Abstract: Ovshinsky initiated scientific research in the field of
amorphous and disordered materials that continues to this day. The
Ovshinsky Effect where the resistance of thin GST films is
significantly reduced upon the application of low voltage is of
fundamental importance in phase-change - random access memory
(PC-RAM) devices.GST stands for GdSbTe chalcogenide type
glasses.However, the Ovshinsky Effect is not without controversy.
Ovshinsky thought the resistance of GST films is reduced by the
redistribution of charge carriers; whereas, others at that time including
many PC-RAM researchers today argue that the GST resistance
changes because the GST amorphous state is transformed to the
crystalline state by melting, the heat supplied by external heaters. In
this controversy, quantum mechanics (QM) asserts the heat capacity of
GST films vanishes, and therefore melting cannot occur as the heat
supplied cannot be conserved by an increase in GST film
temperature.By precluding melting, QM re-opens the controversy
between the melting and charge carrier mechanisms. Supporting
analysis is presented to show that instead of increasing GST film
temperature, conservation proceeds by the QED induced creation of
photons within the GST film, the QED photons confined by TIR. QED
stands for quantum electrodynamics and TIR for total internal
reflection. The TIR confinement of QED photons is enhanced by the
fact the absorbedheat energy absorbed in the GST film is concentrated
in the TIR mode because of their high surface to volume ratio. The
QED photons having Planck energy beyond the ultraviolet produce
excitons by the photoelectric effect, the electrons and holes of which
reduce the GST film resistance.
Abstract: This paper presents the utilizing of ferroelectric
material on antenna application. There are two different ferroelectric
had been used on the proposed antennas which include of Barium
Strontium Titanate (BST) and Bismuth Titanate (BiT), suitable for
Access Points operating in the WLAN IEEE 802.11 b/g and WiMAX
IEEE 802.16 within the range of 2.3 GHz to 2.5 GHz application.
BST, which had been tested to own a dielectric constant of εr = 15
while BiT has a dielectric constant that higher than BST which is εr =
21 and both materials are in rectangular shaped. The influence of
various parameters on antenna characteristics were investigated
extensively using commercial electromagnetic simulations software
by Communication Simulation Technology (CST). From theoretical
analysis and simulation results, it was demonstrated that ferroelectric
material used have not only improved the directive emission but also
enhanced the radiation efficiency.
Abstract: In this paper we propose an enhanced equalization technique for multi-carrier code division multiple access (MC-CDMA). This method is based on the control of Equal Gain Combining (EGC) technique. Indeed, we introduce a new level changer to the EGC equalizer in order to adapt the equalization parameters to the channel coefficients. The optimal equalization level is, first, determined by channel training. The new approach reduces drastically the mutliuser interferences caused by interferes, without increasing the noise power. To compare the performances of the proposed equalizer, the theoretical analysis and numerical performances are given.
Abstract: Utilizing echoic intension and distribution from different organs and local details of human body, ultrasonic image can catch important medical pathological changes, which unfortunately may be affected by ultrasonic speckle noise. A feature preserving ultrasonic image denoising and edge enhancement scheme is put forth, which includes two terms: anisotropic diffusion and edge enhancement, controlled by the optimum smoothing time. In this scheme, the anisotropic diffusion is governed by the local coordinate transformation and the first and the second order normal derivatives of the image, while the edge enhancement is done by the hyperbolic tangent function. Experiments on real ultrasonic images indicate effective preservation of edges, local details and ultrasonic echoic bright strips on denoising by our scheme.
Abstract: The main issue discussed is on the role of education system in the process of nation building as a means in uniting different community ethnics which later on, hoped to shape the future ethnic relation of this country. It is generally known that political socialization experienced by each ethnic community has given birth to a vernacular education system, separated along the ethnic line. Every community shapes their own education system based on their respective mother tongue language, however all are based on the same curriculum. As a result the role of education as a uniting force is not significantly effective. Historically, it has been shown that government efforts to unite the country education system under the wing of national education system (national school) is not that successful since every community (Chinese) will defend the existence of their community education system because they want to spur their mother tongue language. The clash between national education system and vernacular education system is the root cause of stalemate in the ethnic relation in Malaysia and it always becomes a flash point when the issue is raised. The question now is what is the best solution to enhance the national education system in multiethnic Malaysia?
