Abstract: The principal objective of a water treatment plant is to
produce water that satisfies a set of drinking water quality standards
at a reasonable price to the consumers. The gravel-bed flocculator
provide a simple and inexpensive design for flocculation in small
water treatment plants (less than 5000 m3/day capacity). The packed
bed of gravel provides ideal conditions for the formation of compact
settleable flocs because of continuous recontact provided by the
sinuous flow of water through the interstices formed by the gravel.
The field data which were obtained from the operation of the
water supply treatment unit cover the physical, chemical and
biological water qualities of the raw and settled water as obtained by
the operation of the treatment unit. The experiments were carried out
with the aim of assessing the efficiency of the gravel filter in
removing the turbidity, pathogenic bacteria, from the raw water. The
water treatment plant, which was constructed for the treatment of
river water, was in principle a rapid sand filter.
The results show that the average value of the turbidity level of
the settled water was 4.83 NTU with a standard deviation of turbidity
2.893 NTU. This indicated that the removal efficiency of the
sedimentation tank (gravel filter) was about 67.8 %. for pH values
fluctuated between 7.75 and 8.15, indicating the alkaline nature of
the raw water of the river Shatt Al-Hilla, as expected. Raw water pH
is depressed slightly following alum coagulation. The pH of the
settled water ranged from 7.75 to a maximum of 8.05.
The bacteriological tests which were carried out on the water
samples were: total coliform test, E-coli test, and the plate count test.
In each test the procedure used was as outlined in the Standard
Methods for the Examination of Water and Wastewater (APHA,
AWWA, and WPCF, 1985). The gravel filter exhibit a low
performance in removing bacterial load. The percentage bacterial
removal, which is maximum for total plate count (19%) and
minimum for total coliform (16.82%).
Abstract: In this paper, a new BiCMOS CCII and CCCII,
capable of operate at ±0.5V and having wide dynamic range with
achieved bandwidth of 480MHz and 430MHz respectively have been
proposed. The structures have been found to be insensitive to the
threshold voltage variations. The proposed circuits are suitable for
implementation using 0.25μm BiCMOS technology. Pspice
simulations confirm the performance of the proposed structures.
Abstract: This article presents new current-mode oscillator circuits using CDTAs which is designed from block diagram. The proposed circuits consist of two CDTAs and two grounded capacitors. The condition of oscillation and the frequency of oscillation can be adjusted by electronic method. The circuits have high output impedance and use only grounded capacitors without any external resistor which is very appropriate to future development into an integrated circuit. The results of PSPICE simulation program are corresponding to the theoretical analysis.
Abstract: A 7-step method (with 25 sub-steps) to assess risk of
air pollutants is introduced. These steps are: pre-considerations,
sampling, statistical analysis, exposure matrix and likelihood, doseresponse
matrix and likelihood, total risk evaluation, and discussion
of findings. All mentioned words and expressions are wellunderstood;
however, almost all steps have been modified, improved,
and coupled in such a way that a comprehensive method has been
prepared. Accordingly, the SADRA (Statistical Analysis-Driven Risk
Assessment) emphasizes extensive and ongoing application of
analytical statistics in traditional risk assessment models. A Sulfur
Dioxide case study validates the claim and provides a good
illustration for this method.
Abstract: Social interest and demand on Home-Network has
been increasing greatly. Although various services are being
introduced to respond to such demands, they can cause serious
security problems when linked to the open network such as Internet.
This paper reviews the security requirements to protect the service
users with assumption that the Home-Network environment is
connected to Internet and then proposes the security model based on
the requirement. The proposed security model can satisfy most of the
requirements and further can be dynamically applied to the future
ubiquitous Home-Networks.
