Abstract: A steady two-dimensional magnetohydrodynamics
flow and heat transfer over a stretching vertical sheet influenced by
radiation and porosity is studied. The governing boundary layer
equations of partial differential equations are reduced to a system of
ordinary differential equations using similarity transformation. The
system is solved numerically by using a finite difference scheme
known as the Keller-box method for some values of parameters,
namely the radiation parameter N, magnetic parameter M, buoyancy
parameter l , Prandtl number Pr and permeability parameter K. The
effects of the parameters on the heat transfer characteristics are
analyzed and discussed. It is found that both the skin friction
coefficient and the local Nusselt number decrease as the magnetic
parameter M and permeability parameter K increase. Heat transfer
rate at the surface decreases as the radiation parameter increases.
Abstract: Power cables are vulnerable to failure due to aging or
defects that occur with the passage of time under continuous
operation and loading stresses. PD detection and characterization
provide information on the location, nature, form and extent of the
degradation. As a result, PD monitoring has become an important
part of condition based maintenance (CBM) program among power
utilities. Online partial discharge (PD) localization of defect sources
in power cable system is possible using the time of flight method.
The information regarding the time difference between the main and
reflected pulses and cable length can help in locating the partial
discharge source along the cable length. However, if the length of
the cable is not known and the defect source is located at the extreme
ends of the cable or in the middle of the cable, then double ended
measurement is required to indicate the location of PD source. Use of
multiple sensors can also help in discriminating the cable PD or local/
external PD. This paper presents the experience and results from
online partial discharge measurements conducted in the laboratory
and the challenges in partial discharge source localization.
Abstract: In this study, effects of premixed and equivalence
ratios on CO and HC emissions of a dual fuel HCCI engine are
investigated. Tests were conducted on a single-cylinder engine with
compression ratio of 17.5. Premixed gasoline is provided by a
carburetor connected to intake manifold and equipped with a screw
to adjust premixed air-fuel ratio, and diesel fuel is injected directly
into the cylinder through an injector at pressure of 250 bars. A heater
placed at inlet manifold is used to control the intake charge
temperature. Optimal intake charge temperature results in better
HCCI combustion due to formation of a homogeneous mixture,
therefore, all tests were carried out over the optimum intake
temperature of 110-115 ºC. Timing of diesel fuel injection has a great
effect on stratification of in-cylinder charge and plays an important
role in HCCI combustion phasing. Experiments indicated 35 BTDC
as the optimum injection timing. Varying the coolant temperature in
a range of 40 to 70 ºC, better HCCI combustion was achieved at 50
ºC. Therefore, coolant temperature was maintained 50 ºC during all
tests. Simultaneous investigation of effective parameters on HCCI
combustion was conducted to determine optimum parameters
resulting in fast transition to HCCI combustion. One of the
advantages of the method studied in this study is feasibility of easy
and fast transition of typical diesel engine to a dual fuel HCCI
engine. Results show that increasing premixed ratio, while keeping
EGR rate constant, increases unburned hydrocarbon (UHC)
emissions due to quenching phenomena and trapping of premixed
fuel in crevices, but CO emission decreases due to increase in CO to
CO2 reactions.
Abstract: In the recent years multimedia traffic and in particular
VoIP services are growing dramatically. We present a new algorithm
to control the resource utilization and to optimize the voice codec
selection during SIP call setup on behalf of the traffic condition
estimated on the network path.
The most suitable methodologies and the tools that perform realtime
evaluation of the available bandwidth on a network path have
been integrated with our proposed algorithm: this selects the best
codec for a VoIP call in function of the instantaneous available
bandwidth on the path. The algorithm does not require any explicit
feedback from the network, and this makes it easily deployable over
the Internet. We have also performed intensive tests on real network
scenarios with a software prototype, verifying the algorithm
efficiency with different network topologies and traffic patterns
between two SIP PBXs.
The promising results obtained during the experimental validation
of the algorithm are now the basis for the extension towards a larger
set of multimedia services and the integration of our methodology
with existing PBX appliances.
