Abstract: The available studies in the literature which dealt with the scale effects of strip footings on different sand packing systematically still remain scarce. In this research, the variation of ultimate bearing capacity and deformation pattern of soil beneath strip footings of different widths under plane-strain condition on the surface of loose, medium-dense and dense sand have been systematically studied using experimental and noninvasive methods for measuring microscopic deformations. The presented analyses are based on model scale compression test analysed using Particle Image Velocimetry (PIV) technique. Upper bound analysis of the current study shows that the maximum vertical displacement of the sand under the ultimate load increases for an increase in the width of footing, but at a decreasing rate with relative density of sand, whereas the relative vertical displacement in the sand decreases for an increase in the width of the footing. A well agreement is observed between experimental results for different footing widths and relative densities. The experimental analyses have shown that there exists pronounced scale effect for strip surface footing. The bearing capacity factors Nγ rapidly decrease up to footing widths B=0.25 m, 0.35 m, and 0.65 m for loose, medium-dense and dense sand respectively, after that there is no significant decrease in Nγ. The deformation modes of the soil as well as the ultimate bearing capacity values have been affected by the footing widths. The obtained results could be used to improve settlement calculation of the foundation interacting with granular soil.
Abstract: The objective of the present study was to determine the polymorphism in the leptin (332G>A) and its association with biometric traits in Sanjabi sheep. For this purpose, blood samples from 96 rams were taken, and tail length, width tail, circumference tail, body length, body width, and height were simultaneously recorded. PCR was performed using specific primer to amplify 463 bp fragment including exon 3 of leptin gene, and PCR products were digested by Cail restriction enzymes. The 332G>A (at 332th nucleotide of exon 3 leptin gene) that caused an amino acid change from Arg to Gln was detected by Cail (CAGNNNCTG) endonuclease, as the endonuclease cannot cut this region if G nucleotide is located in this position. Three genotypes including GG (463), GA (463, 360and 103 bp) and GG (360 bp and 103 bp) were identified after digestion by enzyme. The estimated frequencies of three genotypes including GG, GA, and AA for 332G>A locus were 0.68, 0.29 and 0.03 and those were 0.18 and 0.82 for A and G alleles, respectively. In the current study, chi-square test indicated that 332G>A positions did not deviate from the Hardy–Weinberg (HW) equilibrium. The most important reason to show HW equation was that samples used in this study belong to three large local herds with a traditional breeding system having random mating and without selection. Shannon index amount was calculated which represent an average genetic variation in Sanjabi rams. Also, heterozygosity estimated by Nei index indicated that genetic diversity of mutation in the leptin gene is moderate. Leptin gene polymorphism in the 332G>A had significant effect on body length (P0.05). This non-synonymous SNP resulted in different amino acid changes at codon positions111(R/Q). As leptin activity is localized, at least in part, in domains between amino acid residues 106-1406, it is speculated that the detected SNP at position 332 may affect the activity of leptin and may lead to different biological functions. Based to our results, due to significant effect of leptin gene polymorphism on body size traits, this gene may be used a candidate gene for improving these traits.
Abstract: The growing awareness of global warming potential has internationally aroused interest and demand in reducing greenhouse gas emissions produced by human activity. Much national energy in the UK had been consumed in the residential sector mainly for space heating and domestic hot water production. Currently, gas boilers are mostly applied in the domestic water heating which contribute significantly to excessive CO2 emissions and consumption of primary energy resources. The issues can be solved by popularizing heat pump systems that are attributable to higher performance efficiency than those of traditional gas boilers. Even so, the heat pump system performance can be further enhanced if the dissolved gases in its hot water circuit can be efficiently discharged. To achieve this target, the bubble behaviors in the heat pump water heating system need to be extensively investigated. In this paper, by varying different experimental conditions, the effects of various heat pump hot water side parameters on gas microbubble diameters were measured and analyzed. Correspondingly, the effect of each parameter has been investigated. These include varied system pressures, water flow rates, saturation ratios and heat outputs. The results measurement showed that the water flow rate is the most significant parameter to influence on gas microbubble productions. The research outcomes can significantly contribute to the understanding of gas bubble behaviors at domestic heat pump water heating systems and thus the efficient way for the discharging of the associated dissolved gases.