Abstract: The expression of LFA-1 diverges from the
physiological condition, thus active targeting carrier can provide the
benefits from difference into LFA-1 expression in various conditions.
Here, the selectivity of cIBR-conjugated nanoparticles (cIBR-NPs),
in terms of uptake, was investigated using PBMCs, Mixed PBMCMolt-
3 cells and Molt-3 cells. The expressions of LFA-1 on Molt-3
cells, from flow cytometry and Western blot, possessed the highest
level whereas PBMCs showed the lowest level. The kinetic uptake
profiles of cIBR-NPs were obtained by flow cytometry, which the
degree of cellular uptake presented a similar trend with the level of
LFA-1 indicating the influence of LFA-1 expression on the cellular
uptake of cIBR-NPs. The conformation of LFA-1 had a slight effect
on the cellular uptake of cIBR-NPs. Overall we demonstrated that
cIBR-NPs enhanced cellular uptake and improved the selectivity of
drug carriers to LFA-1 on the leukemia cells, which related with the
order of LFA-1 expression.
Abstract: This paper presents an approach which is based on the
use of supervised feed forward neural network, namely multilayer
perceptron (MLP) neural network and finite element method (FEM)
to solve the inverse problem of parameters identification. The
approach is used to identify unknown parameters of ferromagnetic
materials. The methodology used in this study consists in the
simulation of a large number of parameters in a material under test,
using the finite element method (FEM). Both variations in relative
magnetic permeability and electrical conductivity of the material
under test are considered. Then, the obtained results are used to
generate a set of vectors for the training of MLP neural network.
Finally, the obtained neural network is used to evaluate a group of
new materials, simulated by the FEM, but not belonging to the
original dataset. Noisy data, added to the probe measurements is used
to enhance the robustness of the method. The reached results
demonstrate the efficiency of the proposed approach, and encourage
future works on this subject.
Abstract: Breast carcinoma is the most common form of cancer
in women. Multicolour fluorescent in-situ hybridisation (m-FISH) is
a common method for staging breast carcinoma. The interpretation
of m-FISH images is complicated due to two effects: (i) Spectral
overlap in the emission spectra of fluorochrome marked DNA probes
and (ii) tissue autofluorescence. In this paper hyper-spectral images of
m-FISH samples are used and spectral unmixing is applied to produce
false colour images with higher contrast and better information
content than standard RGB images. The spectral unmixing is realised
by combinations of: Orthogonal Projection Analysis (OPA), Alterating
Least Squares (ALS), Simple-to-use Interactive Self-Modeling
Mixture Analysis (SIMPLISMA) and VARIMAX. These are applied
on the data to reduce tissue autofluorescence and resolve the spectral
overlap in the emission spectra. The results show that spectral unmixing
methods reduce the intensity caused by tissue autofluorescence by
up to 78% and enhance image contrast by algorithmically reducing
the overlap of the emission spectra.
Abstract: Cluster analysis is the name given to a diverse collection of techniques that can be used to classify objects (e.g. individuals, quadrats, species etc). While Kohonen's Self-Organizing Feature Map (SOFM) or Self-Organizing Map (SOM) networks have been successfully applied as a classification tool to various problem domains, including speech recognition, image data compression, image or character recognition, robot control and medical diagnosis, its potential as a robust substitute for clustering analysis remains relatively unresearched. SOM networks combine competitive learning with dimensionality reduction by smoothing the clusters with respect to an a priori grid and provide a powerful tool for data visualization. In this paper, SOM is used for creating a toroidal mapping of two-dimensional lattice to perform cluster analysis on results of a chemical analysis of wines produced in the same region in Italy but derived from three different cultivators, referred to as the “wine recognition data" located in the University of California-Irvine database. The results are encouraging and it is believed that SOM would make an appealing and powerful decision-support system tool for clustering tasks and for data visualization.
Abstract: Titanium nitride (TiN) has been synthesized using the
sheet plasma negative ion source (SPNIS). The parameters used for
its effective synthesis has been determined from previous
experiments and studies. In this study, further enhancement of the
deposition rate of TiN synthesis and advancement of the SPNIS
operation is presented. This is primarily achieved by the addition of
Sm-Co permanent magnets and a modification of the configuration in
the TiN deposition process. The magnetic enhancement is aimed at
optimizing the sputtering rate and the sputtering yield of the process.
