaporator
temperature of -40 0C. Below temperature of -40 0C the either
cascade refrigeration system or multi stage vapour compression
system is employed. Present work describes thermal design of
condenser (HTS), cascade condenser and evaporator (LTS) of
R404A-R508B and R410A-R23 cascade refrigeration system. Heat
transfer area of condenser, cascade condenser and evaporator for
both systems are compared and the effect of condenser and
evaporator temperature on heat-transfer area for both systems is
studied under same operating condition. The results shows that the
required heat-transfer area of condenser and cascade condenser for
R410A-R23 cascade system is lower than the R404A-R508B cascade
system but heat transfer area of evaporator is similar for both the
system. The heat transfer area of condenser and cascade condenser
decreases with increase in condenser temperature (Tc), whereas the
heat transfer area of cascade condenser and evaporator increases with
increase in evaporator temperature (Te).