Abstract: This paper presents the electromagnetic interference
(EMI) shielding effectiveness of rice husk and carbon nanotubes
(RHCNTs) composites in the X-band region (8.2-12.4 GHz). The
difference weight ratio of carbon nanotubes (CNTs) were mix with
the rice husk. The rectangular waveguide technique was used to
measure the complex permittivity of the RHCNTs composites
materials. The complex permittivity is represented in terms of both
the real and imaginary parts of permittivity in X-band frequency. The
conductivity of RHCNTs shows increasing when the ratio of CNTs
mixture increases. The composites materials were simulated using
Computer Simulation Technology (CST) Microwave Studio
simulation software. The shielding effectiveness of RHCNTs and
pure rice husk was compared. The highest EMI SE of 30 dB is
obtained for RHCNTs composites of 10 wt % CNTs with 10mm
thickness.
Abstract: This work presents a Computational Fluid Dynamics
(CFD) simulation of a butterfly valve used to control the flow of
combustible gas mixture in an industrial process setting.The work
uses CFD simulation to analyze the flow characteristics in the
vicinity of the valve, including the pressure distributions and
Frequency spectrum of the pressure pulsations downstream the valves
and the vortex shedding allow predicting the torque fluctuations
acting on the valve shaft and the possibility of generating mechanical
vibration and resonance.These fluctuations are due to aerodynamic
torque resulting from fluid turbulence and vortex shedding in the
valve vicinity.
The valve analyzed is located in a pipeline between two opposing
90o elbows, which exposes the valve and the surrounding structure to
the turbulence generated upstream and downstream the elbows at
either end of the pipe.CFD simulations show that the best location for
the valve from a vibration point of view is in the middle of the pipe
joining the elbows.
Abstract: In new energy development, wind power has boomed.
It is due to the proliferation of wind parks and their operation in
supplying the national electric grid with low cost and clean resources.
Hence, there is an increased need to establish a proactive
maintenance for wind turbine machines based on remote control and
monitoring. That is necessary with a real-time wireless connection in
offshore or inaccessible locations while the wired method has many
flaws. The objective of this strategy is to prolong wind turbine
lifetime and to increase productivity. The hardware of a remote
control and monitoring system for wind turbine parks is designed. It
takes advantage of GPRS or Wi-Max wireless module to collect data
measurements from different wind machine sensors through IP based
multi-hop communication. Computer simulations with Proteus ISIS
and OPNET software tools have been conducted to evaluate the
performance of the studied system. Study findings show that the
designed device is suitable for application in a wind park.
Abstract: This paper presents reliability indices evaluation of the
rotor core magnetization of the induction motor operated as a self
excited induction generator by using probability distribution approach
and Monte Carlo simulation. Parallel capacitors with calculated
minimum capacitive value across the terminals of the induction motor
operated as a SEIG with unregulated shaft speed have been connected
during the experimental study. A three phase, 4 poles, 50Hz, 5.5 hp,
12.3A, 230V induction motor coupled with DC Shunt Motor was
tested in the electrical machine laboratory with variable reactive loads.
Based on this experimental study, it is possible to choose a reliable
induction machines operated as a SEIG for unregulated renewable
energy application in remote area or where grid is not available.
Failure density function, cumulative failure distribution function,
survivor function, hazard model, probability of success and
probability of failure for reliability evaluation of the three phase
induction motor operating as a SEIG have been presented graphically
in this paper.
Abstract: Renewable energy is derived from natural processes
that are replenished constantly. Included in the definition is
electricity and heat generated from solar, wind, ocean, hydropower,
biomass, geothermal resources, and bio-fuels and hydrogen derived
from renewable resources. Each of these sources has unique
characteristics which influence how and where they are used. This
paper presents the modeling the simulation of solar and hydro hybrid
energy sources in MATLAB/SIMULINK environment. It simulates
all quantities of Hybrid Electrical Power system (HEPS) such as AC
output current of the inverter that injected to the load/grid, load
current, grid current. It also simulates power output from PV and
Hydraulic Turbine Generator (HTG), power delivered to or from grid
and finally power factor of the inverter for PV, HTG and grid. The
proposed circuit uses instantaneous p-q (real-imaginary) power
theory.
Abstract: In this paper a scheme is proposed for generating
a programmable current reference which can be implemented
in the CMOS technology. The current can be varied over a
wide range by changing an external voltage applied to one
of the control gates of FGMOS (Floating Gate MOSFET).
For a range of supply voltages and temperature, CMOS
current reference is found to be dependent, this dependence
is compensated by subtracting two current outputs with the
same dependencies on the supply voltage and temperature.
The system performance is found to improve with the
use of FGMOS. Mathematical analysis of the proposed
circuit is done to establish supply voltage and temperature
independence. Simulation and performance evaluation of the
proposed current reference circuit is done using TANNER
EDA Tools. The current reference shows the supply and
temperature dependencies of 520 ppm/V and 312 ppm/oC,
respectively. The proposed current reference can operate down
to 0.9 V supply.
