Abstract: Phase locked loops for data links operating at 10 Gb/s
or faster are low phase noise devices designed to operate with a low
jitter reference clock. Characterization of their jitter transfer function
is difficult because the intrinsic noise of the device is comparable to
the random noise level in the reference clock signal. A linear model
is proposed to account for the intrinsic noise of a PLL. The intrinsic
noise data of a PLL for 10 Gb/s links is presented. The jitter transfer
function of a PLL in a test chip for 12.8 Gb/s data links was
determined in experiments using the 400 MHz reference clock as the
source of simultaneous excitations over a wide range of frequency.
The result shows that the PLL jitter transfer function can be
approximated by a second order linear model.
Abstract: In the traditional theory of non-uniform torsion the
axial displacement field is expressed as the product of the unit twist
angle and the warping function. The first one, variable along the
beam axis, is obtained by a global congruence condition; the second
one, instead, defined over the cross-section, is determined by solving
a Neumann problem associated to the Laplace equation, as well as for
the uniform torsion problem.
So, as in the classical theory the warping function doesn-t punctually
satisfy the first indefinite equilibrium equation, the principal aim of
this work is to develop a new theory for non-uniform torsion of
beams with axial symmetric cross-section, fully restrained on both
ends and loaded by a constant torque, that permits to punctually
satisfy the previous equation, by means of a trigonometric expansion
of the axial displacement and unit twist angle functions.
Furthermore, as the classical theory is generally applied with good
results to the global and local analysis of ship structures, two beams
having the first one an open profile, the second one a closed section,
have been analyzed, in order to compare the two theories.
Abstract: Power-line networks are widely used today for broadband data transmission. However, due to multipaths within the broadband power line communication (BPLC) systems owing to stochastic changes in the network load impedances, branches, etc., network or channel capacity performances are affected. This paper attempts to investigate the performance of typical medium voltage channels that uses Orthogonal Frequency Division Multiplexing (OFDM) techniques with Quadrature Amplitude Modulation (QAM) sub carriers. It has been observed that when the load impedances are different from line characteristic impedance channel performance decreases. Also as the number of branches in the link between the transmitter and receiver increases a loss of 4dB/branch is found in the signal to noise ratio (SNR). The information presented in the paper could be useful for an appropriate design of the BPLC systems.
Abstract: Connected dominating set (CDS) problem in unit disk
graph has signi£cant impact on an ef£cient design of routing protocols
in wireless sensor networks, where the searching space for a
route is reduced to nodes in the set. A set is dominating if all the
nodes in the system are either in the set or neighbors of nodes in the
set. In this paper, a simple and ef£cient heuristic method is proposed
for £nding a minimum connected dominating set (MCDS) in ad hoc
wireless networks based on the new parameter support of vertices.
With this parameter the proposed heuristic approach effectively
£nds the MCDS of a graph. Extensive computational experiments
show that the proposed approach outperforms the recently proposed
heuristics found in the literature for the MCD
Abstract: This paper presents an idea to improve the efficiency
of security checks in airports through the active tracking and
monitoring of passengers and staff using OFDM modulation
technique and Finger print authentication. The details of the
passenger are multiplexed using OFDM .To authenticate the
passenger, the fingerprint along with important identification
information is collected. The details of the passenger can be
transmitted after necessary modulation, and received using various
transceivers placed within the premises of the airport, and checked at
the appropriate check points, thereby increasing the efficiency of
checking. OFDM has been employed for spectral efficiency.
Abstract: Linear stability of wake-shear layers in two-phase
shallow flows is analyzed in the present paper. Stability analysis is
based on two-dimensional shallow water equations. It is assumed that
the fluid contains uniformly distributed solid particles. No dynamic
interaction between the carrier fluid and particles is expected in the
initial moment. Linear stability curves are obtained for different
values of the particle loading parameter, the velocity ratio and the
velocity deficit. It is shown that the increase in the velocity ratio
destabilizes the flow. The particle loading parameter has a stabilizing
effect on the flow. The role of the velocity deficit is also
destabilizing: the increase of the velocity deficit leads to less stable
flow.
