Abstract: Nitrification is essential to biological processes
designed to remove ammonia and/or total nitrogen. It removes excess
nitrogenous compound in wastewater which could be very toxic to
the aquatic fauna or cause serious imbalance of such aquatic
ecosystem. Efficient nitrification is linked to an in-depth knowledge
of the structure and dynamics of the nitrifying community structure
within the wastewater treatment systems. In this study, molecular
technique was employed for characterizing the microbial structure of
activated sludge [ammonia oxidizing bacteria (AOB) and nitrite
oxidizing bacteria (NOB)] in a municipal wastewater treatment with
intention of linking it to the plant efficiency. PCR based phylogenetic
analysis was also carried out. The average operating and
environmental parameters as well as specific nitrification rate of plant
was investigated during the study. During the investigation the average temperature was 23±1.5oC.
Other operational parameters such as mixed liquor suspended solids
and chemical oxygen demand inversely correlated with ammonia
removal. The dissolved oxygen level in the plant was constantly
lower than the optimum (between 0.24 and 1.267 mg/l) during this
study. The plant was treating wastewater with influent ammonia
concentration of 31.69 and 24.47 mg/L. The influent flow rates
(ML/Day) was 96.81 during period. The dominant nitrifiers include:
Nitrosomonas spp. Nitrobacter spp. and Nitrospira spp. The AOB
had correlation with nitrification efficiency and temperature. This
study shows that the specific ammonia oxidizing rate and the specific
nitrate formation rates can serve as good indicator of the plant overall
nitrification performance.
Abstract: There are a number of Distributed Generations (DGs)
installed in microgrid, which may have diverse path and direction of
power flow or fault current. The overcurrent protection scheme for the
traditional radial type distribution system will no longer meet the
needs of microgrid protection. Integrating the Intelligent Electronic
Device (IED) and a Supervisory Control and Data Acquisition
(SCADA) with IEC 61850 communication protocol, the paper
proposes a Microgrid Protection Management System (MPMS) to
protect power system from the fault. In the proposed method, the
MPMS performs logic programming of each IED to coordinate their
tripping sequence. The GOOSE message defined in IEC 61850 is used
as the transmission information medium among IEDs. Moreover, to
cope with the difference in fault current of microgrid between
grid-connected mode and islanded mode, the proposed MPMS applies
the group setting feature of IED to protect system and robust
adaptability. Once the microgrid topology varies, the MPMS will
recalculate the fault current and update the group setting of IED.
Provided there is a fault, IEDs will isolate the fault at once. Finally, the
Matlab/Simulink and Elipse Power Studio software are used to
simulate and demonstrate the feasibility of the proposed method.
Abstract: Sweden has succeeded to maintain a high level of
growth and development and has managed to sustain highly ranked
position among the world’s developed countries. In this regard,
Swedish universities are playing a vital role in supporting innovation
and entrepreneurship at all levels and developing Swedish knowledge
economy. This paper is aiming to draw on the experiences of two leading
Swedish universities, addressing their transformation approach to
create entrepreneurial universities and fulfilling their objectives in the
era of knowledge economy. The objectives of the paper include: 1) Introducing the Swedish
higher education and its characteristics. 2) Examining the
infrastructure elements for innovation and Entrepreneurship at two of
the Swedish entrepreneurial universities. 3) Addressing the key
aspects of support systems in the initiatives of both Chalmers and
Gothenburg universities to support innovation and advance
entrepreneurial practices. The paper will contribute to two discourses: 1) Examining the
relationship between support systems for innovation and
entrepreneurship and the Universities’ policies and practices. 2)
Lessons for University leaders to assist the development and
implementation of effective innovation and entrepreneurship policies
and practices.
Abstract: Unsatisfactory experiences due to an information shortage regarding the future pay-offs of actual choices, yield satisficing decision-making. This research will examine, for the first time in the literature, the motivation behind suboptimal decisions due to uncertainty by subjecting Adam Smith’s and Jeremy Bentham’s assumptions about the nature of the actions that lead to satisficing behavior, in order to clarify the theoretical background of a “consumption-based satisfactory time” concept. The contribution of this paper with respect to the existing literature is threefold: firstly, it is showed in this paper that Adam Smith’s uncertainty is related to the problem of the constancy of ideas and not related directly to beliefs. Secondly, possessions, as in Jeremy Bentham’s oeuvre, are assumed to be just as pleasing, as protecting and improving the actual or expected quality of life, so long as they reduce any displeasure due to the undesired outcomes of uncertainty. Finally, each consumption decision incurs its own satisfactory time period, owed to not feeling hungry, being healthy, not having transportation…etc. This reveals that the level of satisfaction is indeed a behavioral phenomenon where its value would depend on the simultaneous satisfaction derived from all activities.