Abstract: Nowadays, tunnels with different applications are developed, and most of them are related to subway tunnels. The excavation of shallow tunnels that pass under municipal utilities is very important, and the surface settlement control is an important factor in the design. The study sought to analyze the settlement and also to find an appropriate model in order to predict the behavior of the tunnel in Tehran subway line-3. The displacement in these sections is also determined by using numerical analyses and numerical modeling. In addition, the Adaptive Neuro-Fuzzy Inference System (ANFIS) method is utilized by Hybrid training algorithm. The database pertinent to the optimum network was obtained from 46 subway tunnels in Iran and Turkey which have been constructed by the new Austrian tunneling method (NATM) with similar parameters based on type of their soil. The surface settlement was measured, and the acquired results were compared to the predicted values. The results disclosed that computing intelligence is a good substitute for numerical modeling.
Abstract: The effects of type and amount of solvent on lubricant which is used in disposable medical devices are investigated in this article. Two kinds of common solvent, n-Hexane and n-Heptane, are used. The mechanical behavior of syringe has shown that n-Heptane has better mixing ratio and also more effective spray process in the barrel of syringe than n-Hexane because of similar solubility parameter to silicon oil. The results revealed that movement of plunger in the barrel increases when pure silicone is used because non-uniform film is created on the surface of barrel, and also, it seems that the form of silicon is converted from oil to gel due to sterilization process. The results showed that the convenient mixing ratio of solvent/lubricant oil is 80/20.
Abstract: Cerebral palsy is primarily reflected in the disorder of the development of movement and posture, which may be accompanied by sensory disturbances, disturbances of perception, cognition and communication, behavioural disorders and epilepsy. According to current inclusive attitudes towards people with disabilities implies that full social participation of children with cerebral palsy means inclusion in all activities in family, peer, school and leisure environments in the same scope and to the same extent as is the case with the children of proper development and without physical difficulties. Due to the fact that it has been established that the quality of children's participation in primary school is directly related to their social inclusion in future life, the aim of the paper is to identify predictors of social participation, respectively, and in particular, factors that could to improve the quality of social participation of children with cerebral palsy, in the primary school environment in Czech Republic. The study includes children with cerebral palsy (n = 75) in the Czech Republic, aged between six and 12 years who attend mainstream or special primary schools to the sixth grade. The main instrument used was the first and third part of the School function assessment questionnaire. It will also take into account the type of damage assessed according to a scale the Gross motor function classification system, five–level classification system for cerebral palsy. The research results will provide detailed insight into the degree of social participation of children with cerebral palsy and the factors that would be a potential cause of their levels of participation, in regular and special primary schools, in different socioeconomic environments in Czech Republic.
Abstract: High density of high rise buildings in urban areas lead to a deteriorative Urban Heat Island Effect, gradually. This study focuses on discussing the relationship between urban layout and ventilation comfort in street canyons. This study takes Songjiang Nanjing Rd. area of Taipei, Taiwan as an example to evaluate the wind environment comfort index by field measurement and Computational Fluid Dynamics (CFD) to improve both the quality and quantity of the environment. In this study, different factors including street blocks size, the width of buildings, street width ratio and the direction of the wind were used to discuss the potential of ventilation. The environmental wind field was measured by the environmental testing equipment, Testo 480. Evaluation of blocks sizes, the width of buildings, street width ratio and the direction of the wind was made under the condition of constant floor area with the help of Stimulation CFD to adjust research methods for optimizing regional wind environment. The results of this study showed the width of buildings influences the efficiency of outdoor ventilation; improvement of the efficiency of ventilation with large street width was also shown. The study found that Block width and H/D value and PR value has a close relationship. Furthermore, this study showed a significant relationship between the alteration of street block geometry and outdoor comfortableness.
Abstract: The process of post-supercritical CO2 electroplating uses the electrolyte solution after being mixed with supercritical CO2 and released to atmospheric pressure. It utilizes the microbubbles that form when oversaturated CO2 in the electrolyte returns to gaseous state, which gives the similar effect of pulsed electroplating. Under atmospheric pressure, the CO2 bubbles gradually diffuse. Therefore, the introduction of ultrasound and/or other agitation can potentially excite the CO2 microbubbles to achieve an electroplated surface of even higher quality. In this study, during the electroplating process, three different modes of agitation: magnetic stirrer agitation, ultrasonic agitation and a combined mode (magnetic + ultrasonic) were applied, respectively, in order to obtain an optimal surface morphology and mechanical properties for the electroplated Ni coating. It is found that the combined agitation mode at a current density of 40 A/dm2 achieved the smallest grain size, lower surface roughness, and produced an electroplated Ni layer that achieved hardness of 320 HV, much higher when compared with conventional method, which were usually in the range of 160 to 300 HV. However, at the same time, the electroplating with combined agitation developed a higher internal stress of 320 MPa due to the lower current efficiency of the process and finer grain in the coating. Moreover, a new control methodology for tailoring the coating’s mechanical property through its thickness was demonstrated by the timely introduction of ultrasonic agitation during the electroplating process with post supercritical CO2 mixed electrolyte.
