Abstract: An automated fibre placement method has been
developed to build through-thickness reinforcement into carbon fibre
reinforced plastic laminates during their production, with the goal
of increasing delamination fracture toughness while circumventing
the additional costs and defects imposed by post-layup stitching
and z-pinning. Termed ‘inter-weaving’, the method uses custom
placement sequences of thermoset prepreg tows to distribute regular
fibre link regions in traditionally clean ply interfaces. Inter-weaving’s impact on mode I delamination fracture toughness
was evaluated experimentally through double cantilever beam tests
(ASTM standard D5528-13) on [±15°]9 laminates made from Park
Electrochemical Corp. E-752-LT 1/4” carbon fibre prepreg tape.
Unwoven and inter-woven automated fibre placement samples were
compared to those of traditional laminates produced from standard
uni-directional plies of the same material system. Unwoven automated fibre placement laminates were found to
suffer a mostly constant 3.5% decrease in mode I delamination
fracture toughness compared to flat uni-directional plies. Inter-weaving caused significant local fracture toughness increases
(up to 50%), though these were offset by a matching overall
reduction. These positive and negative behaviours of inter-woven
laminates were respectively found to be caused by fibre breakage
and matrix deformation at inter-weave sites, and the 3D layering
of inter-woven ply interfaces providing numerous paths of least
resistance for crack propagation.
Abstract: Gas release from the pipelines is one of the main factors in the gas industry accidents. Released gas ejects from the pipeline as a free jet and in the growth process, the fuel gets mixed with the ambient air. Accordingly, an accidental spark will release the chemical energy of the mixture with an explosion. Gas explosion damages the equipment and endangers the life of staffs. So due to importance of safety in gas industries, prevision of accident can reduce the number of the casualties. In this paper, natural gas leakages from the low pressure pipelines are studied in two steps: 1) the simulation of mixing process and identification of flammable zones and 2) the simulation of wind effects on the mixing process. The numerical simulations were performed by using the finite volume method and the pressure-based algorithm. Also, for the grid generation the structured method was used. The results show that, in just 6.4 s after accident, released natural gas could penetrate to 40 m in vertical and 20 m in horizontal direction. Moreover, the results show that the wind speed is a key factor in dispersion process. In fact, the wind transports the flammable zones into the downstream. Hence, to improve the safety of the people and human property, it is preferable to construct gas facilities and buildings in the opposite side of prevailing wind direction.
Abstract: Energy transmission pipelines are one of the most vital parts of each country which several strict laws have been conducted to enhance the safety of these lines and their vicinity. One of these laws is the safety distance around high pressure gas pipelines. Safety distance refers to the minimum distance from the pipeline where people and equipment do not confront with serious damages. In the present study, safety distance around high pressure gas transmission pipelines were determined by using numerical methods. For this purpose, gas leakages from cracked pipeline and created jet fires were simulated as continuous ignition, three dimensional, unsteady and turbulent cases. Numerical simulations were based on finite volume method and turbulence of flow was considered using k-ω SST model. Also, the combustion of natural gas and air mixture was applied using the eddy dissipation method. The results show that, due to the high pressure difference between pipeline and environment, flow chocks in the cracked area and velocity of the exhausted gas reaches to sound speed. Also, analysis of the incident radiation results shows that safety distances around 42 inches high pressure natural gas pipeline based on 5 and 15 kW/m2 criteria are 205 and 272 meters, respectively.
Abstract: This paper copes with the numerical simulation for convective heat transfer in the stator disk of an axial flux permanent magnet (AFPM) electrical machine. Overheating is one of the main issues in the design of AFMPs, which mainly occurs in the stator disk, so that it needs to be prevented. A rotor-stator configuration with 16 magnets at the periphery of the rotor is considered. Air is allowed to flow through openings in the rotor disk and channels being formed between the magnets and in the gap region between the magnets and the stator surface. The rotating channels between the magnets act as a driving force for the air flow. The significant non-dimensional parameters are the rotational Reynolds number, the gap size ratio, the magnet thickness ratio, and the magnet angle ratio. The goal is to find correlations for the Nusselt number on the stator disk according to these non-dimensional numbers. Therefore, CFD simulations have been performed with the multiple reference frame (MRF) technique to model the rotary motion of the rotor and the flow around and inside the machine. A minimization method is introduced by a pattern-search algorithm to find the appropriate values of the reference temperature. It is found that the correlations are fast, robust and is capable of predicting the stator heat transfer with a good accuracy. The results reveal that the magnet angle ratio diminishes the stator heat transfer, whereas the rotational Reynolds number and the magnet thickness ratio improve the convective heat transfer. On the other hand, there a certain gap size ratio at which the stator heat transfer reaches a maximum.