Abstract: The web services applications for digital reference
service (WSDRS) of LIS model is an informal model that claims to
reduce the problems of digital reference services in libraries. It uses
web services technology to provide efficient way of satisfying users’
needs in the reference section of libraries. The formal WSDRS model
consists of the Z specifications of all the informal specifications of
the model. This paper discusses the formal validation of the Z
specifications of WSDRS model. The authors formally verify and
thus validate the properties of the model using Z/EVES theorem
prover.
Abstract: Objective: Sharing devastating news with patients is
often considered the most difficult task of doctors. This study aimed
to explore patients’ perceptions of receiving bad news including
which features improve the experience and which areas need refining. Methods: A questionnaire was written based on the steps of the
SPIKES model for breaking bad new. 20 patients receiving treatment
for a hematological malignancy completed the questionnaire. Results: Overall, the results are promising as most patients praised
their consultation. ‘Poor’ was more commonly rated by women and
participants aged 45-64. The main differences between the ‘excellent’
and ‘poor’ consultations include the doctor’s sensitivity and checking
the patients’ understanding. Only 35% of patients were asked their
existing knowledge and 85% of consultations failed to discuss the
impact of the diagnosis on daily life. Conclusion: This study agreed with the consensus of existing
literature. The commended aspects include consultation set-up and
information given. Areas patients felt needed improvement include
doctors determining the patient’s existing knowledge and checking
new information has been understood. Doctors should also explore
how the diagnosis will affect the patient’s life. With a poorer
prognosis, doctors should work on conveying appropriate hope. The
study was limited by a small sample size and potential recall bias.
Abstract: Web mining is to discover and extract useful
Information. Different users may have different search goals when
they search by giving queries and submitting it to a search engine.
The inference and analysis of user search goals can be very useful for
providing an experience result for a user search query. In this project,
we propose a novel approach to infer user search goals by analyzing
search web logs. First, we propose a novel approach to infer user
search goals by analyzing search engine query logs, the feedback
sessions are constructed from user click-through logs and it
efficiently reflect the information needed for users. Second we
propose a preprocessing technique to clean the unnecessary data’s
from web log file (feedback session). Third we propose a technique
to generate pseudo-documents to representation of feedback sessions
for clustering. Finally we implement k-medoids clustering algorithm
to discover different user search goals and to provide a more optimal
result for a search query based on feedback sessions for the user.
Abstract: This study was carried out for an underground subway station at Seoul Metro, Korea. The optimal set-points of the ventilation control system are determined every 3 hours, then, the ventilation controller adjusts the ventilation fan speed according to the optimal set-point changes. Compared to manual ventilation system which is operated irrespective of the OAQ, the IDP-based ventilation control system saves 3.7% of the energy consumption. Compared to the fixed set-point controller which is operated irrespective of the IAQ diurnal variation, the IDP-based controller shows better performance with a 2% decrease in energy consumption, maintaining the comfortable IAQ range inside the station.
Abstract: The access to relevant information that is adapted to
user’s needs, preferences and environment is a challenge in many
applications running. That causes an appearance of context-aware
systems. To facilitate the development of this class of applications, it
is necessary that these applications share a common context
metamodel. In this article, we will present our context metamodel
that is defined using the OMG Meta Object facility (MOF).This
metamodel is based on the analysis and synthesis of context concepts
proposed in literature.
Abstract: The aim of the current work was to employ the finite
element method to model a slab, with a small hole across its width,
undergoing plastic plane strain deformation. The computational
model had, however, to be validated by comparing its results with
those obtained experimentally. Since they were in good agreement,
the finite element method can therefore be considered a reliable tool
that can help gain better understanding of the mechanism of ductile
failure in structural members having stress raisers. The finite element
software used was ANSYS, and the PLANE183 element was utilized.
It is a higher order 2-D, 8-node or 6-node element with quadratic
displacement behavior. A bilinear stress-strain relationship was used
to define the material properties, with constants similar to those of the
material used in the experimental study. The model was run for
several tensile loads in order to observe the progression of the plastic
deformation region, and the stress concentration factor was
determined in each case. The experimental study involved employing the visioplasticity
technique, where a circular mesh (each circle was 0.5 mm in
diameter, with 0.05 mm line thickness) was initially printed on the
side of an aluminum slab having a small hole across its width.
