Abstract: Roundabout work on the principle of circulation and
entry flows, where the maximum entry flow rates depend largely on
circulating flow bearing in mind that entry flows must give away to
circulating flows. Where an existing roundabout has a road hump
installed at the entry arm, it can be hypothesized that the kinematics
of vehicles may prevent the entry arm from achieving optimum
performance. Road humps are traffic calming devices placed across
road width solely as speed reduction mechanism. They are the
preferred traffic calming option in Malaysia and often used on single
and dual carriageway local routes. The speed limit on local routes is
30mph (50 km/hr). Road humps in their various forms achieved the
biggest mean speed reduction (based on a mean speed before traffic
calming of 30mph) of up to 10mph or 16 km/hr according to the UK
Department of Transport. The underlying aim of reduced speed
should be to achieve a 'safe' distribution of speeds which reflects the
function of the road and the impacts on the local community.
Constraining safe distribution of speeds may lead to poor drivers
timing and delayed reflex reaction that can probably cause accident.
Previous studies on road hump impact have focused mainly on speed
reduction, traffic volume, noise and vibrations, discomfort and delay
from the use of road humps. The paper is aimed at optimal entry and
circulating flow induced by road humps. Results show that
roundabout entry and circulating flow perform better in
circumstances where there is no road hump at entrance.
Abstract: Quality Function Deployment (QFD) is an expounded, multi-step planning method for delivering commodity, services, and processes to customers, both external and internal to an organization. It is a way to convert between the diverse customer languages expressing demands (Voice of the Customer), and the organization-s languages expressing results that sate those demands. The policy is to establish one or more matrices that inter-relate producer and consumer reciprocal expectations. Due to its visual presence is called the “House of Quality" (HOQ). In this paper, we assumed HOQ in multi attribute decision making (MADM) pattern and through a proposed MADM method, rank technical specifications. Thereafter compute satisfaction degree of customer requirements and for it, we apply vagueness and uncertainty conditions in decision making by fuzzy set theory. This approach would propound supervised neural network (perceptron) for MADM problem solving.
Abstract: The problem of FIR system parameter estimation has been considered in the paper. A new robust recursive algorithm for simultaneously estimation of parameters and scale factor of prediction residuals in non-stationary environment corrupted by impulsive noise has been proposed. The performance of derived algorithm has been tested by simulations.
Abstract: Gene, principal unit of inheritance, is an ordered
sequence of nucleotides. The genes of eukaryotic organisms include
alternating segments of exons and introns. The region of
Deoxyribonucleic acid (DNA) within a gene containing instructions
for coding a protein is called exon. On the other hand, non-coding
regions called introns are another part of DNA that regulates gene
expression by removing from the messenger Ribonucleic acid (RNA)
in a splicing process. This paper proposes to determine splice
junctions that are exon-intron boundaries by analyzing DNA
sequences. A splice junction can be either exon-intron (EI) or intron
exon (IE). Because of the popularity and compatibility of the
artificial neural network (ANN) in genetic fields; various ANN
models are applied in this research. Multi-layer Perceptron (MLP),
Radial Basis Function (RBF) and Generalized Regression Neural
Networks (GRNN) are used to analyze and detect the splice junctions
of gene sequences. 10-fold cross validation is used to demonstrate
the accuracy of networks. The real performances of these networks
are found by applying Receiver Operating Characteristic (ROC)
analysis.
Abstract: The purpose of this paper is to present two different
approaches of financial distress pre-warning models appropriate for
risk supervisors, investors and policy makers. We examine a sample
of the financial institutions and electronic companies of Taiwan
Security Exchange (TSE) market from 2002 through 2008. We
present a binary logistic regression with paned data analysis. With
the pooled binary logistic regression we build a model including
more variables in the regression than with random effects, while the
in-sample and out-sample forecasting performance is higher in
random effects estimation than in pooled regression. On the other
hand we estimate an Adaptive Neuro-Fuzzy Inference System
(ANFIS) with Gaussian and Generalized Bell (Gbell) functions and
we find that ANFIS outperforms significant Logit regressions in both
in-sample and out-of-sample periods, indicating that ANFIS is a
more appropriate tool for financial risk managers and for the
economic policy makers in central banks and national statistical
services.