Abstract: Since the 80s huge efforts have been made to utilize
renewable energy sources to generate electric power. This paper
reports some aspects of integration of the distributed generators into
the low voltage distribution networks. An assessment of impact of the
distributed generators on the reliability indices of low voltage
network is performed. Results obtained from case study using low
voltage network, are presented and discussed.
Abstract: A diamond-like carbon (DLC) based solid-lubricant
film was designed and DLC films were successfully prepared using a
microwave plasma enhanced magnetron sputtering deposition
technology. Post-test characterizations including Raman
spectrometry, X-ray diffraction, nano-indentation test, adhesion test,
friction coefficient test were performed to study the influence of
substrate bias voltage on the mechanical properties of the W- and
S-doped DLC films. The results indicated that the W- and S-doped
DLC films also had the typical structure of DLC films and a better
mechanical performance achieved by the application of a substrate
bias of -200V.
Abstract: Due to growing environmental concerns of the cement
industry, alternative cement technologies have become an area of
increasing interest. It is now believed that new binders are
indispensable for enhanced environmental and durability
performance. Self-compacting Geopolymer concrete is an innovative
method and improved way of concreting operation that does not
require vibration for placing it and is produced by complete
elimination of ordinary Portland cement.
This paper documents the assessment of the compressive strength
and workability characteristics of low-calcium fly ash based selfcompacting
geopolymer concrete. The essential workability
properties of the freshly prepared Self-compacting Geopolymer
concrete such as filling ability, passing ability and segregation
resistance were evaluated by using Slump flow, V-funnel, L-box and
J-ring test methods. The fundamental requirements of high
flowability and segregation resistance as specified by guidelines on
Self Compacting Concrete by EFNARC were satisfied. In addition,
compressive strength was determined and the test results are included
here. This paper also reports the effect of extra water, curing time and
curing temperature on the compressive strength of self-compacting
geopolymer concrete. The test results show that extra water in the
concrete mix plays a significant role. Also, longer curing time and
curing the concrete specimens at higher temperatures will result in
higher compressive strength.
Abstract: The case study was conducted to show the effect of milking method in goat called half day milking on the milk production and the growth of kids. Data were collected by interviewing farmers and investigating goat production in the communal goat housing from June 2008 to May 2009. The interview was conducted to collect data about goat management. The observations were conducted on 10 goats, which were selected based on the uniformity of age, number of kid born/goat and the milking method in practice. The samples were divided into two groups; those were full 3 months nursing and half day milked goats (in this group the kids were separated from goat during the previous night milking and then the kids were allowed to suck the goat during the day). The result showed that the communal goat housing had 138 goats and 25% of the farmers milked the goat. The implementation of half day milking increased the milk production significantly (P
Abstract: Mathematical justifications are given for a simulation technique of multivariate nonGaussian random processes and fields based on Rosenblatt-s transformation of Gaussian processes. Different types of convergences are given for the approaching sequence. Moreover an original numerical method is proposed in order to solve the functional equation yielding the underlying Gaussian process autocorrelation function.
Abstract: A subcarrier - spectral amplitude coding optical code
division multiple access system using the Khazani-Syed code with
Complementary subtraction detection technique is proposed. The
proposed system has been analyzed by taking into account the effects
of phase-induced intensity noise, shot noise, thermal noise and intermodulation
distortion noise. The performance of the system has been
compared with the spectral amplitude coding optical code division
multiple access system using the Hadamard code and the Modified
Quadratic Congruence code. The analysis shows that the proposed
system can eliminate the multiple access interference using the
Complementary subtraction detection technique, and hence improve
the overall system performance.
Abstract: This paper aims to perform the second law analysis of
thermodynamics on the laminar film condensation of pure saturated
vapor flowing in the direction of gravity on an ellipsoid with variable
wall temperature. The analysis provides us understanding how the
geometric parameter- ellipticity and non-isothermal wall temperature
variation amplitude “A." affect entropy generation during film-wise
condensation heat transfer process. To understand of which
irreversibility involved in this condensation process, we derived an
expression for the entropy generation number in terms of ellipticity
and A. The result indicates that entropy generation increases with
ellipticity. Furthermore, the irreversibility due to finite temperature
difference heat transfer dominates over that due to condensate film
flow friction and the local entropy generation rate decreases with
increasing A in the upper half of ellipsoid. Meanwhile, the local
entropy generation rate enhances with A around the rear lower half of
ellipsoid.