Abstract: A new paradigm for software design and development models software by its business process, translates the model into a process execution language, and has it run by a supporting execution engine. This process-oriented paradigm promotes modeling of software by less technical users or business analysts as well as rapid development. Since business process models may be shared by different organizations and sometimes even by different business domains, it is interesting to apply a technique used in traditional software component technology to design reusable business processes. This paper discusses an approach to apply a technique for software component fabrication to the design of process-oriented software units, called process components. These process components result from decomposing a business process of a particular application domain into subprocesses with an aim that the process components can be reusable in different process-based software models. The approach is quantitative because the quality of process component design is measured from technical features of the process components. The approach is also strategic because the measured quality is determined against business-oriented component management goals. A software tool has been developed to measure how good a process component design is, according to the required managerial goals and comparing to other designs. We also discuss how we benefit from reusable process components.
Abstract: The effect of chemical treatment in CdCl2 and thermal
annealing in 400°C, on the defect structures of potentially useful
ZnS\CdS solar cell thin films deposited onto quartz substrate and
prepared by vacuum deposition method was studied using the
Thermoluminesence (TL) techniques. A series of electron and hole
traps are found in the various deposited samples studied. After
annealing, however, it was observed that the intensity and activation
energy of TL signal increases with loss of the low temperature
electron traps.
Abstract: The present study explains the effect of aggregate
gradation on moisture damage in bituminous mixes. Three types of
aggregate gradation and two types of binder; VG-30 and Polymer
modified bitumen (PMB-40) are used. Moisture susceptibility tests
like retained stability and tensile strength ratio (TSR) and static creep
test are conducted on Marshall specimens. The creep test was also
conducted for conditioned and unconditioned specimens to observe
the effect of moisture on creep behaviour. The results indicate that
Marshall stability value is higher in PMB-40 mix than VG-30 mixes.
Moisture susceptibility of PMB-40 mixes is low when compared with
mix using VG-30. The reduction in retained stability, and indirect
tensile strength and increase in creep are evaluated for finer, coarser
and normal gradation of aggregate to observe the effect of gradation
on moisture susceptibility of mixes. The retained stability is least
affected when compared with other moisture susceptibility
parameters
Abstract: Intelligent systems based on machine learning
techniques, such as classification, clustering, are gaining wide spread
popularity in real world applications. This paper presents work on
developing a software system for predicting crop yield, for example
oil-palm yield, from climate and plantation data. At the core of our
system is a method for unsupervised partitioning of data for finding
spatio-temporal patterns in climate data using kernel methods which
offer strength to deal with complex data. This work gets inspiration
from the notion that a non-linear data transformation into some high
dimensional feature space increases the possibility of linear
separability of the patterns in the transformed space. Therefore, it
simplifies exploration of the associated structure in the data. Kernel
methods implicitly perform a non-linear mapping of the input data
into a high dimensional feature space by replacing the inner products
with an appropriate positive definite function. In this paper we
present a robust weighted kernel k-means algorithm incorporating
spatial constraints for clustering the data. The proposed algorithm
can effectively handle noise, outliers and auto-correlation in the
spatial data, for effective and efficient data analysis by exploring
patterns and structures in the data, and thus can be used for
predicting oil-palm yield by analyzing various factors affecting the
yield.
Abstract: This paper presents the experimental results of
discharge current phenomena on various humidity, temperature,
pressure and pollutant conditions of epoxy resin specimen. The
leakage distance of specimen was 3 cm, that it was supplied by high
voltage. The polluted condition was given with NaCl artificial
pollutant. The conducted measurements were discharge current and
applied voltage. The specimen was put in a hermetically sealed
chamber, and the current waveforms were analyzed with FFT.
The result indicated that on discharge condition, the fifth
harmonics still had dominant, rather than third one. The third
harmonics tent to be appeared on low pressure heavily polluted
condition, and followed by high humidity heavily polluted condition.
On the heavily polluted specimen, the peaks discharge current points
would be high and more frequent. Nevertheless, the specimen still
had capacitive property. Besides that, usually discharge current
points were more frequent. The influence of low pressure was still
dominant to be easier to discharge. The non-linear property would be
appear explicitly on low pressure and heavily polluted condition.