Abstract: In this paper, we presented a highly sensitive immune-affinity monolithic array for detection of α-fetoprotein (AFP) and carcinoembryonic antigen (CEA). Firstly, the epoxy functionalized monolith arrays were fabricated using UV initiated copolymerization method. Scanning electron microscopy (SEM) image showed that the poly(BABEA-co-GMA) monolith exhibited a well-controlled skeletal and well-distributed porous structure. Then, AFP and CEA immune-affinity monolithic arrays were prepared by immobilization of AFP and CEA antibodies on epoxy functionalized monolith arrays. With a non-competitive immune response format, the presented AFP and CEA immune-affinity arrays were demonstrated as an inexpensive, flexible, homogeneous and stable array for detection of AFP and CEA.
Abstract: In this paper, the steady-state temperature of a sample 500 KW two rotor one stator Non-slotted axial flux permanent magnet motor is calculated using the finite element simulator software package. Due to the high temperature in various parts of the machine, especially at stator winding, a cooling system is designed for the motor and the temperature is recalculated. The results show that the temperature obtained for the parts is within the permissible range.
Abstract: Axial Flux Permanent Magnet (AFPM) Machines require effective cooling due to their high power density. The detrimental effects of overheating such as degradation of the insulation materials, magnets demagnetization, and increase of Joule losses are well known. This paper describes the CFD simulations performed on a test rig model of an air cooled Axial Flux Permanent Magnet (AFPM) generator built at Durham University to identify the temperatures and heat transfer coefficient on the stator. The Reynolds Averaged Navier-Stokes and the Energy equations are solved and the flow pattern and heat transfer developing inside the machine are described. The Nusselt number on the stator surfaces has been found. The dependency of the heat transfer on the flow field is described temperature field obtained. Tests on an experimental are undergoing in order to validate the CFD results.
Abstract: Alpfa-fetoprotein and its fragments may be an important vehicle for targeted delivery of radionuclides to the tumor. We investigated the effect of conditions on the labeling of biologically active synthetic peptide based on the (F-afp) with technetium-99m. The influence of the nature of the buffer solution, pH, concentration of reductant, concentration of the peptide and the reaction temperature on the yield of labeling was examined. As a result, the following optimal conditions for labeling of (F-afp) are found: pH 8.5 (phosphate and bicarbonate buffers) and pH from 1.7 to 7.0 (citrate buffer). The reaction proceeds with sufficient yield at room temperature for 30 min at the concentration of SnCl2 and (Fafp) (F-afp) is to be less than 10 mkg/ml and 25 mkg/ml, respectively. Investigations of the test drug accumulation in the tumor cells of human breast cancer were carried out. Results can be assumed that the in vivo study of the (F-afp) in experimental tumor lesions will show concentrations sufficient for imaging these lesions by SPECT.
Abstract: The evaluation of unit cell neutronic parameters and
lifetime for some innovant reactors without on sit-refuling will be
held in this work. the behavior of some small and medium reactors
without on site refueling with triso and cermet fuel. For the FBNR
long life except we propose to change the enrichment of the Cermet
MFE to 9%. For the AFPR reactor we can see that the use of the
Cermet MFE can extend the life of this reactor but to maintain the
same life period for AFPR-SC we most use burnup poison to have the
same slope for Kinf (Burnup). PFPWR50 cell behaves almost in
same way using both fuels Cermet and TRISO. So we can conclude
that PFPWR50 reactor, with CERMET Fuel, is kept among the long
cycle reactors and with the new configuration we avoid subcriticality
at the beginning of cycle. The evaluation of unit cell neutronic
parameters reveals a good agreement with the goal of BWR-PB
concept. It is found out that the Triso fuel assembly lifetime can be
extended for a reasonably long period without being refueled,
approximately up to 48GWd/t burnup. Using coated particles fuels
with the Cermet composition can be more extended the fuel assembly
life time, approximately 52 GWd/t.