Abstract: Landfills present long-term threats to soil, air, groundwater and surface water due to the formation of greenhouse gases (methane gas and carbon dioxide) and leachate from decomposing garbage. The composition of leachate differs from site to site and also within the landfill. The leachates alter with time (from weeks to years) since the landfilled waste is biologically highly active and their composition varies. Mainly, the composition of the leachate depends on factors such as characteristics of the waste, the moisture content, climatic conditions, degree of compaction and the age of the landfill. Therefore, the leachate composition cannot be generalized and the traditional treatment models should be adapted in each case. Although leachate composition is highly variable, what different leachates have in common is hazardous constituents and their potential eco-toxicological effects on human health and on terrestrial ecosystems. Since leachate has distinct compositions, each landfill or dumping site would represent a different type of risk on its environment. Nevertheless, leachates consist always of high organic concentration, conductivity, heavy metals and ammonia nitrogen. Leachate could affect the current and future quality of water bodies due to uncontrolled infiltrations. Therefore, control and treatment of leachate is one of the biggest issues in urban solid waste treatment plants and landfills design and management. This work presents a treatment model that will be carried out "in-situ" using a cost-effective novel technology that combines solar evaporation/condensation plus forward osmosis. The plant is powered by renewable energies (solar energy, biomass and residual heat), which will minimize the carbon footprint of the process. The final effluent quality is very high, allowing reuse (preferred) or discharge into watercourses. In the particular case of this work, the final effluents will be reused for cleaning and gardening purposes. A minority semi-solid residual stream is also generated in the process. Due to its special composition (rich in metals and inorganic elements), this stream will be valorized in ceramic industries to improve the final products characteristics.
Abstract: The paper reveals the birth and evolution of the British precedent Rylands v. Fletcher that, once adopted on the other side of the Ocean (in United States), gave rise to a general clause of liability for abnormally dangerous activities recognized by the §20 of the American Restatements of the Law Third, Liability for Physical and Emotional Harm. The main goal of the paper was to analyze the development of the legal doctrine and of the case law posterior to the precedent together with the intent of the British judicature to leapfrog from the traditional rule contained in Rylands v. Fletcher to a general clause similar to that introduced in the United States and recently also on the European level. As it is well known, within the scope of tort law two different initiatives compete with the aim of harmonizing the European laws: European Group on Tort Law with its Principles of European Tort Law (hereinafter PETL) in which article 5:101 sets forth a general clause for strict liability for abnormally dangerous activities and Study Group on European Civil Code with its Common Frame of Reference (CFR) which promotes rather ad hoc model of listing out determined cases of strict liability. Very narrow application scope of the art. 5:101 PETL, restricted only to abnormally dangerous activities, stays in opposition to very broad spectrum of strict liability cases governed by the CFR. The former is a perfect example of a general clause that offers a minimum and basic standard, possibly acceptable also in those countries in which, like in the United Kingdom, this regime of liability is completely marginalized.
Abstract: This study investigates the impact of public healthcare facilities and socio-economic circumstances on the status of child health in Pakistan. The complete analysis is carried out in correspondence with fourth and sixth millennium development goals. Further, the health variables chosen are also inherited from targeted indicators of the mentioned goals (MDGs). Trends in the Human Opportunity Index (HOI) for both health inequalities and coverage are analyzed using the Pakistan Social and Living Standards Measurement (PLSM) data set for 2001-02 to 2012-13 at the national and provincial level. To reveal the relative importance of each circumstance in achieving the targeted values for child health, Shorrocks decomposition is applied on HOI. The annual point average growth rate of HOI is used to simulate the time period for the achievement of target set by MDGs and universal access also. The results indicate an improvement in HOI for a reduction in child mortality rates from 52.1% in 2001-02 to 67.3% in 2012-13, which confirms the availability of healthcare opportunities to a larger segment of society. Similarly, immunization against measles and other diseases such as Diphtheria, Polio, Bacillus Calmette-Guerin (BCG), and Hepatitis has also registered an improvement from 51.6% to 69.9% during the period of study at the national level. On a positive note, no gender disparity has been found for child health indicators and that health outcome is mostly affected by the parental and geographical features and availability of health infrastructure. However, the study finds that this achievement has been uneven across provinces. Pakistan is not only lagging behind in achieving its health goals, disappointingly with the current rate of health care provision, but it will take many additional years to achieve its targets.