Abstract: Chevron frames (Inverted-V-braced frames or Vbraced
frames) have seismic disadvantages, such as not good exhibit force redistribution capability and compression brace buckles
immediately. Researchers developed new design provisions on
increasing both the ductility and lateral resistance of these structures
in seismic areas. One of these new methods is adding zipper columns, as proposed by Khatib et al. (1988) [2]. Zipper columns are
vertical members connecting the intersection points of the braces
above the first floor. In this paper applicability of the suspended
zipper system to Seismic Rehabilitation of Steel Structures is investigated.
The models are 3-, 6-, 9-, and 12-story Inverted-V-braced frames.
In this case, it is assumed that the structures must be rehabilitated. For rehabilitation of structures, zipper column is used. The result of
researches showed that the suspended zipper system is effective in
case of 3-, 6-, and 9-story Inverted-V-braced frames and it would
increase lateral resistance of structure up to life safety level. But in
case of high-rise buildings (such as 12 story frame), it doesn-t show
good performance. For solving this problem, the braced bay can
consist of small “units" over the height of the entire structure, which each of them is a zipper-braced bay with a few stories. By using this
method the lateral resistance of 12 story Inverted-V-braced frames is increased up to safety life level.
Abstract: This article discusses the concept of student ownership of knowledge and seeks to determine how to move students from knowledge acquisition to knowledge application and ultimately to knowledge generation in a virtual setting. Instructional strategies for fostering student engagement in a virtual environment are critical to the learner-s strategic ownership of the knowledge. A number of relevant theories that focus on learning, affect, needs and adult concerns are presented to provide a basis for exploring the transfer of knowledge from teacher to learner. A model under development is presented that combines the dimensions of knowledge approach, the teacher-student relationship with regards to knowledge authority and teaching approach to demonstrate the recursive and scaffolded design for creation of virtual learning environments.
Abstract: The importance of inter-organizational system (IOS)
has been increasingly recognized by organizations. However, IOS
adoption has proved to be difficult and, at this stage, why this is so is
not fully uncovered. In practice, benefits have often remained
concentrated, primarily accruing to the dominant party, resulting in
low rates of adoption and usage, and often culminating in the failure
of the IOS. The main research question is why organizations initiate
or join IOS and what factors influence their adoption and use levels.
This paper reviews the literature on IOS adoption and proposes a
theoretical framework in order to identify the critical factors to
capture a complete picture of IOS adoption. With our proposed
critical factors, we are able to investigate their relative contributions
to IOS adoption decisions. We obtain findings that suggested that
there are five groups of factors that significantly affect the adoption
and use decision of IOS in the Supply Chain Management (SCM)
context: 1) interorganizational context, 2) organizational context, 3)
technological context, 4) perceived costs, and 5) perceived benefits.
Abstract: Temperature dependence of force of gravitation is one
of the fundamental problems of physics. This problem has got special
value in connection with that the general theory of relativity,
supposing the weakest positive influence of a body temperature on its
weight, actually rejects an opportunity of measurement of negative
influence of temperature on gravity in laboratory conditions. Really,
the recognition of negative temperature dependence of gravitation,
for example, means basic impossibility of achievement of a
singularity («a black hole») at a gravitational collapse. Laboratory
experiments with exact weighing the heated up metal samples,
indicating negative influence temperatures of bodies on their physical
weight are described. Influence of mistakes of measurements is
analyzed. Calculations of distribution of temperature in volume of the
bar, agreed with experimental data of time dependence of weight of
samples are executed. The physical substantiation of negative
temperature dependence of weight of the bodies, based on correlation
of acceleration at thermal movement of micro-particles of a body and
its absolute temperature, are given.
