Abstract: Nowadays, the focus on renewable energy and alternative fuels has increased due to increasing oil prices, environment pollution, and also concern on preserving the nature. Biodiesel has been known as an attractive alternative fuel although biodiesel produced from edible oil is very expensive than conventional diesel. Therefore, the uses of biodiesel produced from non-edible oils are much better option. Currently Jatropha biodiesel (JBD) is receiving attention as an alternative fuel for diesel engine. Biodiesel is non-toxic, biodegradable, high lubricant ability, highly renewable, and its use therefore produces real reduction in petroleum consumption and carbon dioxide (CO2) emissions. Although biodiesel has many advantages, but it still has several properties need to improve, such as lower calorific value, lower effective engine power, higher emission of nitrogen oxides (NOX) and greater sensitivity to low temperature. Exhaust gas recirculation (EGR) is effective technique to reduce NOX emission from diesel engines because it enables lower flame temperature and oxygen concentration in the combustion chamber. Some studies succeeded to reduce the NOX emission from biodiesel by EGR but they observed increasing soot emission. The aim of this study was to investigate the engine performance and soot emission by using blended Jatropha biodiesel with different EGR rates. A CI engine that is water-cooled, turbocharged, using indirect injection system was used for the investigation. Soot emission, NOX, CO2, carbon monoxide (CO) were recorded and various engine performance parameters were also evaluated.
Abstract: The impact assessment in its various forms has
recently become a very important part of policy-making and
legislation in many different countries. Regulatory impact assessment
(RIA) is yet another set of analytical methods deployed in the
legislation of the European Union, of many developed countries as
well as in many developing ones such as Mexico, Malaysia and
Philippines. The aim of this paper is to provide a theoretical
background for economic models in regulatory impact assessment
and an overview of their application especially on the financial
market in the Czech Republic. We found out an inadequate
application of these models, what makes room for further research in
this field.
Abstract: Planning capacities when regenerating complex investment goods involves particular challenges in that the planning is subject to a large degree of uncertainty regarding load information. Using information fusion – by applying Bayesian Networks – a method is being developed for forecasting the anticipated expenditures (human labor, tool and machinery utilization, time etc.) for regenerating a good. The generated forecasts then later serve as a tool for planning capacities and ensure a greater stability in the planning processes.
Abstract: Canola is a specific edible type of rapeseed, developed
in the 1970s, which contains about 40 percent oil. This research was
carried out to determine the yield and some quality characteristics of
some winter canola cultivars during the 2010-2011 vegetation period
in Central Anatolia of Turkey. In this research; Oase, Dante,
Californium, Excalibur, Elvis, ES Hydromel, Licord, Orkan, Vectra,
Nelson, Champlain and NK Petrol winter canola varieties were used
as material. The field experiment was set up in a “Randomized
Complete Block Design” with three replications on 21 September
2010. In this research; seed yield, oil content, protein content, oil
yield and protein yield were examined.
As a result of this research; seed yield, oil content, oil yield and
protein yield (except protein content) were significant differences
between the cultivars. The highest seed yield (6348 kg ha-1) was
obtained from the NK Petrol, while the lowest seed yield (3949 kg
ha-1) was determined from the Champlain cultivar was obtained. The
highest oil content (46.73%) was observed from Oase and the lowest
value was obtained from Vectra (41.87%) cultivar. The highest oil
yield (2950 kg ha-1) was determined from NK Petrol while the least
value (1681 kg ha-1) was determined from Champlain cultivar. The
highest protein yield (1539.3 kg ha-1) was obtained from NK Petrol
and the lowest protein yield (976.5 kg ha-1) was obtained from
Champlain cultivar.
The main purpose of the cultivation of oil crops, to increase the
yield of oil per unit area. According the result of this research, NK
Petrol cultivar which ranks first with regard to both seed yield and oil
yield between cultivars as the most suitable winter canola cultivar of
local conditions.
Abstract: In the current economy of increasing global
competition, many organizations are attempting to use knowledge as
one of the means to gain sustainable competitive advantage. Besides
large organizations, the success of SMEs can be linked to how well
they manage their knowledge. Despite the profusion of research
about knowledge management within large organizations, fewer
studies tried to analyze KM in SMEs.
This research proposes a new framework showing the determinant
role of organizational dimensions onto KM approaches. The paper
and its propositions are based on a literature review and analysis.
In this research, personalization versus codification,
individualization versus institutionalization and IT-based versus non
IT-based are highlighted as three distinct dimensions of knowledge
management approaches.