Abstract: Energy and exergy study of air-water combined solar collector which is called dual purpose solar collector (DPSC) is investigated. The method of ε - NTU is used. Analysis is performed for triangle channels. Parameters like the air flow rate and water inlet temperature are studied. Results are shown that DPSC has better energy and exergy efficiency than single collector. In addition, the triangle passage with water inlet temperature of 60O C has shown better exergy and energy efficiency.
Abstract: This paper presents the development of a hybrid
thermal model for the EVO Electric AFM 140 Axial Flux Permanent
Magnet (AFPM) machine as used in hybrid and electric vehicles. The
adopted approach is based on a hybrid lumped parameter and finite
difference method. The proposed method divides each motor
component into regular elements which are connected together in a
thermal resistance network representing all the physical connections
in all three dimensions. The element shape and size are chosen
according to the component geometry to ensure consistency. The
fluid domain is lumped into one region with averaged heat transfer
parameters connecting it to the solid domain. Some model parameters
are obtained from Computation Fluid Dynamic (CFD) simulation and
empirical data. The hybrid thermal model is described by a set of
coupled linear first order differential equations which is discretised
and solved iteratively to obtain the temperature profile. The
computation involved is low and thus the model is suitable for
transient temperature predictions. The maximum error in temperature
prediction is 3.4% and the mean error is consistently lower than the
mean error due to uncertainty in measurements. The details of the
model development, temperature predictions and suggestions for
design improvements are presented in this paper.
Abstract: Ethanol is generally used as a therapeutic reagent against Hepatocellular carcinoma (HCC or hepatoma) worldwide, as it can induce Hepatocellular carcinoma cell apoptosis at low concentration through a multifactorial process regulated by several unknown proteins. This paper provides a simple and available proteomic strategy for exploring differentially expressed proteins in the apoptotic pathway. The appropriate concentrations of ethanol required to induce HepG2 cell apoptosis were first assessed by MTT assay, Gisma and fluorescence staining. Next, the central proteins involved in the apoptosis pathway processs were determined using 2D-PAGE, SDS-PAGE, and bio-software analysis. Finally the downregulation of two proteins, AFP and survivin, were determined by immunocytochemistry and reverse transcriptase PCR (RT-PCR) technology. The simple, useful method demonstrated here provides a new approach to proteomic analysis in key bio-regulating process including proliferation, differentiation, apoptosis, immunity and metastasis.
Abstract: Identifying the nature of protein-nanoparticle
interactions and favored binding sites is an important issue in
functional characterization of biomolecules and their physiological
responses. Herein, interaction of silver nanoparticles with lysozyme
as a model protein has been monitored via fluorescence spectroscopy.
Formation of complex between the biomolecule and silver
nanoparticles (AgNPs) induced a steady state reduction in the
fluorescence intensity of protein at different concentrations of
nanoparticles. Tryptophan fluorescence quenching spectra suggested
that silver nanoparticles act as a foreign quencher, approaching the
protein via this residue. Analysis of the Stern-Volmer plot showed
quenching constant of 3.73 μM−1. Moreover, a single binding site in
lysozyme is suggested to play role during interaction with AgNPs,
having low affinity of binding compared to gold nanoparticles.
Unfolding studies of lysozyme showed that complex of lysozyme-
AgNPs has not undergone structural perturbations compared to the
bare protein. Results of this effort will pave the way for utilization of
sensitive spectroscopic techniques for rational design of
nanobiomaterials in biomedical applications.
