Abstract: Electronic nose (array of chemical sensors) are widely
used in food industry and pollution control. Also it could be used to
locate or detect the direction of the source of emission odors. Usually
this task is performed by electronic nose (ENose) cooperated with
mobile vehicles, but when a source is instantaneous or surrounding is
hard for vehicles to reach, problem occurs. Thus a method for
stationary ENose to detect the direction of the source and locate the
source will be required. A novel method which uses the ratio between
the responses of different sensors as a discriminant to determine the
direction of source in natural wind surroundings is presented in this
paper. The result shows that the method is accurate and easily to be
implemented. This method could be also used in movably, as an
optimized algorithm for robot tracking source location.
Abstract: The paper presents the design of a mini-UAV attitude
controller using the backstepping method. Starting from the nonlinear
dynamic equations of the mini-UAV, by using the backstepping
method, the author of this paper obtained the expressions of the
elevator, rudder and aileron deflections, which stabilize the UAV, at
each moment, to the desired values of the attitude angles. The attitude
controller controls the attitude angles, the angular rates, the angular
accelerations and other variables that describe the UAV longitudinal
and lateral motions. To design the nonlinear controller, by using the
backstepping technique, the nonlinear equations and the Lyapunov
analysis have been directly used. The designed controller has been
implemented in Matlab/Simulink environment and its effectiveness
has been tested with a campaign of numerical simulations using data
from the UAV flight tests. The obtained results are very good and
they are better than the ones found in previous works.
Abstract: It is important for an autonomous mobile robot to know
where it is in any time in an indoor environment. In this paper, we
design a relative self-localization algorithm. The algorithm compare
the interest point in two images and compute the relative displacement
and orientation to determent the posture. Firstly, we use the SURF
algorithm to extract the interest points of the ceiling. Second, in order
to reduce amount of calculation, a replacement SURF is used to extract
orientation and description of the interest points. At last, according to
the transformation of the interest points in two images, the relative
self-localization of the mobile robot will be estimated greatly.
Abstract: We present a novel scheme to recognize isolated speech
signals using certain statistical parameters derived from those signals.
The determination of the statistical estimates is based on extracted
signal information rather than the original signal information in
order to reduce the computational complexity. Subtle details of
these estimates, after extracting the speech signal from ambience
noise, are first exploited to segregate the polysyllabic words from
the monosyllabic ones. Precise recognition of each distinct word is
then carried out by analyzing the histogram, obtained from these
information.
Abstract: In this study, fuzzy rule-based classifier is used for the
diagnosis of congenital heart disease. Congenital heart diseases are
defined as structural or functional heart disease. Medical data sets
were obtained from Pediatric Cardiology Department at Selcuk
University, from years 2000 to 2003. Firstly, fuzzy rules were
generated by using medical data. Then the weights of fuzzy rules
were calculated. Two different reasoning methods as “weighted vote
method" and “singles winner method" were used in this study. The
results of fuzzy classifiers were compared.
Abstract: This work deals with the design of the robotic assembly
system for the roller clamps. The task is characterized by high speed,
high yield and safety engagement. This paper describes the design of
different parts of an automated high speed machine to assemble the
parts of roller clamps. The roller clamp robotic assembly system
performs various processes in the assembly line which include clamp
body and roller feeding, inserting the roller into the clamp body, and
dividing the rejected clamp and successfully assembled clamp into
their own tray. The electrical/electronics design of the machine is
discussed. The target is to design a cost effective, minimum
maintenance and high speed machine for the industry applications.
Abstract: In this paper a polymer electrolyte membrane (PEM)
fuel cell power system including burner, steam reformer, heat
exchanger and water heater has been considered to meet the
electrical, heating, cooling and domestic hot water loads of
residential building which in Tehran. The system uses natural gas as
fuel and works in CHP mode. Design and operating conditions of a
PEM fuel cell system is considered in this study. The energy
requirements of residential building and the number of fuel cell
stacks to meet them have been estimated. The method involved
exergy analysis and entropy generation thorough the months of the
year. Results show that all the energy needs of the building can be
met with 12 fuel cell stacks at a nominal capacity of 8.5 kW. Exergy
analysis of the CHP system shows that the increase in the ambient air
temperature from 1oC to 40oC, will have an increase of entropy
generation by 5.73%.Maximum entropy generates for 15 hour in 15th
of June and 15th of July is estimated to amount at 12624 (kW/K).
Entropy generation of this system through a year is estimated to
amount to 1004.54 GJ/k.year.
