Abstract: A dent is a gross distortion of the pipe cross-section.
Dent depth is defined as the maximum reduction in the diameter of
the pipe compared to the original diameter. Pipeline dent finite
element (FE) simulation and theoretical analysis are conducted in this
paper to develop an understanding of the geometric characteristics
and strain distribution in the pressurized dented pipe. Based on the
results, the magnitude of the denting force increases significantly
with increasing the internal pressure, and the maximum
circumferential and longitudinal strains increase by increasing the
internal pressure and the dent depth. The results can be used for
characterizing dents and ranking their risks to the integrity of a
pipeline.
Abstract: As an economic and safe structure, Bi-steel is widely
used in reinforced concrete with less consumption of steel. In this
paper, III Bi-steel concrete beam has been analyzed. Through careful
observation and theoretical analysis, the new calculating formulae for
structural rigidity and crack have been formulated for this Bi-steel
concrete beam. And structural rigidity and the crack features have also
been theoretically analyzed.
Abstract: This paper deals with the development of a Jacobean model for a 4-axes indigenously developed scara robot arm in the laboratory. This model is used to study the relation between the velocities and the forces in the robot while it is doing the pick and place operation.
Abstract: The Aggregate Production Plan (APP) is a schedule of
the organization-s overall operations over a planning horizon to
satisfy demand while minimizing costs. It is the baseline for any
further planning and formulating the master production scheduling,
resources, capacity and raw material planning. This paper presents a
methodology to model the Aggregate Production Planning problem,
which is combinatorial in nature, when optimized with Genetic
Algorithms. This is done considering a multitude of constraints of
contradictory nature and the optimization criterion – overall cost,
made up of costs with production, work force, inventory, and
subcontracting. A case study of substantial size, used to develop the
model, is presented, along with the genetic operators.
Abstract: A total of fourteen slab-edge beam-column connection specimens were tested gradually to failure under the effect of simultaneous action of shear force and moment. The objective was to investigate the influence of some parameters thought to be important on the behavior and strength of slab-column connections with edge beams encountered in flat slab flooring and roofing systems. The parameters included the existence and strength of edge beam, depth and width of edge beam, steel reinforcement ratio of slab, ratio of moment to shear force, and the existence of openings in the region next to the column.
Results obtained demonstrated the importance of the studied parameters on the strength and behavior of slab-column connections with edge beams.
Abstract: The primary purpose of this article is an attempt to
find the implication of globalization on education. Globalization has
an important role as a process in the economical, political, cultural
and technological dimensions in the life of the contemporary human
being and has been affected by it. Education has its effects in this
procedure and while influencing it through educating global citizens
having universal human features and characteristics, has been
influenced by this phenomenon too. Nowadays, the role of education
is not just to develop in the students the knowledge and skills
necessary for the new kinds of jobs. If education wants to help
students be prepared of the new global society, it has to make them
engaged productive and critical citizens for the global era, so that
they can reflect about their roles as key actors in a dynamic often
uneven, matrix of economic and cultural exchanges. If education
wants to reinforce and raise the national identity, the value system
and the children and teenagers, it should make them ready for living
in the global era of this century. The used method in this research is
documentary and analyzing the documents. Studies in this field show
globalization has influences on the processes of the production,
distribution and consuming of knowledge. The happening of this
event in the information era has not only provide the necessary
opportunities for the exchanges of education worldwide but also has
privileges for the developing countries which enables them to
strengthen educational bases of their society and have an important
step toward their future.
Abstract: The aim of present experiment was to evaluate the
influence of cultivar to quality parameters of dried potato chips and
sticks produced in microwave-vacuum drier. The potatoes before
drying were blanched in oil and water at 180ºC and at 85ºC
respectively. The moisture content, crispiness, the colour (CIE
L*a*b*), the content of ascorbic acid, total carotenoids and total fat
content of dried potato chips and sticks was determined The highest
ascorbic acid content, high content of carotenoids, low total fat
content, low acrylamide content and good crispiness (low breaking
force) especially for sticks was determined in the samples of Gundega
cultivar.
