Abstract: The main purpose of this study is to provide a detailed
statistical overview of the time and regional distribution, relative
timing occurrence of economic crises and government changes in 51
economies over the 1990–2007 periods. At the same time, the
predictive power of the economic crises on set government changes
will be examined using “signal approach".
The result showed that the percentage of government changes is
highest in transition economies (86 percent of observations) and
lowest in Latin American economies (39 percent of observations).
The percentages of government changes are same in both developed
and developing countries (43 percent of observations). However,
average crises per year (frequency of crises) are higher (lower) in
developing (developed) countries than developed (developing)
countries. Also, the predictive power of economic crises about the
onset of a government change is highest in Transition economies (81
percent) and lowest in Latin American countries (30 percent). The
predictive power of economic crises in developing countries (43
percent) is lower than developed countries (55 percent).
Abstract: This paper proposes the application of a hierarchical fuzzy system (HFS) based on multi-input power system stabilizer (MPSS) and also Static Var Compensator (SVC) in multi-machine environment.The number of rules grows exponentially with the number of variables in a conventional fuzzy logic system. The proposed HFS method is developed to solve this problem. To reduce the number of rules the HFS consists of a number of low-dimensional fuzzy systems in a hierarchical structure. In fact, by using HFS the total number of involved rules increases only linearly with the number of input variables. In the MPSS, to have better efficiency an auxiliary signal of reactive power deviation (ΔQ) is added with ΔP+ Δω input type Power system stabilizer (PSS). Phasor model of SVC is described and used in this paper. The performances of MPSS, Conventional power system stabilizer (CPSS), hierarchical Fuzzy Multi-input Power System Stabilizer (HFMPSS) and the proposed method in damping inter-area mode of oscillation are examined in response to disturbances. By using digital simulations the comparative study is illustrated. It can be seen that the proposed PSS is performing satisfactorily within the whole range of disturbances.
Abstract: The symmetric solution set Σ sym is the set of all solutions to the linear systems Ax = b, where A is symmetric and lies between some given bounds A and A, and b lies between b and b. We present a contractor for Σ sym, which is an iterative method that starts with some initial enclosure of Σ sym (by means of a cartesian product of intervals) and sequentially makes the enclosure tighter. Our contractor is based on polyhedral approximation and solving a series of linear programs. Even though it does not converge to the optimal bounds in general, it may significantly reduce the overestimation. The efficiency is discussed by a number of numerical experiments.
Abstract: Single-pole switching scheme is widely used in the
Extra High Voltage system. However, the substantial negativesequence
current injected to the turbine-generators imposes the
electromagnetic (E/M) torque of double system- frequency
components during the dead time (between single-pole clearing and
line reclosing). This would induce supersynchronous resonance
(SPSR) torque amplifications on low pressure turbine generator
blades and even lead to fatigue damage. This paper proposes the
design of a mechanical filter (MF) with natural frequency close to
double-system frequency. From the simulation results, it is found that
such a filter not only successfully damps the resonant effect, but also
has the characteristics of feasibility and compact.
Abstract: The modern telecommunication industry demands
higher capacity networks with high data rate. Orthogonal frequency
division multiplexing (OFDM) is a promising technique for high data
rate wireless communications at reasonable complexity in wireless
channels. OFDM has been adopted for many types of wireless
systems like wireless local area networks such as IEEE 802.11a, and
digital audio/video broadcasting (DAB/DVB). The proposed research
focuses on a concatenated coding scheme that improve the
performance of OFDM based wireless communications. It uses a
Redundant Residue Number System (RRNS) code as the outer code
and a convolutional code as the inner code. Here, a direct conversion
of analog signal to residue domain is done to reduce the conversion
complexity using sigma-delta based parallel analog-to-residue
converter. The bit error rate (BER) performances of the proposed
system under different channel conditions are investigated. These
include the effect of additive white Gaussian noise (AWGN),
multipath delay spread, peak power clipping and frame start
synchronization error. The simulation results show that the proposed
RRNS-Convolutional concatenated coding (RCCC) scheme provides
significant improvement in the system performance by exploiting the
inherent properties of RRNS.
