Abstract: In comparison to the original SVM, which involves a
quadratic programming task; LS–SVM simplifies the required
computation, but unfortunately the sparseness of standard SVM is
lost. Another problem is that LS-SVM is only optimal if the training
samples are corrupted by Gaussian noise. In Least Squares SVM
(LS–SVM), the nonlinear solution is obtained, by first mapping the
input vector to a high dimensional kernel space in a nonlinear
fashion, where the solution is calculated from a linear equation set. In
this paper a geometric view of the kernel space is introduced, which
enables us to develop a new formulation to achieve a sparse and
robust estimate.
Abstract: Experiments have been carried out at sub-critical
Reynolds number to investigate free-to-roll motions induced by
forebody and/or wings complex flow on a 30° swept back nonslender
wings-slender body-model for static and dynamic (pitch-up)
cases. For the dynamic (pitch-up) case it has been observed that roll
amplitude decreases and lag increases with increase in pitching
speed. Decrease in roll amplitude with increase in pitch rate is
attributed to low disturbing rolling moment due to weaker interaction
between forebody and wing flow components. Asymmetric forebody
vortices dominate and control the roll motion of the model in
dynamic case when non-dimensional pitch rate ≥ 1x10-2.
Effectiveness of the active control scheme utilizing rotating nose with
artificial tip perturbation is observed to be low in the angle of attack
region where the complex flow over the wings has contributions from
both forebody and wings.
Abstract: Sparse representation which can represent high dimensional
data effectively has been successfully used in computer vision
and pattern recognition problems. However, it doesn-t consider the
label information of data samples. To overcome this limitation,
we develop a novel dimensionality reduction algorithm namely
dscriminatively regularized sparse subspace learning(DR-SSL) in this
paper. The proposed DR-SSL algorithm can not only make use of
the sparse representation to model the data, but also can effective
employ the label information to guide the procedure of dimensionality
reduction. In addition,the presented algorithm can effectively deal
with the out-of-sample problem.The experiments on gene-expression
data sets show that the proposed algorithm is an effective tool for
dimensionality reduction and gene-expression data classification.
Abstract: The primary purpose of this article is an attempt to
find the implication of globalization on education. Globalization has
an important role as a process in the economical, political, cultural
and technological dimensions in the life of the contemporary human
being and has been affected by it. Education has its effects in this
procedure and while influencing it through educating global citizens
having universal human features and characteristics, has been
influenced by this phenomenon too. Nowadays, the role of education
is not just to develop in the students the knowledge and skills
necessary for the new kinds of jobs. If education wants to help
students be prepared of the new global society, it has to make them
engaged productive and critical citizens for the global era, so that
they can reflect about their roles as key actors in a dynamic often
uneven, matrix of economic and cultural exchanges. If education
wants to reinforce and raise the national identity, the value system
and the children and teenagers, it should make them ready for living
in the global era of this century. The used method in this research is
documentary and analyzing the documents. Studies in this field show
globalization has influences on the processes of the production,
distribution and consuming of knowledge. The happening of this
event in the information era has not only provide the necessary
opportunities for the exchanges of education worldwide but also has
privileges for the developing countries which enables them to
strengthen educational bases of their society and have an important
step toward their future.
Abstract: In the present work steady inviscid hypersonic flows
are calculated by approximate Method. Maslens' inverse method is the chosen approximate method. For the inverse problem, parabolic
shock shape is chosen for the two-dimensional flow, and the body shape and flow field are calculated using Maslen's method. For the axisymmetric inverse problem paraboloidal shock is chosen and the
surface distribution of pressure is obtained.
Abstract: The broadcast problem including the plan design is
considered. The data are inserted and numbered at predefined order
into customized size relations. The server ability to create a full,
regular Broadcast Plan (RBP) with single and multiple channels after
some data transformations is examined. The Regular Geometric
Algorithm (RGA) prepares a RBP and enables the users to catch their
items avoiding energy waste of their devices. Moreover, the
Grouping Dimensioning Algorithm (GDA) based on integrated
relations can guarantee the discrimination of services with a
minimum number of channels. This last property among the selfmonitoring,
self-organizing, can be offered by servers today
providing also channel availability and less energy consumption by
using smaller number of channels. Simulation results are provided.