Abstract: In today-s competitive environment, the security concerns have grown tremendously. In the modern world, possession is known to be 9/10-ths of the law. Hence, it is imperative for one to be able to safeguard one-s property from worldly harms such as thefts, destruction of property, people with malicious intent etc. Due to the advent of technology in the modern world, the methodologies used by thieves and robbers for stealing have been improving exponentially. Therefore, it is necessary for the surveillance techniques to also improve with the changing world. With the improvement in mass media and various forms of communication, it is now possible to monitor and control the environment to the advantage of the owners of the property. The latest technologies used in the fight against thefts and destruction are the video surveillance and monitoring. By using the technologies, it is possible to monitor and capture every inch and second of the area in interest. However, so far the technologies used are passive in nature, i.e., the monitoring systems only help in detecting the crime but do not actively participate in stopping or curbing the crime while it takes place. Therefore, we have developed a methodology to detect the motion in a video stream environment and this is an idea to ensure that the monitoring systems not only actively participate in stopping the crime, but do so while the crime is taking place. Hence, a system is used to detect any motion in a live streaming video and once motion has been detected in the live stream, the software will activate a warning system and capture the live streaming video.
Abstract: The paper proposes an approach for design of modular
systems based on original technique for modeling and formulation of
combinatorial optimization problems. The proposed approach is
described on the example of personal computer configuration design.
It takes into account the existing compatibility restrictions between
the modules and can be extended and modified to reflect different
functional and users- requirements. The developed design modeling
technique is used to formulate single objective nonlinear mixedinteger
optimization tasks. The practical applicability of the
developed approach is numerically tested on the basis of real modules
data. Solutions of the formulated optimization tasks define the
optimal configuration of the system that satisfies all compatibility
restrictions and user requirements.
Abstract: The objectives of this study are to determine the role of media that influence the values, attitudes and behaviors of Thai youths. Analytical qualitative research techniques were used for this purpose. Data collection based techniques was used which were individual interviews and focus group discussions with journalists, sample of high school and university students, and parents. The results show that “Social Media" is still the most popular media for Thai youths. It is also still in the hands of the marketing business and it can motivate Thai youths to do so many things. The main reasons of media exposure are to find quality information that they want quickly, get satisfaction and can use social media to get more exciting and to build communities. They believe that the need for media and information literacy skills is defined as making judgments, personal integrity, training of family and the behavior of close friends.
Abstract: In this paper we introduce three watermarking methods that can be used to count the number of times that a user has played some content. The proposed methods are tested with audio content in our experimental system using the most common signal processing attacks. The test results show that the watermarking methods used enable the watermark to be extracted under the most common attacks with a low bit error rate.
Abstract: Multi-residue analysis method for penicillins was
developed and validated in bovine muscle, chicken, milk, and flatfish.
Detection was based on liquid chromatography tandem mass
spectrometry (LC/MS/MS). The developed method was validated for
specificity, precision, recovery, and linearity. The analytes were
extracted with 80% acetonitrile and clean-up by a single
reversed-phase solid-phase extraction step. Six penicillins presented
recoveries higher than 76% with the exception of Amoxicillin
(59.7%). Relative standard deviations (RSDs) were not more than
10%. LOQs values ranged from 0.1 and to 4.5 ug/kg. The method was
applied to 128 real samples. Benzylpenicillin was detected in 15
samples and Cloxacillin was detected in 7 samples. Oxacillin was
detected in 2 samples. But the detected levels were under the MRL
levels for penicillins in samples.
