Abstract: Undoubtedly, chassis is one of the most important
parts of a vehicle. Chassis that today are produced for vehicles are
made up of four parts. These parts are jointed together by screwing.
Transverse parts are called cross member.
This study reviews the stress generated by cyclic laboratory loads
in front cross member of Peugeot 405. In this paper the finite element
method is used to simulate the welding process and to determine the
physical response of the spot-welded joints. Analysis is done by the
Abaqus software.
The Stresses generated in cross member structure are generally
classified into two groups: The stresses remained in form of residual
stresses after welding process and the mechanical stress generated by
cyclic load. Accordingly the total stress must be obtained by
determining residual stress and mechanical stress separately and then
sum them according to the superposition principle.
In order to improve accuracy, material properties including
physical, thermal and mechanical properties were supposed to be
temperature-dependent. Simulation shows that maximum Von Misses
stresses are located at special points. The model results are then
compared to the experimental results which are reported by
producing factory and good agreement is observed.
Abstract: The fundamental defect inherent to the thermoforming
technology is wall-thickness variation of the products due to
inadequate thermal processing during production of polymer. A
nonlinear viscoelastic rheological model is implemented for
developing the process model. This model describes deformation
process of a sheet in thermoforming process. Because of relaxation
pause after plug-assist stage and also implementation of two stage
thermoforming process have minor wall-thickness variation and
consequently better mechanical properties of polymeric articles. For
model validation, a comparative analysis of the theoretical and
experimental data is presented.
Abstract: Bone remodeling occurs by the balanced action of
bone resorbing osteoclasts (OC) and bone-building osteoblasts.
Increased bone resorption by excessive OC activity contributes
to malignant and non-malignant diseases including osteoporosis.
To study OC differentiation and function, OC formed in
in vitro cultures are currently counted manually, a tedious
procedure which is prone to inter-observer differences. Aiming
for an automated OC-quantification system, classification of
OC and precursor cells was done on fluorescence microscope
images based on the distinct appearance of fluorescent nuclei.
Following ellipse fitting to nuclei, a combination of eight
features enabled clustering of OC and precursor cell nuclei.
After evaluating different machine-learning techniques, LOGREG
achieved 74% correctly classified OC and precursor cell
nuclei, outperforming human experts (best expert: 55%). In
combination with the automated detection of total cell areas,
this system allows to measure various cell parameters and most
importantly to quantify proteins involved in osteoclastogenesis.
Abstract: Subdivision is a method to create a smooth surface from a coarse mesh by subdividing the entire mesh. The conventional ways to compute and render surfaces are inconvenient both in terms of memory and computational time as the number of meshes will increase exponentially. An adaptive subdivision is the way to reduce the computational time and memory by subdividing only certain selected areas. In this paper, a new adaptive subdivision method for triangle meshes is introduced. This method defines a new adaptive subdivision rules by considering the properties of each triangle's neighbors and is embedded in a traditional Loop's subdivision. It prevents some undesirable side effects that appear in the conventional adaptive ways. Models that were subdivided by our method are compared with other adaptive subdivision methods
Abstract: This paper presents a unified approach based graph
theory and system theory postulates for the modeling and analysis
of Simple open cycle Gas turbine system. In the present paper, the
simple open cycle gas turbine system has been modeled up to its subsystem
level and system variables have been identified to develop the
process subgraphs. The theorems and algorithms of the graph theory
have been used to represent behavioural properties of the system like
rate of heat and work transfers rates, pressure drops and temperature
drops in the involved processes of the system. The processes have
been represented as edges of the process subgraphs and their limits
as the vertices of the process subgraphs. The system across variables
and through variables has been used to develop terminal equations of
the process subgraphs of the system. The set of equations developed
for vertices and edges of network graph are used to solve the system
for its process variables.
Abstract: In this paper, a new technique for fast painting with
different colors is presented. The idea of painting relies on applying
masks with different colors to the background. Fast painting is
achieved by applying these masks in the frequency domain instead of
spatial (time) domain. New colors can be generated automatically as a
result from the cross correlation operation. This idea was applied
successfully for faster specific data (face, object, pattern, and code)
detection using neural algorithms. Here, instead of performing cross
correlation between the input input data (e.g., image, or a stream of
sequential data) and the weights of neural networks, the cross
correlation is performed between the colored masks and the
background. Furthermore, this approach is developed to reduce the
computation steps required by the painting operation. The principle of
divide and conquer strategy is applied through background
decomposition. Each background is divided into small in size subbackgrounds
and then each sub-background is processed separately by
using a single faster painting algorithm. Moreover, the fastest painting
is achieved by using parallel processing techniques to paint the
resulting sub-backgrounds using the same number of faster painting
algorithms. In contrast to using only faster painting algorithm, the
speed up ratio is increased with the size of the background when using
faster painting algorithm and background decomposition. Simulation
results show that painting in the frequency domain is faster than that in
the spatial domain.