Abstract: With the implied volatility as an important factor in
financial decision-making, in particular in option pricing valuation,
and also the given fact that the pricing biases of Leland option pricing
models and the implied volatility structure for the options are related,
this study considers examining the implied adjusted volatility smile
patterns and term structures in the S&P/ASX 200 index options using
the different Leland option pricing models. The examination of the
implied adjusted volatility smiles and term structures in the
Australian index options market covers the global financial crisis in
the mid-2007. The implied adjusted volatility was found to escalate
approximately triple the rate prior the crisis.
Abstract: The operation performance of a valveless micro-pump
is strongly dependent on the shape of connected nozzle/diffuser and
Reynolds number. The aims of present work are to compare the
performance curves of micropump with the original straight
nozzle/diffuser and contoured nozzle/diffuser under different back
pressure conditions. The tested valveless micropumps are assembled
of five pieces of patterned PMMA plates with hot-embracing
technique. The structures of central chamber, the inlet/outlet
reservoirs and the connected nozzle/diffuser are fabricated with laser
cutting machine. The micropump is actuated with circular-type PZT
film embraced on the bottom of central chamber. The deformation of
PZT membrane with various input voltages is measured with a
displacement laser probe. A simple testing facility is also constructed
to evaluate the performance curves for comparison.
In order to observe the evaluation of low Reynolds number
multiple vortex flow patterns within the micropump during suction
and pumping modes, the unsteady, incompressible laminar
three-dimensional Reynolds-averaged Navier-Stokes equations are
solved. The working fluid is DI water with constant thermo-physical
properties. The oscillating behavior of PZT film is modeled with the
moving boundary wall in way of UDF program. With the dynamic
mesh method, the instants pressure and velocity fields are obtained
and discussed.Results indicated that the volume flow rate is not
monotony increased with the oscillating frequency of PZT film,
regardless of the shapes of nozzle/diffuser. The present micropump
can generate the maximum volume flow rate of 13.53 ml/min when
the operation frequency is 64Hz and the input voltage is 140 volts.
The micropump with contoured nozzle/diffuser can provide 7ml/min
flow rate even when the back pressure is up to 400 mm-H2O. CFD
results revealed that the flow central chamber was occupied with
multiple pairs of counter-rotating vortices during suction and
pumping modes. The net volume flow rate over a complete
oscillating periodic of PZT
Abstract: This study was investigated on sampling and
analyzing water quality in water reservoir & water tower installed in
two kind of residential buildings and school facilities. Data of water
quality was collected for correlation analysis with frequency of
sanitization of water reservoir through questioning managers of
building about the inspection charts recorded on equipment for water
reservoir. Statistical software packages (SPSS) were applied to the
data of two groups (cleaning frequency and water quality) for
regression analysis to determine the optimal cleaning frequency of
sanitization. The correlation coefficient (R) in this paper represented
the degree of correlation, with values of R ranging from +1 to -1.After
investigating three categories of drinking water users; this study found
that the frequency of sanitization of water reservoir significantly
influenced the water quality of drinking water. A higher frequency of
sanitization (more than four times per 1 year) implied a higher quality
of drinking water. Results indicated that sanitizing water reservoir &
water tower should at least twice annually for achieving the aim of
safety of drinking water.
Abstract: We have measured the pressure drop and convective
heat transfer coefficient of water – based AL(25nm),AL2O3(30nm)
and CuO(50nm) Nanofluids flowing through a uniform heated
circular tube in the fully developed laminar flow regime. The
experimental results show that the data for Nanofluids friction factor
show a good agreement with analytical prediction from the Darcy's
equation for single-phase flow. After reducing the experimental
results to the form of Reynolds, Rayleigh and Nusselt numbers. The
results show the local Nusselt number and temperature have
distribution with the non-dimensional axial distance from the tube
entry. Study decided that thenNanofluid as Newtonian fluids through
the design of the linear relationship between shear stress and the rate
of stress has been the study of three chains of the Nanofluid with
different concentrations and where the AL, AL2O3 and CuO – water
ranging from (0.25 - 2.5 vol %). In addition to measuring the four
properties of the Nanofluid in practice so as to ensure the validity of
equations of properties developed by the researchers in this area and
these properties is viscosity, specific heat, and density and found that
the difference does not exceed 3.5% for the experimental equations
between them and the practical. The study also demonstrated that the
amount of the increase in heat transfer coefficient for three types of
Nano fluid is AL, AL2O3, and CuO – Water and these ratios are
respectively (45%, 32%, 25%) with insulation and without insulation
(36%, 23%, 19%), and the statement of any of the cases the best
increase in heat transfer has been proven that using insulation is
better than not using it. I have been using three types of Nano
particles and one metallic Nanoparticle and two oxide Nanoparticle
and a statement, whichever gives the best increase in heat transfer.
