Abstract: In recent years, rehabilitation has been the subject of extensive research due to increased spending on building work and repair of built works. In all cases, it is absolutely essential to carry out methods of strengthening or repair of structural elements, and that following an inspection analysis and methodology of a correct diagnosis. The reinforced concrete columns are important elements in building structures. They support the vertical loads and provide bracing against the horizontal loads. This research about the behavior of reinforced concrete rectangular columns, rehabilitated by concrete liner, confinement FRP fabric, steel liner or cage formed by metal corners. It allows comparing the contributions of different processes used perspective section resistance elements rehabilitated compared to that is not reinforced or repaired. The different results obtained revealed a considerable gain in bearing capacity failure of reinforced sections cladding concrete, metal bracket, steel plates and a slight improvement to the section reinforced with fabric FRP. The use of FRP does not affect the weight of the structures, but the use of different techniques cladding increases the weight of elements rehabilitated and therefore the weight of the building which requires resizing foundations.
Abstract: This paper presents the approximate analytical solution of a Zakharov-Kuznetsov ZK(m, n, k) equation with the help of the differential transform method (DTM). The DTM method is a powerful and efficient technique for finding solutions of nonlinear equations without the need of a linearization process. In this approach the solution is found in the form of a rapidly convergent series with easily computed components. The two special cases, ZK(2,2,2) and ZK(3,3,3), are chosen to illustrate the concrete scheme of the DTM method in ZK(m, n, k) equations. The results demonstrate reliability and efficiency of the proposed method.
Abstract: Sleep spindles are the most interesting hallmark of
stage 2 sleep EEG. Their accurate identification in a
polysomnographic signal is essential for sleep professionals to help
them mark Stage 2 sleep. Sleep Spindles are also promising objective
indicators for neurodegenerative disorders. Visual spindle scoring
however is a tedious workload. In this paper three different
approaches are used for the automatic detection of sleep spindles:
Short Time Fourier Transform, Wavelet Transform and Wave
Morphology for Spindle Detection. In order to improve the results, a
combination of the three detectors is presented and comparison with
human expert scorers is performed. The best performance is obtained
with a combination of the three algorithms which resulted in a
sensitivity and specificity of 94% when compared to human expert
scorers.
Abstract: In DMVC, we have more than one options of sources available for construction of side information. The newer techniques make use of both the techniques simultaneously by constructing a bitmask that determines the source of every block or pixel of the side information. A lot of computation is done to determine each bit in the bitmask. In this paper, we have tried to define areas that can only be well predicted by temporal interpolation and not by multiview interpolation or synthesis. We predict that all such areas that are not covered by two cameras cannot be appropriately predicted by multiview synthesis and if we can identify such areas in the first place, we don-t need to go through the script of computations for all the pixels that lie in those areas. Moreover, this paper also defines a technique based on KLT to mark the above mentioned areas before any other processing is done on the side view.
Abstract: Thirty three re-wetting tests were conducted at
different combinations of temperatures (5.7- 46.30C) and relative
humidites (48.2-88.6%) with barley. Two most commonly used thinlayer
drying and rewetting models i.e. Page and Diffusion were
compared for their ability to the fit the experimental re-wetting data
based on the standard error of estimate (SEE) of the measured and
simulated moisture contents. The comparison shows both the Page
and Diffusion models fit the re-wetting experimental data of barley
well. The average SEE values for the Page and Diffusion models
were 0.176 % d.b. and 0.199 % d.b., respectively. The Page and
Diffusion models were found to be most suitable equations, to
describe the thin-layer re-wetting characteristics of barley over a
typically five day re-wetting. These two models can be used for the
simulation of deep-bed re-wetting of barley occurring during
ventilated storage and deep bed drying.
