Abstract: Structural failure is caused mainly by damage that
often occurs on structures. Many researchers focus on to obtain very
efficient tools to detect the damage in structures in the early state. In
the past decades, a subject that has received considerable attention in
literature is the damage detection as determined by variations in the
dynamic characteristics or response of structures. The study presents
a new damage identification technique. The technique detects the
damage location for the incomplete structure system using output
data only. The method indicates the damage based on the free
vibration test data by using ‘Two Points Condensation (TPC)
technique’. This method creates a set of matrices by reducing the
structural system to two degrees of freedom systems. The current
stiffness matrices obtain from optimization the equation of motion
using the measured test data. The current stiffness matrices compare
with original (undamaged) stiffness matrices. The large percentage
changes in matrices’ coefficients lead to the location of the damage. TPC technique is applied to the experimental data of a simply
supported steel beam model structure after inducing thickness change
in one element, where two cases consider. The method detects the
damage and determines its location accurately in both cases. In
addition, the results illustrate these changes in stiffness matrix can be
a useful tool for continuous monitoring of structural safety using
ambient vibration data. Furthermore, its efficiency proves that this
technique can be used also for big structures.
Abstract: Academic libraries in Malaysia are still not prepared
for disaster even though several occasions have been reported. The
study sets out to assess the current status of preparedness in disaster
management among Malaysian academic libraries in the State of
Selangor and the Federal Territory of Kuala Lumpur. To obtain a
base level of knowledge on disaster preparedness of current practices,
a questionnaire was distributed to chief librarians or their assignees in
charge of disaster or emergency preparedness at 40 academic
libraries and 34 responses were received. The study revolved around
the current status of preparedness, on various issues including
existence of disaster preparedness plan among academic libraries in
Malaysia, disaster experiences by the academic libraries, funding,
risk assessment activities and involvement of library staff in disaster
management. Frequency and percentage tables were used in the
analysis of the data collected. Some of the academic libraries under
study have experienced one form of disaster or the other. Most of the
academic libraries do not have a written disaster preparedness plan.
The risk assessments and staff involvement in disaster preparedness
by these libraries were generally adequate.
Abstract: Comparative analysis of the properties of melon seed,
coconut fruit and their oil yield were evaluated in this work using
standard analytical technique AOAC. The results of the analysis
carried out revealed that the moisture contents of the samples studied
are 11.15% (melon) and 7.59% (coconut). The crude lipid content are
46.10% (melon) and 55.15% (coconut).The treatment combinations
used (leaching time, leaching temperature and solute: solvent ratio)
showed significant difference (p < 0.05) in yield between the
samples, with melon oil seed flour having a higher percentage range
of oil yield (41.30 – 52.90%) and coconut (36.25 – 49.83%). The
physical characterization of the extracted oil was also carried out.
The values gotten for refractive index are 1.487 (melon seed oil) and
1.361 (coconut oil) and viscosities are 0.008 (melon seed oil) and
0.002 (coconut oil). The chemical analysis of the extracted oils shows
acid value of 1.00mg NaOH/g oil (melon oil), 10.050mg NaOH/g oil
(coconut oil) and saponification value of 187.00mg/KOH (melon oil)
and 183.26mg/KOH (coconut oil). The iodine value of the melon oil
gave 75.00mg I2/g and 81.00mg I2/g for coconut oil. A standard
statistical package Minitab version 16.0 was used in the regression
analysis and analysis of variance (ANOVA). The statistical software
mentioned above was also used to optimize the leaching process.
Both samples gave high oil yield at the same optimal conditions. The
optimal conditions to obtain highest oil yield ≥ 52% (melon seed)
and ≥ 48% (coconut seed) are solute - solvent ratio of 40g/ml,
leaching time of 2hours and leaching temperature of 50oC. The two
samples studied have potential of yielding oil with melon seed giving
the higher yield.
Abstract: Social Avoidance is one of the most important
problems that face a good number of disabled students. It results from
the negative attitudes of non-disabled students, teachers and others.
Some of the past research has shown that non-disabled individuals
hold negative attitudes toward persons with disabilities. The present
study aims to alleviate Social Avoidance by applying the Cognitive
Behavioral Intervention. 24 Blind students aged 19–24 (university students) were randomly
chosen we compared an experimental group (consisted of 12
students) who went through the intervention program, with a control
group (12 students also) who did not go through such intervention.