Abstract: Twist drills are geometrical complex tools and thus various researchers have adopted different mathematical and experimental approaches for their simulation. The present paper acknowledges the increasing use of modern CAD systems and using the API (Application Programming Interface) of a CAD system, drilling simulations are carried out. The developed DRILL3D software routine, creates parametrically controlled tool geometries and using different cutting conditions, achieves the generation of solid models for all the relevant data involved (drilling tool, cut workpiece, undeformed chip). The final data derived, consist a platform for further direct simulations regarding the determination of cutting forces, tool wear, drilling optimizations etc.
Abstract: In Algeria, liberalization reforms undertaken since the 1990s have resulted in negative effects on the development and management of irrigation schemes, as well as on the conditions of farmers. Reforms have been undertaken to improve the performance of irrigation schemes, such as the national plan of agricultural development (PNDA) in 2000 and the water pricing policy of 2005. However, after implementation of these policies, questions have arisen with regard to irrigation performance and its suitability for agricultural development. Hence, the aim of this paper is to provide insight into the profitability of irrigation during the transition period under current irrigation agricultural policies in Algeria. By using the method of farm crop budget analysis in the East Mitidja irrigation scheme, the returns from using surface water resources based on farm typology were found to vary among crops and farmers- groups within the scheme. Irrigation under the current situation is profitable for all farmers, including both those who benefit from subsidies and those who do not. However, the returns to water were found to be very sensitive to crop price fluctuations, particularly for non-subsidized groups and less so for those whose farming is based on orchards. Moreover, the socio-economic environment of the farmers contributed to less significant impacts of the PNDA policy. In fact, the limiting factor is not only the water, but also the lack of land ownership title. Market access constraints led to less agricultural investment and therefore to low intensification and low water productivity. It is financially feasible to recover the annual O&M costs in the irrigation scheme. By comparing the irrigation water price, returns to water, and O&M costs of water delivery, it is clear that irrigation can be profitable in the future. However, water productivity must be improved by enhancing farmers- income through farming investment, improving assets access, and the allocation of activities and crops which bring high returns to water; this could allow the farmers to pay more for water and allow cost recovery for water systems.
Abstract: The review performed on the condition of energy
consumption & rate in Iran, shows that unfortunately the subject of
optimization and conservation of energy in active industries of
country lacks a practical & effective method and in most factories,
the energy consumption and rate is more than in similar industries of
industrial countries. The increasing demand of electrical energy and
the overheads which it imposes on the organization, forces
companies to search for suitable approaches to optimize energy
consumption and demand management. Application of value
engineering techniques is among these approaches. Value
engineering is considered a powerful tool for improving profitability.
These tools are used for reduction of expenses, increasing profits,
quality improvement, increasing market share, performing works in
shorter durations, more efficient utilization of sources & etc.
In this article, we shall review the subject of value engineering and
its capabilities for creating effective transformations in industrial
organizations, in order to reduce energy costs & the results have
been investigated and described during a case study in Mazandaran
wood and paper industries, the biggest consumer of energy in north
of Iran, for the purpose of presenting the effects of performed tasks
in optimization of energy consumption by utilizing value engineering
techniques in one case study.
Abstract: It is impossible to think about democracy without elections. The litmus test of any electoral process in any country is the possibility of a one time minority to become a majority at another time and a peaceful transition of power. In many countries in Sub-Saharan Africa though the multi-party elections appeared to be competitive they failed the acid test of democracy: peaceful regime change in a free and fair election. Failure to solve electoral disputes might lead to bloody electoral conflicts as witnessed in many emerging democracies in Africa. The aim of this paper is to investigate electoral conflicts in Africa since the end of the Cold War by using the 2005 post-election violence in Ethiopia as a case study. In Ethiopia, the coming to power of the EPRDF in 1991 marked the fall of the Derg dictatorial military government and the beginning of a multi-party democracy. The country held multi-party parliamentary elections in 1995, 2000, and 2005 where the ruling EPRDF party “won" the elections through violence, involving intimidation, manipulation, detentions of political opponents, torture, and political assassinations. The 2005 electoral violence was the worst electoral violence in the country-s political history that led to the death of 193 protestors and the imprisonment of more than 40, 000 people. It is found out that the major causes of the 2005 Ethiopian election were the defeat of the ruling party in the election and its attempt to reverse the poll results by force; the Opposition-s lack of decisive leadership; the absence of independent courts and independent electoral management body; and the ruling party-s direct control over the army and police.