Abstract: A subsea hydrocarbon production system can undergo planned and unplanned shutdowns during the life of the field. The thermal FEA is used to simulate the cool down to verify the insulation design of the subsea equipment, but it is also used to derive an acceptable insulation design for the cold spots. The driving factors of subsea analyses require fast responding and accurate models of the equipment cool down. This paper presents cool down analysis carried out by a Krylov subspace reduction method, and compares this approach to the commonly used FEA solvers. The model considered represents a typical component of a subsea production system, a closed valve on a dead leg. The results from the Krylov reduction method exhibits the least error and requires the shortest computational time to reach the solution. These findings make the Krylov model order reduction method very suitable for the above mentioned subsea applications.
Abstract: Recently, Genetic Algorithms (GA) and Differential
Evolution (DE) algorithm technique have attracted considerable
attention among various modern heuristic optimization techniques.
Since the two approaches are supposed to find a solution to a given
objective function but employ different strategies and computational
effort, it is appropriate to compare their performance. This paper
presents the application and performance comparison of DE and GA
optimization techniques, for flexible ac transmission system
(FACTS)-based controller design. The design objective is to enhance
the power system stability. The design problem of the FACTS-based
controller is formulated as an optimization problem and both the PSO
and GA optimization techniques are employed to search for optimal
controller parameters. The performance of both optimization
techniques has been compared. Further, the optimized controllers are
tested on a weekly connected power system subjected to different
disturbances, and their performance is compared with the
conventional power system stabilizer (CPSS). The eigenvalue
analysis and non-linear simulation results are presented and
compared to show the effectiveness of both the techniques in
designing a FACTS-based controller, to enhance power system
stability.
Abstract: As the development of digital technology is increasing,
Digital cinema is getting more spread.
However, content copy and attack against the digital cinema becomes
a serious problem. To solve the above security problem, we propose
“Additional Watermarking" for digital cinema delivery system. With
this proposed “Additional watermarking" method, we protect content
copyrights at encoder and user side information at decoder. It realizes
the traceability of the watermark embedded at encoder.
The watermark is embedded into the random-selected frames using
Hash function. Using it, the embedding position is distributed by Hash
Function so that third parties do not break off the watermarking
algorithm.
Finally, our experimental results show that proposed method is much
better than the convenient watermarking techniques in terms of
robustness, image quality and its simple but unbreakable algorithm.
Abstract: After the accounting scandals and the financial crisis, regulators have stressed the need for more financial experts on boards. Several studies conducted in countries with developed capital markets report positive effects of board financial competencies. As each country offers a different context and specific institutional factors this paper addresses the subject in the context of Romania. The Romanian capital market offers an interesting research field because of the heterogeneity of listed firms. After analyzing board members education based on public information posted on listed companies websites and their annual reports we found a positive association between the proportion of board members holding a postgraduate degree in financial fields and market based performance measured by Tobin q. We found also that the proportion of Board members holding degrees in financial fields is higher in bigger firms and firms with more concentrated ownership.
Abstract: The H.264/AVC standard uses an intra prediction, 9
directional modes for 4x4 luma blocks and 8x8 luma blocks, 4
directional modes for 16x16 macroblock and 8x8 chroma blocks,
respectively. It means that, for a macroblock, it has to perform 736
different RDO calculation before a best RDO modes is determined.
With this Multiple intra-mode prediction, intra coding of H.264/AVC
offers a considerably higher improvement in coding efficiency
compared to other compression standards, but computational
complexity is increased significantly. This paper presents a fast intra
prediction algorithm for H.264/AVC intra prediction based a
characteristic of homogeneity information. In this study, the gradient
prediction method used to predict the homogeneous area and the
quadratic prediction function used to predict the nonhomogeneous
area. Based on the correlation between the homogeneity and block
size, the smaller block is predicted by gradient prediction and
quadratic prediction, so the bigger block is predicted by gradient
prediction. Experimental results are presented to show that the
proposed method reduce the complexity by up to 76.07%
maintaining the similar PSNR quality with about 1.94%bit rate
increase in average.
Abstract: Removal of PCP by a system combining
biodegradation by biofilm and adsorption was investigated here.