We used the Social Avoidance and Distress Scale (SADS) to assess
social anxiety and distress behavior. The author used many
techniques of cognitive behavioral intervention such as modeling,
cognitive restructuring, extension, contingency contracts, selfmonitoring,
assertiveness training, role play, encouragement and
others. Statistically, T-test was employed to test the research
hypothesis. Result showed that there is a significance difference between the
experimental group and the control group after the intervention and
also at the follow up stages of the Social Avoidance and Distress
Scale. Also for the experimental group, there is a significance
difference before the intervention and the follow up stages for the
scale. Results showed that, there is a decrease in social avoidance.
Accordingly, cognitive behavioral intervention program was
successful in decreasing social avoidance for blind students.
Abstract: The ventilated façade has great advantages when
compared to traditional façades as it reduces the air conditioning
thermal loads due to the stack effect induced by solar radiation in the
air chamber. Optimizing energy consumption by using a ventilated
façade can be used not only in newly built buildings but also it can be
implemented in existing buildings, opening the field of
implementation to energy building retrofitting works. In this sense, the following three prototypes of façade where
designed, built and further analyzed in this research: non-ventilated
façade (NVF); slightly ventilated façade (SLVF) and strongly
ventilated façade (STVF). The construction characteristics of the
three facades are based on the Spanish regulation of building
construction “Technical Building Code”. The façades have been
monitored by type-k thermocouples in a representative day of the
summer season in Madrid (Spain). Moreover, an analysis of variance
(ANOVA) with repeated measures, studying the thermal lag in the
ventilated and no-ventilated façades has been designed. Results show that STVF façade presents higher levels of thermal
inertia as the thermal lag reduces up to 17% (daily mean) compared
to the non-ventilated façade. In addition, the statistical analysis
proves that an increase of the ventilation holes size in STVF façades
can improve the thermal lag significantly (p >0.05) when compared
to the SLVF façade.
Abstract: Temperature effect on the performance of a photovoltaic module is one of the main concerns that face this renewable energy, especially in hot arid region, e.g. United Arab Emirates. Overheating of the PV modules reduces the open circuit voltage and the efficiency of the modules dramatically. In this work, water-cooling is developed to enhance the performance of PV modules. Different scenarios are tested under UAE weather conditions: front, back and double cooling. A spraying system is used for the front cooling whether a direct contact water system is used for the back cooling. The experimental results are compared to non-cooling module and the performance of the PV module is determined for different situations. The experimental results show that the front cooling is more effective than the back cooling and may decrease the temperature of the PV module significantly.
Abstract: This paper presents a grid synchronization technique based on adaptive notch filter for SPV (Solar Photovoltaic) system along with MPPT (Maximum Power Point Tracking) techniques. An efficient grid synchronization technique offers proficient detection of various components of grid signal like phase and frequency. It also acts as a barrier for harmonics and other disturbances in grid signal. A reference phase signal synchronized with the grid voltage is provided by the grid synchronization technique to standardize the system with grid codes and power quality standards. Hence, grid synchronization unit plays important role for grid connected SPV systems. As the output of the PV array is fluctuating in nature with the meteorological parameters like irradiance, temperature, wind etc. In order to maintain a constant DC voltage at VSC (Voltage Source Converter) input, MPPT control is required to track the maximum power point from PV array. In this work, a variable step size P & O (Perturb and Observe) MPPT technique with DC/DC boost converter has been used at first stage of the system. This algorithm divides the dPpv/dVpv curve of PV panel into three separate zones i.e. zone 0, zone 1 and zone 2. A fine value of tracking step size is used in zone 0 while zone 1 and zone 2 requires a large value of step size in order to obtain a high tracking speed. Further, adaptive notch filter based control technique is proposed for VSC in PV generation system. Adaptive notch filter (ANF) approach is used to synchronize the interfaced PV system with grid to maintain the amplitude, phase and frequency parameters as well as power quality improvement. This technique offers the compensation of harmonics current and reactive power with both linear and nonlinear loads. To maintain constant DC link voltage a PI controller is also implemented and presented in this paper. The complete system has been designed, developed and simulated using SimPower System and Simulink toolbox of MATLAB. The performance analysis of three phase grid connected solar photovoltaic system has been carried out on the basis of various parameters like PV output power, PV voltage, PV current, DC link voltage, PCC (Point of Common Coupling) voltage, grid voltage, grid current, voltage source converter current, power supplied by the voltage source converter etc. The results obtained from the proposed system are found satisfactory.