Abstract: The main focus of the work was concerned with hydrodynamic and thermal analysis of the plate heat exchanger channel with corrugation patterns suggested to be triangular, sinusoidal, and square corrugation. This study was to numerically model and validate the triangular corrugated channel with dimensions/parameters taken from open literature, and then model/analyze both sinusoidal, and square corrugated channel referred to the triangular model. Initially, 2D modeling with local extensive analysis for triangular corrugated channel was carried out. By that, all local pressure drop, wall shear stress, friction factor, static temperature, heat flux, Nusselt number, and surface heat coefficient, were analyzed to interpret the hydrodynamic and thermal phenomena occurred in the flow. Furthermore, in order to facilitate confidence in this model, a comparison between the values predicted, and experimental results taken from literature for almost the same case, was done. Moreover, a holistic numerical study for sinusoidal and square channels together with global comparisons with triangular corrugation under the same condition, were handled. Later, a comparison between electric, and fluid cooling through varying the boundary condition was achieved. The constant wall temperature and constant wall heat flux boundary conditions were employed, and the different resulted Nusselt numbers as a consequence were justified. The results obtained can be used to come up with an optimal design, a 'compromise' between heat transfer and pressure drop.
Abstract: Two-dimensional Direct Numerical Simulation (DNS)
of high Schmidt number mass transfer in a convective flow environment
(Rayleigh-B'enard) is carried out and results are compared to
experimental data. A fourth-order accurate WENO-scheme has been
used for scalar transport in order to aim for a high accuracy in areas
of high concentration gradients. It was found that the typical spatial
distance between downward plumes of cold high concentration water
and the eddy size are in good agreement with experiments using a
combined PIV-LIF technique for simultaneous and spatially synoptic
measurements of 2D velocity and concentration fields.
Abstract: In this paper, He-s homotopy perturbation method (HPM) is applied to spatial one and three spatial dimensional inhomogeneous wave equation Cauchy problems for obtaining exact solutions. HPM is used for analytic handling of these equations. The results reveal that the HPM is a very effective, convenient and quite accurate to such types of partial differential equations (PDEs).
Abstract: The purpose of this study was to study postpartum breastfeeding mothers to determine the impact their psychosocial and spiritual dimensions play in promoting full-term (6 month duration) breastfeeding of their infants. Purposive and snowball sampling methods were used to identify and recruit the study's participants. A total of 23 postpartum mothers, who were breastfeeding within 6 weeks after giving birth, participated in this study. In-depth interviews combined with observations, participant focus groups, and ethnographic records were used for data collection. The Data were then analyzed using content analysis and typology. The results of this study illustrated that postpartum mothers experienced fear and worry that they would lack support from their spouse, family and peers, and that their infant would not get enough milk It was found that the main barrier mothers faced in breastfeeding to full-term was the difficulty of continuing to breastfeed when returning to work. 81.82% of the primiparous mothers and 91.67% of the non-primiparous mothers were able to breastfeed for the desired full-term of 6 months. Factors found to be related to breastfeeding for six months included 1) belief and faith in breastfeeding, 2) support from spouse and family members, 3) counseling from public health nurses and friends. The sample also provided evidence that religious principles such as tolerance, effort, love, and compassion to their infant, and positive thinking, were used in solving their physical, mental and spiritual problems.
Abstract: This paper describes the results and implications of a correlational study of learning styles and learner satisfaction. The relationship of these empirical concepts was examined in the context of traditional versus e-blended modes of course delivery in an introductory graduate research course. Significant results indicated that the visual side of the visual-verbal dimension of students- learning style(s) was positively correlated to satisfaction with themselves as learners in an e-blended course delivery mode and negatively correlated to satisfaction with the classroom environment in the context of a traditional classroom course delivery mode.
Abstract: The Wavelet-Galerkin finite element method for
solving the one-dimensional heat equation is presented in this work.
Two types of basis functions which are the Lagrange and multi-level
wavelet bases are employed to derive the full form of matrix system.
We consider both linear and quadratic bases in the Galerkin method.
Time derivative is approximated by polynomial time basis that
provides easily extend the order of approximation in time space. Our
numerical results show that the rate of convergences for the linear
Lagrange and the linear wavelet bases are the same and in order 2
while the rate of convergences for the quadratic Lagrange and the
quadratic wavelet bases are approximately in order 4. It also reveals
that the wavelet basis provides an easy treatment to improve
numerical resolutions that can be done by increasing just its desired
levels in the multilevel construction process.