Abstract: Carbon nanotubes (CNTs) with their high mechanical,
electrical, thermal and chemical properties are regarded as promising
materials for many different potential applications. Having unique
properties they can be used in a wide range of fields such as
electronic devices, electrodes, drug delivery systems, hydrogen
storage, textile etc. Catalytic chemical vapor deposition (CCVD) is a
common method for CNT production especially for mass production.
Catalysts impregnated on a suitable substrate are important for
production with chemical vapor deposition (CVD) method. Iron
catalyst and MgO substrate is one of most common catalyst-substrate
combination used for CNT. In this study, CNTs were produced by
CCVD of acetylene (C2H2) on magnesium oxide (MgO) powder
substrate impregnated by iron nitrate (Fe(NO3)3•9H2O) solution. The
CNT synthesis conditions were as follows: at synthesis temperatures
of 500 and 800°C multiwall and single wall CNTs were produced
respectively. Iron (Fe) catalysts were prepared by with Fe:MgO ratio
of 1:100, 5:100 and 10:100. The duration of syntheses were 30 and
60 minutes for all temperatures and catalyst percentages. The
synthesized materials were characterized by thermal gravimetric
analysis (TGA), transmission electron microscopy (TEM) and Raman
spectroscopy.
Abstract: The three-time-scale plant model of a wind power
generator, including a wind turbine, a flexible vertical shaft, a Variable
Inertia Flywheel (VIF) module, an Active Magnetic Bearing (AMB)
unit and the applied wind sequence, is constructed. In order to make
the wind power generator be still able to operate as the spindle speed
exceeds its rated speed, the VIF is equipped so that the spindle speed
can be appropriately slowed down once any stronger wind field is
exerted. To prevent any potential damage due to collision by shaft
against conventional bearings, the AMB unit is proposed to regulate
the shaft position deviation. By singular perturbation order-reduction
technique, a lower-order plant model can be established for the
synthesis of feedback controller. Two major system parameter
uncertainties, an additive uncertainty and a multiplicative uncertainty,
are constituted by the wind turbine and the VIF respectively.
Frequency Shaping Sliding Mode Control (FSSMC) loop is proposed
to account for these uncertainties and suppress the unmodeled
higher-order plant dynamics. At last, the efficacy of the FSSMC is
verified by intensive computer and experimental simulations for
regulation on position deviation of the shaft and counter-balance of
unpredictable wind disturbance.
Abstract: The main focus of the work was concerned with hydrodynamic and thermal analysis of the plate heat exchanger channel with corrugation patterns suggested to be triangular, sinusoidal, and square corrugation. This study was to numerically model and validate the triangular corrugated channel with dimensions/parameters taken from open literature, and then model/analyze both sinusoidal, and square corrugated channel referred to the triangular model. Initially, 2D modeling with local extensive analysis for triangular corrugated channel was carried out. By that, all local pressure drop, wall shear stress, friction factor, static temperature, heat flux, Nusselt number, and surface heat coefficient, were analyzed to interpret the hydrodynamic and thermal phenomena occurred in the flow. Furthermore, in order to facilitate confidence in this model, a comparison between the values predicted, and experimental results taken from literature for almost the same case, was done. Moreover, a holistic numerical study for sinusoidal and square channels together with global comparisons with triangular corrugation under the same condition, were handled. Later, a comparison between electric, and fluid cooling through varying the boundary condition was achieved. The constant wall temperature and constant wall heat flux boundary conditions were employed, and the different resulted Nusselt numbers as a consequence were justified. The results obtained can be used to come up with an optimal design, a 'compromise' between heat transfer and pressure drop.