Three studies were conducted employing batch tests, sequencing
batch reactor (SBR) and continuous biofilm activated carbon
column reactor (BACCOR). The combination of biofilm-GAC
batch process removed about 30% more PCP than GAC adsorption
alone. For the SBR processes, both the suspended and attached
biomass could remove more than 90% of the PCP after
acclimatisation. BACCOR was able to remove more than 98% of
PCP-Na at concentrations ranging from 10 to 100 mg/L, at empty
bed contact time (EBCT) ranging from 0.75 to 4 hours. Pure and
mixed cultures from BACCOR were tested for use of PCP as sole
carbon and energy source under aerobic conditions. The isolates
were able to degrade up to 42% of PCP under aerobic conditions in
pure cultures. However, mixed cultures were found able to degrade
more than 99% PCP indicating interdependence of species.
Abstract: Environmental performance of the U.S. States is investigated for the period of 1990 – 2007 using Stochastic Frontier Analysis (SFA). The SFA accounts for both efficiency measure and stochastic noise affecting a frontier. The frontier is formed using indicators of GDP, energy consumption, population, and CO2 emissions. For comparability, all indicators are expressed as ratios to total. Statistical information of the Energy Information Agency of the United States is used. Obtained results reveal the bell - shaped dynamics of environmental efficiency scores. The average efficiency scores rise from 97.6% in 1990 to 99.6% in 1999, and then fall to 98.4% in 2007. The main factor is insufficient decrease in the rate of growth of CO2 emissions with regards to the growth of GDP, population and energy consumption. Data for 2008 following the research period allow for an assumption that the environmental performance of the U.S. States has improved in the last years.
Abstract: This paper outlines the research conducted to propose na framework of 'Knowledge Society' (KS) in the Malaysian context.
It is important to highlight that the emergence of KS is a result of the rapid growth in knowledge and information. However, the discussion
of KS should not only be limited to the importance of knowledge, but a holistic KS is also determined by other imperative dimensions. This
article discusses the results of a study conducted previously in Malaysia in order to identify the essential dimensions of KS, and
consequently propose a KS framework in the Malaysian context.
Two methods were employed, namely the Delphi technique and semi-structured interviews. The modified Delphi involved five
rounds with ten experts, while the interviews were conducted with two prominent figures in Malaysia. The results support the proposed
framework which contains seven major dimensions in order for Malaysia to become a KS in the future. The dimensions which are
crucial for a holistic Malaysian KS are human capital, spirituality, economy, social, institutional, sustainability, and driven by the ICT.
Abstract: In this paper, an analysis is presented, which
demonstrates the effect pre-logic factoring could have on an
automated combinational logic synthesis process succeeding it. The
impact of pre-logic factoring for some arbitrary combinatorial
circuits synthesized within a FPGA based logic design environment
has been analyzed previously. This paper explores a similar effect,
but with the non-regenerative logic synthesized using elements of a
commercial standard cell library. On an overall basis, the results
obtained pertaining to the analysis on a variety of MCNC/IWLS
combinational logic benchmark circuits indicate that pre-logic
factoring has the potential to facilitate simultaneous power, delay and
area optimized synthesis solutions in many cases.
Abstract: This study reports the preparation of soft magnetic ribbons of Fe-based amorphous alloys using the single-roller melt-spinning technique. Ribbon width varied from 142 mm to 213 mm and, with a thickness of approximately 22 μm 2 μm. The microstructure and magnetic properties of the ribbons were characterized by differential scanning calorimeter (DSC), X-ray diffraction (XRD), vibrating sample magnetometer (VSM), and electrical resistivity measurements (ERM). The amorphous material properties dependence of the cooling rate and nozzle pressure have uneven surface in ribbon thicknesses are investigated. Magnetic measurement results indicate that some region of the ribbon exhibits good magnetic properties, higher saturation induction and lower coercivity. However, due to the uneven surface of 213 mm wide ribbon, the magnetic responses are not uniformly distributed. To understand the transformer magnetic performances, this study analyzes the measurements of a three-phase 2 MVA amorphous-cored transformer. Experimental results confirm that the transformer with a ribbon width of 142 mm has better magnetic properties in terms of lower core loss, exciting power, and audible noise.