The study contributes to research by providing a more nuanced
classification of KM approaches and provides guidance to managers
about the types of KM approaches that should be adopted based on
the size, geographical dispersion and task nature of SMEs.
To the author-s knowledge, the paper is the first of its kind to
examine if there are suitable configurations of KM approaches for
SMEs with different dimensions. It gives valuable information, which
hopefully will help SME sector to accomplish KM.
Abstract: International markets driven forces are changing
continuously, therefore companies need to gain a competitive edge in
such markets. Improving the company's products, processes and
practices is no longer auxiliary. Lean production is a production
management philosophy that consolidates work tasks with minimum
waste resulting in improved productivity. Lean production practices
can be mapped into many production areas. One of these is
Manufacturing Equipment and Technology (MET). Many lean
production practices can be implemented in MET, namely, specific
equipment configurations, total preventive maintenance, visual
control, new equipment/ technologies, production process
reengineering and shared vision of perfection.The purpose of this
paper is to investigate the implementation level of these six practices
in Jordanian industries. To achieve that a questionnaire survey has
been designed according to five-point Likert scale. The questionnaire
is validated through pilot study and through experts review. A sample
of 350 Jordanian companies were surveyed, the response rate was
83%. The respondents were asked to rate the extent of
implementation for each of practices. A relationship conceptual
model is developed, hypotheses are proposed, and consequently the
essential statistical analyses are then performed. An assessment tool
that enables management to monitor the progress and the
effectiveness of lean practices implementation is designed and
presented. Consequently, the results show that the average
implementation level of lean practices in MET is 77%, Jordanian
companies are implementing successfully the considered lean
production practices, and the presented model has Cronbach-s alpha
value of 0.87 which is good evidence on model consistency and
results validation.
Abstract: Biodiesel is traditionally produced from oleaginous
plants. On the other hand, increasing biodiesel production from these
raw materials could create problems of food supply. Producing
biodiesel from microalgae could help to overcome this difficulty,
because microalgae are rich in lipids and do not compete for arable
lands. However, no studies had compared vegetable and microalgae
oil-based biodiesel in terms of yield, viscosity and heat of
combustion. In the present study, commercial canola and microalgae
oil were therefore transesterified with methanol under a homogenous
alkali catalyst (potassium hydroxide) at 100oC for 1h. The result
showed that microalgae-based oil has a higher yield in biodiesel with
89.7% (g biodiesel/g oil) and a lower kinematic viscosity (22oC) of
4.31 mm/s2 than canola oil.
Abstract: This study was conducted to determine the
effect of abdominal exercises versus abdominal supporting
belt on abdominal efficiency and inter-recti separation
following vaginal delivery.30 primiparous post-natal women
participated in this study. Their age ranged from (25 - 35)
years and their BMI < 30 Kg/m2. Participants were assigned
randomly into 2groups, participants of group (A) used
abdominal belt from the 2nd day following delivery, till the end
of puerperium (6 weeks), while participants of group (B)
engaged into abdominal exercises program from the 2nd day
following delivery for 6 weeks. The results of the present
study revealed that although there was no statistical difference
in waist circumference between both groups, participation in
abdominal exercise program produced a pronounced reduction
in waist/hip ratio, and inter-recti separation and also caused
significant increase in abdominal muscles strength (peak
torque, maximum repetition total work and average power)
higher than the use of abdominal belt.
Abstract: This paper focuses on robust design and optimization
of industrial production wastes. Past literatures were reviewed to case
study Clamason Industries Limited (CIL) - a leading ladder-tops
manufacturer. A painstaking study of the firm-s practices at the shop
floor revealed that Over-production, Waiting time, Excess inventory,
and Defects are the major wastes that are impeding their progress and
profitability. Design expert8 software was used to apply Taguchi
robust design and response surface methodology in order to model,
analyse and optimise the wastes cost in CIL. Waiting time and overproduction
rank first and second in contributing to the costs of wastes
in CIL. For minimal wastes cost the control factors of overproduction,
waiting-time, defects and excess-inventory must be set at
0.30, 390.70, 4 and 55.70 respectively for CIL. The optimal value of
cost of wastes for the months studied was 22.3679. Finally, a
recommendation was made that for the company to enhance their
profitability and customer satisfaction, they must adopt the Shingeo
Shingo-s Single Minute Exchange of Dies (SMED), which will
immediately tackle the waste of waiting by drastically reducing their
setup time.