Abstract: Beam and diffuse radiation data are extracted analytically from previous measured data on a horizontal surface in Zarqa city. Moreover, radiation data on a tilted surfaces with different slopes have been derived and analyzed. These data are consisting of of beam contribution, diffuse contribution, and ground reflected contribution radiation. Hourly radiation data for horizontal surface possess the highest radiation values on June, and then the values decay as the slope increases and the sharp decreasing happened for vertical surface. The beam radiation on a horizontal surface owns the highest values comparing to diffuse radiation for all days of June. The total daily radiation on the tilted surface decreases with slopes. The beam radiation data also decays with slopes especially for vertical surface. Diffuse radiation slightly decreases with slopes with sharp decreases for vertical surface. The groundreflected radiation grows with slopes especially for vertical surface. It-s clear that in June the highest harvesting of solar energy occurred for horizontal surface, then the harvesting decreases as the slope increases.
Abstract: High voltage generators are being subject to higher
voltage rating and are being designed to operate in harsh conditions.
Stator windings are the main component of generators in which
Electrical, magnetically and thermal stresses remain major failures
for insulation degradation accelerated aging. A large number of
generators failed due to stator winding problems, mainly insulation
deterioration. Insulation degradation assessment plays vital role in the
asset life management. Mostly the stator failure is catastrophic
causing significant damage to the plant. Other than generation loss,
stator failure involves heavy repair or replacement cost. Electro
thermal analysis is the main characteristic for improvement design of
stator slot-s insulation. Dielectric parameters such as insulation
thickness, spacing, material types, geometry of winding and slot are
major design consideration. A very powerful method available to
analyze electro thermal performance is Finite Element Method
(FEM) which is used in this paper. The analysis of various stator coil
and slot configurations are used to design the better dielectric system
to reduce electrical and thermal stresses in order to increase the
power of generator in the same volume of core. This paper describes
the process used to perform classical design and improvement
analysis of stator slot-s insulation.
Abstract: In general, class complexity is measured based on any
one of these factors such as Line of Codes (LOC), Functional points
(FP), Number of Methods (NOM), Number of Attributes (NOA) and so on. There are several new techniques, methods and metrics with
the different factors that are to be developed by the researchers for calculating the complexity of the class in Object Oriented (OO)
software. Earlier, Arockiam et.al has proposed a new complexity measure namely Extended Weighted Class Complexity (EWCC)
which is an extension of Weighted Class Complexity which is proposed by Mishra et.al. EWCC is the sum of cognitive weights of
attributes and methods of the class and that of the classes derived. In EWCC, a cognitive weight of each attribute is considered to be 1.
The main problem in EWCC metric is that, every attribute holds the
same value but in general, cognitive load in understanding the
different types of attributes cannot be the same. So here, we are proposing a new metric namely Attribute Weighted Class Complexity
(AWCC). In AWCC, the cognitive weights have to be assigned for the attributes which are derived from the effort needed to understand
their data types. The proposed metric has been proved to be a better
measure of complexity of class with attributes through the case studies and experiments
Abstract: The recurring decimal of rural and urban poverty in
Nigeria, resulting from lack of sustainable livelihood activities by
the people due to non-diversification of the economy, necessitated
this study. One hundred snail farmers were randomly selected in
Akure North and Akure South Local Government areas of Ondo
State, Southwest Nigeria where snail farming is widely practised.
Data collection was through questionnaires administration and onsite
observation of farms. Data obtained were subjected to
descriptive statistics, Student-s t-test and regression analysis. Cost
benefit ratio (CBR) and rate of return on investment (RORI) were
calculated in order to determine the poverty alleviation potentials of
snail farming in the study areas. Although snail farming was
profitable and viable, it was below poverty line. With time and more
knowledge in its farming activities, and with more people taking to
snail production, its poverty alleviation and reduction potentials will
increase.
Abstract: Polymers are one of the most widely used materials in our every day life. The subject of renewable resources has attracted great attention in the last period of time. New polymeric materials derived from renewable resources, like carbohydrates draw attention to public eye especially because of their biocompatibility and biodegradability. The aim of our paper was to obtain environmentally compatible polymers from monosaccharides. Novel glycopolymers based on D-glucose have been obtained from copolymerization of a new monomer carrying carbohydrate moiety with methyl methacrylate (MMA) via free radical bulk polymerization. Differential scanning calorimetry (DSC) was performed in order to study the copolymerization process of the monomer into the chosen co-monomer; the activation energy of this process was evaluated using Ozawa method. The copolymers obtained were characterized using ATR-FTIR spectroscopy. The thermal stability of the obtained products was studied by thermogravimetry (TG).