Abstract: A series of tests on cold-formed steel (CFS) wall plate system subjected to uplift force at the mid span of the wall plate is presented. The aim of the study was to study the behaviour and identify the modes of failure of CFS wall plate system. Two parameters were considered in these studies: 1) different dimension of U-bracket at the supports and 2) different sizes of lipped C-channel. The lipped C-channels used were C07508, C07512 and C10012. The dimensions of the leg of U-bracket were 50x35 mm and 50x60 mm respectively, where 25 mm clearance was provided to the connections for specimens with clearance. Results show that specimens with and without clearance experienced the same mode of failure. Failure began with the yielding of the connectors followed by distortional buckling of the wall plate. However, when C075 sections were used as wall plate, the system behaved differently. There was a large deformation in the wall plate and failure began in the distortional buckling of the wall plate followed by bearing of the connecting plates at the supports (U-bracket). The ultimate strength of the system also decreased dramatically when C075 sections were used.
Abstract: This paper presents an advance in monitoring and
process control of surface roughness in CNC machine for the turning
and milling processes. An integration of the in-process monitoring
and process control of the surface roughness is proposed and
developed during the machining process by using the cutting force
ratio. The previously developed surface roughness models for turning
and milling processes of the author are adopted to predict the inprocess
surface roughness, which consist of the cutting speed, the
feed rate, the tool nose radius, the depth of cut, the rake angle, and
the cutting force ratio. The cutting force ratios obtained from the
turning and the milling are utilized to estimate the in-process surface
roughness. The dynamometers are installed on the tool turret of CNC
turning machine and the table of 5-axis machining center to monitor
the cutting forces. The in-process control of the surface roughness
has been developed and proposed to control the predicted surface
roughness. It has been proved by the cutting tests that the proposed
integration system of the in-process monitoring and the process
control can be used to check the surface roughness during the cutting
by utilizing the cutting force ratio.
Abstract: One of the main advantages of the LO paradigm is to
allow the availability of good quality, shareable learning material
through the Web. The effectiveness of the retrieval process requires a
formal description of the resources (metadata) that closely fits the
user-s search criteria; in spite of the huge international efforts in this
field, educational metadata schemata often fail to fulfil this
requirement. This work aims to improve the situation, by the
definition of a metadata model capturing specific didactic features of
shareable learning resources. It classifies LOs into “teacher-oriented"
and “student-oriented" categories, in order to describe the role a LO
is to play when it is integrated into the educational process. This
article describes the model and a first experimental validation process
that has been carried out in a controlled environment.
Abstract: The previous study of new metal gasket that contact
width and contact stress an important design parameter for optimizing
metal gasket performance. The optimum design based on an elastic
and plastic contact stress was founded. However, the influence of
flange surface roughness had not been investigated thoroughly. The
flange has many kinds of surface roughness. In this study, we
conducted a gasket model include a flange surface roughness effect. A
finite element method was employed to develop simulation solution. A
uniform quadratic mesh used for meshing the gasket material and a
gradually quadrilateral mesh used for meshing the flange. The gasket
model was simulated by using two simulation stages which is forming
and tightening simulation. A simulation result shows that a smoother
of surface roughness has higher slope for force per unit length. This
mean a squeezed against between flange and gasket will be strong. The
slope of force per unit length for gasket 400-MPa mode was higher
than the gasket 0-MPa mode.
Abstract: This paper presents a several diagnostic methods designed to electrical machinesespecially for permanent magnets (PM) machines. Those machines are commonly used in small wind and water systems and vehicles drives.Thosemethodsare preferred by the author in periodic diagnostic of electrical machines. The special attentionshould be paid to diagnostic method of turn-to-turn insulation and vibrations. Both of those methodswere createdinInstitute of Electrical Drives and MachinesKomel. The vibration diagnostic method is the main thesis of author’s doctoral dissertation. This is method of determination the technical condition of PM electrical machine basing on its own signals is the subject of patent application No P.405669. Specific structural properties of machines excited by permanent magnets are used in this method - electromotive force (EMF) generated due to vibrations. There was analysed number of publications which describe vibration diagnostic methods and tests of electrical machines with permanent magnets and there was no method found to determine the technical condition of such machine basing on their own signals.