Abstract: Introduction: Obesity is a major health risk issue in
the present day of life for one and all globally. Obesity is one of the
major concerns for public health according to recent increasing trends
in obesity-related diseases such as Type 2 diabetes. ( Kazuya,
1994).and hyperlipidemia, (Sakata,1990) .which are more prevalent
in Japanese adults with body mass index (BMI) values Z25 kg/m2.(
Japanese Ministry of Health and Welfare,1997). The purpose of the
study was to assess the effect of twelve weeks of brisk walking on
blood pressure and body mass index, anthropometric measurements
of obese males. Method: Thirty obese (BMI= above 30) males, aged
18 to 22 years, were selected from King Fahd University of
Petroleum & Minerals, Saudi Arabia. The subject-s height (cm) was
measured using a stadiometer and body mass (kg) was measured with
a electronic weighing machine. BMI was subsequently calculated
(kg/m2). The blood pressure was measured with standardized
sphygmomanometer in mm of Hg. All the measurements were taken
twice before and twice after the experimental period. The pre and
post anthropometric measurements of waist and hip circumference
were measured with the steel tape in cm. The subjects underwent
walking schedule two times in a week for 12 weeks. The 45 minute
sessions of brisk walking were undertaken at an average intensity of
65% to 85% of maximum HR (HRmax; calculated as 220-age).
Results & Discussion: Statistical findings revealed significant
changes from pre test to post test in case of both systolic blood
pressure and diastolic blood pressure in the walking group. Results
also showed significant decrease in their body mass index and
anthropometric measurements i.e. (waist & hip circumference).
Conclusion: It was concluded that twelve weeks brisk walking is
beneficial for lowering of blood pressure, body mass index, and
anthropometric circumference of obese males.
Abstract: Physical urban form is recognized to be the media for
human transactions. It directly influences the travel demand of people
in a specific urban area and the amount of energy used for
transportation. Distorted, sprawling form often creates sustainability
problems in urban areas. It is declared in EU strategic planning
documents that compact urban form and mixed land use pattern must
be given the main focus to achieve better sustainability in urban
areas, but the methods to measure and compare these characteristics
are still not clear.
This paper presents the simple methods to measure the spatial
characteristics of urban form by analyzing the location and
distribution of objects in an urban environment. The extended CA
(cellular automata) model is used to simulate urban development
scenarios.
Abstract: Medical negligence disputes in Malaysia are mainly resolved through litigation by using the tort system. The tort system, being adversarial in nature has subjected parties to litigation hazards such as delay, excessive costs and uncertainty of outcome. The dissatisfaction of the tort system in compensating medically injured victims has created various alternatives to litigation. Amongst them is the implementation of a no-fault compensation system which would allow compensation to be given without the need of proving fault on the medical personnel. Instead, the community now bears the burden of compensating and at the end, promotes collective responsibility. For Malaysia, introducing a no-fault system would provide a tempting solution and may ultimately, achieve justice for the medical injured victims. Nevertheless, such drastic change requires a great deal of consideration to determine the suitability of the system and whether or not it will eventually cater for the needs of the Malaysian population
Abstract: This paper focuses on wormhole attacks detection in wireless sensor networks. The wormhole attack is particularly challenging to deal with since the adversary does not need to compromise any nodes and can use laptops or other wireless devices to send the packets on a low latency channel. This paper introduces an easy and effective method to detect and locate the wormholes: Since beacon nodes are assumed to know their coordinates, the straight line distance between each pair of them can be calculated and then compared with the corresponding hop distance, which in this paper equals hop counts × node-s transmission range R. Dramatic difference may emerge because of an existing wormhole. Our detection mechanism is based on this. The approximate location of the wormhole can also be derived in further steps based on this information. To the best of our knowledge, our method is much easier than other wormhole detecting schemes which also use beacon nodes, and to those have special requirements on each nodes (e.g., GPS receivers or tightly synchronized clocks or directional antennas), ours is more economical. Simulation results show that the algorithm is successful in detecting and locating wormholes when the density of beacon nodes reaches 0.008 per m2.