Abstract: The world crude oil demand is projected to rise to 108.5 million bbl/d by the year 2035. With reserves estimated at 869 billion tonnes worldwide, coal remains an abundant resource. The aim of this work was to produce a high value hydrocarbon liquid product using a Direct Coal Liquefaction (DCL) process at, relatively mild operating conditions. Via hydrogenation, the temperature-staged approach was investigated in a dual reactor lab-scale pilot plant facility. The objectives included maximising thermal dissolution of the coal in the presence of tetralin as the hydrogen donor solvent in the first stage with 2:1 and 3:1 solvent: coal ratios. Subsequently, in the second stage, hydrogen saturation, in particular, hydrodesulphurization (HDS) performance was assessed. Two commercial hydrotreating catalysts were investigated viz. NickelMolybdenum (Ni-Mo) and Cobalt-Molybdenum (Co-Mo). GC-MS results identified 77 compounds and various functional groups present in the first and second stage liquid product. In the first stage 3:1 ratios and liquid product yields catalysed by magnetite were favoured. The second stage product distribution showed an increase in the BTX (Benzene, Toluene, Xylene) quality of the liquid product, branched chain alkanes and a reduction in the sulphur concentration. As an HDS performer and selectivity to the production of long and branched chain alkanes, Ni-Mo had an improved performance over Co-Mo. Co-Mo is selective to a higher concentration of cyclohexane. For 16 days on stream each, Ni-Mo had a higher activity than Co-Mo. The potential to cover the demand for low–sulphur, crude diesel and solvents from the production of high value hydrocarbon liquid in the said process, is thus demonstrated.
Abstract: The seriously damaged structures during earthquakes
show the need and importance of design of reinforced concrete
structures with high ductility. Reinforced concrete beam-column
joints have an important function in all structures. Under seismic
excitation, the beam column joint region is subjected to horizontal
and vertical shear forces whose magnitude is many times higher than
the adjacent beam and column. Strength and ductility of structures
depends mainly on proper detailing of the reinforcement in beamcolumn
joints and the old structures were found ductility deficient.
DSP materials are obtained by using high quantities of super
plasticizers and high volumes of micro silica. In the case of High
Performance Densified Small Particle Concrete (HPDSPC), since
concrete is dense even at the micro-structure level, tensile strain
would be much higher than that of the conventional SFRC, SIFCON
& SIMCON. This in turn will improve cracking behaviour, ductility
and energy absorption capacity of composites in addition to
durability. The fine fibers used in our mix are 0.3mm diameter and 10
mm which can be easily placed with high percentage. These fibers
easily transfer stresses and act as a composite concrete unit to take up
extremely high loads with high compressive strength. HPDSPC
placed in the beam column joints helps in safety of human life due to
prolonged failure.
Abstract: The study focused on the analysis of the Adjusted
Rorschach Comprehensive System’s responses. The objective of this
study is to analyse the participants’ response rate of the Adjusted
Rorschach Comprehensive System with regards to critical
psychology approach. The use of critical psychology theory in this
study was crucial because it responds to the current inadequate
western theory or practice in the field of psychology. The study
adopted a qualitative approach and a case study design. The study
was grounded on interpretivist paradigm. The sample size comprised
six learners (three boys and three girls, aged of 14 years) from
historically disadvantaged school in the Western Cape, South Africa.
The Adjusted Rorschach Comprehensive System (ARCS)
administration procedure, biographical information, semi-structured
interviews, and observation were used to collect data. Data was
analysed using thematic framework. The study found out that, factors
that increased the response rates during the administration of ARCS
were, language, seating arrangement, drawing, viewing, and
describing. The study recommended that, psychological test
designers take into consideration the philosophy or worldviews of the
local people for whom the test is designed to minimize low response
rates.
Abstract: Milk is considered as an essential and complete food.
