Abstract: A high-frequency low-power sinusoidal quadrature
oscillator is presented through the use of two 2nd-order low-pass
current-mirror (CM)-based filters, a 1st-order CM low-pass filter and
a CM bilinear transfer function. The technique is relatively simple
based on (i) inherent time constants of current mirrors, i.e. the
internal capacitances and the transconductance of a diode-connected
NMOS, (ii) a simple negative resistance RN formed by a resistor load
RL of a current mirror. Neither external capacitances nor inductances
are required. As a particular example, a 1.9-GHz, 0.45-mW, 2-V
CMOS low-pass-filter-based all-current-mirror sinusoidal quadrature
oscillator is demonstrated. The oscillation frequency (f0) is 1.9 GHz
and is current-tunable over a range of 370 MHz or 21.6 %. The
power consumption is at approximately 0.45 mW. The amplitude
matching and the quadrature phase matching are better than 0.05 dB
and 0.15°, respectively. Total harmonic distortions (THD) are less
than 0.3 %. At 2 MHz offset from the 1.9 GHz, the carrier to noise
ratio (CNR) is 90.01 dBc/Hz whilst the figure of merit called a
normalized carrier-to-noise ratio (CNRnorm) is 153.03 dBc/Hz. The
ratio of the oscillation frequency (f0) to the unity-gain frequency (fT)
of a transistor is 0.25. Comparisons to other approaches are also
included.
Abstract: A five-class density histogram with an index named cumulative density was proposed to analyze the short-term HRV. 150 subjects participated in the test, falling into three groups with equal numbers -- the healthy young group (Young), the healthy old group (Old), and the group of patients with congestive heart failure (CHF). Results of multiple comparisons showed a significant differences of the cumulative density in the three groups, with values 0.0238 for Young, 0.0406 for Old and 0.0732 for CHF (p
Abstract: In this paper a neural adaptive control method has
been developed and applied to robot control. Simulation results are
presented to verify the effectiveness of the controller. These results
show that the performance by using this controller is better than
those which just use either direct inverse control or predictive
control. In addition, they show that the resulting is a useful method
which combines the advantages of both direct inverse control and
predictive control.
Abstract: The paper considered the construction of BIBDs using potential Lotto Designs (LDs) earlier derived from qualifying parent BIBDs. The study utilized Li’s condition pr t−1 ( t−1 2 ) + pr− pr t−1 (t−1) 2 < ( p 2 ) λ, to determine the qualification of a parent BIBD (v, b, r, k, λ) as LD (n, k, p, t) constrained on v ≥ k, v ≥ p, t ≤ min{k, p} and then considered the case k = t since t is the smallest number of tickets that can guarantee a win in a lottery. The (15, 140, 28, 3, 4) and (7, 7, 3, 3, 1) BIBDs were selected as parent BIBDs to illustrate the procedure. These BIBDs yielded three potential LDs each. Each of the LDs was completely generated and their properties studied. The three LDs from the (15, 140, 28, 3, 4) produced (9, 84, 28, 3, 7), (10, 120, 36, 3, 8) and (11, 165, 45, 3, 9) BIBDs while those from the (7, 7, 3, 3, 1) produced the (5, 10, 6, 3, 3), (6, 20, 10, 3, 4) and (7, 35, 15, 3, 5) BIBDs. The produced BIBDs follow the generalization (v + 1, b + r + λ + 1, r +λ+1, k, λ+1) where (v, b, r, k, λ) are the parameters of the (9, 84, 28, 3, 7) and (5, 10, 6, 3, 3) BIBDs. All the BIBDs produced are unreduced designs.
Abstract: The emergence of mobile application services and App
Store has led to the explosive growth of user innovation, which users
voluntarily contribute to. User innovation communities where end
users freely reveal innovative ideas and needs with other community
members are becoming increasingly influential in this area. However,
user-s ideas in user innovation community are not enough to be new
service opportunity, because some of them can already developed as
existing services in App Store. Moreover, the existing services similar
to new service opportunity can be significant references to apply
analogy to develop service concept. In response, this research
proposes Case-Based Reasoning approach to matching the user needs
and existing services, identifying unmet opportunistic user needs, and
retrieving similar services with opportunity. Due to its intuitive and
transparent algorithm, users related to App Store innovation
communities can easily employ Case-Based Reasoning based
approach to their innovation.