Abstract: This paper invites to dialogue and reflections on
innovation and entrepreneurship by presenting concepts of innovation
leading to the introduction of a complex theoretical framework;
Cooperative Innovation (CO-IN). CO-IN is a didactic model
enhancing and scaffolding processes of cooperation creating
innovation drawing on a Scandinavian tradition.
CO-IN is based on a cross-sectorial and multidisciplinary
approach. We introduce the concept of complementarity to help
capture the validity of diversity and we suggest the concept of “the
space in between" to understand the creation of identity as a
collective mind. We see dialogue and the use of multi modal
techniques as essential tools for conceptualizations giving possibility
for clarification of the complexity and diversity leading to decision
making based on knowledge as commons.
We introduce the didactic design and present our empirical
findings from an innovation workshop in Argentina. In a final
paragraph we reflect on the design as a support of the development of
common ground, collective mind and collective action and the
creation of knowledge as commons to facilitate innovation and
entrepreneurship.
Abstract: The overriding goal of software engineering is to
provide a high quality system, application or a product. To achieve
this goal, software engineers must apply effective methods coupled
with modern tools within the context of a mature software process
[2]. In addition, it is also must to assure that high quality is realized.
Although many quality measures can be collected at the project
levels, the important measures are errors and defects. Deriving a
quality measure for reusable components has proven to be
challenging task now a days. The results obtained from the study are
based on the empirical evidence of reuse practices, as emerged from
the analysis of industrial projects. Both large and small companies,
working in a variety of business domains, and using object-oriented
and procedural development approaches contributed towards this
study. This paper proposes a quality metric that provides benefit at
both project and process level, namely defect removal efficiency
(DRE).
Abstract: In order to survive in a rapidly changing business environment, Malaysian business firms must improve their own business practices and procedures. This paper describes the impact of Critical Success Factors (CSFs) during the Enterprise Resource Planning (ERP) system implementations using the responses from 151 organizations that completed or are in the process of completing an ERP implementation and identifying the key benefits of ERP implementation in the firm. The importance of these factors was investigated within Malaysian companies using questionnaire survey method. Our results provide advice to management on how best to utilize their limited resources to choose those CSFs that are most likely to have an impact upon the implementation of the ERP system.
Abstract: A model of (4, 4) single-walled boron-nitride nanotube as a representative of armchair boron-nitride nanotubes studied. At first the structure optimization performed and then Nuclear Magnetic Resonance parameters (NMR) by Density Functional Theory (DFT) method at 11B and 15N nuclei calculated. Resulted parameters evaluation presents electrostatic environment heterogeneity along the nanotube and especially at the ends but the nuclei in a layer feel the same electrostatic environment. All of calculations carried out using Gaussian 98 Software package.
Abstract: Conventional industrial monitoring systems are
tedious, inefficient and the at times integrity of the data is
unreliable. The objective of this system is to monitor industrial
processes specifically the fluid level which will measure the
instantaneous fluid level parameter and respond by text
messaging the exact value of the parameter to the user when
being enquired by a privileged access user. The development of
the embedded program code and the circuit for fluid level
measuring are discussed as well. Suggestions for future
implementations and efficient remote monitoring works are
included.
Abstract: In this paper we present the modeling, design, and
experimental testing of a nerve cuff multi-electrode system for
diameter-selective vagus nerve stimulation.
The multi-electrode system contained ninety-nine platinum
electrodes embedded within a self-curling spiral silicone sheet. The
electrodes were organized in a matrix having nine parallel groups,
each containing eleven electrodes.
Preliminary testing of the nerve cuff was performed in an isolated
segment of a swinish left cervical vagus nerve. For selective vagus
nerve stimulation, precisely defined current quasitrapezoidal,
asymmetric and biphasic stimulating pulses were applied to
preselected locations along the left vagus segment via appointed
group of three electrodes within the cuff. Selective stimulation was
obtained by anodal block. However, these pulses may not be safe for
a long-term application because of a frequently used high imbalance
between the cathodic and anodic part of the stimulating pulse.
Preliminary results show that the cuff was capable of exciting A
and B-fibres, and, that for a certain range of parameters used in
stimulating pulses, the contribution of A-fibres to the CAP was
slightly reduced and the contribution of B-fibres was slightly larger.
Results also showed that measured CAPs are not greatly
influenced by the imbalance between a charge Qc injected in cathodic
and Qa in anodic phase of quasitrapezoidal, asymmetric and biphasic
pulses.