Abstract: Experimental data from an atmospheric air/water terrain slugging case has been made available by the Shell Amsterdam research center, and has been subject to numerical simulation and comparison with a one-dimensional two-phase slug tracking simulator under development at the Norwegian University of Science and Technology. The code is based on tracking of liquid slugs in pipelines by use of a Lagrangian grid formulation implemented in Cµ by use of object oriented techniques. An existing hybrid spatial discretization scheme is tested, in which the stratified regions are modelled by the two-fluid model. The slug regions are treated incompressible, thus requiring a single momentum balance over the whole slug. Upon comparison with the experimental data, the period of the simulated severe slugging cycle is observed to be sensitive to slug generation in the horizontal parts of the system. Two different slug initiation methods have been tested with the slug tracking code, and grid dependency has been investigated.
Abstract: A series of tests on cold-formed steel (CFS) wall plate system subjected to uplift force at the mid span of the wall plate is presented. The aim of the study was to study the behaviour and identify the modes of failure of CFS wall plate system. Two parameters were considered in these studies: 1) different dimension of U-bracket at the supports and 2) different sizes of lipped C-channel. The lipped C-channels used were C07508, C07512 and C10012. The dimensions of the leg of U-bracket were 50x35 mm and 50x60 mm respectively, where 25 mm clearance was provided to the connections for specimens with clearance. Results show that specimens with and without clearance experienced the same mode of failure. Failure began with the yielding of the connectors followed by distortional buckling of the wall plate. However, when C075 sections were used as wall plate, the system behaved differently. There was a large deformation in the wall plate and failure began in the distortional buckling of the wall plate followed by bearing of the connecting plates at the supports (U-bracket). The ultimate strength of the system also decreased dramatically when C075 sections were used.
Abstract: A new design of a planar passive T-micromixer with fin-shaped baffles in the mixing channel is presented. The mixing efficiency and the level of pressure loss in the channel have been investigated by numerical simulations in the range of Reynolds number (Re) 1 to 50. A Mixing index (Mi) has been defined to quantify the mixing efficiency, which results over 85% at both ends of the Re range, what demonstrates the micromixer can enhance mixing using the mechanisms of diffusion (lower Re) and convection (higher Re). Three geometric dimensions: radius of baffle, baffles pitch and height of the channel define the design parameters, and the mixing index and pressure loss are the performance parameters used to optimize the micromixer geometry with a multi-criteria optimization method. The Pareto front of designs with the optimum trade-offs, maximum mixing index with minimum pressure loss, is obtained. Experiments for qualitative and quantitative validation have been implemented.
Abstract: Organizational culture fosters innovation, and innovation is the main engine to be sustained within the uncertainty market. Like other countries, the construction industry significantly contributes to the economy, society and technology of Malaysia, yet, innovation is still considered slow compared to other industries such as manufacturing. Given the important role of an architect as the key player and the contributor of new ideas in the construction industry, there is a call to identify the issue and improve the current situation by focusing on the architectural firms. In addition, the existing studies tend to focus only on a few dimensions of organizational culture and very few studies consider whether innovation is being generated or adopted. Hence, the present research tends to fill in the gap by identifying the organizational cultures that foster or hinder innovation generation and/or innovation adoption, and propose a model of organizational culture and innovation generation and/or adoption.
Abstract: This paper proposes the application of a hierarchical fuzzy system (HFS) based on multi-input power system stabilizer (MPSS) and also Static Var Compensator (SVC) in multi-machine environment.The number of rules grows exponentially with the number of variables in a conventional fuzzy logic system. The proposed HFS method is developed to solve this problem. To reduce the number of rules the HFS consists of a number of low-dimensional fuzzy systems in a hierarchical structure. In fact, by using HFS the total number of involved rules increases only linearly with the number of input variables. In the MPSS, to have better efficiency an auxiliary signal of reactive power deviation (ΔQ) is added with ΔP+ Δω input type Power system stabilizer (PSS). Phasor model of SVC is described and used in this paper. The performances of MPSS, Conventional power system stabilizer (CPSS), hierarchical Fuzzy Multi-input Power System Stabilizer (HFMPSS) and the proposed method in damping inter-area mode of oscillation are examined in response to disturbances. By using digital simulations the comparative study is illustrated. It can be seen that the proposed PSS is performing satisfactorily within the whole range of disturbances.