Abstract: Background: This investigated the mental health of the elderly survivors six months, ten months and two years after the “5.12 Wenchuan" earthquake. Methods: Two hundred and thirty-two physically healthy older survivors from earthquake-affected Mianyang County were interviewed. The measures included the Revised Impact of Event Scale (IES-R, Chinese version, for PTSD) and a Chinese Mental Health Inventory for the Elderly (MHIE). A repeated measures ANOVA test was used for statistical analysis. Results: The follow-up group had a statistically significant lower IES-R score and lower MHIE score than the initial group ten months after the earthquake. Two years later, the score of IES-R in follow-up group were still lower than that of non-follow-up group, but no differences were significant on the score of MHIE between groups. Furthermore, a negative relationship was found between scores of IES-R and MHIE. Conclusion: The earthquake has had a persistent negative impact on older survivors- mental health within the two-year period and that although the PTSD level declined significantly with time, it did not disappear completely.
Abstract: By employing BS (Base Station) cooperation we can
increase substantially the spectral efficiency and capacity of cellular
systems. The signals received at each BS are sent to a central unit that
performs the separation of the different MT (Mobile Terminal) using
the same physical channel. However, we need accurate sampling and
quantization of those signals so as to reduce the backhaul
communication requirements.
In this paper we consider the optimization of the quantizers for BS
cooperation systems. Four different quantizer types are analyzed and
optimized to allow better SQNR (Signal-to-Quantization Noise
Ratio) and BER (Bit Error Rate) performance.
Abstract: An empirical study of web applications that use
software frameworks is presented here. The analysis is based on two
approaches. In the first, developers using such frameworks are
required, based on their experience, to assign weights to parameters
such as database connection. In the second approach, a performance
testing tool, OpenSTA, is used to compute start time and other such
measures. From such an analysis, it is concluded that open source
software is superior to proprietary software. The motivation behind
this research is to examine ways in which a quantitative assessment
can be made of software in general and frameworks in particular.
Concepts such as metrics and architectural styles are discussed along
with previously published research.
Abstract: The hand is one of the essential parts of the body for
carrying out Activities of Daily Living (ADLs). Individuals use their
hands and fingers in everyday activities in the both the workplace
and home. Hand-intensive tasks require diverse and sometimes
extreme levels of exertion, depending on the action, movement or
manipulation involved. The authors have undertaken several studies
looking at grip choice and comfort. It is hoped that in providing
improved understanding of discomfort during ADLs this will aid in
the design of consumer products.
Previous work by the authors outlined a methodology for
calculating pain frequency and pain level for a range of tasks. From
an online survey undertaken by the authors with regards
manipulating objects during everyday tasks, tasks involving
gripping were seen to produce the highest levels of pain and
discomfort. Questioning of the participants showed that cleaning
tasks were seen to be ADL's that produced the highest levels of
discomfort, with women feeling higher levels of discomfort than
men.
This paper looks at the methodology for calculating pain
frequency and pain level with particular regards to gripping
activities. This methodology shows that activities such as mopping,
sweeping and hoovering shows the highest numbers of pain
frequency and pain level at 3112.5 frequency per month while the
pain level per person doing this action was 0.78.The study then uses
thin-film force sensors to analyze the force distribution in the hand
whilst hoovering and compares this for differing grip styles and
genders. Women were seen to have more of their hand under a
higher pressure than men when undertaking hoovering. This
suggests that women may feel greater discomfort than men since
their hand is at a higher pressure more of the time.
Abstract: The most important parameter in transformers life
expectancy is the hot-spot temperature level which accelerates the
rate of aging of the insulation. The aim of this paper is to present
thermal models for transformers loaded at prefabricated MV/LV
transformer substations and outdoor situations. The hot-spot
temperature of transformers is studied using their top-oil temperature
rise models. The thermal models proposed for hot-spot and top-oil
temperatures of different operating situations are compared. Since the
thermal transfer is different for indoor and outdoor transformers
considering their operating conditions, their hot-spot thermal models
differ from each other. The proposed thermal models are verified by
the results obtained from the experiments carried out on a typical
1600 kVA, 30 /0.4 kV, ONAN transformer for both indoor and
outdoor situations.