Abstract: A finite difference/front tracking method is used to
study the motion of three-dimensional deformable drops suspended in
plane Poiseuille flow at non-zero Reynolds numbers. A parallel
version of the code was used to study the behavior of suspension on a
reasonable grid resolution (grids). The viscosity and density of drops
are assumed to be equal to that of the suspending medium. The effect
of the Reynolds number is studied in detail. It is found that drops
with small deformation behave like rigid particles and migrate to an
equilibrium position about half way between the wall and the
centerline (the Segre-Silberberg effect). However, for highly
deformable drops there is a tendency for drops to migrate to the
middle of the channel, and the maximum concentration occurs at the
centerline. The effective viscosity of suspension and the fluctuation
energy of the flow across the channel increases with the Reynolds
number of the flow.
Abstract: In this paper family of multilevel inverter topology
with reduced number of power switches is presented. The proposed
inverter can generate both even and odd level. The proposed topology
is suitable for symmetric structure. The proposed symmetric inverter
results in reduction of power switches, power diode and gate driver
circuits and also it may further minimize the installation area and
cost. To prove the superiority of proposed topology is compared with
conventional topologies. The performance of this symmetric
multilevel inverter has been tested by computer based simulation and
prototype based experimental setup for nine-level inverter is
developed and results are verified.
Abstract: The aim of this paper is to propose a novel technique
to guarantee Quality of Service (QoS) in a highly dynamic
environment. The MANET changes its topology dynamically as the
nodes are moved frequently. This will cause link failure between
mobile nodes. MANET cannot ensure reliability without delay. The
relay node is selected based on achieving QoS in previous
transmission. It considers one more factor Connection Existence
Period (CEP) to ensure reliability. CEP is to find out the period
during that connection exists between the nodes. The node with
highest CEP becomes a next relay node. The relay node is selected
dynamically to avoid frequent failure. The bandwidth of each link
changed dynamically based on service rate and request rate. This
paper proposes Active bandwidth setting up algorithm to guarantee
the QoS. The series of results obtained by using the Network
Simulator (NS-2) demonstrate the viability of our proposed
techniques.
Abstract: The phased-array ultrasound transducer types are
utilities for medical ultrasonography as well as optical imaging.
However, their discontinuity characteristic limits the applications due
to the artifacts contaminated into the reconstructed images. Because
of the effects of the ultrasound pressure field pattern to the echo
ultrasonic waves as well as the optical modulated signal, the side
lobes of the focused ultrasound beam induced by discontinuity of the
phased-array ultrasound transducer might the reason of the artifacts.
In this paper, a simple method in approach of numerical simulation
was used to investigate the limitation of discontinuity of the elements
in phased-array ultrasound transducer and their effects to the
ultrasound pressure field. Take into account the change of ultrasound
pressure field patterns in the conditions of variation of the pitches
between elements of the phased-array ultrasound transducer, the
appropriated parameters for phased-array ultrasound transducer
design were asserted quantitatively.
Abstract: Human movement in the real world provides
important information for developing human behaviour models and
simulations. However, it is difficult to assess ‘real’ human behaviour
since there is no established method available. As part of the AUNTSUE
(Accessibility and User Needs in Transport – Sustainable Urban
Environments) project, this research aimed to propose a method to
assess human movement and behaviour in crowded areas. The
method is based on the three major steps of video recording,
conceptual behavior modelling and video analysis. The focus is on
individual human movement and behaviour in normal situations
(panic situations are not considered) and the interactions between
individuals in localized areas. Emphasis is placed on gaining
knowledge of characteristics of human movement and behaviour in
the real world that can be modelled in the virtual environment.
Abstract: A novel simulation method to determine the
displacements of machine tools due to thermal factors is presented.
The specific characteristic of this method is the employment of
original CAD data from the design process chain, which is
interpreted by an algorithm in terms of geometry-based allocation of
convection and radiation parameters. Furthermore analogous models
relating to the thermal behaviour of machine elements are
automatically implemented, which were gained by extensive
experimental testing with thermography imaging. With this a
transient simulation of the thermal field and in series of the
displacement of the machine tool is possible simultaneously during
the design phase. This method was implemented and is already used
industrially in the design of machining centres in order to improve
the quality of herewith manufactured workpieces.
Abstract: This paper presents a method for the efficient
implementation of a unidirectional or bidirectional DC/DC converter.
The DC/DC converter is used essentially for energy exchange
between the low voltage service battery and a high voltage battery
commonly found in Electric Vehicle applications. In these
applications, apart from cost, efficiency of design is an important
characteristic. A useful way to reduce the size of electronic
equipment in the electric vehicles is proposed in this paper. The
technique simplifies the mechanical complexity and maximizes the
energy usage using the latest converter control techniques. Moreover
a bidirectional battery charger for hybrid electric vehicles is also
implemented in this paper. Several simulations on the test system
have been carried out in Matlab/Simulink environment. The results
exemplify the robustness of the proposed design methodology in case
of a 1.5 KW DC-DC converter.