Abstract: This paper presents an investigation of the power
penalties imposed by four-wave mixing (FWM) on G.652 (Single-
Mode Fiber - SMF), G.653 (Dispersion-Shifted Fiber - DSF), and
G.655 (Non-Zero Dispersion-Shifted Fiber - NZDSF) compliant
fibers, considering the DWDM grids suggested by the ITU-T
Recommendations G.692, and G.694.1, with uniform channel
spacing of 100, 50, 25, and 12.5 GHz. The mathematical/numerical
model assumes undepleted pumping, and shows very clearly the
deleterious effect of FWM on the performance of DWDM systems,
measured by the signal-to-noise ratio (SNR). The results make it
evident that non-uniform channel spacing is practically mandatory
for WDM systems based on DSF fibers.
Abstract: In this paper, we consider the almost periodic solutions of a discrete cooperation system with feedback controls. Assuming that the coefficients in the system are almost periodic sequences, we obtain the existence and uniqueness of the almost periodic solution which is uniformly asymptotically stable.
Abstract: Two-dimensional Direct Numerical Simulation (DNS)
of high Schmidt number mass transfer in a convective flow environment
(Rayleigh-B'enard) is carried out and results are compared to
experimental data. A fourth-order accurate WENO-scheme has been
used for scalar transport in order to aim for a high accuracy in areas
of high concentration gradients. It was found that the typical spatial
distance between downward plumes of cold high concentration water
and the eddy size are in good agreement with experiments using a
combined PIV-LIF technique for simultaneous and spatially synoptic
measurements of 2D velocity and concentration fields.
Abstract: One important problem in today organizations is the
existence of non-integrated information systems, inconsistency and
lack of suitable correlations between legacy and modern systems.
One main solution is to transfer the local databases into a global one.
In this regards we need to extract the data structures from the legacy
systems and integrate them with the new technology systems. In
legacy systems, huge amounts of a data are stored in legacy
databases. They require particular attention since they need more
efforts to be normalized, reformatted and moved to the modern
database environments. Designing the new integrated (global)
database architecture and applying the reverse engineering requires
data normalization. This paper proposes the use of database reverse
engineering in order to integrate legacy and modern databases in
organizations. The suggested approach consists of methods and
techniques for generating data transformation rules needed for the
data structure normalization.
Abstract: The study of the transport coefficients in electronic
devices is currently carried out by analytical and empirical models.
This study requires several simplifying assumptions, generally
necessary to lead to analytical expressions in order to study the
different characteristics of the electronic silicon-based devices.
Further progress in the development, design and optimization of
Silicon-based devices necessarily requires new theory and modeling
tools. In our study, we use the PSO (Particle Swarm Optimization)
technique as a computational tool to develop analytical approaches in
order to study the transport phenomenon of the electron in crystalline
silicon as function of temperature and doping concentration. Good
agreement between our results and measured data has been found.
The optimized analytical models can also be incorporated into the
circuits simulators to study Si-based devices without impact on the
computational time and data storage.
Abstract: Twist drills are geometrical complex tools and thus various researchers have adopted different mathematical and experimental approaches for their simulation. The present paper acknowledges the increasing use of modern CAD systems and using the API (Application Programming Interface) of a CAD system, drilling simulations are carried out. The developed DRILL3D software routine, creates parametrically controlled tool geometries and using different cutting conditions, achieves the generation of solid models for all the relevant data involved (drilling tool, cut workpiece, undeformed chip). The final data derived, consist a platform for further direct simulations regarding the determination of cutting forces, tool wear, drilling optimizations etc.
Abstract: We consider a heterogeneously mixing SIR stochastic
epidemic process in populations described by a general graph.
Likelihood theory is developed to facilitate statistic inference for the
parameters of the model under complete observation. We show that
these estimators are asymptotically Gaussian unbiased estimates by
using a martingale central limit theorem.