Abstract: Non-Newtonian fluid properties can change the flow
behaviour significantly, its prediction is more difficult when thermal
effects come into play. Hence, the focal point of this work is the
wake flow behind a heated circular cylinder in the laminar vortex
shedding regime for thermo-viscous shear thinning fluids. In the case
of isothermal flows of Newtonian fluids the vortex shedding regime
is characterised by a distinct Reynolds number and an associated
Strouhal number. In the case of thermo-viscous shear thinning
fluids the flow regime can significantly change in dependence of
the temperature of the viscous wall of the cylinder. The Reynolds
number alters locally and, consequentially, the Strouhal number
globally. In the present CFD study the temperature dependence of
the Reynolds and Strouhal number is investigated for the flow of a
Carreau fluid around a heated cylinder. The temperature dependence
of the fluid viscosity has been modelled by applying the standard
Williams-Landel-Ferry (WLF) equation. In the present simulation
campaign thermal boundary conditions have been varied over a
wide range in order to derive a relation between dimensionless heat
transfer, Reynolds and Strouhal number. Together with the shear
thinning due to the high shear rates close to the cylinder wall
this leads to a significant decrease of viscosity of three orders of
magnitude in the nearfield of the cylinder and a reduction of two
orders of magnitude in the wake field. Yet the shear thinning effect
is able to change the flow topology: a complex K´arm´an vortex street
occurs, also revealing distinct characteristic frequencies associated
with the dominant and sub-dominant vortices. Heating up the cylinder
wall leads to a delayed flow separation and narrower wake flow,
giving lesser space for the sequence of counter-rotating vortices. This
spatial limitation does not only reduce the amplitude of the oscillating
wake flow it also shifts the dominant frequency to higher frequencies,
furthermore it damps higher harmonics. Eventually the locally heated
wake flow smears out. Eventually, the CFD simulation results of the
systematically varied thermal flow parameter study have been used
to describe a relation for the main characteristic order parameters.
Abstract: This paper is a qualitative case study analysis of the development of a fully online learning community of graduate students through arts-based community building activities. With increasing numbers and types of online learning spaces, it is incumbent upon educators to continue to push the edge of what best practices look like in digital learning environments. In digital learning spaces, instructors can no longer be seen as purveyors of content knowledge to be examined at the end of a set course by a final test or exam. The rapid and fluid dissemination of information via Web 3.0 demands that we reshape our approach to teaching and learning, from one that is content-focused to one that is process-driven. Rather than having instructors as formal leaders, today’s digital learning environments require us to share expertise, as it is the collective experiences and knowledge of all students together with the instructors that help to create a very different kind of learning community. This paper focuses on innovations pursued in a 36 hour 12 week graduate course in higher education entitled “Critical and Reflective Practice”. The authors chronicle their journey to developing a fully online learning community (FOLC) by emphasizing the elements of social, cognitive, emotional and digital spaces that form a moving interplay through the community. In this way, students embrace anywhere anytime learning and often take the learning, as well as the relationships they build and skills they acquire, beyond the digital class into real world situations. We argue that in order to increase student online engagement, pedagogical approaches need to stem from two primary elements, both creativity and critical reflection, that are essential pillars upon which instructors can co-design learning environments with students. The theoretical framework for the paper is based on the interaction and interdependence of Creativity, Intuition, Critical Reflection, Social Constructivism and FOLCs. By leveraging students’ embedded familiarity with a wide variety of technologies, this case study of a graduate level course on critical reflection in education, examines how relationships, quality of work produced, and student engagement can improve by using creative and imaginative pedagogical strategies. The authors examine their professional pedagogical strategies through the lens that the teacher acts as facilitator, guide and co-designer. In a world where students can easily search for and organize information as self-directed processes, creativity and connection can at times be lost in the digitized course environment. The paper concludes by posing further questions as to how institutions of higher education may be challenged to restructure their credit granting courses into more flexible modules, and how students need to be considered an important part of assessment and evaluation strategies. By introducing creativity and critical reflection as central features of the digital learning spaces, notions of best practices in digital teaching and learning emerge.