Abstract: This paper presents a new method of analog fault diagnosis based on back-propagation neural networks (BPNNs) using wavelet decomposition and fractal dimension as preprocessors. The proposed method has the capability to detect and identify faulty components in an analog electronic circuit with tolerance by analyzing its impulse response. Using wavelet decomposition to preprocess the impulse response drastically de-noises the inputs to the neural network. The second preprocessing by fractal dimension can extract unique features, which are the fed to a neural network as inputs for further classification. A comparison of our work with [1] and [6], which also employs back-propagation (BP) neural networks, reveals that our system requires a much smaller network and performs significantly better in fault diagnosis of analog circuits due to our proposed preprocessing techniques.
Abstract: Subsurface erosion in river banks and its details, in
spite of its occurrence in various parts of the world has rarely been
paid attention by researchers. In this paper, quantitative concept of
the subsurface bank erosion has been investigated for vertical banks.
Vertical banks were simulated experimentally by considering a sandy
erodible layer overlaid by clayey one under uniformly distributed
constant overhead pressure. Results of the experiments are indicated
that rate of sandy layer erosion is decreased by an increase in
overburden; likewise, substituting 20% of coarse (3.5 mm) sand layer
bed material by fine material (1.4 mm) may lead to a decrease in
erosion rate by one-third. This signifies the importance of the bed
material composition effect on sandy layers erosion due to subsurface
erosion in river banks.
Abstract: Some meta-schedulers query the information system of individual supercomputers in order to submit jobs to the least busy supercomputer on a computational Grid. However, this information can become outdated by the time a job starts due to changes in scheduling priorities. The MSR scheme is based on Multiple Simultaneous Requests and can take advantage of opportunities resulting from these priorities changes. This paper presents the SWARM meta-scheduler, which can speed up the execution of large sets of tasks by minimizing the job queuing time through the submission of multiple requests. Performance tests have shown that this new meta-scheduler is faster than an implementation of the MSR scheme and the gLite meta-scheduler. SWARM has been used through the GridQTL project beta-testing portal during the past year. Statistics are provided for this usage and demonstrate its capacity to achieve reliably a substantial reduction of the execution time in production conditions.
Abstract: Reciprocating compressors are flexible to handle wide capacity and condition swings, offer a very efficient method of compressing almost any gas mixture in wide range of pressure, can generate high head independent of density, and have numerous applications and wide power ratings. These make them vital component in various units of industrial plants. In this paper optimum reciprocating compressor configuration regarding interstage pressures, low suction pressure, non-lubricated cylinder, speed of machine, capacity control system, compressor valve, lubrication system, piston rod coating, cylinder liner material, barring device, pressure drops, rod load, pin reversal, discharge temperature, cylinder coolant system, performance, flow, coupling, special tools, condition monitoring (including vibration, thermal and rod drop monitoring), commercial points, delivery and acoustic conditions are presented.
Abstract: Computers are being integrated in the various aspects
of human every day life in different shapes and abilities. This fact
has intensified a requirement for the software development
technologies which is ability to be: 1) portable, 2) adaptable, and 3)
simple to develop. This problem is also known as the Pervasive
Computing Problem (PCP) which can be implemented in different
ways, each has its own pros and cons and Context Oriented
Programming (COP) is one of the methods to address the PCP.
In this paper a design for a COP framework, a context aware
framework, is presented which has eliminated weak points of a
previous design based on interpreter languages, while introducing the
compiler languages power in implementing these frameworks.
The key point of this improvement is combining COP and
Dependency Injection (DI) techniques. Both old and new frameworks
are analyzed to show advantages and disadvantages. Finally a
simulation of both designs is proposed to indicating that the practical
results agree with the theoretical analysis while the new design runs
almost 8 times faster.
Abstract: Since the world printing industry has to confront
globalization with a constant change, the Thai printing industry, as a
small but increasingly significant part of the world printing industry,
cannot inevitably escape but has to encounter with the similar change
and also the need to revamp its production processes, designs and
technology to make them more appealing to both international and
domestic market. The essential question is what is the Thai
competitive edge in the printing industry in changing environment?
