Abstract: In turning hardened steel, polycrystalline cubic boron
nitride (cBN) compacts are widely used, due to their higher hardness
and higher thermal conductivity. However, in milling hardened steel,
fracture of cBN cutting tools readily occurs because they have poor
fracture toughness. Therefore, coated cemented carbide tools, which
have good fracture toughness and wear resistance, are generally
widely used. In this study, hardened steel (ASTM D2, JIS SKD11,
60HRC) was milled with three physical vapor deposition
(PVD)-coated cemented carbide end mill cutters in order to determine
effective tool materials for cutting hardened steel at high cutting
speeds. The coating films used were (Ti,W)N/(Ti,W,Si)N and
(Ti,W)N/(Ti,W,Si,Al)N coating films. (Ti,W,Si,Al)N is a new type of
coating film. The inner layer of the (Ti,W)N/(Ti,W,Si)N and
(Ti,W)N/(Ti,W,Si,Al)N coating system is (Ti,W)N coating film, and
the outer layer is (Ti,W,Si)N and (Ti,W,Si,Al)N coating films,
respectively. Furthermore, commercial (Ti,Al)N-based coating film
was also used. The following results were obtained: (1) In milling
hardened steel at a cutting speed of 3.33 m/s, the tool wear width of the
(Ti,W)N/(Ti,W,Si,Al)N-coated tool was smaller than that of the
(Ti,W)N/(Ti,W,Si)N-coated tool. And, compared with the commercial
(Ti,Al)N, the tool wear width of the (Ti,W)N/(Ti,W,Si,Al)N-coated
tool was smaller than that of the (Ti,Al)N-coated tool. (2) The tool
wear of the (Ti,W)N/(Ti,W,Si,Al)N-coated tool increased with an
increase in cutting speed. (3) The (Ti,W)N/(Ti,W,Si,Al)N-coated
cemented carbide was an effective tool material for high-speed cutting
below a cutting speed of 3.33 m/s.
Abstract: The term hybrid composite refers to the composite
containing more than one type of fiber material as reinforcing fillers.
It has become attractive structural material due to the ability of
providing better combination of properties with respect to single fiber
containing composite. The eco-friendly nature as well as processing
advantage, light weight and low cost have enhanced the attraction
and interest of natural fiber reinforced composite. The objective of
present research is to study the mechanical properties of jute-coir
fiber reinforced hybrid polypropylene (PP) composite according to
filler loading variation. In the present work composites were
manufactured by using hot press machine at four levels of fiber
loading (5, 10, 15 and 20 wt %). Jute and coir fibers were utilized at a
ratio of (1:1) during composite manufacturing. Tensile, flexural,
impact and hardness tests were conducted for mechanical
characterization. Tensile test of composite showed a decreasing trend
of tensile strength and increasing trend of the Young-s modulus with
increasing fiber content. During flexural, impact and hardness tests,
the flexural strength, flexural modulus, impact strength and hardness
were found to be increased with increasing fiber loading. Based on
the fiber loading used in this study, 20% fiber reinforced composite
resulted the best set of mechanical properties.
Abstract: The conjugate gradient optimization algorithm
usually used for nonlinear least squares is presented and is
combined with the modified back propagation algorithm yielding
a new fast training multilayer perceptron (MLP) algorithm
(CGFR/AG). The approaches presented in the paper consist of
three steps: (1) Modification on standard back propagation
algorithm by introducing gain variation term of the activation
function, (2) Calculating the gradient descent on error with
respect to the weights and gains values and (3) the determination
of the new search direction by exploiting the information
calculated by gradient descent in step (2) as well as the previous
search direction. The proposed method improved the training
efficiency of back propagation algorithm by adaptively modifying
the initial search direction. Performance of the proposed method
is demonstrated by comparing to the conjugate gradient algorithm
from neural network toolbox for the chosen benchmark. The
results show that the number of iterations required by the
proposed method to converge is less than 20% of what is required
by the standard conjugate gradient and neural network toolbox
algorithm.
Abstract: In this research, the diabetes conditions of people (healthy, prediabete and diabete) were tried to be identified with noninvasive palm perspiration measurements. Data clusters gathered from 200 subjects were used (1.Individual Attributes Cluster and 2. Palm Perspiration Attributes Cluster). To decrase the dimensions of these data clusters, Principal Component Analysis Method was used. Data clusters, prepared in that way, were classified with Support Vector Machines. Classifications with highest success were 82% for Glucose parameters and 84% for HbA1c parametres.