Tensile loading was then applied to produce a small increment of
plastic deformation. Circles in the plastic region became ellipses,
where the directions of the principal strains and stresses coincided
with the major and minor axes of the ellipses. Next, we were able to
determine the directions of the maximum and minimum shear
stresses at the center of each ellipse, and the slip-line field was then
constructed. We were then able to determine the stress at any point in
the plastic deformation zone, and hence the stress concentration
factor. The experimental results were found to be in good agreement
with the analytical ones.
Abstract: The goal of the modern education system is to prepare
students to be able to adapt to ever-changing life situations. They
must be able to acquire required knowledge independently; apply
such knowledge in practice to solve various problems by using
modern technologies; think critically and creatively; competently use
information; be communicative, work in a team; and develop their
own moral values, intellect and cultural awareness. As a result, the
status of education significantly increases; new requirements to its
quality have been formed. In recent years the competency-based
approach in education has become of significant interest. This
approach is a strengthening of applied and practical characteristics of
a school education and leads to the forming of the key students’
competencies which define their success in future life. In this article,
the authors’ attention focuses on a range of key competencies,
educational, informational and communicative and on the possibility
to develop such competencies via STEM education. This research
shows the change in students’ attitude towards scientific disciplines
such as mathematics, general science, technology and engineering as
a result of STEM education. Two staged analyzed questionnaires
completed by students of forms II to IV in the republic of Trinidad
and Tobago allowed the authors to categorize students between two
levels that represent students’ attitude to various disciplines. The
significance of differences between selected levels was confirmed
with the use of Pearson’s chi-squared test. In summary, the analysis
of obtained data makes it possible to conclude that STEM education
has a great potential for development of core students’ competencies
and encourage the development of positive student attitude towards
the above mentioned above scientific disciplines.
Abstract: Information technology plays an irreplaceable role in
introducing and improving business process orientation in a
company. It enables implementation of the theoretical concept,
measurement of results achieved and undertaking corrective
measures aimed at improvements. Information technology is a key
concept in the development and implementation of the business
process management systems as it establishes a connection to
business operations. Both in the literature and practice, insurance
companies are often seen as highly process oriented due to the nature
of their business and focus on customers. They are also considered
leaders in using information technology for business process
management. The research conducted aimed to investigate whether
the perceived leadership status of insurance companies is well
deserved, i.e. to establish the level of process orientation and explore
the practice of information technology use in insurance companies in
the region. The main instrument for primary data collection within
this research was an electronic survey questionnaire sent to the
management of insurance companies in the Republic of Croatia,
Bosnia and Herzegovina, Slovenia, Serbia and Macedonia. The
conducted research has shown that insurance companies have a
satisfactory level of process orientation, but that there is also a huge
potential for improvement, especially in the segment of information
technology and its connection to business processes.
Abstract: In recent years, the use of the aluminum based alloys
in the industry and technology are increasing. Alloying elements in
aluminum have further been improving the strength and stiffness
properties that provide superior compared to other metals. In this
study, investigation of physical properties (microstructure,
microhardness, tensile strength, electrical conductivity and thermal
properties) in the Al-12.6wt.%Si-%2wt.Ni ternary alloy were
investigated. Al-Si-Ni alloy was prepared in vacuum atmosphere. The
samples were directionally solidified upwards with different growth
rate V (8.3−165.45 μm/s) at constant temperature gradient G (7.73
K/mm). The flake spacings (λ), microhardness (HV), ultimate tensile
strength (σ), electrical resistivity (ρ) and thermal properties (H, Cp,
Tm) of the samples were measured. Influence of the growth rate and
spacings on microhardness, ultimate tensile strength and electrical
resistivity were investigated and relationships between them were
obtained. According to results, λ values decrease with increasing V,
but HV, σ and ρ values increase with increasing V. Variations of
electrical resistivity (ρ) of solidified samples were also measured.
The enthalpy of fusion (H) and specific heat (Cp) for the alloy was
also determined by differential scanning calorimeter (DSC) from
heating trace during the transformation from liquid to solid. The
results in this work were compared with the previous similar
experimental results.
Abstract: The localization information is crucial for the
operation of WSN. There are principally two types of localization
algorithms. The Range-based localization algorithm has strict
requirements on hardware, thus is expensive to be implemented in
practice. The Range-free localization algorithm reduces the hardware
cost. However, it can only achieve high accuracy in ideal scenarios.
In this paper, we locate unknown nodes by incorporating the
advantages of these two types of methods. The proposed algorithm
makes the unknown nodes select the nearest anchor using the
Received Signal Strength Indicator (RSSI) and choose two other
anchors which are the most accurate to achieve the estimated
location. Our algorithm improves the localization accuracy compared
with previous algorithms, which has been demonstrated by the
simulating results.