The Sm-Co permanent magnets are placed below the Ti target for
better sputtering by argon. The Ti target is biased from –250V to –
350V and is sputtered by Ar plasma produced at discharge current of
2.5–4A and discharge potential of 60–90V. Steel substrates of
dimensions 20x20x0.5mm3 were prepared with N2:Ar volumetric
ratios of 1:3, 1:5 and 1:10. Ocular inspection of samples exhibit
bright gold color associated with TiN. XRD characterization
confirmed the effective TiN synthesis as all samples exhibit the (200)
and (311) peaks of TiN and the non-stoichiometric Ti2N (220) facet.
Cross-sectional SEM results showed increase in the TiN deposition
rate of up to 0.35μm/min. This doubles what was previously obtained
[1]. Scanning electron micrograph results give a comparative
morphological picture of the samples. Vickers hardness results gave
the largest hardness value of 21.094GPa.
Abstract: This paper estimates the economic values of
household preference for enhanced solid waste disposal services in
Malaysia. The contingent valuation (CV) method estimates an
average additional monthly willingness-to-pay (WTP) in solid waste
management charges of Ôé¼0.77 to 0.80 for improved waste disposal
services quality. The finding of a slightly higher WTP from the
generic CV question than that of label-specific, further reveals a
higher WTP for sanitary landfill, at Ôé¼0.90, than incineration, at Ôé¼0.63.
This suggests that sanitary landfill is a more preferred alternative.
The logistic regression estimation procedure reveals that household-s
concern of where their rubbish is disposed, age, ownership of house,
household income and format of CV question are significant factors
in influencing WTP.
Abstract: This paper presents a signal analysis process for
improving energy completeness based on the Hilbert-Huang
Transform (HHT). Firstly, the vibration signal of a DC Motor obtained
by employing an accelerometer is the model used to analyze the
signal. Secondly, the intrinsic mode functions (IMFs) and Hilbert
spectrum of the decomposed signal are obtained by applying HHT.
The results of the IMFs constituent and the original signal are
compared and the process of energy loss is discussed. Finally, the
differences between Wavelet Transform (WT) and HHT in analyzing
the signal are compared. The simulated results reveal the analysis
process based on HHT is advantageous for the enhancement of energy
completeness.
Abstract: In this paper we present an enhanced noise reduction method for robust speech recognition using Adaptive Gain Equalizer with Non linear Spectral Subtraction. In Adaptive Gain Equalizer method (AGE), the input signal is divided into a number of subbands that are individually weighed in time domain, in accordance to the short time Signal-to-Noise Ratio (SNR) in each subband estimation at every time instant. Instead of focusing on suppression the noise on speech enhancement is focused. When analysis was done under various noise conditions for speech recognition, it was found that Adaptive Gain Equalizer method algorithm has an obvious failing point for a SNR of -5 dB, with inadequate levels of noise suppression for SNR less than this point. This work proposes the implementation of AGE when coupled with Non linear Spectral Subtraction (AGE-NSS) for robust speech recognition. The experimental result shows that out AGE-NSS performs the AGE when SNR drops below -5db level.
Abstract: Low silica type X (LSX) Zeolite is one of useful
material in many manufacturing due to the advantage properties
including high surface area, stability, microporous crystalline
aluminosilicates and positive ion in an extra–framework. The LSX
was used rice husk silica source which obtained by leaching with
hydrochloric acid and calcination at 500 C. To improve the
synthesis method, the LSX was crystallizated in Teflon–lined
autoclave will expedite deceasing of the amorphous particles. The
mixed gel with composition of 5.5 Na2O : 1.65 K2O : Al2O3 : 2.2
SiO2 : 122 H2O was crystallized in different container
(Polypropylene bottom and Teflon–lined autoclave). The obtained
powder was characterized by X–ray diffraction (XRD), X–ray
fluorescence spectrometry, N2 adsorption-desorption analysis BET
surface area Scanning electron microscopy (SEM) and Fourier
transform infrared spectroscopy to justify the quality of zeolite. The
results showed the crystallized zeolite in Teflon lined autoclave has
102.8 nm of crystal size, 286 m2/g of surface area and fewer amounts
of round amorphous particles when compared with the crystallized
zeolite in Polypropylene.