Abstract: Anaerobic treatment has many advantages over other
biological method particularly when used to treat complex
wastewater such as petroleum refinery wastewater. In this study two
Up-flow Anaerobic Sludge Blanket (UASB) reactors were operated
in parallel to treat six volumetric organic loads (0.58, 1.21, 0.89,
2.34, 1.47 and 4.14 kg COD/m3·d) to evaluate the chemical oxygen
demand (COD) removal efficiency. The reactors were continuously
adapting to the changing of operation condition with increase in the
removal efficiency or slight decrease until the last load which was
more than two times the load, at which the reactor stressed and the
removal efficiency decreased to 75% with effluent concentration of
1746 mg COD/L. Other parameters were also monitored such as pH,
alkalinity, volatile fatty acid and gas production rate. The UASB
reactor was suitable to treat petroleum refinery wastewater and the
highest COD removal rate was 83% at 1215 kg/m3·d with COD
concentration about 356 mg/L in the effluent.
Abstract: The article deals with pneumatic and hot wire
anemometry measurement on subsonic axi-symmetric air ejector.
Performances of the ejector with and without pulsations of primary
flow are compared, measuring of characteristic pressures and mass
flow rates are performed and ejector efficiency is evaluated. The
pulsations of primary flow are produced by a synthetic jet generator,
which is placed in the supply line of the primary flow just in front of
the primary nozzle. The aim of the pulsation is to intensify the
mixing process. In the article we present: Pressure measuring of
pulsation on the mixing chamber wall, behind the mixing chamber
and behind the diffuser measured by fast pressure transducers and
results of hot wire anemometry measurement. It was found out that
using of primary flow pulsations yields higher back pressure behind
the ejector and higher efficiency. The processes in this ejector and
influences of primary flow pulsations on the mixing processes are
described.
Abstract: The indistinctness of the manufacturing processes makes that a parts cannot be realized in an absolutely exact way towards the specifications on the dimensions. It is thus necessary to assume that the effectively realized product has to belong in a very strict way to compatible intervals with a correct functioning of the parts. In this paper we present an approach based on mixing tow different characteristics theories, the fuzzy system and Petri net system. This tool has been proposed to model and control the quality in an assembly system. A robust command of a mechanical assembly process is presented as an application. This command will then have to maintain the specifications interval of parts in front of the variations. It also illustrates how the technique reacts when the product quality is high, medium, or low.
Abstract: As every system conceptions the concept of crisis is
based on the system of interdependent elements. These dialectic
elements occur in a majority of definitions even though called
differently. For further theoretical searching but also for practical
utilization it is necessary to understand these elements. The paper
stresses that the concept of crisis is ambiguous. There are identified
and explained the elements that are generally found in most crises
(disruption, precondition, triggers etc).
Abstract: As a company competitiveness depends more and more on the relationship with its stakeholders, the topic of companystakeholder fit is becoming increasingly important. This fit affects the extent to which a stakeholder perceives CSR company commitment, values and behaviors and, therefore, stakeholder identification in a company and his/her loyalty to it. Consequently, it is important to measure the alignment or the gap between stakeholder CSR demands, values, preferences and perceptions, and the company CSR disclosed commitment, values and policies. In this paper, in order to assess the company-stakeholder fit about corporate responsibility, an innovative CSR fit positioning matrix is proposed. This matrix is based on the measurement of a company CSR disclosed commitment and stakeholder perceived and required commitment. The matrix is part of a more complex methodology based on Global Reporting Initiative (GRI) indicators, content analysis and stakeholder questionnaires. This methodology provides appropriate indications for helping companies to achieve CSR company-stakeholder fit, by leveraging both CSR commitment and communication. Moreover, it could be used by top management for comparing different companies and stakeholders, and for planning specific CSR strategies, policies and activities.
Abstract: The purpose of this paper is to highlight the
importance of the concept of competitiveness in the supply chain and
to present a conceptual framework for Supply Chain Competitiveness
(SCC). The framework is based on supply chain activities, which are
inputs, necessary for SCC and the benefits which are the outputs of
SCC. A literature review is conducted on key supply chain
competitiveness issues, its determinants, its various dimensions
followed by exploration for SCC. Based on the insights gained, a
conceptual framework for SCC is presented based on activities for
SCC, SCC environment and outcomes of SCC. The information flow
in the conceptual framework is bi-directional at all levels and the
activities are interrelated in a global competitive environment. The
activities include the activities of suppliers, manufacturers and
distributors, giving more emphasis on manufacturers- activities.
Further, implications of various factors such as economic, politicolegal,
technical, socio-cultural, competition, demographic etc. are
also highlighted. The SCC framework is an attempt to cover the
relatively less explored area of supply chain competitiveness. It is
expected that this work will further motivate researchers,
academicians and practitioners to work in this area and offers
conceptual help in providing a directions for supply chain
competitiveness which leads to improvement in the supply chain and
supply chain performance.