Abstract: The research study is carried out to determine the efficiency of the Biofilm sewage treatment plant which is located at the Engineering Complex-s. Wastewater analyses have been carried out at the Environmental Engineering laboratory to study the six parameters: Biochemical Oxygen Demand BOD, Chemical Oxygen Demand COD l, and Total Suspended Solids TSS, Ammoniac Nitrogen NH3-N and Phosphorous P which have been selected to determine the wastewater quality. The plant was designed to treat 750 Pe (population equivalent) at hydraulic retention time of 5 hours in the aerobic zone. The results show that Biofilm wastewater treatment plant was able to treat sewage successfully at different flow condition. The discharge has fulfilled the Malaysia Environmental of Standard A water quality. The achieved BOD removal is more than 85%, COD is more than 80%, TSS is more than 80%, NH3-N is more than 70%, and P was more than 70%. The Biofilm system provides a very efficient process for sewage treatment and it is compact in structure thus minimizes the required land area.
Abstract: The volume of biosolids produced in Malaysia
nowadays had increased proportionally to its population size. The end
products from the waste treatments were mounting, thus inevitable
that in the end the environment will be surrounded by the waste. This
study was conducted to investigate the suitability of biosolids to be
reused as fertilizer for non-food crop. By varying the concentration of
biosolids applied onto the soil, growth of five ornamental plant
samples were tested for eight consecutive weeks. The results show
that the pH of the soil after the addition of biosolids ranges from 6.45
to 6.56 which is suitable for the plant growth. The soil samples that
contains biosolid also show higher amount of macronutrients (N, P,
K) and the heavy metals content are significantly increased in the
plant however it does not exceed the guidelines drawn by the
Environmental Protection Agency. It is also proven that there was
only small significant different in the performance of plant growth
between biosolids and commercial fertilizer. It can be seen that
biosolids was able to perform just as well as commercial fertilizer.
Abstract: Commercial nanocomposite food packaging type nano-silver containers were characterised using scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDX). The presence of nanoparticles consistent with the incorporation of 1% nano-silver (Ag) and 0.1% titanium dioxide (TiO2) nanoparticle into polymeric materials formed into food containers was confirmed. Both nanomaterials used in this type of packaging appear to be embedded in a layered configuration within the bulk polymer. The dimensions of the incorporated nanoparticles were investigated using X-ray diffraction (XRD) and determined by calculation using the Scherrer Formula; these were consistent with Ag and TiO2 nanoparticles in the size range 20-70nm both were spherical shape nanoparticles. Antimicrobial assessment of the nanocomposite container has also been performed and the results confirm the antimicrobial activity of Ag and TiO2 nanoparticles in food packaging containers. Migration assessments were performed in a wide range of food matrices to determine the migration of nanoparticles from the packages. The analysis was based upon the relevant European safety Directives and involved the application of inductively coupled plasma mass spectrometry (ICP-MS) to identify the range of migration risk. The data pertain to insignificance levels of migration of Ag and TiO2 nanoparticles into the selected food matrices.
Abstract: Interactive public displays give access as an
innovative media to promote enhanced communication between
people and information. However, digital public displays are subject
to a few constraints, such as content presentation. Content
presentation needs to be developed to be more interesting to attract
people’s attention and motivate people to interact with the display. In
this paper, we proposed idea to implement contents with interaction
elements for vision-based digital public display. Vision-based
techniques are applied as a sensor to detect passers-by and theme
contents are suggested to attract their attention for encouraging them
to interact with the announcement content. Virtual object, gesture
detection and projection installation are applied for attracting
attention from passers-by. Preliminary study showed positive
feedback of interactive content designing towards the public display.
This new trend would be a valuable innovation as delivery of
announcement content and information communication through this
media is proven to be more engaging.