The present study was conducted at Milk Plant Mohali especially in
reference to the procurement section where the cash inflow was
maximum, with the objective to achieve higher productivity and
reduce wastage of milk. In milk plant it was observed that during the
month of Jan-2014 to March-2014 the average procurement of milk
was Rs. 4, 19, 361 liter per month and cost of procurement of milk is
Rs 35/- per liter. The total cost of procurement thereby equal to Rs.
1crore 46 lakh per month, but there was mismatch in procurementproduction
of milk, which leads to an average loss of Rs. 12, 94, 405
per month. To solve the procurement-production problem Quality
Control Tools like brainstorming, Flow Chart, Cause effect diagram
and Pareto analysis are applied wherever applicable. With the
successful implementation of Quality Control tools an average saving
of Rs. 4, 59, 445 per month is done.
Abstract: The effect of carbon nanofibers (CNFs) on the
electrical properties of Poly(vinylidene fluoride-hexafluoropropylene)
(P(VdF-HFP)) based gel polymer electrolytes has been investigated
in the present work. The length and diameter ranges of CNFs used in
the present work are 5-50 μm and 200-600 nm respectively. The
nanocomposite gel polymer electrolytes have been synthesized by
solution casting technique with varying CNFs content in terms of
weight percentage. Electrochemical impedance analysis demonstrates
that the reinforcement of carbon nanofibers significantly enhances the
ionic conductivity of the polymer electrolyte. The decrease of
crystallinity of P(VdF-HFP) due the addition of CNFs has been
confirmed by X-ray diffraction (XRD). The interaction of CNFs with
various constituents of nanocomposite gel polymer electrolytes has
been assessed by Fourier Transform Infrared (FTIR) spectroscopy.
Moreover CNFs added gel polymer electrolytes offer superior
thermal stability as compared to that of CNFs free electrolytes as
confirmed by Thermogravimetric analysis (TGA).
Abstract: Drought is one of the most serious problems posing a
grave threat to cereals production including maize. Maize
improvement in drought-stress tolerance poses a great challenge as
the global need for food and bio-energy increases. Thus, the current
study was planned to explore the variations and determine the
performance of target traits of maize hybrids at grain growth stage
under drought conditions during 2014 under Adana, Mediterranean
climate conditions, Turkey. Maize hybrids (Sancia, Indaco,
71May69, Aaccel, Calgary, 70May82, 72May80) were evaluated
under (irrigated and water stress). Results revealed that, grain yield
and yield traits had a negative effects because of water stress
conditions compared with the normal irrigation. As well as, based on
the result under normal irrigation, the maximum biological yield and
harvest index were recorded. According to the differences among
hybrids were found that, significant differences were observed among
hybrids with respect to yield and yield traits under current research. Based on the results, grain weight had more effect on grain yield
than grain number during grain filling growth stage under water
stress conditions. In this concern, according to low drought
susceptibility index (less grain yield losses), the hybrid (Indaco) was
more stable in grain number and grain weight. Consequently, it may
be concluded that this hybrid would be recommended for use in the
future breeding programs for production of drought tolerant hybrids.
Abstract: E-retailing is the sale of goods online that takes place
over the Internet. The Internet has shrunk the entire World. World eretailing
is growing at an exponential rate in the Americas, Europe
and Asia. However, e-retailing costs require expensive investment,
such as hardware, software, and security systems. Cloud computing
technology is internet-based computing for the management and
delivery of applications and services. Cloud-based e-retailing
application models allow enterprises to lower their costs with their
effective implementation of e-retailing activities. In this paper, we
describe the concept of cloud computing and present the architecture
of cloud computing, combining the features of e-retailing. In
addition, we propose a strategy for implementing cloud computing
with e-retailing. Finally, we explain the benefits from the
architecture.
Abstract: This paper discusses the general methods to saturation
in the steady-state, two axis (d & q) frame models of synchronous
machines. In particular, the important role of the magnetic coupling
between the d-q axes (cross-magnetizing phenomenon), is
demonstrated. For that purpose, distinct methods of saturation
modeling of dumper synchronous machine with cross-saturation are
identified, and detailed models synthesis in d-q axes. A number of
models are given in the final developed form. The procedure and the
novel models are verified by a critical application to prove the
validity of the method and the equivalence between all developed
models is reported. Advantages of some of the models over the
existing ones and their applicability are discussed.