Abstract: Chlorine is one of the most abundant elements in
nature, which undergoes a complex biogeochemical cycle. Chlorine
bound in some substances is partly responsible for atmospheric ozone
depletion and contamination of some ecosystems. As due to
international regulations anthropogenic burden of volatile
organochlorines (VOCls) in atmosphere decreases, natural sources
(plants, soil, abiotic formation) are expected to dominate VOCl
production in the near future. Examples of plant VOCl production are
methyl chloride, and bromide emission from (sub)tropical ferns,
chloroform, 1,1,1-trichloroethane and tetrachloromethane emission
from temperate forest fern and moss. Temperate forests are found to
emit in addition to the previous compounds tetrachloroethene, and
brominated volatile compounds. VOCls can be taken up and further
metabolized in plants. The aim of this work is to identify and
quantitatively analyze the formed VOCls in temperate forest
ecosystems by a cryofocusing/GC-ECD detection method, hence
filling a gap of knowledge in the biogeochemical cycle of chlorine.
Abstract: In this paper, the details of an experimental method to measure the clamping force value at bolted connections due to application of wrenching torque to tighten the nut have been presented. A simplified bolted joint including a holed plate with a single bolt was considered to carry out the experiments. This method was designed based on Hooke-s law by measuring compressive axial strain of a steel bush placed between the nut and the plate. In the experimental procedure, the values of clamping force were calculated for seven different levels of applied torque, and this process was repeated three times for each level of the torque. Moreover, the effect of lubrication of threads on the clamping value was studied using the same method. In both conditions (dry and lubricated threads), relation between the torque and the clamping force have been displayed in graphs.
Abstract: Inorganic nanoparticles filled polymer composites
have extended their multiple functionalities to various applications,
including mechanical reinforcement, gas barrier, dimensional
stability, heat distortion temperature, flame-retardant, and thermal
conductivity. Sodium stearate-modified calcium carbonate (CaCO3)
nanoparticles were prepared using surface modification method. The
results showed that sodium stearate attached to the surface of CaCO3
nanoparticles with the chemical bond. The effect of modified CaCO3
nanoparticles on thermal properties of polypropylene (PP) was
studied by means of differential scanning calorimetry (DSC) and
Thermogravimetric analysis (TGA). It was found that CaCO3
significantly affected the crystallization temperature and
crystallization degree of PP. Effect of the modified CaCO3 content on
mechanical properties of PP/CaCO3 nanocomposites was also
studied. The results showed that the modified CaCO3 can effectively
improve the mechanical properties of PP. In comparison with PP, the
impact strength of PP/CaCO3 nanocomposites increased by about
65% and the hardness increased by about 5%.
Abstract: Concrete strength evaluated from compression tests
on cores is affected by several factors causing differences from the
in-situ strength at the location from which the core specimen was
extracted. Among the factors, there is the damage possibly occurring
during the drilling phase that generally leads to underestimate the
actual in-situ strength. In order to quantify this effect, in this study
two wide datasets have been examined, including: (i) about 500 core
specimens extracted from Reinforced Concrete existing structures,
and (ii) about 600 cube specimens taken during the construction of
new structures in the framework of routine acceptance control. The
two experimental datasets have been compared in terms of
compression strength and specific weight values, accounting for the
main factors affecting a concrete property, that is type and amount of
cement, aggregates' grading, type and maximum size of aggregates,
water/cement ratio, placing and curing modality, concrete age. The
results show that the magnitude of the strength reduction due to
drilling damage is strongly affected by the actual properties of
concrete, being inversely proportional to its strength. Therefore, the
application of a single value of the correction coefficient, as generally
suggested in the technical literature and in structural codes, appears
inappropriate. A set of values of the drilling damage coefficient is
suggested as a function of the strength obtained from compressive
tests on cores.