Abstract: KREISIG is a computer simulation program, firstly developed by Munawar (1994) in Germany to optimize signalized roundabout. The traffic movement is based on the car following theory. Turbine method has been implemented for signal setting. The program has then been further developed in Indonesia to meet the traffic characteristics in Indonesia by adjusting the sensitivity of the drivers. Trial and error method has been implemented to adjust the saturation flow. The saturation flow output has also been compared to the calculation method according to 1997 Indonesian Highway Capacity Manual. It has then been implemented to optimize signalized roundabout at Kleringan roundabout in Malioboro area, Yogyakarta, Indonesia. It is found that this method can optimize the signal setting of this roundabout. Therefore, it is recommended to use this program to optimize signalized roundabout.
Abstract: Flour from Mucuna beans (Mucuna pruriens) were
used in producing texturized meat analogue using a single screw
extruder to monitor modifications on the proximate composition and
the functional properties at high moisture level. Response surface
methodology based on Box Behnken design at three levels of barrel
temperature (110, 120, 130°C), screw speed (100,120,140rpm) and
feed moisture (44, 47, 50%) were used in 17 runs. Regression models
describing the effect of variables on the product responses were
obtained. Descriptive profile analyses and consumer acceptability
test were carried out on optimized flavoured extruded meat analogue.
Responses were mostly affected by barrel temperature and moisture
level and to a lesser extent by screw speed. Optimization results
based on desirability concept indicated that a barrel temperature of
120.15°C, feed moisture of 47% and screw speed of 119.19 rpm
would produce meat analogue of preferable proximate composition,
functional and sensory properties which reveals consumers` likeness
for the product.
Abstract: Contour filter strips planted with perennial vegetation
can be used to improve surface and ground water quality by reducing
pollutant, such as NO3-N, and sediment outflow from cropland to a
river or lake. Meanwhile, the filter strips of perennial grass with biofuel
potentials also have economic benefits of producing ethanol. In
this study, The Soil and Water Assessment Tool (SWAT) model was
applied to the Walnut Creek Watershed to examine the effectiveness
of contour strips in reducing NO3-N outflows from crop fields to the
river or lake. Required input data include watershed topography,
slope, soil type, land-use, management practices in the watershed and
climate parameters (precipitation, maximum/minimum air
temperature, solar radiation, wind speed and relative humidity).
Numerical experiments were conducted to identify potential
subbasins in the watershed that have high water quality impact, and
to examine the effects of strip size and location on NO3-N reduction
in the subbasins under various meteorological conditions (dry,
average and wet). Variable sizes of contour strips (10%, 20%, 30%
and 50%, respectively, of a subbasin area) planted with perennial
switchgrass were selected for simulating the effects of strip size and
location on stream water quality. Simulation results showed that a
filter strip having 10%-50% of the subbasin area could lead to 55%-
90% NO3-N reduction in the subbasin during an average rainfall
year. Strips occupying 10-20% of the subbasin area were found to be
more efficient in reducing NO3-N when placed along the contour
than that when placed along the river. The results of this study can
assist in cost-benefit analysis and decision-making in best water
resources management practices for environmental protection.
Abstract: In the first part of the research work, an electrolyzer (10.16 cm dia and 24.13 cm height) to produce hydrogen and oxygen was constructed for single slice O2/H2 fuel cell using cation exchange membrane. The electrolyzer performance was tested with 23% NaOH, 30% NaOH, 30% KOH and 35% KOH electrolyte solution with current input 4 amp and 2.84 V from the rectifier. Rates of volume of hydrogen produced were 0.159 cm3/sec, 0.155 cm3/sec, 0.169 cm3/sec and 0.163 cm3/sec respectively from 23% NaOH, 30% NaOH, 30% KOH and 35% KOH solution. Rates of volume of oxygen produced were 0.212 cm3/sec, 0.201 cm3/sec, 0.227 cm3/sec and 0.219 cm3/sec respectively from 23% NaOH, 30% NaOH, 30% KOH and 35% KOH solution (1.5 L). In spite of being tested the increased concentration of electrolyte solution, the gas rate does not change significantly. Therefore, inexpensive 23% NaOH electrolyte solution was chosen to use as the electrolyte in the electrolyzer. In the second part of the research work, graphite serpentine flow plates, fiberglass end plates, stainless steel screen electrodes, silicone rubbers were made to assemble the single slice O2/H2 polymer electrolyte membrane fuel cell (PEMFC).