Abstract: Automatic face detection is a complex problem in
image processing. Many methods exist to solve this problem such as
template matching, Fisher Linear Discriminate, Neural Networks,
SVM, and MRC. Success has been achieved with each method to
varying degrees and complexities. In proposed algorithm we used
upright, frontal faces for single gray scale images with decent
resolution and under good lighting condition. In the field of face
recognition technique the single face is matched with single face
from the training dataset. The author proposed a neural network
based face detection algorithm from the photographs as well as if any
test data appears it check from the online scanned training dataset.
Experimental result shows that the algorithm detected up to 95%
accuracy for any image.
Abstract: A high performance computer includes a fast
processor and millions bytes of memory. During the data processing,
huge amount of information are shuffled between the memory and
processor. Because of its small size and its effectiveness speed, cache
has become a common feature of high performance computers.
Enhancing cache performance proved to be essential in the speed up
of cache-based computers. Most enhancement approaches can be
classified as either software based or hardware controlled. The
performance of the cache is quantified in terms of hit ratio or miss
ratio. In this paper, we are optimizing the cache performance based
on enhancing the cache hit ratio. The optimum cache performance is
obtained by focusing on the cache hardware modification in the way
to make a quick rejection to the missed line's tags from the hit-or
miss comparison stage, and thus a low hit time for the wanted line in
the cache is achieved. In the proposed technique which we called
Even- Odd Tabulation (EOT), the cache lines come from the main
memory into cache are classified in two types; even line's tags and
odd line's tags depending on their Least Significant Bit (LSB). This
division is exploited by EOT technique to reject the miss match line's
tags in very low time compared to the time spent by the main
comparator in the cache, giving an optimum hitting time for the
wanted cache line. The high performance of EOT technique against
the familiar mapping technique FAM is shown in the simulated
results.
Abstract: The purpose of this study was to study postpartum breastfeeding mothers to determine the impact their psychosocial and spiritual dimensions play in promoting full-term (6 month duration) breastfeeding of their infants. Purposive and snowball sampling methods were used to identify and recruit the study's participants. A total of 23 postpartum mothers, who were breastfeeding within 6 weeks after giving birth, participated in this study. In-depth interviews combined with observations, participant focus groups, and ethnographic records were used for data collection. The Data were then analyzed using content analysis and typology. The results of this study illustrated that postpartum mothers experienced fear and worry that they would lack support from their spouse, family and peers, and that their infant would not get enough milk It was found that the main barrier mothers faced in breastfeeding to full-term was the difficulty of continuing to breastfeed when returning to work. 81.82% of the primiparous mothers and 91.67% of the non-primiparous mothers were able to breastfeed for the desired full-term of 6 months. Factors found to be related to breastfeeding for six months included 1) belief and faith in breastfeeding, 2) support from spouse and family members, 3) counseling from public health nurses and friends. The sample also provided evidence that religious principles such as tolerance, effort, love, and compassion to their infant, and positive thinking, were used in solving their physical, mental and spiritual problems.
Abstract: The influence of axial magnetic field (B=0.48 T) on
the variation of ionization efficiency coefficient h and secondary
electron emission coefficient g with respect to reduced electric field
E/P is studied at a new range of plane-parallel electrode spacing (0<
d< 20 cm) and different nitrogen working pressure between 0.5-20
Pa. The axial magnetic field is produced from an inductive copper
coil of radius 5.6 cm. The experimental data of breakdown voltage is
adopted to estimate the mean Paschen curves at different working
features. The secondary electron emission coefficient is calculated
from the mean Paschen curve and used to determine the minimum
breakdown voltage. A reduction of discharge voltage of about 25% is
investigated by the applied of axial magnetic field. At high interelectrode
spacing, the effect of axial magnetic field becomes more
significant for the obtained values of h but it was less for the values
of g.
Abstract: The dynamic behaviour of a four-bar linkage driven by a velocity controlled DC motor is discussed in the paper. In particular the author presents the results obtained by means of a specifically developed software, which implements the mathematical models of all components of the system (linkage, transmission, electric motor, control devices). The use of this software enables a more efficient design approach, since it allows the designer to check, in a simple and immediate way, the dynamic behaviour of the mechanism, arising from different values of the system parameters.