Abstract: Most of the image watermarking methods, using the properties of the human visual system (HVS), have been proposed in literature. The component of the visual threshold is usually related to either the spatial contrast sensitivity function (CSF) or the visual masking. Especially on the contrast masking, most methods have not mention to the effect near to the edge region. Since the HVS is sensitive what happens on the edge area. This paper proposes ultrasound image watermarking using the visual threshold corresponding to the HVS in which the coefficients in a DCT-block have been classified based on the texture, edge, and plain area. This classification method enables not only useful for imperceptibility when the watermark is insert into an image but also achievable a robustness of watermark detection. A comparison of the proposed method with other methods has been carried out which shown that the proposed method robusts to blockwise memoryless manipulations, and also robust against noise addition.
Abstract: This paper presents a system for discovering
association rules from collections of unstructured documents called
EART (Extract Association Rules from Text). The EART system
treats texts only not images or figures. EART discovers association
rules amongst keywords labeling the collection of textual documents.
The main characteristic of EART is that the system integrates XML
technology (to transform unstructured documents into structured
documents) with Information Retrieval scheme (TF-IDF) and Data
Mining technique for association rules extraction. EART depends on
word feature to extract association rules. It consists of four phases:
structure phase, index phase, text mining phase and visualization
phase. Our work depends on the analysis of the keywords in the
extracted association rules through the co-occurrence of the keywords
in one sentence in the original text and the existing of the keywords
in one sentence without co-occurrence. Experiments applied on a
collection of scientific documents selected from MEDLINE that are
related to the outbreak of H5N1 avian influenza virus.
Abstract: In this paper, we present an analytical analysis of the
representation of images as the magnitudes of their transform with
the discrete wavelets. Such a representation plays as a model for
complex cells in the early stage of visual processing and of high
technical usefulness for image understanding, because it makes the
representation insensitive to small local shifts. We found that if the
signals are band limited and of zero mean, then reconstruction from
the magnitudes is unique up to the sign for almost all signals. We
also present an iterative reconstruction algorithm which yields very
good reconstruction up to the sign minor numerical errors in the very
low frequencies.
Abstract: Mobile learning (m-learning) is a new method in teaching and learning process which combines technology of mobile device with learning materials. It can enhance student's engagement in learning activities and facilitate them to access the learning materials at anytime and anywhere. In Kolej Poly-Tech Mara (KPTM), this method is seen as an important effort in teaching practice and to improve student learning performance. The aim of this paper is to discuss the development of m-learning application called Mobile EEF Learning System (MEEFLS) to be implemented for Electric and Electronic Fundamentals course using Flash, XML (Extensible Markup Language) and J2ME (Java 2 micro edition). System Development Life Cycle (SDLC) was used as an application development approach. It has three modules in this application such as notes or course material, exercises and video. MEELFS development is seen as a tool or a pilot test for m-learning in KPTM.
Abstract: The Non-Rotating Adjustable Stabilizer / Directional
Solution (NAS/DS) is the imitation of a mechanical process or an
object by a directional drilling operation that causes a respond
mathematically and graphically to data and decision to choose the
best conditions compared to the previous mode.
The NAS/DS Auto Guide rotary steerable tool is undergoing final
field trials. The point-the-bit tool can use any bit, work at any
rotating speed, work with any MWD/LWD system, and there is no
pressure drop through the tool. It is a fully closed-loop system that
automatically maintains a specified curvature rate.
The Non–Rotating Adjustable stabilizer (NAS) can be controls
curvature rate by exactly positioning and run with the optimum bit,
use the most effective weight (WOB) and rotary speed (RPM) and
apply all of the available hydraulic energy to the bit. The directional
simulator allowed to specify the size of the curvature rate
performance errors of the NAS tool and the magnitude of the random
errors in the survey measurements called the Directional Solution
(DS).
The combination of these technologies (NAS/DS) will provide
smoother bore holes, reduced drilling time, reduced drilling cost and
incredible targeting precision. This simulator controls curvature rate
by precisely adjusting the radial extension of stabilizer blades on a
near bit Non-Rotating Stabilizer and control process corrects for the
secondary effects caused by formation characteristics, bit and tool
wear, and manufacturing tolerances.