Abstract: The paper compares different channel models used for
modeling Broadband Power-Line Communication (BPLC) system.
The models compared are Zimmermann and Dostert, Philipps,
Anatory et al and Anatory et al generalized Transmission Line (TL)
model. The validity of each model was compared in time domain
with ATP-EMTP software which uses transmission line approach. It
is found that for a power-line network with minimum number of
branches all the models give similar signal/pulse time responses
compared with ATP-EMTP software; however, Zimmermann and
Dostert model indicates the same amplitude but different time delay.
It is observed that when the numbers of branches are increased only
generalized TL theory approach results are comparable with ATPEMTP
results. Also the Multi-Carrier Spread Spectrum (MC-SS)
system was applied to check the implication of such behavior on the
modulation schemes. It is observed that using Philipps on the
underground cable can predict the performance up to 25dB better
than other channel models which can misread the actual performance
of the system. Also modified Zimmermann and Dostert under
multipath can predict a better performance of about 5dB better than
the actual predicted by Generalized TL theory. It is therefore
suggested for a realistic BPLC system design and analyses the model
based on generalized TL theory be used.
Abstract: In this paper the complete rotor system including
elastic shaft with distributed mass, allowing for the effects of oil film
in bearings. Also, flexibility of foundation is modeled. As a whole
this article is a relatively complete research in modeling and
vibration analysis of rotor considering gyroscopic effect, damping,
dependency of stiffness and damping coefficients on frequency and
solving the vibration equations including these parameters. On the
basis of finite element method and utilizing four element types
including element of shaft, disk, bearing and foundation and using
MATLAB, a computer program is written. So the responses in
several cases and considering different effects are obtained. Then the
results are compared with each other, with exact solutions and results
of other papers.
Abstract: Almost all Libyan industries (both private and public) have struggled with many difficulties during the past three decades due to many problems. These problems have created a strongly negative impact on the productivity and utilization of many companies within Libya. This paper studies the current awareness and implementation levels of Just-In-Time (JIT) within the Libyan Textile private industry. A survey has been applied in this study using an intensive detailed questionnaire. Based on the analysis of the survey responses, the results show that the management body within the surveyed companies has a modest strategy towards most of the areas that are considered as being very crucial in any successful implementation of JIT. The results also show a variation within the implementation levels of the JIT elements as these varies between Low and Acceptable levels. The paper has also identified limitations within the investigated areas within this industry, and has pointed to areas where senior managers within the Libyan textile industry should take immediate actions in order to achieve effective implementation of JIT within their companies.
Abstract: Several models have been introduced so far for single
electron box, SEB, which all of them were restricted to DC response
and or low temperature limit. In this paper we introduce a new time
dependent, high temperature analytical model for SEB for the first
time. DC behavior of the introduced model will be verified against
SIMON software and its time behavior will be verified against a
newly published paper regarding step response of SEB.
Abstract: In this paper the design of maximally flat linear phase
finite impulse response (FIR) filters is considered. The problem is
handled with totally two different approaches. The first one is
completely deterministic numerical approach where the problem is
formulated as a Linear Complementarity Problem (LCP). The other
one is based on a combination of Markov Random Fields (MRF's)
approach with messy genetic algorithm (MGA). Markov Random
Fields (MRFs) are a class of probabilistic models that have been
applied for many years to the analysis of visual patterns or textures.
Our objective is to establish MRFs as an interesting approach to
modeling messy genetic algorithms. We establish a theoretical result
that every genetic algorithm problem can be characterized in terms of
a MRF model. This allows us to construct an explicit probabilistic
model of the MGA fitness function and introduce the Ising MGA.
Experimentations done with Ising MGA are less costly than those
done with standard MGA since much less computations are involved.
The least computations of all is for the LCP. Results of the LCP,
random search, random seeded search, MGA, and Ising MGA are
discussed.
Abstract: A fully on-chip low drop-out (LDO) voltage regulator with 100pF output load capacitor is presented. A novel frequency compensation scheme using current buffer is adopted to realize single dominant pole within the unit gain frequency of the regulation loop, the phase margin (PM) is at least 50 degree under the full range of the load current, and the power supply rejection (PSR) character is improved compared with conventional Miller compensation. Besides, the differentiator provides a high speed path during the load current transient. Implemented in 0.18μm CMOS technology, the LDO voltage regulator provides 100mA load current with a stable 1.8V output voltage consuming 80μA quiescent current.
Abstract: Multiprocessor task scheduling is a NP-hard problem and Genetic Algorithm (GA) has been revealed as an excellent technique for finding an optimal solution. In the past, several methods have been considered for the solution of this problem based on GAs. But, all these methods consider single criteria and in the present work, minimization of the bi-criteria multiprocessor task scheduling problem has been considered which includes weighted sum of makespan & total completion time. Efficiency and effectiveness of genetic algorithm can be achieved by optimization of its different parameters such as crossover, mutation, crossover probability, selection function etc. The effects of GA parameters on minimization of bi-criteria fitness function and subsequent setting of parameters have been accomplished by central composite design (CCD) approach of response surface methodology (RSM) of Design of Experiments. The experiments have been performed with different levels of GA parameters and analysis of variance has been performed for significant parameters for minimisation of makespan and total completion time simultaneously.