Abstract: This article stands in the context of rural communities
in Brazil, where, like many others emerging countries, the
overwhelming increasing markets and the overcrowded cities are
leaving behind informal settlements based on obsolete agricultural
economies and techniques. The pilot project for the community of
Goiabeira reflects the attempt to imagine a development model that
privileges the actual improvement of living conditions, the education
and training, the social inclusion and participation of the dwellers of
rural communities. Through the inclusion of operative public space,
the aim is for them to become self-sustaining, encouraging the use of
local resources for appropriate architectural, ecological and energy
technologies and devices, that are efficient, affordable and foster
community participation, in the respect of the surrounding
environment.
Abstract: With the growth of electricity generation from gas
energy gas pipeline reliability can substantially impact the electric
generation. A physical disruption to pipeline or to a compressor
station can interrupt the flow of gas or reduce the pressure and lead
to loss of multiple gas-fired electric generators, which could
dramatically reduce the supplied power and threaten the power
system security. Gas pressure drops during peak loading time on
pipeline system, is a common problem in network with no enough
transportation capacity which limits gas transportation and causes
many problem for thermal domain power systems in supplying their
demand. For a feasible generation scheduling planning in networks
with no sufficient gas transportation capacity, it is required to
consider gas pipeline constraints in solving the optimization problem
and evaluate the impacts of gas consumption in power plants on gas
pipelines operating condition. This paper studies about operating of
gas fired power plants in critical conditions when the demand of gas
and electricity peak together. An integrated model of gas and electric
model is used to consider the gas pipeline constraints in the economic
dispatch problem of gas-fueled thermal generator units.
Abstract: The recent developments in computing and
communication technology permit to users to access multimedia
documents with variety of devices (PCs, PDAs, mobile phones...)
having heterogeneous capabilities. This diversification of supports
has trained the need to adapt multimedia documents according to
their execution contexts. A semantic framework for multimedia
document adaptation based on the conceptual neighborhood graphs
was proposed. In this framework, adapting consists on finding
another specification that satisfies the target constraints and which is
as close as possible from the initial document. In this paper, we
propose a new way of building the conceptual neighborhood graphs
to best preserve the proximity between the adapted and the original
documents and to deal with more elaborated relations models by
integrating the relations relaxation graphs that permit to handle the
delays and the distances defined within the relations.
Abstract: This research proposes a methodology for patent-citation-based technology input-output analysis by applying the patent information to input-output analysis developed for the dependencies among different industries. For this analysis, a technology relationship matrix and its components, as well as input and technology inducement coefficients, are constructed using patent information. Then, a technology inducement coefficient is calculated by normalizing the degree of citation from certain IPCs to the different IPCs (International patent classification) or to the same IPCs. Finally, we construct a Dependency Structure Matrix (DSM) based on the technology inducement coefficient to suggest a useful application for this methodology.
Abstract: A Data Warehouses is a repository of information
integrated from source data. Information stored in data warehouse is
the form of materialized in order to provide the better performance
for answering the queries. Deciding which appropriated views to be
materialized is one of important problem. In order to achieve this
requirement, the constructing search space close to optimal is a
necessary task. It will provide effective result for selecting view to be
materialized. In this paper we have proposed an approach to reoptimize
Multiple View Processing Plan (MVPP) by using global
common subexpressions. The merged queries which have query
processing cost not close to optimal would be rewritten. The
experiment shows that our approach can help to improve the total
query processing cost of MVPP and sum of query processing cost
and materialized view maintenance cost is reduced as well after views
are selected to be materialized.
Abstract: In this paper, an Interactive Compromise Approach
with Particle Swarm Optimization(ICA-PSO) is presented to solve the
Economic Emission Dispatch(EED) problem. The cost function and
emission function are modeled as the nonsmooth functions,
respectively. The bi-objective including both the minimization of cost
and emission is formulated in this paper. ICA-PSO is proposed to
solve EED problem for finding a better compromise solution. The
solution methodology can offer a global or near-global solution for
decision-making requirements. The effectiveness and efficiency of
ICA-PSO are demonstrated by a sample test system. Test results can
be shown that the proposed method provide a practical and flexible
framework for power dispatch.