Abstract: METIS is the Multi Element Telescope for Imaging
and Spectroscopy, a Coronagraph aboard the European Space
Agency-s Solar Orbiter Mission aimed at the observation of the solar
corona via both VIS and UV/EUV narrow-band imaging and spectroscopy. METIS, with its multi-wavelength capabilities, will
study in detail the physical processes responsible for the corona heating and the origin and properties of the slow and fast solar wind.
METIS electronics will collect and process scientific data thanks to its detectors proximity electronics, the digital front-end subsystem
electronics and the MPPU, the Main Power and Processing Unit,
hosting a space-qualified processor, memories and some rad-hard
FPGAs acting as digital controllers.This paper reports on the overall
METIS electronics architecture and data processing capabilities
conceived to address all the scientific issues as a trade-off solution between requirements and allocated resources, just before the
Preliminary Design Review as an ESA milestone in April 2012.
Abstract: Energy intensity(energy consumption intensity) is a
global index which computes the required energy for producing a
specific value of goods and services in each country. It is computed
in terms of initial energy supply or final energy consumption. In this
study (research) Divisia method is used to decompose energy
consumption and energy intensity. This method decomposes
consumption and energy intensity to production effects, structural
and net intensity and could be done as time series or two-periodical.
This study analytically investigates consumption changes and energy
intensity on economical sectors of Iran and more specific on road
transportation(rail road and road).Our results show that the
contribution of structural effect (change in economical activities
combination) is very low and the effect of net energy consumption
has the higher contribution in consumption changes and energy
intensity. In other words, the high consumption of energy is due to
Intensity of energy consumption and is not to structural effect of
transportation sector.
Abstract: Local Linear Neuro-Fuzzy Models (LLNFM) like other neuro- fuzzy systems are adaptive networks and provide robust learning capabilities and are widely utilized in various applications such as pattern recognition, system identification, image processing and prediction. Local linear model tree (LOLIMOT) is a type of Takagi-Sugeno-Kang neuro fuzzy algorithm which has proven its efficiency compared with other neuro fuzzy networks in learning the nonlinear systems and pattern recognition. In this paper, a dedicated reconfigurable and parallel processing hardware for LOLIMOT algorithm and its applications are presented. This hardware realizes on-chip learning which gives it the capability to work as a standalone device in a system. The synthesis results on FPGA platforms show its potential to improve the speed at least 250 of times faster than software implemented algorithms.
Abstract: The empirical mode decomposition (EMD) represents any time series into a finite set of basis functions. The bases are termed as intrinsic mode functions (IMFs) which are mutually orthogonal containing minimum amount of cross-information. The EMD successively extracts the IMFs with the highest local frequencies in a recursive way, which yields effectively a set low-pass filters based entirely on the properties exhibited by the data. In this paper, EMD is applied to explore the properties of the multi-year air temperature and to observe its effects on climate change under global warming. This method decomposes the original time-series into intrinsic time scale. It is capable of analyzing nonlinear, non-stationary climatic time series that cause problems to many linear statistical methods and their users. The analysis results show that the mode of EMD presents seasonal variability. The most of the IMFs have normal distribution and the energy density distribution of the IMFs satisfies Chi-square distribution. The IMFs are more effective in isolating physical processes of various time-scales and also statistically significant. The analysis results also show that the EMD method provides a good job to find many characteristics on inter annual climate. The results suggest that climate fluctuations of every single element such as temperature are the results of variations in the global atmospheric circulation.
Abstract: This is an applied research to propose the method for
price quotation for a contract electronics manufacturer. It has had a
precise price quoting method but such method could not quickly
provide a result as the customer required. This reduces the ability of
company to compete in this kind of business. In this case, the cause
of long time quotation process was analyzed. A lot of product
features have been demanded by customer. By checking routine
processes, it was found that high fraction of quoting time was used
for production time estimating which has effected to the
manufacturing or production cost. Then the historical data of
products including types, number of components, assembling
method, and their assembling time were used to analyze the key
components affecting to production time. The price quoting model
then was proposed. The implementation of proposed model was able
to remarkably reduce quoting time with an acceptable required
precision.