Abstract: This paper describes the development of a WLAN
propagation model, using Spectral Analyzer measurements. The
signal is generated by two Access Points (APs) on the base floor at
the administrative Communication School of ESPOL building. In
general, users do not have a Q&S reference about a wireless network;
however, this depends on the level signal as a function of frequency,
distance and other path conditions between receiver and transmitter.
Then, power density of the signal decrease as it propagates through
space and data transfer rate is affected. This document evaluates and
implements empirical mathematical formulation for the
characterization of WLAN radio wave propagation on two aisles of
the building base floor.
Abstract: The main objective of this study was to demonstrate that differentiation of infected and vaccinated animals (DIVA) strategy using different ELISA tests is possible when a subunit vaccine (Haemagglutinin protein) is used to prevent Avian influenza. Special emphasis was placed on the differentiation in the serological response to different components of the AIV (Nucleoprotein, Neuraminidase, Haemagglutinin, Nucleocapsid) between chickens that were vaccinated with a whole virus kill vaccine and recombinant vaccine. Furthermore, the potential use of this DIVA strategy using ELISA assays to detect Neuraminidase 1 (N1) was analyzed as strategy in countries where the field virus is H5N1 and the vaccine used is formulated with H5N2. Detection of AIV-s antibodies to any component in serum was negative for all animals on the study days 0-13. At study day 14 the titers of antibodies against Nucleoprotein (NP) and Nucleocapsid (NC) rose in the experimental groups vaccinated with Volvac® AI KV and were negatives during all the trial in the experimental groups vaccinated with a subunit H5; significant statistically differences were observed between these groups (p < 0.05). The seroconversion either Haemagglutinin or Neuraminidase was evident after 21 days post-vaccination in the experimental groups vaccinated with the respective viral fraction. Regarding the main aim of this study and according with the results that were obtained, use a combination of different ELISA test as a DIVA strategy is feasible when the vaccination is carry out with a subunit H5 vaccine. Also is possible to use the ELISA kit to detect Neuraminidase (either N1 or N2) as a DIVA concept in countries where H5N1 is present and the vaccination programs are done with H5N2 vaccine.
Abstract: Any decision-making is based on certain theory. Taking
the public rental housing in Chongqing municipality as an example,
this essay states that the stakeholder theory can provide innovative
criteria and evaluation methods for Public Private Partnership (PPP)
projects. It gives an analysis of how to choose decision-making criteria
for different stakeholders in the PPP model and what measures to take
to meet the criteria to form “symbiotic" decision-making mode
through contracts and to boost the application of PPP model in
large-scale public programs in China.
Abstract: The following paper shows an interactive tool which
main purpose is to teach how to play a flute. It consists of three
stages the first one is the instruction and teaching process through a
software application, the second is the practice part when the user
starts to play the flute (hardware specially designed for this
application) this flute is capable of capturing how is being played the
flute and the final stage is the one in which the data captured are sent
to the software and the user is evaluated in order to give him / she a
correction or an acceptance
Abstract: This paper proposes a solution to the motion planning
and control problem of car-like mobile robots which is required to
move safely to a designated target in a priori known workspace
cluttered with swarm of boids exhibiting collective emergent
behaviors. A generalized algorithm for target convergence and
swarm avoidance is proposed that will work for any number of
swarms. The control laws proposed in this paper also ensures
practical stability of the system. The effectiveness of the proposed
control laws are demonstrated via computer simulations of an
emergent behavior.
Abstract: The objective of the paper is twofold. First, to develop a
formal framework for planning for mobile agents. A logical language
based on a temporal logic is proposed that can express a type of
tasks which often arise in network management. Second, to design a
planning algorithm for such tasks. The aim of this paper is to study
the importance of finding plans for mobile agents. Although there
has been a lot of research in mobile agents, not much work has been
done to incorporate planning ideas for such agents. This paper makes
an attempt in this direction. A theoretical study of finding plans for
mobile agents is undertaken. A planning algorithm (based on the
paradigm of mobile computing) is proposed and its space, time, and
communication complexity is analyzed. The algorithm is illustrated
by working out an example in detail.
Abstract: This work is focused on the numerical prediction of the fracture resistance of a flat stiffened panel made of the aluminium alloy 2024 T3 under a monotonic traction condition. The performed numerical simulations have been based on the micromechanical Gurson-Tvergaard (GT) model for ductile damage. The applicability of the GT model to this kind of structural problems has been studied and assessed by comparing numerical results, obtained by using the WARP 3D finite element code, with experimental data available in literature. In the sequel a home-made procedure is presented, which aims to increase the residual strength of a cracked stiffened aluminum panel and which is based on the stochastic design improvement (SDI) technique; a whole application example is then given to illustrate the said technique.