Abstract: In this paper, the problem of reducing switching
activity in on-chip buses at the stage of high-level synthesis is
considered, and a high-level low power bus binding based on dynamic
bit reordering is proposed. Whereas conventional methods use a fixed
bit ordering between variables within a bus, the proposed method
switches a bit ordering dynamically to obtain a switching activity
reduction. As a result, the proposed method finds a binding solution
with a smaller value of total switching activity (TSA). Experimental
result shows that the proposed method obtains a binding solution
having 12.0-34.9% smaller TSA compared with the conventional
methods.
Abstract: The pavement constructions on soft and expansive soils are not durable and unable to sustain heavy traffic loading. As a result, pavement failures and settlement problems will occur very often even under light traffic loading due to cyclic and rolling effects. Geotechnical engineers have dwelled deeply into this matter, and adopt various methods to improve the engineering characteristics of soft fine-grained soils and expansive soils. The problematic soils are either replaced by good and better quality material or treated by using chemical stabilization with various binding materials. Increased the strength and durability are also the part of the sustainability drive to reduce the environment footprint of the built environment by the efficient use of resources and waste recycle materials. This paper presents a series of laboratory tests and evaluates the effect of cement and fly ash on the strength and drainage characteristics of soil in Miri. The tests were performed at different percentages of cement and fly ash by dry weight of soil. Additional tests were also performed on soils treated with the combinations of fly ash with cement and lime. The results of this study indicate an increase in unconfined compression strength and a decrease in hydraulic conductivity of the treated soil.
Abstract: Bones are dynamic and responsive organs, they
regulate their strength and mass according to the loads which they are subjected. Because, the Wnt/β-catenin pathway has profound
effects on the regulation of bone mass, we hypothesized that mechanical loading of bone cells stimulates Wnt/β-catenin signaling, which results in the generation of new bone mass.
Mechanical loading triggers the secretion of the Wnt molecule, which after binding to transmembrane proteins, causes GSK-3β (Glycogen synthase kinase 3 beta) to cease the phosphorylation of β-catenin. β-catenin accumulation in the cytoplasm, followed by its
transport into the nucleus, binding to transcription factors (TCF/LEF)
that initiate transcription of genes related to bone formation. To test this hypothesis, we used TOPGAL (Tcf Optimal Promoter
β-galactosidase) mice in an experiment in which cyclic loads were
applied to the forearm. TOPGAL mice are reporters for cells effected
by the Wnt/β-catenin signaling pathway. TOPGAL mice are genetically engineered mice in which transcriptional activation of β-
catenin, results in the production of an enzyme, β-galactosidase. The
presence of this enzyme allows us to localize transcriptional
activation of β-catenin to individual cells, thereby, allowing us to quantify the effects that mechanical loading has on the Wnt/β-catenin pathway and new bone formation. The ulnae of loaded TOPGAL
mice were excised and transverse slices along different parts of the
ulnar shaft were assayed for the presence of β-galactosidase.
Our results indicate that loading increases β-catenin transcriptional
activity in regions where this pathway is already primed (i.e. where basal activity is already higher) in a load magnitude dependent
manner. Further experiments are needed to determine the temporal and spatial activation of this signaling in relation to bone formation.
Abstract: A new chelating resin is prepared by coupling Amberlite XAD-4 with 1-amino-2-naphthole through an azo spacer. The resulting sorbent has been characterized by FT-IR, elemental analysis and thermogravimetric analysis (TGA) and studied for preconcentrating of Fe (II) using flame atomic absorption spectrometry (FAAS) for metal monitoring. The optimum pH value for sorption of the iron ions was 6.5. The resin was subjected to evaluation through batch binding of mentioned metal ion. Quantitative desorption occurs instantaneously with 0.5 M HNO3. The sorption capacity was found 4.1 mmol.g-1 of resin for Fe (II) in the aqueous solution. The chelating resin can be reused for 10 cycles of sorption-desorption without any significant change in sorption capacity. A recovery of 97% was obtained the metal ions with 0.5 M HNO3 as eluting agent. The method was applied for metal ions determination from industrial waste water sample.