Abstract: PCCI engines can reduce NOx and PM emissions
simultaneously without sacrificing thermal efficiency, but a low
combustion temperature resulting from early fuel injection, and
ignition occurring prior to TDC, can cause higher THC and CO
emissions and fuel consumption. In conclusion, it was found that the
PCCI combustion achieved by the 2-stage injection strategy with
optimized calibration factors (e.g. EGR rate, injection pressure, swirl
ratio, intake pressure, injection timing) can reduce NOx and PM
emissions simultaneously. This research works are expected to
provide valuable information conducive to a development of an
innovative combustion engine that can fulfill upcoming stringent
emission standards.
Abstract: One of the main advantages of the LO paradigm is to
allow the availability of good quality, shareable learning material
through the Web. The effectiveness of the retrieval process requires a
formal description of the resources (metadata) that closely fits the
user-s search criteria; in spite of the huge international efforts in this
field, educational metadata schemata often fail to fulfil this
requirement. This work aims to improve the situation, by the
definition of a metadata model capturing specific didactic features of
shareable learning resources. It classifies LOs into “teacher-oriented"
and “student-oriented" categories, in order to describe the role a LO
is to play when it is integrated into the educational process. This
article describes the model and a first experimental validation process
that has been carried out in a controlled environment.
Abstract: The problem of robust stability and robust stabilization for a class of discrete-time uncertain systems with time delay is investigated. Based on Tchebychev inequality, by constructing a new augmented Lyapunov function, some improved sufficient conditions ensuring exponential stability and stabilization are established. These conditions are expressed in the forms of linear matrix inequalities (LMIs), whose feasibility can be easily checked by using Matlab LMI Toolbox. Compared with some previous results derived in the literature, the new obtained criteria have less conservatism. Two numerical examples are provided to demonstrate the improvement and effectiveness of the proposed method.
Abstract: The effect of extraction solvent upon properties
of carrageenan from Eucheuma cottonii was studied. The
distilled water and KOH solution (concentration 0.1- 0.5N) were
used as the solvent. Extraction process was carried out in water
bath equipped by stirrer with constant speed of 275 rpm with a
constant ratio of seaweed weight to solvent volume ( 1:50 g/mL)
at 86oC for 45 minutes. The extract was then precipitated in 3
volume of 90% ethanol, oven dried at 60oC. Based on
experimental data, alkali significantly influenced yield and
properties of extracted carrageenan. The extracted carrageenan
was found to have essentially identical FTIR spectra to the
reference samples of kappa-carrageenan. Increasing the KOH
concentration led to carrageenan containing less sulfate content
and intrinsic viscosity. The gel strength increased along with the
increasing of KOH concentration. The decreasing of intrinsic
viscosity value indicates that a polymer degradation occurs
during alkali extraction.
Abstract: The P-Bigram method is a string comparison methods
base on an internal two characters-based similarity measure. The edit
distance between two strings is the minimal number of elementary
editing operations required to transform one string into the other. The
elementary editing operations include deletion, insertion, substitution
two characters. In this paper, we address the P-Bigram method to
sole the similarity problem in DNA sequence. This method provided
an efficient algorithm that locates all minimum operation in a string.
We have been implemented algorithm and found that our program
calculated that smaller distance than one string. We develop PBigram
edit distance and show that edit distance or the similarity and
implementation using dynamic programming. The performance of
the proposed approach is evaluated using number edit and percentage
similarity measures.