Abstract: In this article, a method is presented to effectively
estimate the deformed shape of a thick plate due to line heating. The
method uses a fifth order spline interpolation, with up to C3
continuity at specific points to compute the shape of the deformed
geometry. First and second order derivatives over a surface are the
resulting parameters of a given heating line on a plate. These
parameters are determined through experiments and/or finite element
simulations. Very accurate kriging models are fitted to real or virtual
surfaces to build-up a database of maps. Maps of first and second
order derivatives are then applied on numerical plate models to
evaluate their evolving shapes through a sequence of heating lines.
Adding an optimization process to this approach would allow
determining the trajectories of heating lines needed to shape complex
geometries, such as Francis turbine blades.
Abstract: Despite the financial crisis and ongoing need for cost
cutting, companies all around the world heavily invest in Information
Systems (IS) and underlying Information Technology (IT).
Proliferation of governance of enterprise IT helps companies manage,
or rather, governs IS as a primary business function with executive
management involved in making decision about IS and IT. The
business value of IT is raising with the involvement of the executive
management in IT decision making process and quality IT
governance mechanisms in place. In this paper the practice of
governing the enterprise IT will be investigated on a sample of the
largest 100 Croatian companies. Research questions posed here will
reveal if there are some formal IT governance mechanisms, are there
any differences in perceived role of IS and IT between CIOs (Chief
Information Officers) and CEOs (Chief Executive Officers) of the
sampled companies and what are the mechanisms to govern massive
investment in enterprise IT.
Abstract: Below-knee amputees commonly experience
asymmetrical gait patterns. It is generally believed that ischemia is
related to the formation of pressure sores due to uneven distribution
of forces. Micro-vascular responses can reveal local malnutrition.
Changes in local skin blood supply under various external loading
conditions have been studied for a number of years. Radionuclide
clearance, photo-plethysmography, trans-cutaneous oxygen tension
along with other studies showed that the blood supply would be
influenced by the epidermal forces, and the rate and the amount of
blood supply would decrease with increased epidermal loads being
shear forces or normal forces. Several cases of socket designs were
investigated using Finite Element Model (FEM) and Design of
Experiment (DOE) to increase flexibility and minimize the pressure
at the limb/socket interface using ultra high molecular weight
polyethylene (UHMWPE) and polyamide 6 (PA6) or Duraform. The
pressure reliefs at designated areas where reducing thickness is
involved are seen to be critical in determination of amputees’ comfort
and are very important to clinical applications. Implementing a hole
between the Patellar Tendon (PT) and Distal Tibia (DT) would
decrease stiffness and increase prosthesis range of motion where
flexibility is needed. In addition, displacement and prosthetic energy
storage increased without compromising mechanical efficiency and
prosthetic design integrity.
Abstract: The main objective of MEAL is to develop a
pedagogical tool aimed to help teachers and nutritionists (students
and professionals) to acquire, train, promote and deliver to children
basic nutritional education and healthy eating behaviours
competencies. MEAL is focused on eating behaviours and not only in
nutritional literacy, and will use new technologies like Information
and Communication Technologies (ICTs) and serious games (SG)
platforms to consolidate the nutritional competences and habits.
Abstract: This paper treats different aspects of entropy measure
in classical information theory and statistical quantum mechanics, it
presents the possibility of extending the definition of Von Neumann
entropy to image and array processing. In the first part, we generalize
the quantum entropy using singular values of arbitrary rectangular
matrices to measure the randomness and the quality of denoising
operation, this new definition of entropy can be implemented to
compare the performance analysis of filtering methods. In the second
part, we apply the concept of pure state in quantum formalism
to generalize the maximum entropy method for narrowband and
farfield source localization problem. Several computer simulation
results are illustrated to demonstrate the effectiveness of the proposed
techniques.
Abstract: In this paper, monitoring and control of tap changer
mechanism of a transformer implementation in an Intelligent
Electronic Device (IED) is discussed. It has been a custom for
decades to provide a separate panel for on load tap changer control
for monitoring the tap position. However, this facility cannot either
record or transfer the information to remote control centers. As there
is a technology shift towards the smart grid protection and control
standards, the need for implementing remote control and monitoring
has necessitated the implementation of this feature in numerical
relays. This paper deals with the programming, settings and logic
implementation which is applicable to both IEC 61850 compatible
and non-compatible IEDs thereby eliminating the need for separate
tap changer control equipment. The monitoring mechanism has been
implemented in a 28MVA, 110 /6.9kV transformer with 16 tap
position with GE make T60 IED at Ultratech cement limited
Gulbarga, Karnataka and is in successful service.