Abstract: Croatia has made large steps forward in the development of higher education over the past 10 years. Purposes and objectives of the tertiary education system are focused on the personal development of young people so that they obtain competences for employment on a flexible labour market. The most frequent tensions between the tertiary institutions and employers are complaints that the current tertiary education system still supplies students with an abundance of theoretical knowledge and not enough practical skills. Polytechnics and schools of professional higher education should deliver professional education and training that will satisfy the needs of their local communities. The 21st century sets demand on undergraduates as well as their lecturers to strive for the highest standards. The skills students acquire during their studies should serve the needs of their future professional careers. In this context, teaching English for Specific Purposes (ESP) presents an enormous challenge for teachers. They have to cope with teaching the language in classes with a large number of students, limitations of time, inadequate equipment and teaching material; most frequently, this leads to focusing on specialist vocabulary neglecting the development of skills and competences required for future employment. Globalization has transformed the labour market and set new standards a perspective employee should meet. When knowledge of languages is considered, new generic skills and competences are required. Not only skillful written and oral communication is needed, but also information, media, and technology literacy, learning skills which include critical and creative thinking, collaborating and communicating, as well as social skills. The aim of this paper is to evaluate the needs of two groups of ESP first year Undergraduate Professional Administrative Study students taking ESP as a mandatory course: 47 first-year Undergraduate Professional Administrative Study students, 21 first-year employed part-time Undergraduate Professional Administrative Study students and 30 graduates with a degree in Undergraduate Professional Administrative Study with various amounts of work experience. The survey adopted a quantitative approach with the aim to determine the differences between the groups in their perception of the four language skills and different areas of law, as well as getting the insight into students' satisfaction with the current course and their motivation for studying ESP. Their perceptions will be compared to the results of the questionnaire conducted among sector professionals in order to examine how they perceive the same elements of the ESP course content and to what extent it fits into their working environment. The results of the survey indicated that there is a strong correlation between acquiring work experience and the level of importance given to particular areas of law studied in an ESP course which is in line with our initial hypothesis. In conclusion, the results of the survey should help lecturers in re-evaluating and updating their ESP course syllabi.
Abstract: The catalytic oxidation of CO and volatile organic compounds (VOCs) is considered as one of the most efficient ways to reduce harmful emissions from various chemical industries. The effectiveness of gold-based catalysts for many reactions of environmental significance was proven during the past three decades. The aim of this work was to combine the favorable features of Au and Cu-Ce mixed oxides in the design of new catalytic materials of improved efficiency and economic viability for removal of air pollutants in waste gases from formaldehyde production. Supported oxides of copper and cerium with Cu: Ce molar ratio 2:1 and 1:5 were prepared by wet impregnation of g-alumina. Gold (2 wt.%) catalysts were synthesized by a deposition-precipitation method. Catalysts characterization was carried out by texture measurements, powder X-ray diffraction, temperature programmed reduction and electron paramagnetic resonance spectroscopy. The catalytic activity in the oxidation of CO, CH3OH and (CH3)2O was measured using continuous flow equipment with fixed bed reactor. Both Cu-Ce/alumina samples demonstrated similar catalytic behavior. The addition of gold caused significant enhancement of CO and methanol oxidation activity (100 % degree of CO and CH3OH conversion at about 60 and 140 oC, respectively). The composition of Cu-Ce mixed oxides affected the performance of gold-based samples considerably. Gold catalyst on Cu-Ce/γ-Al2O3 1:5 exhibited higher activity for CO and CH3OH oxidation in comparison with Au on Cu-Ce/γ-Al2O3 2:1. The better performance of Au/Cu-Ce 1:5 was related to the availability of highly dispersed gold particles and copper oxide clusters in close contact with ceria.