Abstract: Steel surface defect detection is essentially one of
pattern recognition problems. Support Vector Machines (SVMs) are
known as one of the most proper classifiers in this application. In this
paper, we introduce a more accurate classification method by using
SVMs as our final classifier of the inspection system. In this scheme,
multiclass classification task is performed based on the "one-againstone"
method and different kernels are utilized for each pair of the
classes in multiclass classification of the different defects.
In the proposed system, a decision tree is employed in the first
stage for two-class classification of the steel surfaces to "defect" and
"non-defect", in order to decrease the time complexity. Based on
the experimental results, generated from over one thousand images,
the proposed multiclass classification scheme is more accurate than
the conventional methods and the overall system yields a sufficient
performance which can meet the requirements in steel manufacturing.
Abstract: In this contribution a newly developed e-learning environment is presented, which incorporates Intelligent Agents and Computational Intelligence Techniques. The new e-learning environment is constituted by three parts, the E-learning platform Front-End, the Student Questioner Reasoning and the Student Model Agent. These parts are distributed geographically in dispersed computer servers, with main focus on the design and development of these subsystems through the use of new and emerging technologies. These parts are interconnected in an interoperable way, using web services for the integration of the subsystems, in order to enhance the user modelling procedure and achieve the goals of the learning process.
Abstract: techniques are examined to overcome the
performance degradation caused by the channel dispersion using
slow frequency hopping (SFH) with dynamic frequency hopping
(DFH) pattern adaptation. In DFH systems, the frequency slots are
selected by continuous quality monitoring of all frequencies available
in a system and modification of hopping patterns for each individual
link based on replacing slots which its signal to interference ratio
(SIR) measurement is below a required threshold. Simulation results
will show the improvements in BER obtained by DFH in comparison
with matched frequency hopping (MFH), random frequency hopping
(RFH) and multi-carrier code division multiple access (MC-CDMA)
in multipath slowly fading dispersive channels using a generalized
bandpass two-path transfer function model, and will show the
improvement obtained according to the threshold selection.
Abstract: We identify clawback triggers from firms- proxy
statements (Form DEF 14A) and use the likelihood of restatements to
proxy for financial reporting quality. Based on a sample of 578 U.S.
firms that voluntarily adopt clawback provisions during 2003-2009,
when restatement-based triggers could be decomposed into two types:
fraud and unintentional error, and we do observe the evidence that
using fraud triggers is associated with high financial reporting quality.
The findings support that fraud triggers can enhance deterrent effect of
clawback provision by establishing a viable disincentive against fraud,
misconduct, and otherwise harmful acts. These results are robust to
controlling for the compensation components, to different sample
specifications and to a number of sensitivity.
Abstract: The cDNA encoding the 326 amino acids of a Class I
basic chitinase gene from Leucaena leucocephala de Wit (KB3,
Genbank accession: AAM49597) was cloned under the control of
CaMV35S promoter in pCAMBIA 1300 and transferred to
Koshihikari. Calli of Koshihikari rice was transformed with
agrobacterium with this construct expressing the chitinase and β-
glucouronidase (GUS). The frequencies of calli 90 % has been
obtained from rice seedlings cultured on NB medium. The high
regeneration frequencies, 74% was obtained from calli cultured on
regeneration medium containing 4 mg/l BAP, and 7 g/l phytagel at
25°C. Various factors were studied in order to establish a procedure
for the transformation of Koshihikari Agrobacterium tumefaciens.
Supplementation of 50 mM acetosyringone to the medium during
coculivation was important to enhance the frequency to transient
transformation. The 4 week-old scutellum-derived calli were
excellent starting materials. Selection medium based on NB medium
supplement with 40 mg/l hygromycin and 400 mg/l cefotaxime were
an optimized medium for selection of transformed rice calli. The
percentage of transformation 70 was obtained. Recombinant calli and
regenerated rice plants were checked the expression of chitinase and
gus by PCR, northern blot gel, southern blot gel, and gus assay.
Chitinase and gus were expressed in all parts of recombinant rice.
The rice line expressing the KB3 chiitnase was more resistant to the
blast fungus Fusarium monoliforme than control line.
Abstract: Histogram equalization is often used in image enhancement, but it can be also used in auto exposure. However, conventional histogram equalization does not work well when many pixels are concentrated in a narrow luminance range.This paper proposes an auto exposure method based on 2-way histogram equalization. Two cumulative distribution functions are used, where one is from dark to bright and the other is from bright to dark. In this paper, the proposed auto exposure method is also designed and implemented for image signal processors with full-HD images.