Abstract: The operation performance of a valveless micro-pump
is strongly dependent on the shape of connected nozzle/diffuser and
Reynolds number. The aims of present work are to compare the
performance curves of micropump with the original straight
nozzle/diffuser and contoured nozzle/diffuser under different back
pressure conditions. The tested valveless micropumps are assembled
of five pieces of patterned PMMA plates with hot-embracing
technique. The structures of central chamber, the inlet/outlet
reservoirs and the connected nozzle/diffuser are fabricated with laser
cutting machine. The micropump is actuated with circular-type PZT
film embraced on the bottom of central chamber. The deformation of
PZT membrane with various input voltages is measured with a
displacement laser probe. A simple testing facility is also constructed
to evaluate the performance curves for comparison.
In order to observe the evaluation of low Reynolds number
multiple vortex flow patterns within the micropump during suction
and pumping modes, the unsteady, incompressible laminar
three-dimensional Reynolds-averaged Navier-Stokes equations are
solved. The working fluid is DI water with constant thermo-physical
properties. The oscillating behavior of PZT film is modeled with the
moving boundary wall in way of UDF program. With the dynamic
mesh method, the instants pressure and velocity fields are obtained
and discussed.Results indicated that the volume flow rate is not
monotony increased with the oscillating frequency of PZT film,
regardless of the shapes of nozzle/diffuser. The present micropump
can generate the maximum volume flow rate of 13.53 ml/min when
the operation frequency is 64Hz and the input voltage is 140 volts.
The micropump with contoured nozzle/diffuser can provide 7ml/min
flow rate even when the back pressure is up to 400 mm-H2O. CFD
results revealed that the flow central chamber was occupied with
multiple pairs of counter-rotating vortices during suction and
pumping modes. The net volume flow rate over a complete
oscillating periodic of PZT
Abstract: In this paper we present a novel approach for human
Body configuration based on the Silhouette. We propose to address
this problem under the Bayesian framework. We use an effective
Model based MCMC (Markov Chain Monte Carlo) method to solve
the configuration problem, in which the best configuration could be
defined as MAP (maximize a posteriori probability) in Bayesian
model. This model based MCMC utilizes the human body model to
drive the MCMC sampling from the solution space. It converses the
original high dimension space into a restricted sub-space constructed
by the human model and uses a hybrid sampling algorithm. We
choose an explicit human model and carefully select the likelihood
functions to represent the best configuration solution. The
experiments show that this method could get an accurate
configuration and timesaving for different human from multi-views.
Abstract: We have measured the pressure drop and convective
heat transfer coefficient of water – based AL(25nm),AL2O3(30nm)
and CuO(50nm) Nanofluids flowing through a uniform heated
circular tube in the fully developed laminar flow regime. The
experimental results show that the data for Nanofluids friction factor
show a good agreement with analytical prediction from the Darcy's
equation for single-phase flow. After reducing the experimental
results to the form of Reynolds, Rayleigh and Nusselt numbers. The
results show the local Nusselt number and temperature have
distribution with the non-dimensional axial distance from the tube
entry. Study decided that thenNanofluid as Newtonian fluids through
the design of the linear relationship between shear stress and the rate
of stress has been the study of three chains of the Nanofluid with
different concentrations and where the AL, AL2O3 and CuO – water
ranging from (0.25 - 2.5 vol %). In addition to measuring the four
properties of the Nanofluid in practice so as to ensure the validity of
equations of properties developed by the researchers in this area and
these properties is viscosity, specific heat, and density and found that
the difference does not exceed 3.5% for the experimental equations
between them and the practical. The study also demonstrated that the
amount of the increase in heat transfer coefficient for three types of
Nano fluid is AL, AL2O3, and CuO – Water and these ratios are
respectively (45%, 32%, 25%) with insulation and without insulation
(36%, 23%, 19%), and the statement of any of the cases the best
increase in heat transfer has been proven that using insulation is
better than not using it. I have been using three types of Nano
particles and one metallic Nanoparticle and two oxide Nanoparticle
and a statement, whichever gives the best increase in heat transfer.