Abstract: Chronic conditions carry with them strong emotions
and often lead to charged relationships between patients and their
health providers and, by extension, patients and health researchers.
Persons are both autonomous and relational and a purely cognitive
model of autonomy neglects the social and relational basis of chronic
illness. Ensuring genuine informed consent in research requires a
thorough understanding of how participants perceive a study and
their reasons for participation. Surveys may not capture the
complexities of reasoning that underlies study participation.
Contradictory reasons for participation, for instance an initial claim
of altruism as rationale and a subsequent claim of personal benefit
(therapeutic misconception), affect the quality of informed consent.
Individuals apply principles through the filter of personal values and
lived experience. Authentic autonomy, and hence authentic consent
to research, occurs within the context of patients- unique life
narratives and illness experiences.
Abstract: In this paper we propose a family of algorithms based
on 3rd and 4th order cumulants for blind single-input single-output
(SISO) Non-Minimum Phase (NMP) Finite Impulse Response (FIR)
channel estimation driven by non-Gaussian signal. The input signal
represents the signal used in 10GBASE-T (or IEEE 802.3an-2006)
as a Tomlinson-Harashima Precoded (THP) version of random
Pulse-Amplitude Modulation with 16 discrete levels (PAM-16). The
proposed algorithms are tested using three non-minimum phase
channel for different Signal-to-Noise Ratios (SNR) and for different
data input length. Numerical simulation results are presented to
illustrate the performance of the proposed algorithms.
Abstract: Grid composite structures have many applications in aerospace industry in which deal with transverse loadings abundantly. In present paper a stiffened composite cylindrical shell with clamped-free boundary condition under transverse end load experimentally and numerically was studied. Some electrical strain gauges were employed to measure the strains. Also a finite element analysis was done for validation of experimental result. The FEM software used was ANSYS11. In addition, the results between stiffened composite shell and unstiffened composite shell were compared. It was observed that intersection of two stiffeners has an important effect in decrease of stress in the shell. Fairly good agreements were observed between the numerical and the measured results. According to recent studies about grid composite structures, it should be noted that any investigation like this research has not been reported.
Abstract: System MEMORI automatically detects and recognizes rotated and/or rescaled versions of the objects of a database within digital color images with cluttered background. This task is accomplished by means of a region grouping algorithm guided by heuristic rules, whose parameters concern some geometrical properties and the recognition score of the database objects. This paper focuses on the strategies implemented in MEMORI for the estimation of the heuristic rule parameters. This estimation, being automatic, makes the system a highly user-friendly tool.
Abstract: In Korea, the technology of a load fo nuclear power plant has been being developed.
automatic controller which is able to control temperature and axial power distribution was developed. identification algorithm and a model predictive contact former transforms the nuclear reactor status into
numerically. And the latter uses them and ge
manipulated values such as two kinds of control ro
this automatic controller, the performance of a coperation was evaluated. As a result, the automatic generated model parameters of a nuclear react to nuclear reactor average temperature and axial power the desired targets during a daily load follow.
Abstract: In this competitive age, one of the key tools of most successful organizations is knowledge management. Today some organizations measure their current knowledge and use it as an indicator for rating the organization on their reports. Noting that the universities and colleges of medical science have a great role in public health of societies, their access to newest scientific research and the establishment of organizational knowledge management systems is very important. In order to explore the Application of Knowledge Management Factors, a national study was undertaken. The main purpose of this study was to find the rate of the application of knowledge management factors and some ways to establish more application of knowledge management system in Esfahan University-s Medical College (EUMC). Esfahan is the second largest city after Tehran, the capital city of Iran, and the EUMC is the biggest medical college in Esfahan. To rate the application of knowledge management, this study uses a quantitative research methodology based on Probst, Raub and Romhardt model of knowledge management. A group of 267 faculty members and staff of the EUMC were asked via questionnaire. Finding showed that the rate of the application of knowledge management factors in EUMC have been lower than average. As a result, an interview with ten faculty members conducted to find the guidelines to establish more applications of knowledge management system in EUMC.