Abstract: This research involved fingerprints on ballistics after shooting. Two objectives of research were as follow; (1) to study the duration of the existence of latent fingerprints on .38, .45, 9 mm and .223 cartridge case after shooting, and (2) to compare the effectiveness of the detection of latent fingerprints by Black Powder, Super Glue, Perma Blue and Gun Bluing. The latent fingerprint appearance were studied on .38, .45, 9 mm. and .223 cartridge cases before and after shooting with Black Powder, Super Glue, Perma Blue and Gun Bluing. The detection times were 3 minute, 6, 12, 18, 24, 30, 36, 42, 48, 54, 60, 66, 72, 78 and 84 hours respectively. As a result of the study, it can be conclude that
Before shooting, the detection of latent fingerprints on 38, .45, and 9 mm. and .223 cartridge cases with Black Powder, Super Glue, Perma Blue and Gun Bluing can detect the fingerprints at all detection times.
After shooting, the detection of latent fingerprints on .38, .45, 9 mm. and .223 cartridge cases with Black Powder, Super Glue did not appear. The detection of latent fingerprints on .38, .45, 9 mm. cartridge cases with Perma Blue and Gun Bluing were found 100% of the time and the detection of latent fingerprints on .223 cartridge cases with Perma Blue and Gun Bluing were found 40% and 46.67% of the time, respectively.
Abstract: Optimization study of the diesters biolubricant oleyl 9(12)-hydroxy-10(13)-oleioxy-12(9)-octadecanoate (OLHYOOT) was synthesized in the presence of sulfuric acid (SA) as catalyst has been done. Optimum conditions of the experiment to obtain high yield% of OLHYOOT were predicted at ratio of OL/HYOOA of 1:1 g/g, ratio of SA/HYOOA of 0.20:1 g/g, reaction temperature 110 °C and 4.5 h of reaction time. At this condition, the Yield% of OLHYOOT was 88.7. Disappearance of carboxylic acid (C=O) peak has observed by FTIR with appearance ester (C=O) at 1738 cm-1. 1H NMR spectra analyses confirmed the result of OLHYOOT with appearance ester (-CHOCOR) at 4.05ppm and also the 13C-NMR confirmed the result with appearance ester (C=O) peak at 173.93ppm.
Abstract: In the context of global climate change, flooding and sea level rise is increasingly threatening coastal urban areas, in which large population is continuously concentrated. Dutch experiences in urban water system management provide high reference value for sustainable coastal urban development projects. Preliminary studies shows the urban water system in Almere, a typical Dutch polder city, have three kinds of operational modes, achieving functions as: (1) coastline control – strong multiple damming system prevents from storm surges and maintains sufficient capacity upon risks; (2) high flexibility – large area and widely scattered open water system greatly reduce local runoff and water level fluctuation; (3) internal water maintenance – weir and sluice system maintains relatively stable water level, providing excellent boating and landscaping service, coupling with water circulating model maintaining better water quality. Almere has provided plenty of hints and experiences for ongoing development of coastal cities in emerging economies.
Abstract: The paper considered the construction of BIBDs using potential Lotto Designs (LDs) earlier derived from qualifying parent BIBDs. The study utilized Li’s condition pr t−1 ( t−1 2 ) + pr− pr t−1 (t−1) 2 < ( p 2 ) λ, to determine the qualification of a parent BIBD (v, b, r, k, λ) as LD (n, k, p, t) constrained on v ≥ k, v ≥ p, t ≤ min{k, p} and then considered the case k = t since t is the smallest number of tickets that can guarantee a win in a lottery. The (15, 140, 28, 3, 4) and (7, 7, 3, 3, 1) BIBDs were selected as parent BIBDs to illustrate the procedure. These BIBDs yielded three potential LDs each. Each of the LDs was completely generated and their properties studied. The three LDs from the (15, 140, 28, 3, 4) produced (9, 84, 28, 3, 7), (10, 120, 36, 3, 8) and (11, 165, 45, 3, 9) BIBDs while those from the (7, 7, 3, 3, 1) produced the (5, 10, 6, 3, 3), (6, 20, 10, 3, 4) and (7, 35, 15, 3, 5) BIBDs. The produced BIBDs follow the generalization (v + 1, b + r + λ + 1, r +λ+1, k, λ+1) where (v, b, r, k, λ) are the parameters of the (9, 84, 28, 3, 7) and (5, 10, 6, 3, 3) BIBDs. All the BIBDs produced are unreduced designs.