Abstract: This paper addresses minimizing the makespan of the
distributed permutation flow shop scheduling problem. In this
problem, there are several parallel identical factories or flowshops
each with series of similar machines. Each job should be allocated to
one of the factories and all of the operations of the jobs should be
performed in the allocated factory. This problem has recently gained
attention and due to NP-Hard nature of the problem, metaheuristic
algorithms have been proposed to tackle it. Majority of the proposed
algorithms require large computational time which is the main
drawback. In this study, a general variable neighborhood search
algorithm (GVNS) is proposed where several time-saving schemes
have been incorporated into it. Also, the GVNS uses the sophisticated
method to change the shaking procedure or perturbation depending
on the progress of the incumbent solution to prevent stagnation of the
search. The performance of the proposed algorithm is compared to
the state-of-the-art algorithms based on standard benchmark
instances.
Abstract: Hollow section for bridge columns has some
advantages. However, current seismic design codes do not provide
design regulations for hollow bridge piers. There have been many
experimental studied for hollow reinforced concrete piers in the world.
But, Study for hollow section for bridge piers in Korea has been begun
with approximately 2000s. There has been conducted experimental
study for hollow piers of flexural controlled sections by Yeungnam
University, Sung kyunkwan University, Korea Expressway
Corporation in 2009. This study concluded that flexural controlled
sections for hollow piers showed the similar behavior to solid sections.
And there have been conducted experimental study for hollow piers of
compression controlled sections by Yeungnam University, Korea
Institute of Construction Technology in 2012. This study concluded
that compression controlled sections for hollow piers showed
compression fracture of concrete in inside wall face. Samsung
Construction & Trading Corporation has been conducted study with
Yeungnam University for reduce the quantity of reinforcement details
about hollow piers. Reduce the quantity of reinforcement details are
triangular cross tie. This study concluded that triangular reinforcement
details showed the similar behavior as compared with existing
reinforcement details.
Abstract: This paper will discuss how we optimize our physical
verification flow in our IC Design Department having various rule
decks from multiple foundries. Our ultimate goal is to achieve faster
time to tape-out and avoid schedule delay. Currently the physical
verification runtimes and memory usage have drastically increased
with the increasing number of design rules, design complexity, and
the size of the chips to be verified. To manage design violations, we
use a number of solutions to reduce the amount of violations needed
to be checked by physical verification engineers. The most important
functions in physical verifications are DRC (design rule check), LVS
(layout vs. schematic), and XRC (extraction). Since we have a
multiple number of foundries for our design tape-outs, we need a
flow that improve the overall turnaround time and ease of use of the
physical verification process. The demand for fast turnaround time is
even more critical since the physical design is the last stage before
sending the layout to the foundries.
Abstract: Space Vector Pulse Width Modulation is popular for
variable frequency drives. The method has several advantages over
carried based PWM and is computation intensive. The
implementation of SVPWM for multilevel inverter requires special
attention and at the same time consumes considerable resources. Due
to faster processing power and reduced over all computational
burden, FPGAs are being investigated as an alternative for other
controllers. In this paper, a space vector PWM algorithm is
implemented using FPGA which requires less computational area and
is modular in structure. The algorithm is verified experimentally for
Neutral Point Clamped inverter using FPGA development board
xc3s5000-4fg900.
Abstract: This paper is aimed to study combustion characteristics
of low NOx burner using petroleum cokes as fuel. The petroleum coke,
which is produced through the oil refining process, is an attractive fuel
in terms of its high heating value and low price. But petroleum coke is
a challenging fuel because of its low volatile content, high sulfur and
nitrogen content, which give rise to undesirable emission
characteristics and low ignitability. Therefore, the research and
development regarding the petroleum coke burner is needed for
applying this industrial system. In this study, combustion and emission
characteristics of petroleum cokes burner are experimentally
investigated in an industrial steam boiler. The low NOx burner is
designed to control fuel and air mixing to achieve staged combustion,
which, in turn reduces both flame temperature and oxygen. Air
distribution ratio of triple staged air is optimized experimentally. The
result showed that NOx concentration is lowest when overfire air is
used, and the burner function at a fuel rich condition. That is, the
burner is operated at the equivalence ratio of 1.67 and overall
equivalence ratio including overfire air is kept 0.87.