Abstract: Nonstandard tests are necessary for analyses and
verification of new developed structural and technological solutions
with application of composite materials. One of the most critical
primary structural parts of a typical aerospace structure is T-joint.
This structural element is loaded mainly in shear, bending, peel and
tension. The paper is focused on the shear loading simulations. The
aim of the work is to obtain a representative uniform distribution of
shear loads along T-joint during the mechanical testing. A new
design of T-joint test procedure, numerical simulation and
optimization of representative boundary conditions are presented.
The different conditions and inaccuracies both in simulations and
experiments are discussed. The influence of different parameters on
stress and strain distributions is demonstrated on T-joint made of
CFRP (carbon fibre reinforced plastic). A special test rig designed by
VZLU (Aerospace Research and Test Establishment) for T-shear test
procedure is presented.
Abstract: This paper presents a 4-DOF nonlinear model of a
cracked de Laval rotor-stator system derived based on Energy
Principles. The model has been used to simulate coupled torsionallateral
response of the faulty system with multiple parametric
excitations; rotor-stator-rub, a breathing transverse crack, eccentric
mass and an axial force. Nonlinearity of a “breathing” crack is
incorporated in the model using a simple hinge mechanism suitable
for a shallow crack. Response of the system while passing via its
critical speed with intermittent rotor-stator rub is analyzed. Effects of
eccentricity with phase and acceleration are investigated. Features of
crack, rub and eccentricity in vibration response are explored for
condition monitoring. The presence of a crack and rub are observable
in the power spectrum despite excitations by an axial force and rotor
unbalance. Obtained results are consistent with existing literature and
could be adopted into rotor condition monitoring strategies.
Abstract: reliability-based methodology for the assessment
and evaluation of reinforced concrete (R/C) structural elements of
concrete structures is presented herein. The results of the reliability
analysis and assessment for R/C structural elements were verified by
the results obtained through deterministic methods. The outcomes of
the reliability-based analysis were compared against currently
adopted safety limits that are incorporated in the reliability indices
β’s, according to international standards and codes. The methodology
is based on probabilistic analysis using reliability concepts and
statistics of the main random variables that are relevant to the subject
matter, and for which they are to be used in the performance-function
equation(s) associated with the structural elements under study.
These methodology techniques can result in reliability index β, which
is commonly known as the reliability index or reliability measure
value that can be utilized to assess and evaluate the safety, human
risk, and functionality of the structural component. Also, these
methods can result in revised partial safety factor values for certain
target reliability indices that can be used for the purpose of
redesigning the R/C elements of the building and in which they could
assist in considering some other remedial actions to improve the
safety and functionality of the member.
Abstract: In this paper, design of solid-state battery/supercapacitor emulator based on dc-dc boost converter is described.
The emulator mimics charging behavior of any storage device based
on a predefined behavior set by the user. The device is operated by a
two-level control structure: high-level emulating controller and low-
level input voltage controller. Simulation and experimental results are
shown to demonstrate the emulator operation.
Abstract: This paper is devoted to the study of a viscous
incompressible flow around a circular cylinder performing harmonic
oscillations, especially the steady streaming phenomenon. The
research methodology is based on the asymptotic explanation method
combined with the computational bifurcation analysis. The research
approach develops Schlichting and Wang decomposition method.
Present studies allow to identify several regimes of the secondary
streaming with different flow structures. The results of the research
are in good agreement with experimental and numerical simulation
data.
Abstract: In this paper, we present a comparative assessment of
Space Vector Pulse Width Modulation (SVPWM) and Model
Predictive Control (MPC) for two-level three phase (2L-3P) Voltage
Source Inverter (VSI). VSI with associated system is subjected to
both control techniques and the results are compared.
Matlab/Simulink was used to model, simulate and validate the
control schemes. Findings of this study show that MPC is superior to
SVPWM in terms of total harmonic distortion (THD) and
implementation.
Abstract: A wireless sensor network (WSN) is a collection of
sensor nodes organized into a cooperative network. These nodes
communicate through a wireless antenna. Reduction in physical size
and multiband operation is an important requirement of WSN
antenna. Fractal antenna is used for miniaturization and multiband
operation. The self-similar or self-affine and space filling property of
fractal geometry increases the effective electrical length of the
antenna, reduces the size and make them frequency independent. This
paper elaborates on Dual band fractal antenna with Coplanar
Waveguide (CPW) feed for WSN. The proposed antenna is designed
on a FR4 substrate with the dimension of 27mm x 28.5mm x 1.6mm,
resonates at 2.4GHz and 5.2GHz with a return loss less than -10dB.
The design and simulation process is carried out using IE3D
simulation software. The simulated and measured results are found in
good agreement.