Abstract: The aim of this work was to investigate the potential of soil microorganisms and the burhead plant, as well as the combination of soil microorganisms and plants to remediate monoethylene glycol (MEG), diethylene glycol (DEG), and triethylene glycol (TEG) in synthetic wastewater. The result showed that a system containing both burhead plant and soil microorganisms had the highest efficiency in EGs removal. Around 100% of MEG and DEG and 85% of TEG were removed within 15 days of the experiments. However, the burhead plant had higher removal efficiency than soil microorganisms for MEG and DEG but the same for TEG in the study systems. The removal rate of EGs in the study system related to the molecular weight of the compounds and MEG, the smallest glycol, was removed faster than DEG and TEG by both the burhead plant and soil microorganisms in the study system.
Abstract: A satellite is being integrated and tested by BISEE (Beijing Institute of Spacecraft Environment Engineering). This paper describes the infrared lamp array simulation technology used for satellite thermal balance and thermal vacuum test. These tests were performed in KM6 space environmental simulator in Beijing, China. New software and hardware developed by BISEE, along with enhanced heat flux uniformity, provided for well accomplished thermal balance and thermal vacuum tests. The flux uniformity of lamp array was satisfied with test requirement. Monitored background radiometer offered reliable heat flux measurements with remarkable repeatability. Simulation software supplied accurate thermal flux distribution predictions.
Abstract: The rheological properties, structure and potential synergistic interactions of whey proteins (1-6%) and inulin (20%) in mixed gels in the presence of CaCl2 was the aim of this study. Whey proteins have a strong influence on inulin gel formation. At low concentrations (2%) whey proteins did not impair in inulin gel formation. At higher concentration (4%) whey proteins impaired inulin gelation and inulin impaired the formation of a Ca2+-induced whey protein network. The presence of whey proteins at a level allowing for protein gel network formation (6%) significantly increased the rheological parameters values of the gels. SEM micrographs showed that whey protein structure was coated by inulin moieties which could make the mixed gels firmer. The protein surface hydrophobicity measurements did not exclude synergistic interactions between inulin and whey proteins, however. The use of an electrophoretic technique did not show any stable inulin-whey protein complexes.
Abstract: The present paper proposes high performance nonlinear
force controllers for a servopneumatic real-time fatigue test
machine. A CompactRIO® controller was used, being fully
programmed using LabVIEW language. Fuzzy logic control
algorithms were evaluated to tune the integral and derivative
components in the development of hybrid controllers, namely a FLC
P and a hybrid FLC PID real-time-based controllers. Their
behaviours were described by using state diagrams. The main
contribution is to ensure a smooth transition between control states,
avoiding discrete transitions in controller outputs. Steady-state errors
lower than 1.5 N were reached, without retuning the controllers.
Good results were also obtained for sinusoidal tracking tasks from
1/¤Ç to 8/¤Ç Hz.
Abstract: The resident registration number was adopted for the purposes of enhanced services for resident convenience and effective performance of governmental administrative affairs. However, it has been used for identification purposes customarily and irrationally in line with the development and spread of the Internet. In response to the growing concern about the leakage of collected RRNs and possible abuses of stolen RRNs, e.g. identity theft, for crimes, the Korean Communications Commission began to take legal/regulatory actions in 2011 to minimize the online collection and use of resident registration numbers. As the use of the RRN was limited after the revision of the Act on Promotion of Information and Communications Network Utilization and Information Protection, etc., online business providers were required to have alternatives to the RRN for the purpose of identifying the user's identity and age, in compliance with the law, and settling disputes with customers. This paper presents means of verifying the personal identity by taking advantage of the commonly used infrastructure and simply replacing personal information entered and stored, without requiring users to enter their RRNs.
Abstract: Actual load, material characteristics and other
quantities often differ from the design values. This can cause worse
function, shorter life or failure of a civil engineering structure, a
machine, vehicle or another appliance. The paper shows main causes
of the uncertainties and deviations and presents a systematic
approach and efficient tools for their elimination or mitigation of
consequences. Emphasis is put on the design stage, which is most
important for reliability ensuring. Principles of robust design and
important tools are explained, including FMEA, sensitivity analysis
and probabilistic simulation methods. The lifetime prediction of
long-life objects can be improved by long-term monitoring of the
load response and damage accumulation in operation. The condition
evaluation of engineering structures, such as bridges, is often based
on visual inspection and verbal description. Here, methods based on
fuzzy logic can reduce the subjective influences.
Abstract: Artificial Neural Network (ANN) has been
extensively used for classification of heart sounds for its
discriminative training ability and easy implementation. However, it
suffers from overparameterization if the number of nodes is not
chosen properly. In such cases, when the dataset has redundancy
within it, ANN is trained along with this redundant information that
results in poor validation. Also a larger network means more
computational expense resulting more hardware and time related
cost. Therefore, an optimum design of neural network is needed
towards real-time detection of pathological patterns, if any from heart
sound signal. The aims of this work are to (i) select a set of input
features that are effective for identification of heart sound signals and
(ii) make certain optimum selection of nodes in the hidden layer for a
more effective ANN structure. Here, we present an optimization
technique that involves Singular Value Decomposition (SVD) and
QR factorization with column pivoting (QRcp) methodology to
optimize empirically chosen over-parameterized ANN structure.