Abstract: Wheat gluten hydrolyzates (WGHs) and anchovy fine
powder hydrolyzates (AFPHs) were produced at 300 MPa using
combinations of Flavourzyme 500MG (F), Alcalase 2.4L (A),
Marugoto E (M) and Protamex (P), and then were compared to those
produced at ambient pressure concerning the contents of soluble solid
(SS), soluble nitrogen and electrophoretic profiles. The contents of SS
in the WGHs and AFPHs increased up to 87.2% according to the
increase in enzyme number both at high and ambient pressure. Based
on SS content, the optimum enzyme combinations for one-, two-,
three- and four-enzyme hydrolysis were determined as F, FA, FAM
and FAMP, respectively. Similar trends were found for the contents of
total soluble nitrogen (TSN) and TCA-soluble nitrogen (TCASN). The
contents of SS, TSN and TCASN in the hydrolyzates together with
electrophoretic mobility maps indicates that the high-pressure
treatment of this study accelerated protein hydrolysis compared to
ambient-pressure treatment.
Abstract: Mycophenolic acid “MPA" is a secondary metabolite
of Penicillium bervicompactum with antibiotic and
immunosuppressive properties. In this study, fermentation process
was established for production of mycophenolic acid by Penicillium
bervicompactum MUCL 19011 in shake flask. The maximum MPA
production, product yield and productivity were 1.379 g/L, 18.6 mg/g
glucose and 4.9 mg/L.h respectively. Glucose consumption, biomass
and MPA production profiles were investigated during fermentation
time. It was found that MPA production starts approximately after
180 hours and reaches to a maximum at 280 h. In the next step, the
effects of methionine and acetate concentrations on MPA production
were evaluated. Maximum MPA production, product yield and
productivity (1.763 g/L, 23.8 mg/g glucose and 6.30 mg/L. h
respectively) were obtained with using 2.5 g/L methionine in culture
medium. Further addition of methionine had not more positive effect
on MPA production. Finally, results showed that the addition of
acetate to the culture medium had not any observable effect on MPA
production
Abstract: Mycophenolic acid “MPA" is a secondary metabolite
of Penicillium bervicompactum with antibiotic and
immunosuppressive properties. In this study, fermentation process
was established for production of mycophenolic acid by Penicillium
bervicompactum MUCL 19011 in shake flask. The maximum MPA
production, product yield and productivity were 1.379 g/L, 18.6 mg/g
glucose and 4.9 mg/L.h respectively. Glucose consumption, biomass
and MPA production profiles were investigated during fermentation
time. It was found that MPA production starts approximately after
180 hours and reaches to a maximum at 280 h. In the next step, the
effects of methionine and acetate concentrations on MPA production
were evaluated. Maximum MPA production, product yield and
productivity (1.763 g/L, 23.8 mg/g glucose and 6.30 mg/L. h
respectively) were obtained with using 2.5 g/L methionine in culture
medium. Further addition of methionine had not more positive effect
on MPA production. Finally, results showed that the addition of
acetate to the culture medium had not any observable effect on MPA
production.
Abstract: The objective of this paper is to analyze the
performance of a double-sided axial flux permanent magnet
brushless DC (AFPM BLDC) motor with two-phase winding.
To study the motor operation, a mathematical dynamic model
has been proposed for motor, which became the basis for
simulations that were performed using MATLAB/SIMULINK
software package. The results of simulations were presented
in form of the waveforms of selected quantities and the
electromechanical characteristics performed by the motor. The
calculation results show that the two-phase motor version
develops smooth torque and reaches high efficiency. The twophase
motor can be applied where more smooth torque is
required. Finally a study on the influence of switching angle
on motor performance shows that when advance switching
technique is used, the motor operates with the highest
efficiency.
Abstract: In this paper presented initial design of Low Speed
Axial Flux Permanent Magnet (AFPM) Machine with Non-Slotted
TORUS topology type by use of certain algorithm (Appendix).
Validation of design algorithm studied by means of selected data of
an initial prototype machine. Analytically design calculation carried
out by means of design algorithm and obtained results compared with
results of Finite Element Method (FEM).
Abstract: This paper presents the optimal design and development
of an axial flux motor for blood pump application. With the design
objective of maximizing the motor efficiency and torque, different
topologies of AFPM machine has been examined. Selection of
optimal magnet fraction, Halbach arrangement of rotor magnets and
the use of Soft Magnetic Composite (SMC) material for the stator
core results in a novel motor with improved efficiency and torque
profile. The results of the 3D Finite element analysis for the novel
motor have been shown.