Abstract: Over the past few years, companies in developing
countries have implemented enterprise resource planning (ERP)
systems. Regardless of the various benefits of the ERP system, its
adoption and implementation have not been without problems. Many
companies have assigned considerable organizational resources to
their ERP projects, but have encountered unexpected challenges.
Neglecting a number of important factors in ERP projects might lead
to failure instead of success. User satisfaction is among those factors
that has a major influence on ERP implementation success. So, this
paper intends to investigate the key factors that create ERP users-
satisfaction and to discover whether ERP users- satisfaction varies
among different users- profiles. The study was conducted using a
survey questionnaire which was distributed to ERP users in Iranian
organizations. A total of 384 responses were collected and analyzed.
The findings indicated that younger ERP users tend to be more
satisfied with ERP systems. Furthermore, ERP users with more
experiences in IT and also more educated users have more
satisfaction with ERP softwares. However, the study found no
satisfaction differences between men and women users.
Abstract: This research focuses on the use of a recommender
system in decision support by means of a used car dealer case study
in Bangkok Metropolitan. The goal is to develop an effective used car
purchasing system for dealers based on the above premise. The
underlying principle rests on content-based recommendation from a
set of usability surveys. A prototype was developed to conduct
buyers- survey selected from 5 experts and 95 general public. The
responses were analyzed to determine the mean and standard
deviation of buyers- preference. The results revealed that both groups
were in favor of using the proposed system to assist their buying
decision. This indicates that the proposed system is meritorious to
used car dealers.
Abstract: Discrimination in employment has its wider social and
economic consequences other than mere violating a basic human
right. Discrimination involves treating people differently because of
certain grounds such as race, color, or sex, which results in the
impairment of equality of opportunity and treatment. As an essential
part of promoting decent work, combating discrimination through the
principle of non-discrimination has been established by the
International Labor Organization (ILO) through the Declaration on
Fundamental Principles and Rights at Work 1998. Considering
elimination of discrimination in employment as a core labor standard,
member states are expected to respect, promote and implement it to
their national laws and policies. Being a member state, Malaysia has
to position herself align with this international requirement. The
author discusses the related convention together with Malaysia-s
responses on the matter. At the closing stage, the prospect of
Malaysia is presumed taking into account of the current positions and
reports submitted to the ILO.
Abstract: This paper presents results obtained from the
numerical solution for the flow past an oscillating circular cylinder at
Reynolds number of 200. The frequency of oscillation was fixed to
the vortex shedding frequency from a fixed cylinder, f0, while the
amplitudes of oscillations were varied from to 1.1a, where a
represents the radius of the cylinder. The response of the flow
through the fluid forces acting on the surface of the cylinder are
investigated. The lock-on phenomenon is captured at low oscillation
amplitudes.
Abstract: The C3 plants are frequently suffering from exposure
to high temperature stress which limits the growth and yield of these
plants. This study seeks to clarify the physiological mechanisms of
heat tolerance in relation to oxidative stress in C3 species. Fifteen C3
species were exposed to prolonged moderately high temperature
stress 36/30°C for 40 days in a growth chamber. Chlorophyll
fluorescence (Fv/Fm) showed great difference among species at 40
days of the stress. The species showed decreases in Fv/Fm and
increases in malondialdehyde (MDA) content under stress condition
as well as negative correlation between Fv/Fm and MDA (r = -0.61*)
at 40 days of the stress. Hydrogen peroxide (H2O2) content before
and after stress in addition to its response under stress showed great
differences among species. The results suggest that the difference in
heat tolerance among C3 species is closely associated with the ability
to suppress oxidative damage but not with the content of reactive
oxygen species (ROS) which is regulated by complex network.
Abstract: Laser soldering is based on applying some soldering material (albumin) onto the approximated edges of the cut and heating the solder (and the underlying tissues) by a laser beam. Endogenous and exogenous materials such as indocyanine green (ICG) are often added to solders to enhance light absorption. Gold nanoshells are new materials which have an optical response dictated by the plasmon resonance. The wavelength at which the resonance occurs depends on the core and shell sizes, allowing nanoshells to be tailored for particular applications. The purposes of this study was use combination of ICG and different concentration of gold nanoshells for skin tissue soldering and also to examine the effect of laser soldering parameters on the properties of repaired skin. Two mixtures of albumin solder and different combinations of ICG and gold nanoshells were prepared. A full thickness incision of 2×20 mm2 was made on the surface and after addition of mixtures it was irradiated by an 810nm diode laser at different power densities. The changes of tensile strength σt due to temperature rise, number of scan (Ns), and scan velocity (Vs) were investigated. The results showed at constant laser power density (I), σt of repaired incisions increases by increasing the concentration of gold nanoshells in solder, Ns and decreasing Vs. It is therefore important to consider the tradeoff between the scan velocity and the surface temperature for achieving an optimum operating condition. In our case this corresponds to σt =1800 gr/cm2 at I~ 47 Wcm-2, T ~ 85ºC, Ns =10 and Vs=0.3mms-1.