This research is aimed to study the Thai level of competitive edge in
terms of marketing, technology, environment friendly, and the level
of satisfaction of the process of using printing machines. To access
the extent to which is the trends in competitiveness of Thai printing
industry, both quantitative and qualitative study were conducted. The
quantitative analysis was restricted to 100 respondents. The
qualitative analysis was restricted to a focus group of 10 individuals
from various backgrounds in the Thai printing industry. The findings
from the quantitative analysis revealed that the overall mean scores
are 4.53, 4.10, and 3.50 for the competitiveness of marketing, the
competitiveness of technology, and the competitiveness of being
environment friendly respectively. However, the level of satisfaction
for the process of using machines has a mean score only 3.20. The
findings from the qualitative analysis have revealed that target
customers have increasingly reordered due to their contentment in
both low prices and the acceptable quality of the products. Moreover,
the Thai printing industry has a tendency to convert to ambient green
technology which is friendly to the environment. The Thai printing
industry is choosing to produce or substitute with products that are
less damaging to the environment. It is also found that the Thai
printing industry has been transformed into a very competitive
industry which bargaining power rests on consumers who have a
variety of choices.
Abstract: Groups where the discrete logarithm problem (DLP) is believed to be intractable have proved to be inestimable building blocks for cryptographic applications. They are at the heart of numerous protocols such as key agreements, public-key cryptosystems, digital signatures, identification schemes, publicly verifiable secret sharings, hash functions and bit commitments. The search for new groups with intractable DLP is therefore of great importance.The goal of this article is to study elliptic curves over the ring Fq[], with Fq a finite field of order q and with the relation n = 0, n ≥ 3. The motivation for this work came from the observation that several practical discrete logarithm-based cryptosystems, such as ElGamal, the Elliptic Curve Cryptosystems . In a first time, we describe these curves defined over a ring. Then, we study the algorithmic properties by proposing effective implementations for representing the elements and the group law. In anther article we study their cryptographic properties, an attack of the elliptic discrete logarithm problem, a new cryptosystem over these curves.
Abstract: The aim of this study is to determine the effect of
strategic management implementations on the institutionalization
levels. In this regard a field study has been made over 31 stone quarry
enterprises in cement producing sector in Konya by using survey
method. In this study, institutionalization levels of the enterprises
have been evaluated regarding three dimensions: professionalization,
management approach, participation in decisions and delegation of
authority. According to the results of the survey, there is a highly
positive and statistically significant relationship between the strategic
management implementations and institutionalization levels of the
enterprises. Additionally,-considering the results of regression
analysis made for establishing the relationship between strategic
management and institutionalization levels- it has been determined
that strategic management implementations of the enterprises can be
used as a variable to explain the institutionalization levels of them,
and also strategic management implementations of the enterprises
increase the institutionalization levels of them.
Abstract: The least mean square (LMS) algorithmis one of the
most well-known algorithms for mobile communication systems
due to its implementation simplicity. However, the main limitation
is its relatively slow convergence rate. In this paper, a booster
using the concept of Markov chains is proposed to speed up the
convergence rate of LMS algorithms. The nature of Markov
chains makes it possible to exploit the past information in the
updating process. Moreover, since the transition matrix has a
smaller variance than that of the weight itself by the central limit
theorem, the weight transition matrix converges faster than the
weight itself. Accordingly, the proposed Markov-chain based
booster thus has the ability to track variations in signal
characteristics, and meanwhile, it can accelerate the rate of
convergence for LMS algorithms. Simulation results show that the
LMS algorithm can effectively increase the convergence rate and
meantime further approach the Wiener solution, if the
Markov-chain based booster is applied. The mean square error is
also remarkably reduced, while the convergence rate is improved.
Abstract: In the classical buckling analysis of rectangular plates
subjected to the concurrent action of shear and uniaxial forces, the
Euler shear buckling stress is generally evaluated separately, so that
no influence on the shear buckling coefficient, due to the in-plane
tensile or compressive forces, is taken into account.
In this paper the buckling problem of simply supported rectangular
plates, under the combined action of shear and uniaxial forces, is
discussed from the beginning, in order to obtain new project formulas
for the shear buckling coefficient that take into account the presence
of uniaxial forces.
Furthermore, as the classical expression of the shear buckling
coefficient for simply supported rectangular plates is considered only
a “rough" approximation, as the exact one is defined by a system of
intersecting curves, the convergence and the goodness of the classical
solution are analyzed, too.
Finally, as the problem of the Euler shear buckling stress
evaluation is a very important topic for a variety of structures, (e.g.
ship ones), two numerical applications are carried out, in order to
highlight the role of the uniaxial stresses on the plating scantling
procedures and the goodness of the proposed formulas.