Abstract: Although there are many theories and discussion of leadership, the necessity of having a new leadership paradigm was emphasized. The existing leadership characteristic of instruction and control revealed its limitations. Market competition becomes fierce and economic recession never ends worldwide. Of the leadership theories, servant leadership was introduced recently and is in line with the environmental changes of the organization. Servant leadership is a combination of two words, 'servant' and 'leader' and can be defined as the role of the leader who focuses on doing voluntary work for others with altruistic ethics, makes members, customers, and local communities a priority, and makes a commitment to satisfying their needs. This leadership received attention as one field of leadership in the late 1990s and secured its legitimacy. This study discusses the existing research trends of leadership, the concept, behavior characteristics, and lower dimensions of servant leadership, compares servant leadership with the existing leadership researches and diagnoses if servant leadership is a useful concept for further leadership researches. Finally, this study criticizes the limitations in the existing researches on servant leadership.
Abstract: Higher productivity and less cost in the ship
manufacturing process are required to maintain the international
competitiveness of morden manufacturing industries. In shipbuilding,
however, the Engineering To Order (ETO) production method and
production process is very difficult. Thus, designs change frequently.
In accordance with production, planning should be set up according
to scene changes. Therefore, fixed production planning is very
difficult. Thus, a scheduler must first make sketchy plans, then
change the plans based on the work progress and modifications.
Thus, data sharing in a shipbuilding block assembly shop is very
important. In this paper, we proposed to scheduling method
applicable to the shipbuilding industry and decision making support
system through web based visualization system.
Abstract: The technique of inducing micro ecosystem
restoration is one of aquatic ecology engineering methods used to
retrieve the polluted water. Batch scale study, pilot plant study, and
field study were carried out to observe the eutrophication using the
Inducing Ecology Restorative Symbiosis Agent (IERSA) consisting
mainly degraded products by using lactobacillus, saccharomycete,
and phycomycete. The results obtained from the experiments of the
batch scale and pilot plant study allowed us to development the
parameters for the field study. A pond, 5 m to the outlet of a lake,
with an area of 500 m2 and depth of 0.6-1.2 m containing about 500
tons of water was selected as a model. After the treatment with 10
mg IERSA/L water twice a week for 70 days, the micro restoration
mechanisms consisted of three stages (i.e., restoration, impact
maintenance, and ecology recovery experiment after impact). The
COD, TN, TKN, and chlorophyll a were reduced significantly in the
first week. Although the unexpected heavy rain and contaminate
from sewage system might slow the ecology restoration. However,
the self-cleaning function continued and the chlorophyll a reduced
for 50% in one month. In the 4th week, amoeba, paramecium, rotifer,
and red wriggle worm reappeared, and the number of fish flies
appeared up to1000 fish fries/m3. Those results proved that inducing
restorative mechanism can be applied to improve the eutrophication
and to control the growth of algae in the lakes by gaining the selfcleaning
through inducing and competition of microbes. The
situation for growth of fishes also can reach an excellent result due to
the improvement of water quality.
Abstract: This paper proposes a novel game theoretical
technique to address the problem of data object replication in largescale
distributed computing systems. The proposed technique draws
inspiration from computational economic theory and employs the
extended Vickrey auction. Specifically, players in a non-cooperative
environment compete for server-side scarce memory space to
replicate data objects so as to minimize the total network object
transfer cost, while maintaining object concurrency. Optimization of
such a cost in turn leads to load balancing, fault-tolerance and
reduced user access time. The method is experimentally evaluated
against four well-known techniques from the literature: branch and
bound, greedy, bin-packing and genetic algorithms. The experimental
results reveal that the proposed approach outperforms the four
techniques in both the execution time and solution quality.
Abstract: CONWIP (constant work-in-process) as a pull
production system have been widely studied by researchers to date.
The CONWIP pull production system is an alternative to pure push
and pure pull production systems. It lowers and controls inventory
levels which make the throughput better, reduces production lead
time, delivery reliability and utilization of work. In this article a
CONWIP pull production system was simulated. It was simulated
push and pull planning system. To compare these systems via a
production planning system (PPS) game were adjusted parameters of
each production planning system. The main target was to reduce the
total WIP and achieve throughput and delivery reliability to
minimum values. Data was recorded and evaluated. A future state
was made for real production of plastic components and the setup of
the two indicators with CONWIP pull production system which can
greatly help the company to be more competitive on the market.