Abstract: Subsurface erosion in river banks and its details, in
spite of its occurrence in various parts of the world has rarely been
paid attention by researchers. In this paper, quantitative concept of
the subsurface bank erosion has been investigated for vertical banks.
Vertical banks were simulated experimentally by considering a sandy
erodible layer overlaid by clayey one under uniformly distributed
constant overhead pressure. Results of the experiments are indicated
that rate of sandy layer erosion is decreased by an increase in
overburden; likewise, substituting 20% of coarse (3.5 mm) sand layer
bed material by fine material (1.4 mm) may lead to a decrease in
erosion rate by one-third. This signifies the importance of the bed
material composition effect on sandy layers erosion due to subsurface
erosion in river banks.
Abstract: The purpose of this study was to explore the learning
effects on dance domain in Arts Curriculum at junior and senior high
levels. A total of 1,366 students from 9th to 11th grade of different
areas from Taiwan were administered a self-designed dance
achievement test. Data were analyzed through descriptive analysis,
independent sample t test, one-way ANOVA and Post hoc comparison
analysis using Scheffé Test. The results showed (1) female students
Abstract: The rheological properties, structure and potential synergistic interactions of whey proteins (1-6%) and inulin (20%) in mixed gels in the presence of CaCl2 was the aim of this study. Whey proteins have a strong influence on inulin gel formation. At low concentrations (2%) whey proteins did not impair in inulin gel formation. At higher concentration (4%) whey proteins impaired inulin gelation and inulin impaired the formation of a Ca2+-induced whey protein network. The presence of whey proteins at a level allowing for protein gel network formation (6%) significantly increased the rheological parameters values of the gels. SEM micrographs showed that whey protein structure was coated by inulin moieties which could make the mixed gels firmer. The protein surface hydrophobicity measurements did not exclude synergistic interactions between inulin and whey proteins, however. The use of an electrophoretic technique did not show any stable inulin-whey protein complexes.
Abstract: The conceptually construction of axially chiral indolostilbenesi.eN-(2-{(E)-2-[2'-(1-Acetyl-1H-indol-2-yl)-3'chloro-4,4',6,6'-tetramethoxy[1,1'-biphenyl]-2yl]ethenyl}phenyl)acetamide and N-(2-{(E)-2-[2'-(1-Acetyl-1H-indol-2-yl)-3'-chloro-2,4',6,6'-tetramethoxy[1,1'-biphenyl]-4-yl]ethenyl}phenyl) acetamide are described in this paper. These structure, were obtained by the tactical combination of palladium-catalyzed coupling which produced 10-acetamido-3,5-dimethoxystilbene, follow by FeCl3-induced oxidative cyclization/dimerisation. All structures were unambiguously confirmed by 1D (1H, 13C) and 2D NMR experiment, (COSY, HMQC, HMBC) and mass spectrometry.
Abstract: Fair share objective has been included into the goaloriented
parallel computer job scheduling policy recently. However,
the previous work only presented the overall scheduling performance.
Thus, the per-user performance of the policy is still lacking. In this
work, the details of per-user fair share performance under the
Tradeoff-fs(Tx:avgX) policy will be further evaluated. A basic fair
share priority backfill policy namely RelShare(1d) is also studied.
The performance of all policies is collected using an event-driven
simulator with three real job traces as input. The experimental results
show that the high demand users are usually benefited under most
policies because their jobs are large or they have a lot of jobs. In the
large job case, one job executed may result in over-share during that
period. In the other case, the jobs may be backfilled for
performances. However, the users with a mixture of jobs may suffer
because if the smaller jobs are executing the priority of the remaining
jobs from the same user will be lower. Further analysis does not show
any significant impact of users with a lot of jobs or users with a large
runtime approximation error.