Abstract: The adsorption of simulated aqueous solution containing textile remazol reactive dye, namely Red 3BS by palm shell activated carbon (PSAC) as adsorbent was carried out using Response Surface Methodology (RSM). A Box-Behnken design in three most important operating variables; initial dye concentration, dosage of adsorbent and speed of impeller was employed for experimental design and optimization of results. The significance of independent variables and their interactions were tested by means of the analysis of variance (ANOVA) with 95% confidence limits. Model indicated that with the increasing of dosage and speed give the result of removal up to 90% with the capacity uptake more than 7 mg/g. High regression coefficient between the variables and the response (R-Sq = 93.9%) showed of good evaluation of experimental data by polynomial regression model.
Abstract: A 7-step method (with 25 sub-steps) to assess risk of
air pollutants is introduced. These steps are: pre-considerations,
sampling, statistical analysis, exposure matrix and likelihood, doseresponse
matrix and likelihood, total risk evaluation, and discussion
of findings. All mentioned words and expressions are wellunderstood;
however, almost all steps have been modified, improved,
and coupled in such a way that a comprehensive method has been
prepared. Accordingly, the SADRA (Statistical Analysis-Driven Risk
Assessment) emphasizes extensive and ongoing application of
analytical statistics in traditional risk assessment models. A Sulfur
Dioxide case study validates the claim and provides a good
illustration for this method.
Abstract: Social interest and demand on Home-Network has
been increasing greatly. Although various services are being
introduced to respond to such demands, they can cause serious
security problems when linked to the open network such as Internet.
This paper reviews the security requirements to protect the service
users with assumption that the Home-Network environment is
connected to Internet and then proposes the security model based on
the requirement. The proposed security model can satisfy most of the
requirements and further can be dynamically applied to the future
ubiquitous Home-Networks.
Abstract: Safety of bus journey is a fundamental concern. Risk of injuries and fatalities is severe when bus superstructure fails during rollover accident. Adequate design and sufficient strength of bus superstructure can reduce the number of injuries and fatalities. This paper deals with structural analysis of bus superstructure undergoes rollover event. Several value of mass will be varied in multiple simulations. The purpose of this work is to analyze structural response of bus superstructure in terms of deformation, stress and strain under several loading and constraining conditions. A complete bus superstructure with forty four passenger-s capability was developed using finite element analysis software. Simulations have been conducted to observe the effect of total mass of bus on the strength of superstructure. These simulations are following United Nation Economic Commission of Europe regulation 66 which focuses on strength of large vehicle superstructure. Validation process had been done using simple box model experiment and results obtained are comparing with simulation results. Inputs data from validation process had been used in full scale simulation. Analyses suggested that, the failure of bus superstructure during rollover situation is basically dependent on the total mass of bus and on the strength of bus superstructure.
Abstract: A mathematical model of the surface roughness
has been developed by using response surface methodology
(RSM) in grinding of AISI D2 cold work tool steels. Analysis
of variance (ANOVA) was used to check the validity of the
model. Low and high value for work speed and feed rate are
decided from design of experiment. The influences of all
machining parameters on surface roughness have been
analyzed based on the developed mathematical model. The
developed prediction equation shows that both the feed rate
and work speed are the most important factor that influences
the surface roughness. The surface roughness was found to be
the lowers with the used of low feed rate and low work speed.
Accuracy of the best model was proved with the testing data.
Abstract: As the world move to the accomplishment of Performance Based Engineering philosophies in seismic design of Civil Engineering structures, new seismic design provisions require Structural Engineers to perform both static and dynamic analysis for the design of structures. While Linear Equivalent Static Analysis is performed for regular buildings up to 90m height in zone I and II, Dynamic Analysis should be performed for regular and irregular buildings in zone IV and V. Dynamic Analysis can take the form of a dynamic Time History Analysis or a linear Response Spectrum Analysis. In present study, Multi-storey irregular buildings with 20 stories have been modeled using software packages ETABS and SAP 2000 v.15 for seismic zone V in India. This paper also deals with the effect of the variation of the building height on the structural response of the shear wall building. Dynamic responses of building under actual earthquakes, EL-CENTRO 1949 and CHI-CHI Taiwan 1999 have been investigated. This paper highlights the accuracy and exactness of Time History analysis in comparison with the most commonly adopted Response Spectrum Analysis and Equivalent Static Analysis.
Abstract: The artificial intelligent controller in power system
plays as most important rule for many applications such as system
operation and its control specially Load Frequency Controller (LFC).
The main objective of LFC is to keep the frequency and tie-line power
close to their decidable bounds in case of disturbance. In this paper,
parallel fuzzy PI adaptive with conventional PD technique for Load
Frequency Control system was proposed. PSO optimization method
used to optimize both of scale fuzzy PI and tuning of PD. Two equal
interconnected power system areas were used as a test system.
Simulation results show the effectiveness of the proposed controller
compared with different PID and classical fuzzy PI controllers in terms
of speed response and damping frequency.