Abstract: Natural dyes, extracted from black carrot and bramble, were utilized as photosensitizers to prepare dye-sensitized solar cells (DSSCs). Spectrophotometric studies of the natural dyes in solution and on a titanium dioxide substrate were carried out in order to assess changes in the status of the dyes. The results show that the bathochromic shift is seen on the photo-electrode substrate. The chemical binding of the natural dyes at the surface photo-electrode were increased by the chelating effect of the Ti(IV) ions. The cyclic voltammetry results showed that all extracts are suitable to be performed in DSSCs. Finally, photochemical performance and stability of DSSCs based on natural dyes were studied. The DSSCs sensitized by black carrot extract have been reported to achieve up to Jsc=1.17 mAcm-2, Voc= 0.55 V, FF= 0.52, η=0.34%, whereas Bramble extract can obtain up to Jsc=2.24 mAcm-2, Voc= 0.54 V, FF= 0.57, η=0.71%. The power conversion efficiency was obtained from the mixed dyes in DSSCs. The power conversion efficiency of dye-sensitized solar cells using mixed Black carrot and Bramble dye is the average of the their efficiency in single DSSCs.
Abstract: The convergence rate of the least-mean-square (LMS)
algorithm deteriorates if the input signal to the filter is correlated.
In a system identification problem, this convergence rate can be
improved if the signal is white and/or if the system is sparse. We
recently proposed a sparse transform domain LMS-type algorithm
that uses a variable step-size for a sparse system identification.
The proposed algorithm provided high performance even if the
input signal is highly correlated. In this work, we investigate the
performance of the proposed TD-LMS algorithm for a large number
of filter tap which is also a critical issue for standard LMS algorithm.
Additionally, the optimum value of the most important parameter is
calculated for all experiments. Moreover, the convergence analysis
of the proposed algorithm is provided. The performance of the
proposed algorithm has been compared to different algorithms in a
sparse system identification setting of different sparsity levels and
different number of filter taps. Simulations have shown that the
proposed algorithm has prominent performance compared to the other
algorithms.
Abstract: This paper aims to analyse how Ian Hacking states the
theoretical basis of his research on the classification of people.
Although all his early philosophical education had been based in
Foucault, it is also true that Erving Goffman’s perspective provided
him with epistemological and methodological tools for understanding
face-to-face relationships. Hence, all his works must be thought of as
social science texts that combine the research on how the individuals
are constituted ‘top-down’ (as in Foucault), with the inquiry into how
people renegotiate ‘bottom-up’ the classifications about them. Thus,
Hacking´s proposal constitutes a middle ground between the French
Philosopher and the American Sociologist. Placing himself between
both authors allows Hacking to build a frame that is expected to
adjust to Social Sciences’ main particularity: the fact that they study
interactive kinds. These are kinds of people, which imply that those
who are classified can change in certain ways that prompt the need
for changing previous classifications themselves. It is all about the
interaction between the labelling of people and the people who are
classified. Consequently, understanding the way in which Hacking
uses Foucault’s and Goffman’s theories is essential to fully
comprehend the social dynamic between individuals and concepts,
what Bert Hansen had called dialectical realism. His theoretical
proposal, therefore, is not only valuable because it combines diverse
perspectives, but also because it constitutes an utterly original and
relevant framework for Sociological theory and particularly for
Criminology.
Abstract: The purification of brackish seawater becomes a necessity and not a choice against demographic and industrial growth especially in third world countries. Two models can be used in this work: simple solar still and simple solar still coupled with a heat pump. In this research, the productivity of water by Simple Solar Distiller (SSD) and Simple Solar Distiller Hybrid Heat Pump (SSDHP) was determined by the orientation, the use of heat pump, the simple or double glass cover. The productivity can exceed 1.2 L/m²h for the SSDHP and 0.5 L/m²h for SSD model. The result of the global efficiency is determined for two models SSD and SSDHP give respectively 30%, 50%. The internal efficiency attained 35% for SSD and 60% of the SSDHP models. Convective heat coefficient can be determined by attained 2.5 W/m²°C and 0.5 W/m²°C respectively for SSDHP and SSD models.
Abstract: A total of 100 primary caregivers (mothers, fathers, grandparents) with at least one child or grandchild with a diagnosis of congenital bilateral profound deafness were assessed in order to evaluate the functionality of families with a deaf member, who was evaluated by specialists in audiology, molecular biology, genetics and psychology. After confirmation of the clinical diagnosis, DNA from the patients and parents were analyzed in search of the 35delG deletion of the GJB2 gene to determine who possessed the mutation. All primary caregivers were provided psychological support, regardless of whether or not they had the mutation, and prior and subsequent, the family APGAR test was applied. All parents, grandparents were informed of the results of the genetic analysis during the psychological intervention. The family APGAR, after psychological and genetic counseling, showed that 14% perceived their families as functional, 62% moderately functional and 24% dysfunctional. This shows the importance of psychological support in family functionality that has a direct impact on the quality of life of these families.