Input nodes present in ANN structure is optimized by SVD followed
by QRcp while only SVD is required to prune undesirable hidden
nodes. The result is presented for classifying 12 common
pathological cases and normal heart sound.
Abstract: A finite element analysis (FEA) computer software HyperWorks is utilized in re-designing an automotive component to reduce its mass. Reduction of components mass contributes towards environmental sustainability by saving world-s valuable metal resources and by reducing carbon emission through improved overall vehicle fuel efficiency. A shape optimization analysis was performed on a rear spindle component. Pre-processing and solving procedures were performed using HyperMesh and RADIOSS respectively. Shape variables were defined using HyperMorph. Then optimization solver OptiStruct was utilized with fatigue life set as a design constraint. Since Stress-Number of Cycle (S-N) theory deals with uni-axial stress, the Signed von Misses stress on the component was used for looking up damage on S-N curve, and Gerber criterion for mean stress corrections. The optimization analysis resulted in mass reduction of 24% of the original mass. The study proved that the adopted approach has high potential use for environmental sustainability.
Abstract: In gas lifted oil fields, the lift gas should be distributed optimally among the wells which share gas from a common source to maximize total oil production. One of the objectives of the paper is to show that a linear MPC consisting of a control objective and an economic objective can be used both as an optimizer and a controller for gas lifted systems. The MPC is based on linearized model of the oil field developed from first principles modeling. Simulation results show that the total oil production is increased by 3.4%. Difficulties in accurately measuring the bottom hole pressure using sensors in harsh operating conditions can be resolved by using an Unscented Kalman Filter (UKF) for estimation. In oil fields where input disturbance (total supply of gas) is not measured, UKF can also be used for disturbance estimation. Increased total oil production due to optimization leads to increased profit.
Abstract: In this paper, we propose a chaotic cipher system consisting of Improved Volterra Filters and the mapping that is created from the actual voice by using Radial Basis Function Network. In order to achieve a practical system, the system supposes to use the digital communication line, such as the Internet, to maintain the parameter matching between the transmitter and receiver sides. Therefore, in order to withstand the attack from outside, it is necessary that complicate the internal state and improve the sensitivity coefficient. In this paper, we validate the robustness of proposed method from three perspectives of "Chaotic properties", "Randomness", "Coefficient sensitivity".
Abstract: For the last decade, statistics show traumatic brain
injury (TBI) is a growing concern in our legal system. In an effort to
obtain data regarding the influence of neuropsychological expert
witness testimony in a criminal case, this study tested three
hypotheses. H1: The majority of jurors will vote not guilty, due to
mild head injury. H2: The jurors will give more credence to the
testimony of the neuropsychologist rather than the psychiatrist. H3:
The jurors will be more lenient in their sentencing, given the
testimony of the neuropsychologist-s testimony. The criterion for
inclusion in the study as a participant is identical to those used for
inclusion in the eligibility for jury duty in the United States. A chisquared
test was performed to analyze the data for the three
hypotheses. The results supported all of the hypotheses; however
statistical significance was seen in H1 and H2 only.
Abstract: In the paper, the results of sensitivity analysis of the influence of initial imperfections on the web stress state of a thinwalled girder are presented. The results of the study corroborate a very good and effective agreement of experiments with theory. Most input random quantities were found experimentally. The change of sensitivity coefficients in dependence on working load value is analysed. The stress was analysed by means of a geometrically and materially non-linear solution by applying the program ANSYS. This research study offers important background for theoretical studies of stability problems, post-critical effects and limit states of thin-walled steel structures.
Abstract: In this paper a non-parametric statistical pattern recognition algorithm for the problem of credit scoring will be presented. The proposed algorithm is based on a clustering k- means algorithm and allows for the determination of subclasses of homogenous elements in the data. The algorithm will be tested on two benchmark datasets and its performance compared with other well known pattern recognition algorithm for credit scoring.
Abstract: Despite the fact that B2c eCommerce has become
important in numerous economies, its adoption varies from country to
country. This paper aims to identify the factors affecting (enabling or
inhibiting) B2c eCommerce and to determine their quantitative
impact on the diffusion of online sales across countries. A dynamic
panel model analyzing the relationship between 13 factors
(Macroeconomic, Demographic, Socio-Cultural, Infrastructural and
Offer related) stemming from a complete literature analysis and the
B2c eCommerce value in 45 countries over 9 years has been
developed. Having a positive correlation coefficient, GDP, mobile
penetration, Internet user penetration and credit card penetration
resulted as enabling drivers of the B2c eCommerce value across
countries, whereas, having a negative correlation coefficient,equal
distribution of income and the development of traditional retailing
network act as inhibiting factors.